MIC2310 Single-FET, Constant Power-Limit Hot Swap Controller General Description Features The MIC2310 is a single-channel, positive voltage, constant power-limit hot swap controller designed to provide for the safe insertion and removal of pc boards into fixed, rack, and pedestal mid- or back-planes using few external components. In addition, the MIC2310 employs a patent-pending, output load power-limiting technique where the current limit is inversely proportional to the output load voltage, such that the power product will not exceed the programmed power limit any longer than the externally programmed primary overcurrent period. The MIC2310 is ideally suited to address the power-limiting and timing requirements per the UL60950 specification for 240-VA applications. The MIC2310 incorporates high-side controller circuitry for an external N-channel MOSFET for which the MOSFET drain current rate of change is userprogrammable via an external capacitor. The MIC2310 employs dual-speed, dual-level overcurrent fault protection. The primary overcurrent detector response time is programmable via an external current sense resistor and the secondary overcurrent detector is 2-bit userprogrammable and exhibits a very fast (default) response to faults to ensure that the system power supplies are protected against catastrophic load current and shortcircuit faults. Additionally, an analog output (voltage) signal is provided that is proportional to the steady-state load current to allow monitoring of the system’s power. A PWRGD signal is provided to indicate a valid output voltage that can be used to enable a DC-DC power module. Data sheets and support documentation can be found on Micrel’s web site at www.micrel.com. • • • • • • • • Provides safe PCB insertion and removal from live +12V backplanes Patent-pending, adaptive circuit breaker threshold control – Maintains constant power product at output – Power-limit product (VA) is externally programmable for various power applications Dual-level, dual-speed overcurrent detection/protection – Programmable primary detector response time – Fast (< 1 µs) secondary detector response time to short circuit conditions User-programmable threshold settings via (2) digital inputs Steady-state load current monitoring Programmable inrush current slew-rate control Electronic circuit breaker functions after fault – Latch off – Automatic retry Programmable input undervoltage lockout and overvoltage protection Fault reporting: – Open-drain ‘Power-is-Good’ output – Open-drain ‘I_FLT’ output signaling for all current faults – Shorted RSENSE and Damaged MOSFET detection (D-G and D-S shorts) Applications • • • • • • • UL60950, EN60950, and CSA1950 systems (240-VA) General Power-limiting Applications Base stations Enterprise servers High-reliability servers Enterprise switch networks +12V backplanes Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com July 2008 M9999-070108-A Micrel, Inc. MIC2310 Typical Application RSENSE VIN 12V 1 C2* 0.5% 3 Q1 IRL3713S D2Pak 2 4 R1 R2 C3 0.68µF R3 C1 1.5µF 1% VOUT 12V@20A 24 VCC 6 ENABLE 1 UVLO R4 1% R5 2 1% 7 23 VCCSENSE 22 SENSE C4 0.47µF 11 CSLEW 10 C7 0.01µF 21 CPRIMARY 19 GATE SOURCE LOADSENSE GNDSENSE 17 DISCH 16 VREG 4 3 OVP MIC2310 S0 CDISCH Q2 ZUMT618 SOT-323 C6 0.1µF S1 VISS TO SYSTEM MANAGEMENT CONTROLLER R9 CLOAD S[1,0]=X,X 8 18 CRETRY 3 9 CPGND AGND 20 HW_FLT 12 13 PWRGD 14 C5 0.068µF I_FLT 15 R8 V LOGIC R7 R6 Overcurrent Fault Output * The value of C2 is flexible and dependant upon the parasitic inductance, which should be minimzed as much as possible. A inductance) for C2 is 56µF, minimum July 2008 Power-Good Output Hardware Fault Output 2 M9999-070108-A Micrel, Inc. MIC2310 Ordering Information Part Number PWRGD State I_FLT State Fault Condition Status Package Lead Finish MIC2310-1ZTS Active-HIGH Active-HIGH Latched/Auto-retry 24-pin TSSOP Pb-Free MIC2310-2ZTS Active-LOW Active-LOW Latched/Auto-retry 24-pin TSSOP Pb-Free Note: 1. Other Voltage available. Contact Micrel for details. Pin Configuration UVLO 1 24 VCC UVLO 1 24 VCC OVP 2 23 VCCSENSE OVP 2 23 VCCSENSE VISS 3 22 SENSE VISS 3 22 SENSE VREG 4 21 GATE VREG 4 21 GATE NC 5 20 CPGND NC 5 20 CPGND ENABLE 6 19 SOURCE ENABLE 6 19 SOURCE S0 7 18 LOADSENSE S0 7 18 LOADSENSE S1 8 17 GNDSENSE S1 8 17 GNDSENSE CRETRY 9 16 DISCH CRETRY 9 16 DISCH CPRIMARY 10 15 /I_FLT CPRIMARY 10 15 I_FLT CSLEW 11 14 PWRGD CSLEW 11 14 /PWRGD AGND 12 13 HW_FLT AGND 12 13 HW_FLT 24-pin TSSOP (TS) MIC2310-1ZTS July 2008 24-pin TSSOP (TS) MIC2310-2ZTS 3 M9999-070108-A Micrel, Inc. MIC2310 Pin Description Pin Number Pin Name 1 UVLO Undervoltage Lockout Input. When the applied voltage at the UVLO pin is higher than the controller’s VUVLOH threshold voltage, the GATE drive circuits are active when ENABLE= HIGH. If the applied voltage at the UVLO pin falls below the controller’s VUVLOL threshold voltage, the GATE drive circuits are disabled to turn the external MOSFET OFF. In addition, the DISCH circuit is activated to drive an optional, external discharge transistor alone (illustrated in the Typical Application circuit) or in combination with an SCR for a very fast discharge circuit configuration. 2 OVP Overvoltage Protection Input. When the applied voltage at the OVP pin is higher than the controller’s VOVPH threshold voltage, the GATE drive circuit is disabled to turn the external MOSFET OFF. In addition, the DISCH circuit is activated to drive an optional, external discharge transistor alone (illustrated in the Typical Application circuit) or in combination with an SCR for a very fast discharge circuit configuration. Using an external resistor divider, the UVLO and the OVP pins form a window comparator that defines the supply voltage range within which the load may be safely powered. 3 VISS Steady-state Output Current Monitor. This output signal provides an analog voltage that is proportional to the steady-state load current. This signal is provided as an input to the system supervisor/processor to monitor the dc current/power level of the application circuit. 4 VREG Internal +5V Regulator Bypass. Connect a 0.1-µF, 16V ceramic capacitor from this pin to AGND. 5 NC 6 ENABLE ENABLE Input. An active asserted-HIGH digital input that controls the operation of the MIC2310. Activated after the internal POR timer has terminated, a LOWto-HIGH transition on this pin commences a start-up sequence if the applied VCC is above the VUVLOH and below the VOVPH threshold voltages. While ENABLE = LOW, the GATE pin is held to 0V and the DISCH output is activated. The ENABLE input can be used to reset the internal circuit breaker by applying a HIGH-to-LOW-to-HIGH transition as defined by tENLPW following either a load current fault, an open LOADSENSE fault, an open GNDSENSE fault, or a shorted RSENSE fault. 