HCF4066B QUAD BILATERAL SWITCH FOR TRANSMISSION OR MULTIPLEXING OF ANALOG OR DIGITAL SIGNALS ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 15V DIGITAL OR ± 7.5V PEAK TO PEAK SWITCHING 125Ω TYPICAL ON RESISTANCE FOR 15V OPERATION SWITCH ON RESISTANCE MATCHED TO WITHIN 5Ω TYP. OVER 15V SIGNAL INPUT RANGE ON RESISTANCE FLAT OVER FULL PEAK TO PEAK SIGNAL RANGE HIGH ON/OFF OUTPUT VOLTAGE RATIO : 65dB TYP. at fIS = 10KHz, RL = 10KΩ HIGH DEGREE OF LINEARITY : < 0.5% DISTORTION TYP. at fIS = 1KHz, VIS = 5 Vpp, VDD - VSS > 10V, RL = 10KΩ EXTREMELY LOW OFF SWITCH LEAKAGE RESULTING IN VERY LOW OFFSET CURRENT AND HIGH EFFECTIVE OFF RESISTANCE : 10pA TYP. at VDD - VSS = 10V, Tamb = 25°C EXTREMELY HIGH CONTROL INPUT IMPEDANCE (control circuit isolated from signal circuit 1012Ω typ.) LOW CROSSTALK BETWEEN SWITCHES : 50dB Typ. at fIS = 0.9MHz, RL = 1KΩ MATCHED CONTROL - INPUT TO SIGNAL OUTPUT CAPACITANCE : REDUCES OUTPUT SIGNAL TRANSIENTS FREQUENCY RESPONSE SWITCH ON : 40MHz (Typ.) QUIESCENT CURRENT SPECIF. UP TO 20V 5V, 10V AND 15V PARAMETRIC RATINGS DIP SOP ORDER CODES PACKAGE TUBE T&R DIP SOP HCF4066BEY HCF4066BM1 HCF4066M013TR ■ ■ ■ INPUT LEAKAGE CURRENT II = 100nA (MAX) AT VDD = 18V TA = 25°C 100% TESTED FOR QUIESCENT CURRENT MEETS ALL REQUIREMENTS OF JEDEC JESD13B ” STANDARD SPECIFICATIONS FOR DESCRIPTION OF B SERIES CMOS DEVICES” DESCRIPTION The HCF4066B is a monolithic integrated circuit fabricated in Metal Oxide Semiconductor technology available in DIP and SOP packages. The HCF4066B is a QUAD BILATERAL SWITCH intended for the transmission or multiplexing of analog or digital signals. It is pin for pin compatible with HCF4016B, but exhibits a much lower ON resistance. In addition, PIN CONNECTION September 2001 1/9 HCF4066B the ON resistance is relatively constant over the full input signal range. The HCF4066B consists of four independent bilateral switches. A single control signal is required per switch. Both the p and n device in a given switch are biased ON or OFF simultaneously by the control signal. As shown in schematic diagram , the well of the n-channel device on each switch is either tied to the input when the switch is ON or to VSS when the switch is OFF. This configuration eliminates the variation of the switch-transistor threshold voltage with input signal, and thus keeps the ON resistance low over the full operating signal range. The advantages over single channel switches include peak input signal voltage swings equal to the full supply voltage, and more constant ON impedance over the input signal range. For sample and hold applications, however, the HCF4016B is recommended. INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL 1, 4, 8, 11 A to D I/O 2, 3, 9, 10 A to D O/I NAME AND FUNCTION Independent Inputs/Outputs Independent Outputs/ Inputs 7 CONTROL A to D VSS Negative Supply Voltage 14 VDD Positive Supply Voltage 13, 5, 6, 12 Enable Inputs TRUTH TABLE CONTROL SWITCH FUNCTION H L ON OFF SCHEMATIC DIAGRAM (1 OF 4 IDENTICAL SWITCHES AND ITS ASSOCIATED CONTROL CIRCUITY) 2/9 HCF4066B ABSOLUTE MAXIMUM RATINGS Symbol V DD Parameter Supply Voltage Value Unit -0.5 to +22 V VI DC Input Voltage -0.5 to VDD + 0.5 V II DC Input Current ± 10 mA 200 100 mW mW Top Power Dissipation per Package Power Dissipation per Output Transistor Operating Temperature -55 to +125 °C Tstg Storage Temperature -65 to +150 °C PD Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. All voltage values are referred to VSS pin voltage. RECOMMENDED OPERATING CONDITIONS Symbol V DD Parameter Supply Voltage VI Input Voltage Top Operating Temperature Value Unit 3 to 20 V 0 to VDD V -55 to 125 °C ELECTRICAL