BTA40 and BTA/BTB41 Series 40A TRIACS STANDARD MAIN FEATURES: A2 Symbol Value Unit IT(RMS) 40 A V DRM/VRRM 600 and 800 V IGT (Q1) 50 mA DESCRIPTION Available in high power packages, the BTA/ BTB40-41 series is suitable for general purpose AC power switching. They can be used as an ON/ OFF function in applications such as static relays, heating regulation, water heaters, induction motor starting circuits, welding equipment... or for phase control operation in high power motor speed controllers, soft start circuits... Thanks to their clip assembly technique, they provide a superior performance in surge current handling capabilities. By using an internal ceramic pad, the BTA series provides voltage insulated tab (rated at 2500 V RMS) complying with UL standards (File ref.: E81734). G A1 A1 G A2 RD91 (BTA40) A1 A2 A2 A1 A2 G TOP3 Insulated (BTA41) G TOP3 (BTB41) ABSOLUTE MAXIMUM RATINGS Symbol IT(RMS) ITSM It dI/dt Parameter RMS on-state current (full sine wave) Non repetitive surge peak on-state current (full cycle, Tj initial = 25°C) I t Value for fusing Critical rate of rise of on-state current IG = 2 x IGT , tr ≤ 100 ns VDSM/VRSM Non repetitive surge peak off-state voltage IGM PG(AV) Tstg Tj Peak gate current Average gate power dissipation Storage junction temperature range Operating junction temperature range October 2001 - Ed: 4 Value RD91 Tc = 80°C TOP3 A 40 TOP3 Ins. Tc = 70°C F = 60 Hz t = 16.7 ms 420 F = 50 Hz t = 20 ms 400 tp = 10 ms Unit A 880 As F = 120 Hz Tj = 125°C 50 A/µs tp = 10 ms Tj = 25°C V DRM/VRRM V tp = 20 µs Tj = 125°C 8 A Tj = 125°C 1 W - 40 to + 150 - 40 to + 125 °C + 100 1/6 BTA40 and BTA/BTB41 Series ELECTRICAL CHARACTERISTICS (Tj = 25°C, unless otherwise specified) Symbol Test Condition s IGT (1) VD = 12 V Quadrant R L = 33 Ω VD = VDRM R L = 3.3 kΩ IH (2) IT = 500 mA IL IG = 1.2 IGT Unit I - II - III IV MAX. 50 100 mA ALL MAX. 1.3 V ALL MIN. 0.2 V MAX. 80 mA 70 mA VGT V GD Value Tj = 125°C I - III - IV MAX. II 160 VD = 67 % VDRM gate open Tj = 125°C dV/dt (2) (dV/dt)c (2) (dI/dt)c = 20 A/ms Tj = 125°C MIN. 500 V/µs MIN. 10 V/µs STATIC CHARACTERISTICS Symbol VTM (2) Test Conditions ITM = 60 A tp = 380 µs Tj = 25°C Value Unit MAX. 1.55 V Vto (2) Threshold voltage Tj = 125°C MAX. 0.85 V Rd (2) Dynamic resistance Tj = 125°C MAX. 10 mΩ I DRM VDRM = VRRM Tj = 25°C 5 µA 5 mA Value Unit MAX. Tj = 125°C I RRM Note 1: minimum IGT is guaranted at 5% of IGT max. Note 2: for both polarities of A2 referenced to A1 THERMAL RESISTANCES Symbol Parameter Junction to case (AC) Rth(j-c) RD91 (Insulated) TOP3 0.9 TOP3 Insulated 1.2 Junction to ambient R th(j-a) TOP3 TOP3 Insulated 50 °C/W °C/W PRODUCT SELECTOR Voltage (xxx) Part Number Sensitivity Type Package X 50 mA Standard RD91 X 50 mA Standard TOP3 600 V 800 V BTA40-xxxB X BTA/BTB41-xxxB X BTB: Non insulated TOP3 package 2/6 BTA40 and BTA/BTB41 Series ORDERING INFORMATION BT A 40 - 600 B TRIAC SERIES SENSITIVITY: B: 50mA INSULATION: A: insulated B: non insulated VOLTAGE: 600: 600V 800: 