7 S0 8 S1 Secondary OC Detector Current Threshold Digital Inputs – S1 is the MSB and S0 is the LSB. When used together, S[1:0] sets the overcurrent threshold for the secondary overcurrent detection circuit to one of four levels relative to the primary overcurrent detector nominal threshold. For example, S[1:0] = L, L sets the secondary overcurrent threshold at 1.3X; S[1:0] = L, H sets a 1.5X threshold; S[1:0] = H, L sets a 2X threshold, and S[1:0] = H, H sets a 1.75X threshold. If the S[1:0] pins are not connected or left NC, the default setting is S[1:0] = L, L or 1.3X. The permissible voltage range on these inputs is AGND ≤ S[1:0] ≤ VCC. 9 CRETRY Auto-retry Timing Capacitor. A capacitor connected from the CRETRY pin to AGND configures the MIC2310 to re-start automatically with ENABLE = HIGH after the circuit breaker trips and latches off. It also sets the “cool-off” time delay before a new load current start-up sequence is initiated. To configure the MIC2310’s circuit breaker to latch off after fault, connect this pin to AGND. The circuit breaker latches OFF and remains latched OFF unless the ENABLE input is toggled HIGH-to-LOW-to-HIGH as defined by tENLPW or the VCC supply voltage is turned OFF then ON. 10 CPRIMARY Primary Overcurrent Detector Timing Capacitor. Connecting a capacitor from the CPRIMARY pin to AGND sets the response time of the controller’s primary overcurrent detection circuit to GATE OFF in the event of an overcurrent condition. If the CPRIMARY pin is not connected, the primary overcurrent detection response time defaults to tPOCSENSE, typically 250µs as specified in the Electrical Characteristics Table. The controller incorporates a patent-pending built-in test for a faulty CPRIMARY capacitor. July 2008 Pin Function No connection 4 M9999-070108-A Micrel, Inc. MIC2310 Pin Description (continued) Pin Number Pin Name 11 CSLEW 12 AGND 13 HW_FLT Pin Function Inrush Current Slew Rate Control Input. To adjust the inrush load current profile (controlled dIDRAIN/dt), connect a capacitor from this pin to VCC. To adjust the MOSFET GATE voltage profile (controlled dVGATE/dt), leave this pin OPEN (floating) and connect a capacitor from GATE to AGND. For additional information on the operation of this function, please refer to the Functional Description section. Analog Ground. Connect this pin to the system analog ground plane. External MOSFET Hardware Fault Digital Output. This output is an open-drain, active-HIGH signal that should be connected to a +3.3V logic supply by a 10kΩ resistor. This digital output is active after the internal POR timer has terminated and becomes asserted (HIGH) due to a fault under the following conditions: a) a shorted DG MOSFET with ENABLE = LOW; b) a shorted DS MOSFET with ENABLE = LOW; c) a shorted RSENSE; d) a shorted DS MOSFET after steadystate operation with ENABLE = HIGH-to-LOW; or e) a shorted DG or DS while EN = HIGH and DISCH = HIGH; or f) a shorted CPRIMARY to AGND. The HW_FLT output is latched and is reset when VCC is brought low such that VREG < VVREG(UVLO). 14 PWRGD /PWRGD 15 I_FLT /I_FLT July 2008 Power Good Digital Output. This output is an open-drain, active-HIGH (PWRGD) or active-LOW (/PWRGD) signal that should be connected to a +3.3-V logic supply by a 10kΩ resistor. This digital output is active after the internal POR timer has terminated and becomes asserted when the voltage between the LOADSENSE and the GNDSENSE pins is higher than the controller’s VPGH threshold voltage. It is de-asserted when the voltage between the LOADSENSE and the GNDSENSE pins is less than the controller’s VPGL threshold voltage. Load Current Fault Digital Output. This output is an open-drain, active-HIGH (I_FLT) or active-LOW (/I_FLT) signal that should be connected to a +3.3V logic supply by a 10kΩ resistor. This digital output is active after the internal POR timer has terminated and becomes asserted whenever the primary or secondary overcurrent detection circuits cause the internal circuit breaker to latch OFF. The digital output remains asserted unless the ENABLE input is toggled HIGH-toLOW-to-HIGH as defined by tENLPW or the VCC supply voltage is turned OFF then ON or if the auto-retry mode is enabled. Discharge External Transistor Drive Output. When ENABLE = LOW or after a fault condition (either an overcurrent fault or hardware fault such as a shorted MOSFET) that causes either the primary and secondary overcurrent detectors to trip the internal circuit breaker, the DISCH circuit is activated to provide gate drive to optional, external transistors (and SCR, for very fast load discharge). These transistors serve as auxiliary gate pull-down or load voltage pull-down switches. A load voltage pull-down is illustrated in the Typical Application circuit. 16 DISCH 17 GNDSENSE 18 LOADSENSE 19 SOURCE External Power MOSFET Source Pin Monitor. To protect external circuits downstream of the controller, internal monitor circuits are included to sense a shorted drain-source condition of the external power MOSFETs. 20 CPGND Internal charge pump power ground. Connect this pin directly to the system’s analog ground plane. 21 GATE These input pins (when used together) sense the load voltage and provide feedback to the controller’s adaptive VA limit and Power-Good circuits. The voltage across these two pins also sets the controller’s Power-Is-Good status output as defined by the specified VPGH or the VPGL threshold voltages. Internal circuit monitors are included if either or both LOADSENSE and GNDSENSE connections are severed or not connected to the load. External N-channel MOSFET GATE Drive Output. The GATE output signal uses an internal charge pump to charge the gate of an external N-channel MOSFET pass transistor. 5 M9999-070108-A Micrel, Inc. MIC2310 Pin Description (continued) Pin Number July 2008 Pin Name 22 SENSE 23 VCCSENSE 24 VCC Pin Function By connecting a very low value (mΩ) current sense resistor between these two pins, the MIC2310’s internal primary and secondary overcurrent detection circuits monitor the load current. The VCCSENSE pin is the positive (+) input terminal and the SENSE pin is the negative (-) input terminal of the overcurrent detection circuits. If the voltage across the sense resistor exceeds either the primary overcurrent threshold for a time (tPOC) or the secondary primary overcurrent threshold for any duration, the MIC2310 electronic circuit breaker is tripped, the GATE is turned OFF, the DISCH circuit is activated, and the I_FLT digital output is asserted. The controller also incorporates a patent-pending builtin test for shorted current-sense resistors. Because of this built-in self test, the MIC2310’s electronic circuit breaker cannot be disabled by connecting together the VCCSENSE and SENSE pins. Positive supply input to the MIC2310. The MIC2310 is specified to operate from +10.8V ≤ VCC ≤ +13.2V and the supply current with ENABLE = HIGH is less than 10mA. 6 M9999-070108-A Micrel, Inc. MIC2310 Absolute Maximum Ratings(1) Operating Ratings(2) VCC, VCCSENSE, SENSE, LOADSENSE, ENABLE, CSLEW, S1, S0, SOURCE..................... –0.3V to +18V GATE............................................................. –0.3V to +30V UVLO, OVP, VISS, CRETRY, CPRIMARY, HW_FLT, PWRGD, I_FLT, DISCH, GNDSENSE .... –0.3V to +6V Output Current HW_FLT, PWRGD, I_FLT pins ...................................10mA ESD Rating (All pins) Human Body Model .............................................. 