TDA2004A 10 + 10W STEREO AMPLIFIER FOR CAR RADIO Its main features are : Low distortion. Low noise. High reliability of the chip and of the package with additional safety during operation thanks to protections against : OUTPUT AC SHORT CIRCUIT TO GROUND VERY INDUCTIVE LOADS OVERRATING CHIP TEMPERATURE LOAD DUMP VOLTAGE SURGE FORTUITOUS OPEN GROUND Space and cost saving : very low number of external components, very simple mounting system with no electrical isolation between the package and the heatsink. .. .. . DESCRIPTION The TDA2004A is a class B dual audio power amplifier in MULTIWATT package specifically desi- MULTIWATT11 ORDERING NUMBER : TDA2004A gned for car radio applications ; stereoamplifiers are easily designed using this device that provides a high current capability (up to 3.5 A) and that can drive very low impedance loads (down to 1.6Ω ). PIN CONNECTION (top view) March 1995 1/10 TDA2004A ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit VS Opearting Supply Voltage 18 V VS DC Supply Voltage 28 V VS Peak Supply Voltage (for 50ms) 40 V Output Peak Current (non repetitive t = 0.1ms) 4.5 A IO (*) Output Peak Current (repetitive f ≥ 10Hz) 3.5 A Ptot Power Dissipation at Tcase = 60°C 30 W Tj, Tstg Storage and Junction Temperature –40 to 150 °C IO (*) (*) The max. output current is internally limited. THERMAL DATA Symbol Parameter Rth j-case Thermal Resistance Junction-case Max. Value Unit 3 °C/W ELECTRICAL CHARACTERISTICS (Refer to the test circuit, Tamb = 25°C, GV = 50dB, Rth (heatsink) = 4°C/W, unless otherwise specified) Symbol Parameter Test Condition VS Supply Voltage VO Quiescent Output Voltage VS = 14.4V VS = 13.2V Id Total Quiescent Drain Current ISB PO Min. CT Vi 2/10 Max. Unit 18 V 7.2 6.6 7.8 7.2 V V VS = 14.4V VS = 13.2V 65 62 120 120 mA mA Stand-by Current Pin 3 grounded 5 mA Output Power (each channel) f = 1KHz, d = 10% 6.6 6.0 VS = 14.4V RL = 4Ω RL = 3.2Ω RL = 2Ω RL= 1.6Ω 6 7 9 10 6.5 8 10(*) 11 W W W W VS = 13.2V RL = 3.2Ω RL= 1.6Ω 6 9 6.5 10 w w 12 w VS = 16V; R L = 2Ω d Typ. 8 Distortion (each channel) Cross Talk Input Saturation Voltage f = 1KHz VS = 14.4V; RL = 4Ω PO = 50mW to 4W VS = 14.4V; RL = 2Ω PO = 50mW to 6W VS = 13.2V; RL = 3.2Ω PO = 50mW to 3W VS = 13.2V; RL = 1.6Ω PO = 50mW to 6W VS = 14.4V VO = 4Vrms RL = 4Ω f = 1KHz f = 10KHz R g = 5KΩ 50 40 300 0.2 1 % 0.3 1 % 0.2 1 % 0.3 1 % 60 45 dB dB mV TDA2004A ELECTRICAL CHARACTERISTICS (continued Symbol Parameter Test Condition Ri Input Resistance (non inverting input) f = 1KHz fL Low Frequency Roll off (-3dB) RL = 4Ω RL = 2Ω RL = 3.2Ω RL= 1.6Ω fH High Frequency Roll off (-3dB) RL = 1.6Ω to 4Ω GV Voltage gain (open loop) f = 1KHz Voltage gain (closed loop) f = 1KHz Min. Typ. 70 200 15 Total Input noise Voltage Rg = 10KΩ (**) SVR Supply Voltage Rejection fripple = 100Hz; R g = 10KΩ C3 = 10µF Vripple = 0.5Vrms Efficiency VS = 14.4V RL = 4Ω RL = 2Ω VS = 13.2V RL = 3.2Ω RL = 1.6Ω TJ 50 dB 51 dB 5 µV 0.5 eN Thermal Shutdown Junction Temperature f = 1KHz PO = 6.5W PO = 10W f = 1KHZ PO = 6.5W PO = 10W 1.5 35 Hz Hz Hz Hz KHz 90 48 Unit KΩ 35 50 40 55 closed loop gain matching η Max. dB 45 dB 70 60 % % 70 60 % % 145 °C Notes : (*) 9.3W without Bootstrap (**) Bandwith Filter : 22Hz to 22KHz. Figure 1 : Test and Application Circuit. 3/10 TDA2004A Figure 2 : P.C. Board and Component layout of the fig. 1 (scale 1 : 1). Figure 3 : Quiescent Output Voltage vs. Supply Voltage. 4/10 Figure 4 : Quiescent Drain Current vs. Supply Voltage. TDA2004A Figure 5 : Distortion vs. Output Power. Figure 6 : Output Power vs. Supply Voltage. Figure 7 : Output Power vs. Supply Voltage. Figure 8 : Distortion vs. Frequency. Figure 9 : Distortion vs. Frequency. Figure 10 : Supply Voltage Rejection vs. C3. 5/10 TDA2004A Figure 11 : Supply Voltage Rejection vs. Frequency. Figure 12 : Supply Voltage Rejection vs. Values of Capacitors C2 and C3. Figure 13 : Supply Voltage Rejection vs. Values of Capacitors C2 and C3. Figure 14 : Gain vs. Input Sensitivity. Figure 15 : Maximum Allowable Power Dissipation vs. Ambient Temperature. Figure 16 : Total Power Dissipation and Efficiency vs. Output Power. 