CHARACTERISTICS (Tamb = 25°C,Typical temperature coefficient for all VDD value is 0.3 %/°C) Test Condition Value TA = 25°C Symbol Parameter VI (V) VDD (V) Typ. Max. IL Quiescent Device Current (all switches ON or all switches OFF) 0/5 0/10 0/15 0/20 5 10 15 20 0.01 0.01 0.01 0.02 0.25 0.5 1 5 7.5 15 30 150 7.5 15 30 150 µA 5 10 15 5 RL = 10KΩ, VC = VDD 10 15 VC = VDD = 5V, VSS = -5V VIS (p-p) = 5V, R L = 10KΩ (sine wave centered in 0V) fIS = 1KHz sine wave 470 180 125 5 10 15 0.4 1050 400 240 1200 500 300 1200 500 300 Ω VC = VDD = 5V, VSS = -5V VIS (p-p) = 5V, R L = 1KΩ (sine wave centered in 0V) VC = VSS = -5V VIS (p-p) = 5V, R L = 1KΩ (sine wave centered in 0V) 40 MHz 1 MHz Min. -40 to 85°C -55 to 125°C Min. Max. Min. Unit Max. SIGNAL INPUTS (V IS) and OUTPUTS (VOS) R ON ∆ON TDH Resistance Resistance ∆RON (between any 2 of 4 switches) Total Harmonic Distortion -3dB Cutoff Frequency (Switch on) -50dB Feedthrough Frequency (switch off) VC=V DD RL = 10KΩ Return to (VDD-VSS)/2 VIS = VSS to VDD Ω % 3/9 HCF4066B Test Condition Symbol Parameter -50dB Crosstalk Frequency tpd Propagation Delay Time (signal input to output) CIS Input Capacitance COS Output Capacitance C IOS Feedthrough VI (V) Value VDD (V) TA = 25°C Min. Typ. VC(A) = VDD = +5V VC(B) = VSS = - 5V VIS(A) = 5V (p-p) 50Ω source, RL = 1KΩ 8 RL = 200KΩ, VC = VDD VSS = GND, CL = 50pF VIS= 10V square wave centered on 5V tr, tf = 20ns 20 10 7 -40 to 85°C -55 to 125°C Max. Max. Min. Max. MHz 40 20 15 ns 8 VC = VSS = -5 8 +5 pF 0.5 VC = 0V VIS = 18V, V OS = 0V VIS = 0V, VOS = 18V 18 IIS< 10 µA V IS = VSS, VOS = V DD and V IS = VDD, VOS = VSS 5 10 15 5 10 15 VIS < VDD VDD - VSS = 18V 18 ±10 -5 Crosstalk (control input to signal output) VC = 10V (sq. wave) tr, tf = 20ns R L = 10KΩ 10 50 Turn - On Propagation Delay Time VIN = V DD, tr, tf = 20ns CL = 50pF, R L = 1KΩ 5 10 15 5 10 15 35 20 15 6 9 9.5 70 40 30 5 7.5 Input/Output Leakage Current Switch OFF Min. Unit ±10 -3 ±0.1 ±1 ±1 µA 1 2 2 1 2 2 1 2 2 V CONTROL (VC) VILC VIHC II Control Input Low Voltage Control Input High Voltage Input Leakage Current Control Input Repetition Rate CI 4/9 Input Capacitance VIS=V DD, VSS=GND R L = 1KΩ to GND C L = 50pF, V C = 10V sq. wave center on 5V tr, tf = 20ns VOS=1/2VOS at 1KHz Any Input 3.5 7 11 3.5 7 11 ±0.1 3.5 7 11 ±1 V ±1 µA mV ns MHz pF HCF4066B TYPICAL APPLICATIONS (BIDIRECTIONAL SIGNAL TRANSMISSION VIA DIGITAL CONTROL LOGIC) TYPICAL APPLICATIONS (4-CHANNEL PAM MULTIPLEXER SYSTEM DIAGRAM) 5/9 HCF4066B TEST CIRCUIT C L = 50pF or equivalent (includes jig and probe capacitance) R L = 200KΩ R T = ZOUT of pulse generator (typically 50Ω) WAVEFORM : PROPAGATION DELAY TIMES (f=1MHz; 50% duty cycle) 6/9 HCF4066B Plastic DIP-14 MECHANICAL DATA mm. inch DIM. MIN. a1 0.51 B 1.39 TYP MAX. MIN. TYP. MAX. 0.020 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 I 5.1 0.201 L Z 3.3 1.27 0.130 2.54 0.050 0.100 P001A 7/9 HCF4066B SO-14 MECHANICAL DATA DIM. mm. MIN. TYP A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 8.55 8.75 0.336 0.344 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 7.62 0.300 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.68 0.026 8° (max.) PO13G 8/9 HCF4066B Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringe ment of patents or other righ ts of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this pub lication are subject to change without notice. Thi s pub lication supersedes and replaces all information previously supplied. STMicroelectronics prod ucts are not authori zed for use as critical components in life suppo rt devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Swit zerland - United Kingdom http://w ww.st.com 9/9