2kV(3) Machine Model ......................................................200V Lead Temperature (Soldering) Pb-free package IR Reflow ..........................................+260°C +0°C/-5°C Storage Temperature..........................–65°C to +150°C Supply Voltage (VCC)................................ +10.8V to +13.2V Ambient Temperature Range (TA) ................ 0 °C to +70 °C Junction Temperature (TJ) ...................................... +125 °C Package Thermal Resistance (θJA) 24-pin TSSOP................................................83.8 °C/W DC Electrical Characteristics(4) VCC = +12V, CREG = 0.1µF, TA = +25 ºC unless otherwise noted. Bold indicates specification applies over the full operating temperature range of 0 ºC to +70 ºC. All voltages are measured with respect to AGND unless otherwise noted. Symbol Parameter VCC Operating Supply Voltage (Constant Output Power) Supply Current Internal VREG Undervoltage Lockout High Threshold Voltage Internal VREG Undervoltage Lockout Low Threshold Voltage UVLO High Threshold Voltage UVLO Low Threshold Voltage UVLO Pin Input Current OVP High Threshold Voltage OVP Low Threshold Voltage OVP Pin Input Current “Power-is-Good” GATESOURCE Threshold “Power-is-Good” High Threshold (VLOADSENSE – VGNDSENSE) ICC VVREG(UVLOH) VVREG(UVLOL) VUVLOH VUVLOL IUVLO VOVPH VOVPL IOVP VGSPGH VPGH VPGL VREG July 2008 “Power-not-Good” Low Threshold (VLOADSENSE – VGNDSENSE) VREG Output Voltage Condition Min ENABLE = LOW,HIGH VREG Low-to-High Transition Typ Max Units 10.8 13.2 V 3.95 10 4.5 mA V 4.25 V 4.25 3.70 Low-to-High Transition 0.96 1.00 1.04 V High-to-Low Transition 0.91 0.941 0.97 V 1.35 1.295 1.407 1.339 5 1.45 1.395 5 4.25 5 µA V V µA V 9.3 9.7 10.1 V 8.4 9 9.6 V 4.5 5 5.5 V UVLO = 6V Low-to-High Transition High-to-Low Transition OVP = 6V (VGATE – VSOURCE) Low-to-High Transition, (VGATE – VSOURCE) ≥ VGSPGH Measured with respect to GNDSENSE = AGND High-to-Low Transition, (VGATE – VSOURCE) ≥ VGSPGH Measured with respect to GNDSENSE = AGND RREG > 1 MΩ 7 M9999-070108-A Micrel, Inc. MIC2310 Symbol Parameter Condition Min Typ Max Units VCBP Primary OC Circuit Breaker Threshold Voltage VVCCSENSE – VSENSE VCBS Secondary OC SENSE Voltage VVCCSENSE - VSENSE 54.7 60.7 49.6 64 75 100 85 57.2 63.5 51.9 75.5 87.5 116.6 102 59.7 66.3 54.2 87 99 130 116 mV mV mV mV mV mV mV IVCCSENSE VCCSENSE Pin Input Current SENSE Pin Input Current CRETRY Pin High Threshold Voltage CRETRY Pin Low Threshold Voltage CRETRY Pin Charging Current CRETRY Pin Pull-down Current CPRIMARY Pin Low Threshold Voltage (VLOADSENSE – VGNDSENSE) = +12V (VLOADSENSE – VGNDSENSE) = +10.8V (VLOADSENSE – VGNDSENSE) = +13.2V S[1:0] = L, L Secondary OC Detector Circuit S[1:0] = L, H Breaker Trips, S[1:0] = H, L VLOADSENSE – S[1:0] = H,H VGNDSENSE = 10.8V to 13.2V VVCCSENSE = VCC 1 µA µA V ISENSE VRETRYH VRETRYL IRETRYUP IRETRYDN VPRIL VPRIL CPRIMARY Pin Low Threshold Voltage IPRI CPRIMARY Pin Charging Current VSENSE = VCC TIMER ON, VRETRY = 0V TIMER OFF, VRETRY = 1.5V During OC response; ENABLE = HIGH; VCC(SENSE) – VSENSE > VCBP Measured relative to VREG During shorted ENABLE = HIGH; CPRIMARY VCC(SENSE) – VSENSE detection; < VCBP Measured ENABLE = LOW relative to V 1.21 1.25 3 1.28 0.25 0.3 0.35 V -4.25 -3 -1.65 µA 3 mA -1.3 -1.25 -1.2 V -1.3 -1.25 -1.2 V 2.4 3 3.6 µA -4.5 -3 -1.5 mA -4.5 -3 -1.5 mA 15 V REG ∆VGATE GATE Output Voltage ∆VCP ISLEW VCSLEW – VSENSE Differential July 2008 Inrush Current slew Charging current During Primary OC Fault VCPRIMARY = VREG; ENABLE = HIGH VCC(SENSE) – VSENSE > VCBP During nominal and reset operation VPRIMARY = VREG – 1.25V; ENABLE = HIGH VCC(SENSE) – VSENSE < VCBP During disable; VCPRIMARY = VREG – 1.25V ENABLE = LOW (VGATE-VCC): VCC > 10.5V Internally clamped Charge pump to OFF VCSLEW = VCC – 50mV 8 8 50 5 10 mV 15 µA M9999-070108-A Micrel, Inc. MIC2310 Symbol Parameter Condition Min Typ Max Units IGATEUP GATE Pin Pull-up Current -60 -30 -15 µA IGATEDN Normal GATE Pin Pull-down Current Charge pump ON, VGATE = VSOURCE = +13.2V ENABLE = LOW, VGATE = 2V I_FLT Latched and OC Detector Trip or in UVLO, VGATE = 2V 1.0 2.7 4.5 mA 45 120 mA 5 V 5 V VSOURCE - VLOADSENSE 4 V VGNDSENSE 4 V VGATEFT(EXT) VSRCFT(EXT) VTHLOADSENSE VTHGNDSENSE ISOURCE Fault-mode GATE Pin Pulldown current GATE-to-AGND Fault Threshold ENABLE = LOW SOURCE-to-AGND Fault Threshold ENABLE = LOW Open LOADSENSE Threshold Open GNDSENSE Threshold SOURCE Pin Input Current ILOADSENSE LOADSENSE Pin Input Current IGNDSENSE GNDSENSE Pin Input Current Shorted RSENSE Threshold Voltage at SOURCE (VSENSE – VSOURCE) Shorted RSENSE Threshold Voltage (VVCCSENSE – VSENSE) DISCH Pin Drive Voltage DISCH Pin Drive Current Linear Sensing Range Zero Voltage VISS Output Voltage VISS DC Output Resistance ∆VDS(FET) ∆VRSENSE VDISCH IDISCH VISS(LIN) VISS(Q) RVISS VISS(SENS) ETOT July 2008 VISS Analog Signal Sensitivity VISS Total Error % (240 VA) EN = LOW, 0V ≤ SOURCE ≤ VCC EN = HIGH, SOURCE = VCC EN = HIGH, /FAULT Condition 0V ≤ SOURCE ≤ VCC +10.8V ≤ VLOADSENSE ≤ +13.2V VLOADSENSE = 0V DISCH = HIGH VGNDSENSE = 0V 18 1.5 18 µA µA µA 300 300 µA µA µA -400 VCC(SENSE) – VSENSE = 0V, VGATE – VSOURCE > VGSPGH 7 mV VSENSE – VSOURCE = 30mV, VGATE – VSOURCE > VGSPGH 12 mV IDISCH = 12mA VDISCH = 2.5V VVCC(SENSE) - VSENSE VVCC(SENSE) - VSENSE = 0mV 0 7 VVCC(SENSE) - VSENSE = 60mV 9 V µA mV mV 32 kΩ V/V ±10 % 100 [VISS(20µA) -VISS(10µA) ]/10µA ∆VVISS/∆( VVCC(SENSE) - VSENSE) 55 0.4 -400 90 103 28 30 M9999-070108-A Micrel, Inc. MIC2310 Symbol Parameter Condition ELIN VISS Analog Nonlinearity VVCC(SENSE) - VSENSE = 0mV to 90mV VOL LOW-Level Output Voltage I_FLT, PWRGD, HW_FLT LOW-Level Input Voltage ENABLE, S1, S0 HIGH-Level Input Voltage ENABLE, S1, S0 Input Pull-down Current ENABLE, S1, S0 IOUT = 1.6mA VIL VIH IIH Min Typ Max Units ±6.5 0.4 % 0.8 V V 2 VIH = +0.8V 55 V 80 120 µA Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF. 4. Specification for packaged