800V CURRENT: 40: 40A in RD91 41: 40A in TOP3 OTHER INFORMATION Part Number Marking Weight Base quantity Packing mode BTA40-xxxB BTA40xxxB 20.0 g 25 Bulk BTA/BTB41-xxxB BTA/BTB41xxxB 4.5 g 120 Bulk Note: xxx= voltage Fig. 1: Maximum power dissipation versus RMS on-state current (full cycle). Fig. 2: RMS on-state current versus case temperature (full cycle). P (W) 50 45 40 35 30 25 20 15 10 5 40 30 20 10 IT(RMS) (A) 0 0 5 10 15 20 25 30 35 40 0 IT(RMS) (A) BTA40/BTB41 BTA41 Tc(°C) 0 25 50 75 100 125 3/6 BTA40 and BTA/BTB41 Series Fig. 3: Relative variation of thermal impedance versus pulse duration. Fig. 4: values). On-state characteristics (maximum ITM (A) K=[Zth/Rth] 400 1E+0 Zth(j-c) Tj max 100 1E-1 Zth(j-a) BTA/BTB41 Tj=25°C 10 1E-2 tp (s) 1E-3 1E-3 1E-2 1E-1 1E+0 VTM (V) 1E+1 1E+2 5E+2 Fig. 5: Surge peak on-state current versus number of cycles. 1 0.5 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 ITSM (A),I t (A s) 3000 ITSM t=20ms One cycle Non repetitive Tj initial=25°C 1000 dI/dt limitation: 50A/µs It Repetitive Tc=70°C tp (ms) Number of cycles 1 10 100 1000 Fig. 7: Relative variation of gate trigger current, holding current and latching current versus junction temperature (typical values). 100 0.01 1.00 10.00 (dI/dt)c [(dV/dt)c] / Specified (dI/dt)c 2.0 1.8 2.0 1.6 IGT 1.4 1.5 1.2 IH & IL 1.0 1.0 0.8 0.5 0.6 Tj(°C) 0.0 -40 0.10 Tj initial=25°C Fig. 8: Relative variation of critical rate of decrease of main current versus (dV/dt)c (typical values). IGT,IH,IL[Tj] / IGT,IH,IL [Tj=25°C] 2.5 4/6 1.0 Fig. 6: Non-repetitive surge peak on-state current for a sinusoidal pulse with width tp < 10 ms, and corresponding value of I t. ITSM (A) 450 400 350 300 250 200 150 100 50 0 Tj max.: Vto = 0.85 V Rd = 10 mΩ -20 0 20 40 60 80 100 120 140 0.4 0.1 (dV/dt)c (V/µs) 1.0 10.0 100.0 BTA40 and BTA/BTB41 Series Fig. 9: Relative variation of critical rate of decrease of main current versus junction temperature. (dI/dt)c [Tj] / (dI/dt)c [Tj specified] 6 5 4 3 2 1 0 Tj (°C) 0 25 50 75 100 125 PACKAGE MECHANICAL DATA RD91 (Plastic) DIMENSIONS L2 A2 L1 REF. Millimeters Min. B2 B1 C C2 C1 A1 N2 N1 B F E3 I A A A1 A2 B B1 B2 C C1 C2 E3 F I L1 L2 N1 N2 29.90 13.50 1.95 0.70 4.00 11.20 3.10 1.70 33° 28° Max. 40.00 30.30 22.00 27.00 16.50 24.00 14.00 3.50 3.00 0.90 4.50 13.60 3.50 1.90 43° 38° Inches Min. 1.177 0.531 0.077 0.027 0.157 0.441 0.122 0.067 33° 28° Max. 1.575 1.193 0.867 1.063 0.650 0.945 0.551 0.138 0.118 0.035 0.177 0.535 0.138 0.075 43° 38° 5/6 BTA40 and BTA/BTB41 Series PACKAGE MECHANICAL DATA TOP3 Ins.(Plastic) DIMENSIONS REF. Millimeters Min. A B C D E F G H J K L P R Typ. 4.4 1.45 14.35 0.5 2.7 15.8 20.4 15.1 5.4 3.4 4.08 1.20 Inches Max. Min. 4.6 1.55 15.60 0.7 2.9 16.5 21.1 15.5 5.65 3.65 4.17 1.40 0.173 0.057 0.565 0.020 0.106 0.622 0.815 0.594 0.213 0.134 0.161 0.047 4.60 Typ. Max. 0.181 0.061 0.614 0.028 0.114 0.650 0.831 0.610 0.222 0.144 0.164 0.055 0.181 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A http ://www.st.com 6/6