6/10 TDA2004A Figure 17 : Total Power Dissipation and Efficiency vs. Output Power . APPLICATION SUGGESTION The recommended values of the componentsare those shown on application circuit of fig.1. Different values can be used ; the following table can help the designer. Component Recomm. Value R1 120KΩ R2, R4 1KΩ R3, R5 3.3Ω R6, R7 1Ω C1, C2 Purpose Larger Than Smaller Than Optimization of the Smaller PO max. output signal simmetry Smaller PO max. Close loop gain setting (*) Increase of gain Decrease of gain Decrease of gain Increase of gain Frequency stability Danger of oscillation at high frequency with inductive load 2.2µF Input DC decoupling High turn-on delay C3 10µF Ripple Rejection Increase of SVR. Degradation of SVR. Increase of the switchon time. C4, C6 100µF Boostrapping C5, C7 100µF Feedback Input DC decoupling. C8, C9 0.1µF Frequency Stability Danger of oscillation. C10, C11 1000µF to 2200µF Output DC decoupling. Higher low-frequency cut-off. High turn-on pop Higher low frequency cutoff. Increase of noise Increase of distortion at low frequency (*) The closed–loop gain must be higher than 26dB. 7/10 TDA2004A BUILT–IN PROTECTION SYSTEMS LOAD DUMP VOLTAGE SURGE The TDA2004A has a circuit which enables it to withstand a voltage pulse train, on pin 9, of the type shown in Fig. 19. If the supply voltage peaks to more than 40 V, then an LC filter must be insertedbetweenthe supplyand pin 9, in order to assure that the pulses at pin 9 will be held within the limits shown. A suggested LC network is shown in Fig. 18. With this network, a train of pulsewith amplitude up to 120 V and with of 2 ms can be applied to point A. This type of protection is ON when the supply voltage (pulse or DC) exceeds18 V. For this reason the maximum operating supply voltage is 18 V. POLARITY INVERSION High current (up to 10 A) can be handled by the device with no damage for a longer period than the blow-out time of a quick 2 A fuse (normally connected in series with the supply). This feature is added to avoid destruction, if during fitting to the car, a mistake on the connection of the supply is made. Figure 18. A protection diode is provided to allow use of the TDA2004A with inductive loads. OPEN GROUND When the ratio is the ON condition and the ground is accidentally opened, a standard audio amplifier will be damaged. On the TDA2004A protection diodes are included to avoid any damage. INDUCTIVE LOAD DC VOLTAGE The maximum operating DC voltage on the TDA2004A is 18 V. However the device can withstand a DC voltage up to 28V withno damage. This could occurduring winter if two batteries are series connected to crank the engine. Figure 19. THERMAL SHUT-DOWN SHORT CIRCUIT (AC conditions) The TDA2004A can withstand an accidental shortcircuit from the output to ground caused by a wrong connection during normal working. The presence of a thermal limiting circuit offers the following advantages : 1) an overloadon the output(even if it is permanent), or an excessive ambient temperature can be easily withstood. 2) the heatsink can have a smaller factor of safety compared with that of a conventional circuit. There is no device damage in the case of excessive junction temperature ; all that happens is the PO (and therefore Ptot) and Id are reduced. The maximum allowable power dissipationdepends upon the size of the external heatsink(i.e. its thermal resistance) ; fig. 15 shown this dissipable power as a function of ambient temperature for different thermal resistance. 8/10 TDA2004A MULTIWATT11 PACKAGE MECHANICAL DATA DIM. A B C D E F G G1 H1 H2 L L1 L2 L3 L4 L7 M M1 S S1 Dia1 MIN. mm TYP. MAX. 5 2.65 1.6 MIN. 0.55 0.95 1.95 17.25 0.019 0.035 0.057 0.659 0.772 1 0.49 0.88 1.45 16.75 19.6 21.9 21.7 17.4 17.25 10.3 2.65 4.25 4.73 1.9 1.9 3.65 1.7 17 22.2 22.1 17.5 10.7 4.55 5.08 inch TYP. MAX. 0.197 0.104 0.063 0.039 20.2 22.5 22.5 18.1 17.75 10.9 2.9 4.85 5.43 2.6 2.6 3.85 0.862 0.854 0.685 0.679 0.406 0.104 0.167 0.186 0.075 0.075 0.144 0.067 0.669 0.874 0.87 0.689 0.421 0.179 0.200 0.022 0.037 0.077 0.679 0.795 0.886 0.886 0.713 0.699 0.429 0.114 0.191 0.214 0.102 0.102 0.152 9/10 TDA2004A Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics. 1995 SGS-THOMSON Microelectronics - All Rights Reserved MULTIWATT is a Registered Trademark of SGS-THOMSON Microelectronics SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands - Singapore Spain - Sweden - Switzerland - Taiwan - Thaliand - United Kingdom - U.S.A. 10/10