product only. AC Electrical Characteristics(4) VCC = +12V, CREG = 0.1µF, TA = +25 ºC unless otherwise noted. Bold indicates specification applies over the full operating temperature range of 0 ºC to +70 ºC. Symbol Parameter Condition tPOR Power-on-Reset Delay tPOCSENSE Primary OC Detector Default Response Time to GATE pin Discharge tSOCSENSE Secondary OC Detector Response Time to GATE Pin Discharge Circuit Breaker Reset Delay Time ENABLE Low Pulse Width Shorted CPRIMARY Detection Time to HW_FLT Latched Shorted CPRIMARY Detection Delay after Primary OC Detection MOSFET DG Short to HW_FLT Latched VVREG ≥ VVREG(UVLOH) (VVCCSENSE -VSENSE) = 70-mV step; PRIMARY Pin Floating; and S[1:0] = H,L CGATE = 100pF (VVCCSENSE -VSENSE) = 200-mV step tCBRESET tENLPW tSCPDETECT tSCPDETPOR tDG(FET) tDS(FET) tDS-SSFAULT2 July 2008 MOSFET DS Short to HW_FLT Latched MOSFET DS Short to HW_FLT Latched Min 200 Typ Max Units 6.5 ms 300 420 µs 0.25 0.5 µs 5 µs ENABLE Low to I_FLT Low µs µs 200 ENABLE = LOW or HIGH; 0.25 VVCCSENSE -VSENSE ≤ VCBP ENABLE = LOW; GATEFT(EXT) Asserts HW_FLT ENABLE = LOW; SRCFT(EXT) Asserts HW_FLT ENABLE = HIGH-to-LOW after steady-state operation ENABLE = HIGH DISCH = LOW-to-HIGH 10 6.5 ms 10 µs 10 µs 250 µs M9999-070108-A Micrel, Inc. MIC2310 Symbol Parameter Condition tGLITCH(UVLO) UVLO & OVP Glitch Filter Delay Time VISS Propagation Delay Time Overdrive = 50mV 10 µs VVCCSENSE - VSENSE = 0mV to 60mV Capacitance from VISS to GND is 100pF VVCCSENSE - VSENSE = 0mV to 60mV Capacitance from VISS to GND is 100pF VVISS 10% to 90% Overdrive = 250mV 7 µs 25 µs 30 µs 0.25 µs tVISS(PROP) tVISS(RISE) VISS Rise Time tGLITCH(PWRGD) PWRGD Glitch Filter Delay Time GATE OFF to DISCH Delay Time tDLY(DISCH) Min Typ Max Units Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF. 4. Specification for packaged product only. July 2008 11 M9999-070108-A Micrel, Inc. MIC2310 Block Diagram July 2008 12 M9999-070108-A Micrel, Inc. MIC2310 there is sufficient charge stored on the load capacitor as evidenced by the output load voltage profile. Note that the secondary overcurrent detection threshold (ISOC) is set externally at the controller’s S[1:0] pins. Once the inrush current exceeds the ISOC threshold, the circuit breaker trips without delay and the MIC2310 controller shuts down the output. If the inrush current profile does not cause either of the OC detection circuits to trip the circuit breaker and assert the I_FLT digital output, the controller will assert the PWRGD digital output when the output load voltage is higher than the controller’s VPGH threshold voltage and the VGS of the external MOSFET is higher than the controller’s VGSPGH threshold voltage. Due to the low RDS(ON) of the external MOSFET, the output load voltage rises with the GATE voltage as the VGS of the MOSFET reaches its threshold voltage. Once the output load voltage stabilizes near the VCC supply voltage, the VGS of the external MOSFET increases above its threshold voltage and eventually exceeds VGSPGH. The PWRGD output asserts to signal that the external MOSFET is fully enhanced and ready for the application of the full load. Functional Description Basic Startup Cycle The basic operation of the MIC2310 is illustrated below in Figure 2 from a cold-start condition. With the applied VCC supply low such that the internal VREG voltage is less than the MIC2310’s internal VVREG(UVLOH) threshold voltage, all state machines are reset, all voltage and current monitor subcircuits are OFF, and the GATE drive circuit is disabled. Digital inputs and all open-drain digital outputs are inactive. When the applied VCC supply rises such that the internal VREG voltage is above the controller’s VVREG(UVLOH) threshold voltage, the tPOR counter circuit commences. Once the timer terminates, all internal state machines are activated, the CPRIMARY short detection circuit is ON and the DG & DS MOSFET short detection circuits are ON if ENABLE is LOW. The I_FLT, PWRGD, and HW_FLT outputs are valid. Upon the application of an ENABLE LOW-to-HIGH transition after the tPOR delay, or at the end of the tPOR delay if ENABLE is already HIGH, a nominal start-up commences where the dID/dt-controlled inrush current (by dID/dt = 17.6x10-3 × ISLEW / (RSENSE ×CSLEW)) is permitted to exceed the IPOC threshold for tPOC, until +12V, nominal VCC VREG = 5V, nominal VVREGUVLOH ENABLE Primary & Secondary OC Detector Armed VGSPGH VGSPGH GATE Power Good VOUT ISOC = VCBS/RSENSE set by S[1:0] Power Not Good VPGL t POC ILOAD dID/dt Control by CSLEW ∆t = f(CGATE,VTH(FET)) I SOC IPOC = VCBP/RSENSE I POC Peak inrush current = f(CSLEW, CLOAD) tPOC = f(C PRIMARY) 0A PWRGD tPOR I_FLT Figure 2. Basic Startup Cycle July 2008 13 M9999-070108-A Micrel, Inc. MIC2310 OC detector has been triggered, the 3mA current source is first disabled and a 3µA current sink is enabled to discharge the external CPRIMARY. When CPRIMARY has discharged below VPRIL, a default timer is enabled. Once the default timer (tPOCSENSE) times out, the circuit breaker is tripped, the 3µA current sink is disabled, and the 3mA current source is enabled to discharge CPRIMARY back to VREG quickly. Concurrently, the GATE drive circuit is disabled and a higher current, fault-mode pull-down current sink is enabled at the GATE pin. The DISCH output goes high to (optionally) drive external pull-down circuitry. In the event that the CPRIMARY pin is left NC (intentionally or otherwise), the overcurrent timer default value is tPOCSENSE (250µs typical), as specified in the ac specification table. Once the circuit breaker is latched, the I_FLT digital output is asserted and the PWRGD digital output becomes de-asserted when the output voltage profile falls below the controller’s VPGL threshold voltage or the VGS of the external MOSFET falls below the controller’s VGSPGH threshold voltage. Primary Overcurrent (OC) Detector Trips Circuit Breaker and Asserts I_FLT Figure 3 below illustrates the behavior of the controller to an OC event after the primary and secondary OC detection circuits have been armed (upon the application of an ENABLE LOW-to-HIGH transition and after tPOR) and steady-state operation has been achieved. Note that the assertion of the controller’s PWRGD digital output occurs when the output load voltage profile is higher than the controller’s VPGH threshold voltage and the VGS of the external MOSFET is higher than the controller’s VGSPGH threshold voltage. The use of an external CPRIMARY capacitor sets the response time, tPOC, of the primary OC detector according to the internal VPRIL threshold voltage and the CPRIMARY pin discharging current, IPRI, where tPOC = tPOCSENSE + CPRIMARY ∗ (VPRIL/IPRI). Prior to triggering the primary OC detector (i.e., when VVCCSENSE -VSENSE < VCBP), a 3mA current source is enabled to hold the CPRIMARY pin voltage to the internally-generated VREG voltage. When the primary +12V, nominal VREG = 5V, nominal VCC VVREG(UVLOH) = +4.25V Primary & Secondary OC Detectors Armed ENABLE VGSPGH VGSPGH Power Not Good GATE Power Good VOUT VPGL VCBS tPOC VCBP VVCCSENSE –VSENSE 0V PWRGD tPOR I_FLT is asserted by Primary OC Dtector CB Trip after tPOC I_FLT tPOC = f(CPRIMARY) Figure 3. Primary OC Detector Trips Circuit Breaker July 2008 14 M9999-070108-A Micrel, Inc. MIC2310 the ac specification table. When the secondary OC detector has sensed a very large current surge (VCCSENSE – VSENSE ≥ VCBS), the circuit breaker is tripped within tSOCSENSE. Concurrently, the GATE drive circuit is disabled and a higher current, fault-mode pull-down current sink is enabled at the GATE pin. The DISCH output goes high to (optionally) drive external pull-down circuitry. Once the circuit breaker is latched, the I_FLT digital output is asserted and the PWRGD digital output becomes de-asserted when the output voltage profile falls below the controller’s VPGL threshold voltage or the VGS of the external MOSFET falls below the controller’s VGSPGH threshold voltage. Secondary OC Detector Trips Circuit Breaker and Asserts I_FLT Figure 4 illustrates the behavior of the controller to an OC event after the primary and secondary OC detection circuits have been armed (upon the application of an ENABLE LOW-to-HIGH transition and after tPOR) and steady-state operation has been achieved. Note that the assertion of the controller’s PWRGD digital output occurs when the output load voltage profile is higher than the controller’s VPGH threshold voltage and the VGS of the external MOSFET is higher than the controller’s VGSPGH threshold voltage. The controller’s secondary OC detection threshold is set by the status of the controller’s S[1:0] pins and its response time is internally set at tSOCSENSE as shown in VCC = 12V, nominal VREG = 5V, nominal VVREG(UVLOH) = +4.25V Figure 4. Secondary OC Detector Trips Circuit Breaker July 2008 15 M9999-070108-A Micrel, Inc. MIC2310 voltage profile at no time rises higher than the controller’s VPGH threshold voltage and the VGS of the external MOSFET does not rise higher than the controller’s VGSPGH threshold voltage. Once the circuit breaker has latched, the I_FLT digital output is asserted. When the circuit breaker is tripped by either the primary OC or secondary OC detectors), applying a HIGH-to-LOW transition on the ENABLE pin will reset the circuit breaker. At a delay defined by tCBRESET, the internal circuit breaker is reset and is indicated when the I_FLT digital output becomes deasserted. The earliest a LOW-to-HIGH transition at ENABLE is permitted to initiate a new start-up sequence is defined by the tENLPW timing specification. Charging Load by dID/dt – Primary OC Trips CB after tPOC and CB Reset by Toggling ENABLE HIGH-to-LOW Figure 5 illustrates the behavior of the controller to an OC event after the primary and secondary OC detection circuits have been armed (upon the application of an ENABLE LOW-to-HIGH transition and after tPOR). In this example, the load capacitor is charged at a controlled dID/dt rate. Steady-state operation is not achieved as the controlled inrush profile causes the primary OC detector to trigger at IPOC and continues charging when the tPOCSENSE timer terminates. Note that the controller’s PWRGD digital output does not assert because the output load VCC = 12V, nominal VREG = 5V, nominal VVREG(UVLOH) = +4.25V Figure 5. dID/dt Load Charge Profile w/ Primary OC Circuit Breaker (CB) Trip w/ CB Reset July 2008 16 M9999-070108-A Micrel, Inc. MIC2310 The use of an external CRETRY capacitor sets the autoretry time, tRETRY, according to the internal VRETRYH threshold voltage and the CRETRY pin charging current, IRETRYUP [tRETRY = CRETRY * (VRETRYH/IRETRYUP)]. Prior to the tripping of the OC circuit breaker, a 3mA current sink is enabled holding the CRETRY pin voltage at 0V. When the OC circuit breaker has been tripped, the 3mA current sink is disabled and a 3µA current source is enabled to charge the external CRETRY capacitor. When CRETRY has charged above VRETRYH, the circuit breaker is reset such that the I_FLT digital output is de-asserted. Additionally, the 3µA current source is disabled and the 3mA current sink is enabled to discharge the CRETRY pin voltage back to 0V. When CRETRY has discharged below VRETRYL, the GATE drive circuit is re-enabled and the DISCH output returns low. For the case of a persistent overcurrent load, the controller will continuously cycle between starting up into an OC condition that trips the circuit breaker and the auto-retry time before the circuit breaker is reset. Primary OC Trips Circuit Breaker (CB) and CB Resets with CRETRY (Auto-Retry Timing Capacitor) Figure 6 illustrates the behavior of the controller to a primary OC event when a CRETRY capacitor is used to automatically reset the circuit breaker. The automatic reset operation is the same for the case of a secondary OC event. In this example, the primary and secondary OC detection circuits have been armed (upon the application of an ENABLE LOW-to-HIGH transition and after tPOR) and the load capacitor is charged at a controlled dID/dt rate. Note that in this diagram, ENABLE is tied to VCC and rises with VCC. Steady-state operation is achieved as the controller’s PWRGD digital output is asserted when the output load voltage profile is higher than the controller’s VPGH threshold voltage and the VGS of the external MOSFET is higher than the controller’s VGSPGH threshold voltage. When the primary OC detector has been triggered by an output current exceeding IPOC for a time tPOC, the circuit breaker is tripped, the GATE drive circuit is disabled, the fault-mode pull-down current sink is enabled at the GATE pin, the DISCH output goes high, and the I_FLT digital output becomes asserted. July 2008 17 M9999-070108-A Micrel, Inc. MIC2310 VCC = 12V, nominal VREG = 5V, nominal VCC & VREG VVREG(UVLOH) ENABLE VGSPGH VGSPGH GATE VPGL VPGH VOUT tPOC IPOC ILOAD tRETRY CRETRY tPOR PWRGD I_FLT DISCH Figure 6. Primary Overcurrent Fault with Auto-Retry to Reset the Circuit Breaker current sink is not capable of holding the voltage at 0V as the GATE voltage tracks the MOSFET’s DRAIN voltage. The voltage monitor circuit at the controller’s GATE pin will be triggered once the GATE voltage crosses the VGATEFT(EXT) threshold voltage. The HW_FLT digital output is subsequently asserted within a delay approximately equal to the delay in the logic circuits – no additional timing circuit is required. To clear the latched GATE voltage monitor circuit and to reset the HW_FLT digital output, the applied VCC supply voltage must fall such that VREG is below the controller’s VVREG(UVLOL) threshold voltage. HW_FLT Digital Output Asserted by a MOSFET DG Short with ENABLE = LOW In order to protect the system from the result of the installation of a damaged MOSFET on the PCB, the controller incorporates a MOSFET shorted DG detection scheme whose operation is described in Figure 7. With the applied VCC supply high such that the internal VREG voltage is above the controller’s VVREG(UVLOH) threshold voltage, an elapsed POR timer, and with the ENABLE input LOW, a weak current sink at the GATE pin attempts to hold the GATE voltage at 0V. If there is a DG short on the MOSFET, the weak July 2008 18 M9999-070108-A Micrel, Inc. MIC2310 Figure 7. Hardware Fault Detection of a MOSFET DG Short with ENABLE = LOW July 2008 19 M9999-070108-A Micrel, Inc. MIC2310 at 0V as the SOURCE voltage tracks the MOSFET’s DRAIN voltage. The voltage monitor circuit at the controller’s SOURCE pin will be triggered once the SOURCE voltage crosses the VSRCFT(EXT) threshold voltage. The HW_FLT digital output is subsequently asserted within a delay approximately equal to the delay in the logic circuits – no additional timing circuit is required. To clear the latched source voltage monitor circuit and to reset the HW_FLT digital output, the applied VCC supply voltage must fall such that VREG is below the controller’s VVREG(UVLOL) threshold voltage. HW_FLT Digital Output Asserted by MOSFET DS Short with ENABLE = LOW In order to protect the system from the result of the installation of a damaged MOSFET on the PCB, the controller incorporates a MOSFET shorted DS detection scheme whose operation is described in Figure 8. With the applied VCC supply high such that the internal VREG voltage is above the controller’s VVREG(UVLOH) threshold voltage, an elapsed POR timer, and with the ENABLE input LOW, a voltage monitor circuit for the controller’s SOURCE pin is enabled. If there is a DS short on the MOSFET, the external load on the MOSFET is not capable of holding the voltage Figure 8. Hardware Fault Detection of a MOSFET DS Short with ENABLE = LOW July 2008 20 M9999-070108-A Micrel, Inc. MIC2310 current sink is enabled, the DISCH output goes high, and the tDS-SSFAULT timer is started. With the ENABLE input LOW, a voltage monitor circuit for the controller’s SOURCE pin (i.e., VOUT) is enabled. If there is a DS short, the voltage at the source will not drop to 0V even though the GATE is OFF. If the output voltage at the SOURCE pin remains higher than the controller’s VSRCFT(EXT) threshold voltage when the tDS-SSFAULT timer terminates, the HW_FLT digital output is asserted. To repair the damaged MOSFET and to reset the HW_FLT digital output and the controller, the service processor instructs the main supply to turn off the VCC supply voltage to the controller such that VREG falls below the controller’s VVREG(UVLOL) threshold voltage. HW_FLT Asserted by MOSFET DS Short after Steady-state Operation then ENABLE = HIGH-toLOW Figure 9 illustrates the behavior of the controller to a shorted DS MOSFET condition after steady-state operation is achieved via a nominal start-up. Note that the load capacitor at start-up was charged in a controlled dID/dt mode and assertion of the controller’s PWRGD digital output occurs when the output load voltage profile is higher than the controller’s VPGH threshold voltage and the VGS of the external MOSFET is higher than the controller’s VGSPGH threshold voltage. Upon the application of a HIGH-toLOW transition on ENABLE by the service processor, the GATE drive circuit is disabled, the weak GATE Figure 9. Hardware Fault by a MOSFET DS Short after Steady-State Operation (ENABLE = HIGH-to-LOW) July 2008 21 M9999-070108-A Micrel, Inc. MIC2310 voltage monitor circuit for the controller’s SOURCE pin is also enabled. If there is a DS short, the voltage at the source will not drop to 0V even though the GATE is OFF. If the output voltage at the SOURCE pin remains higher than the controller’s VSRCFT(EXT) threshold voltage when the tDS-SSFAULT timer terminates, the HW_FLT digital output is asserted. To repair the damaged MOSFET and to reset the HW_FLT digital output and the controller, the service processor instructs the main supply to turn off the VCC supply voltage to the controller such that VREG falls below the controller’s VVREG(UVLOL) threshold voltage. HW_FLT Asserted by MOSFET DS Short after Steady-state Operation then a Fault Condition Figure 10 illustrates the behavior of the controller to a shorted DS MOSFET condition after steady-state operation is achieved via a nominal start-up. With the occurrence of one of the following fault conditions – UVLO, OVP, primary OC, secondary OC, open LOADSENSE, or open GNDSENSE - the GATE drive circuit is disabled, the GATE fault-mode pull-down current sink is enabled, the DISCH output goes high, and the tDS-SSFAULT timer is started. The occurrence of a primary OC fault condition is shown here. The VCC & VREG VVREG(UVLOH) VVREG(UVLOL) VVREG(UVLOH) ENABLE VGSPGH VGSPGH GATE DG Short VPGL VPGH VOUT VSRCFT(EXT) tPOC ILOAD tPOR tPOR PWRGD I_FLT tDS-SSFAULT HW_FLT DISCH Figure 10. HW_FLT Asserted by a MOSFET DS Short after Steady-State Operation then a Fault Condition July 2008 22 M9999-070108-A Micrel, Inc. MIC2310 RSENSE short detection at low current, a minimum VDS of ∆VDS(FET) must exist across the external MOSFET for a shorted sense resistor to be detected. For larger values of VDS across the external MOSFET generated by higher load currents, the ∆VRSENSE threshold voltage for the detection of an RSENSE short follows the equation ∆VRSENSE = 0.5 * (VDS - ∆VDS(FET)). If there exists a short across the sense resistor such that VRS drops below the ∆VRSENSE threshold voltage, then an internal circuit breaker is tripped, the GATE drive circuit is disabled, the GATE fault-mode pull-down current sink is enabled, the DISCH output goes high, and the HW_FLT digital output is asserted. To repair the damaged sense resistor and reset the HW_FLT digital output, the service processor instructs the main supply to turn off the VCC supply voltage to the controller such that VREG falls below the controller’s VVREG(UVLOL) threshold voltage. Shorted RSENSE Detector Trips CB and Asserts HW_FLT In order to protect the system from the result of the installation of a shorted sense resistor on the PCB, which would increase the effective OC detection thresholds to unsafe levels, the controller incorporates a shorted RSENSE detection scheme whose operation is described in Figure 11. The RSENSE detection circuitry is enabled upon the application of an ENABLE LOWto-HIGH transition, an elapsed POR timer, and the VGS of the external MOSFET being higher than the controller’s VGSPGH threshold voltage. Note that for the case of a shorted sense resistor, dID/dt control of the inrush current is disabled and the controller defaults to dVGATE/dt control of the GATE voltage. An RSENSE short is detected by comparing the VRS voltage drop across the sense resistor (VCCSENSE-VSENSE) to the VDS voltage drop across the external MOSFET (VSENSE-VSOURCE). To avoid a false July 2008 23 M9999-070108-A Micrel, Inc. MIC2310 VCC & VREG VVREG(UVLOH) VVREG(UVLOL) VVREG(UVLOH) ENABLE VGSPGH GATE VPGH VOUT VDS(FET) DS(FET) RSENSE VRS tPOR tPOR PWRGD HW_FLT DISCH Figure 11. Shorted RSENSE Trips Circuit Breaker and Asserts HW_FLT July 2008 24 M9999-070108-A Micrel, Inc. MIC2310 capacitor value, one which keeps the primary OC response time, tPOC, less than 0.5s, CPRIMARY charges above VPRIH before the POR timer terminates and normal operation commences. However, if the CPRIMARY pin is shorted to GND or CPRIMARY is too large, as in this timing diagram, the POR timer terminates before CPRIMARY charges above VPRIH and a shorted CPRIMARY is detected. When a CPRIMARY short is detected, the GATE drive circuit and the DISCH output are not affected, however, the HW_FLT digital output is asserted. To repair the damaged CPRIMARY capacitor and reset the HW_FLT digital output, the service processor instructs the main supply to turn off the VCC supply voltage to the controller such that VREG falls below the controller’s VVREG(UVLOL) threshold voltage. Shorted CPRIMARY Detector Asserts HW_FLT at Start-up In order to protect the system from the result of the installation of a shorted or excessively large CPRIMARY capacitor on the PCB, the controller incorporates a shorted CPRIMARY detection scheme. A shorted CPRIMARY pin or an excessively large CPRIMARY capacitor will impact the primary OC detection time, tPOC. The operation of the shorted CPRIMARY detection scheme at start-up is described in Figure 12. Prior to power-up, the CPRIMARY pin is discharged to 0V. As the applied VCC supply and the internal VREG voltage rise, a 3mA current source is applied to the CPRIMARY pin to charge CPRIMARY to VREG. When the internal VREG voltage is above the controller’s VVREG(UVLOH) threshold voltage, the tPOR timer is initiated. For the case of a reasonable CPRIMARY VCC & VREG VVREG(UVLOH) VVREG(UVLOH) VVREG(UVLOL) ENABLE VGSPGH VGSPGH GATE VPGH VPGL VOUT ILOAD SMALLER CPRIMARY CPRIMARY VPRIH VPRIH CPRIMARY TOO LARGE tPOR tPOR PWRGD HW_FLT DISCH Figure 12. Shorted CPRIMARY Detector Asserts HW_FLT at Start-up July 2008 25 M9999-070108-A Micrel, Inc. MIC2310 circuit remains enabled and the DISCH output remains low such that the external MOSFET remains ON, however, the HW_FLT digital output is asserted. To repair the damaged CPRIMARY capacitor and reset the HW_FLT digital output, the service processor instructs the main supply to turn off the VCC supply voltage to the controller such that VREG falls below the controller’s VVREG(UVLOL) threshold voltage. Shorted CPRIMARY Detector Asserts HW_FLT during Steady-state Figure 13 illustrates the behavior of the controller to a shorted CPRIMARY capacitor condition after steady-state operation is achieved via a nominal start-up. If a CPRIMARY short occurs during steady-state operation, the CPRIMARY pin voltage will drop below the VPRIL threshold voltage and a shorted CPRIMARY is detected. When a CPRIMARY short is detected, the GATE drive VCC & VREG VVREG(UVLOH) VVREG(UVLOH) VVREG(UVLOL) ENABLE VGSPGH VGSPGH GATE VPGH VPGL VOUT ILOAD SHORTED CPRIMARY CPRIMARY VPRIH CPRIMARY REPAIRED VPRIH VPRIL tPOR tPOR PWRGD HW_FLT DISCH Figure 13. Shorted CPRIMARY Detector Asserts HW_FLT During Steady-State July 2008 26 M9999-070108-A Micrel, Inc. MIC2310 when the CPRIMARY short detection circuitry is reenabled. In the timing diagram, CPRIMARY becomes shorted during the primary OC event. When the CPRIMARY pin voltage falls below VPRIL, the tPOCSENSE timer is enabled. Once this timer times out, the circuit breaker is tripped, I_FLT is asserted, the GATE drive circuitry is disabled, the GATE fault-mode pull-down current sink is enabled, and the DISCH output goes high. As the external MOSFET is turned OFF, the output current drops and an overcurrent condition is no longer detected. This initiates the tSCPDETPOR timer. Since CPRIMARY does not charge back up above VPRIH before this timer expires, HW_FLT is asserted after the tSCPDETPOR time. To repair the damaged CPRIMARY capacitor and reset the HW_FLT digital output, the service processor instructs the main supply to turn off the VCC supply voltage to the controller such that VREG falls below the controller’s VVREG(UVLOL) threshold voltage. Shorted CPRIMARY Detector Asserts HW_FLT After Primary OC Event The diagram in Figure 14 illustrates the behavior of the controller to a shorted CPRIMARY capacitor condition after steady-state operation is achieved via a nominal start-up and after a primary OC event has occurred. As described previously, during a primary OC event, the CPRIMARY capacitor is discharged as part of setting the primary OC detector response time, tPOC. In order to prevent a false CPRIMARY short detection from occurring while the CPRIMARY pin is being intentionally discharged, the CPRIMARY short detection circuit is disabled when the primary OC detector detects an overcurrent. In addition, the CPRIMARY short detection circuit is not re-enabled until after a time delay, tSCPDETPOR, once the primary OC detector no longer detects an overcurrent. This delay time should allow a capacitor of reasonable size to be charged back up above VPRIH, even if it has been discharged to 0V, such that a false CPRIMARY short is not indicated July 2008 27 M9999-070108-A Micrel, Inc. MIC2310 VCC & VREG VVREG(UVLOH) VVREG(UVLOH) VVREG(UVLOL) ENABLE VGSPGH VGSPGH GATE VPGH VOUT tPOCSENSE tPOC IPOC ILOAD SHORTED CPRIMARY CPRIMARY REPAIRED VPRIH CPRIMARY VPRIH VPRIL tPOR tSCPDETPOR tPOR PWRGD I_FLT HW_FLT DISCH Figure 14. Shorted CPRIMARY Detector Asserts HW_FLT after Primary OC Event July 2008 28 M9999-070108-A Micrel, Inc. MIC2310 LOADSENSE pin is open, the LOADSENSE voltage will remain at a lower voltage due to the load of other internal circuitry. An open LOADSENSE pin is detected by comparing the voltage at the SOURCE pin to the voltage at the LOADSENSE pin. Once the voltage at the SOURCE pin differs from the voltage at the LOADSENSE pin by VTHLOADSENSE, a circuit breaker is tripped, the GATE drive circuitry is disabled, the GATE fault-mode pull-down current sink is enabled, and the DISCH output goes high. This circuit breaker can be reset, such that the GATE drive circuitry can be re-enabled, by either a HIGH-to-LOW transition on ENABLE or turning off the VCC supply voltage to the controller such that VREG falls below the controller’s VVREG(UVLOL) threshold voltage. Open LOADSENSE Detector Trips CB In order to protect the system from the result of an open LOADSENSE pin, the controller incorporates an open LOADSENSE detection scheme. An open LOADSENSE pin could result in the effective primary OC detection threshold being at an unsafe level. The timing diagram in Figure 15 describes the operation of this function. With the applied VCC supply high such that the internal VREG voltage is above the controller’s VVREG(UVLOH) threshold voltage, an elapsed POR timer, and with the application of an ENABLE LOW-to-HIGH transition, the GATE drive circuitry is enabled and the GATE voltage begins to rise. As the external MOSFET turns ON, the SOURCE voltage begins to rise also. Normally, the LOADSENSE voltage would rise with the SOURCE voltage. However, if the VCC & VREG VVREG(UVLOH) VVREG(UVLOL) VVREG(UVLOH) ENABLE VGSPGH GATE VPGH VTHLOADSENSE VOUT ILOAD LOADSENSE CONNECTED LOADSENSE OPEN LOADSENSE tPOR tPOR PWRGD DISCH Figure 15. Open LOADSENSE Detector Trips CB July 2008 29 M9999-070108-A Micrel, Inc. MIC2310 would remain at 0V. However, if the GNDSENSE pin is open, the GNDSENSE voltage will rise due to the load of other internal circuitry. An open GNDSENSE pin is detected by comparing the voltage at the GNDSENSE pin to the voltage at the AGND pin. Once the voltage at the GNDSENSE pin differs from the voltage at the AGND pin by VTHGNDSENSE, a circuit breaker is tripped, the GATE drive circuitry is disabled, the GATE fault-mode pull-down current sink is enabled, and the DISCH output goes high. This circuit breaker can be reset, such that the GATE drive circuitry can be re-enabled, by either a HIGH-to-LOW transition on ENABLE or turning off the VCC supply voltage to the controller such that VREG falls below the controller’s VVREG(UVLOL) threshold voltage. Open GNDSENSE Detector Trips CB In order to protect the system from the result of an open GNDSENSE pin, the controller incorporates an open GNDSENSE detection scheme. An open GNDSENSE pin could result in the effective primary OC detection threshold being at an unsafe level. The timing diagram in Figure 16 describes the operation of this function. With the applied VCC supply high such that the internal VREG voltage is above the controller’s VVREG(UVLOH) threshold voltage, an elapsed POR timer, and with the application of an ENABLE LOW-to-HIGH transition, the GATE drive circuitry is enabled and the GATE voltage begins to rise. As the external MOSFET turns ON, the SOURCE voltage begins to rise also and the LOADSENSE voltage follows the SOURCE voltage. Normally, the GNDSENSE pin VCC & VREG VVREG(UVLOH) VVREG(UVLOL) VVREG(UVLOH) ENABLE VGSPGH GATE VPGH VOUT ILOAD GNDSENSE OPEN VTHGNDSENSE GNDSENSE GNDSENSE CONNECTED tPOR tPOR PWRGD DISCH Figure 16. Open GNDSENSE Detector Trips CB July 2008 30 M9999-070108-A Micrel, Inc. MIC2310 VOVPH threshold voltage, the GATE drive circuitry is disabled, the GATE fault-mode pull-down current sink is enabled, and the DISCH output goes high. Increasing VCC such that the voltage applied to the UVLO pin increases above VUVLOH or decreasing VCC such that the voltage applied to the OVP decreases below VOVPL re-enables the GATE drive circuit and forces the DISCH output low, allowing the controller to return to normal operation. UVLO and OVP Operation The system can be protected against an undervoltage condition or an over-voltage condition on the VCC supply by using an external resistor divider and the UVLO and OVP pins, respectively. Figure 17 illustrates the timing of the GATE and digital pin outputs when the input supply crosses the UVLO and OVP thresholds. When the voltage applied to the UVLO pin is less than the VUVLOL threshold voltage or the voltage applied to the OVP pin is greater than the VCC & VREG VVREG(UVLOH) ENABLE VGSPGH VGSPGH VGSPGH GATE VPGL VPGH VPGH VPGL VPGH VOUT ILOAD UVLOL UVLO UVLOH OVPH OVPL OVP tPOR PWRGD DISCH Figure 17. UVLO and OVP Operation July 2008 31 M9999-070108-A Micrel, Inc. MIC2310 digital output is asserted and the VISS output becomes active. The current flowing in the external sense resistor is determined by sensing the voltage across the sense resistor (VCCSENSE-VSENSE). As the output current varies under changing load conditions, VCCSENSE-VSENSE also varies and the VISS output voltage changes proportionally according to VISS(SENS). When the external MOSFET is disabled, either by a HIGH-to-LOW transition on ENABLE or due to a fault condition, the VGS of the external MOSFET falls below the controller’s VGSPGH threshold voltage. This causes the PWRGD digital output to be de-asserted and the VISS output to be disabled. VISS Output Operation The VISS output provides a voltage which is proportional to the output current flowing in the external sense resistor. Figure 18 illustrates the operation of this output. With the applied VCC supply high such that the internal VREG voltage is above the controller’s VVREG(UVLOH) threshold voltage, an elapsed POR timer, and with the application of an ENABLE LOW-to-HIGH transition, the GATE drive circuitry is enabled. When the output load voltage profile is higher than the controller’s VPGH threshold voltage and the VGS of the external MOSFET is higher than the controller’s VGSPGH threshold voltage, the PWRGD VCC & VREG VVREG(UVLOH) VVREG(UVLOL) ENABLE VGSPGH VGSPGH GATE VPGH VPGL VOUT ILOAD VISS tPOR PWRGD DISCH Figure 18. VISS Operation July 2008 32 M9999-070108-A Micrel, Inc. MIC2310 components are vital with regards to the shorted RSENSE detection scheme such that the values of each need to be chosen such that variations in RDS(ON) and RSENSE over process, supply, and temperature does not result in a false RSENSE short detection. In short, the value of RDS(ON) of the external MOSFET should be selected to not exceed twice the value of RSENSE over process, supply, and temperature, to avoid the generation of a false RSENSE short detection. Applications Information The MIC2310 can be configured to address powerlimiting applications other than the 240-VA power control (UL60950 Safe Power Handling Systems). There are two key requirements to consider in selecting the external components for use in various power-limit applications: 1) The value (and tolerance) of the RSENSE current sensing resistor; and 2) The RDS(ON) of the external Power MOSFET. These two July 2008 33 M9999-070108-A Micrel, Inc. MIC2310 Package Information 24-Pin TSSOP (TS) MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2008 Micrel, Incorporated. July 2008 34 M9999-070108-A