TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 D Complete PCM Codec and Filtering Systems Include: – Transmit High-Pass and Low-Pass Filtering – Receive Low-Pass Filter With (sin x)/x Correction – Active RC Noise Filters – µ-Law or A-Law Compatible Coder and Decoder – Internal Precision Voltage Reference – Serial I/O Interface – Internal Autozero Circuitry D D D D D D D D D µ-Law – TP13064B and TP3064B A-Law – TP13067B and TP3067B ±5 -V Operation Low Operating Power . . . 70 mW Typ Power-Down Standby Mode . . . 3 mW Typ Automatic Power Down TTL- or CMOS-Compatible Digital Interface Maximizes Line Interface Card Circuit Density Improved Versions of National Semiconductor TP3064, TP3067, TP3064-X, and TP3067-X description The TP3064B, TP3067B, TP13064B, and TP13067B each comprise a single-chip pulsecode-modulation encoder and decoder (PCM codec), and PCM line filter. They also provide band-pass filtering of the analog signals prior to the encoding, and low-pass filtering after the decoding of voice signals and call-progress tones. All the functions required to interface a full-duplex (2-wire) voice telephone circuit with a time-division-multiplexed (TDM) system are included on-chip. These devices are pin-for-pin compatible with the National Semiconductor TP3064 and TP3067. Primary applications include: • • • • • DW OR N PACKAGE (TOP VIEW) VPO+ ANLG GND VPO – VPI VFRO VCC FSR DR BCLKR/CLKSEL MCLKR/PDN 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VBB VFXI+ VFXI – GSX ANLG LOOP TSX FSX DX BCLKX MCLKX Line interface for digital transmission and switching of T1 carrier, PABX (private automated branch exchange), and central office telephone systems Subscriber line concentrators Digital-encryption systems Digital voice-band data-storage systems Digital signal processing These devices are designed to perform the transmit encoding (A/D conversion) and receive decoding (D/A conversion) as well as the transmit and receive filtering functions in a PCM system, and are intended to be used at the analog termination of a PCM line or trunk. They require a transmit master clock and a receive master clock that may be asynchronous (1.536 MHz, 1.544 MHz, or 2.048 MHz), transmit and receive data clocks that are synchronous with the master clock (but can vary from 64 kHz to 2.048 MHz), and transmit and receive frame-sync pulses. The TP3064B and TP13064B contain patented circuitry to achieve low transmit channel idle noise and are not recommended for applications in which the composite signals on the transmit side are below – 55 dBm0. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the CMOS gates. Copyright 1996, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 The TP3064B and TP3067B are characterized for operation from 0°C to 70°C. The TP13064B and TP13067B are characterized for operation from – 40°C to 85°C. functional block diagram R2 17 Analog Input VFXI – VFXI + 18 R1 19 ANLG LOOP Autozero Logic – + RC Active Filter R VPO+ GSX 16 SwitchedCapacitor Band-Pass Filter S/H DAC – 1 + R VPO – Transmit Regulator 13 DX OE Comparator – 3 A/D Control Logic Voltage Reference + RC Active Filter R3 4 VPI SwitchedCapacitor Low-Pass Filter Receive Regulator S/H DAC 8 DR CLK R4 5 VFRO 15 Timing and Control 5V 6 VCC 2 TSX –5 V 20 VBB 11 2 ANLG GND POST OFFICE BOX 655303 MCLKX 10 MCLKR/ PDN • DALLAS, TEXAS 75265 12 9 7 14 BCLKX BCLKR/ FSR FSX CLKSEL TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 Terminal Functions TERMINAL NAME DESCRIPTION NO. ANLG GND 2 ANLG LOOP 16 Analog loopback control input. Must be set to logic low for normal operation. When pulled to logic high, the transmit filter input is disconnected from the output of the transmit preamplifier and connected to the VPO+ output of the receive power amplifier. 9 The bit clock that shifts data into DR after the FSR leading edge. May vary from 64 kHz to 2.048 MHz. Alternately, can be a logic input that selects either 1.536 MHz/1.544 MHz or 2.048 MHz for master clock in synchronous mode. BCLKX is used for both transmit and receive directions (see Table 1). 12 The bit clock that shifts out the PCM data on DX. May vary from 64 kHz to 2.048 MHz, but must be synchronous with MCLKX BCLKR/CLKSEL BCLKX DR 8 DX 13 Analog ground. All signals are referenced to ANLG GND. Receive data input. PCM data is shifted into DR following the FSR leading edge. The 3-state PCM data output that is enabled by FSX FSR 7 Receive frame-sync pulse input that enables BCLKR to shift PCM data in DR. FSR is an 8-kHz pulse train (see Figures 1 and 2 for timing details). FSX 14 Transmit frame-sync pulse that enables BCLKX to shift out the PCM data on DX. FSX is an 8-kHz pulse train (see Figures 1 and 2 for timing details). GSX 17 Analog output of the transmit input amplifier. GSX is used to externally set gain. MCLKR/PDN 10 Receive master clock (must be 1.536 MHz, 1.544 MHz, or 2.048 MHz). May be synchronous with MCLKX, but should be synchronous for best performance. When MCLKR is connected continuously low, MCLKX is selected for all internal timing. When MCLKR is connected continuously high, the device is powered down. MCLKX 11 Transmit master clock (must be 1.536 MHz, 1.544 MHz, or 2.048 MHz). May be asynchronous with MCLKR TSX 15 Open-drain output that pulses low during the encoder time slot VBB VCC 20 Negative power supply. VBB = – 5 V ± 5% 6 Positive power supply. VCC = 5 V ± 5% VFRO 5 Analog output of the receive filter VFXI+ 19 Noninverting input of the transmit input amplifier VFXI – 18 Inverting input of the transmit input amplifier VPI 4 Inverting input to the receive power amplifier. Also powers down both amplifiers when connected to VBB. VPO+ 1 The noninverted output of the receive power amplifier VPO – 3 The inverted output of the receive power amplifier POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Supply voltage, VBB (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 7 V Voltage range at any analog input or output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC + 0.3 V to VBB – 0.3 V Voltage range at any digital input or output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC + 0.3 V to GND – 0.3 V Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range: TP3064B, TP3067B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C TP13064B, TP13067B . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: DW or N package . . . . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltages are with respect to GND. DISSIPATION RATING TABLE PACKAGE TA ≤ 25°C POWER RATING DERATING FACTOR ABOVE TA = 25°C TA = 70°C POWER RATING TA = 85°C POWER RATING DW 1025 mW 8.2 mW/°C 656 mW 533 mW N 1150 mW 9.2 mW/°C 736 mW 598 mW recommended operating conditions (see Note 2) MIN NOM MAX UNIT Supply voltage, VCC 4.75 5 5.25 V Supply voltage, VBB – 4.75 –5 – 5.25 V High-level input voltage, VIH 2.2 Low-level input voltage, VIL Common-mode input voltage range, VICR† Load resistance at GSX, RL V 0.6 V ± 2.5 V 10 Load capacitance at GSX, CL kΩ 50 TP3064B, TP3067B Operating free-air free air temperature, temperature TA TP13064B, TP13067B 0 70 – 40 85 pF °C † Measure with CMRR > 60 dB. NOTE 2: To avoid possible damage to these CMOS devices and resulting reliability problems, the power-up procedure described in the device power-up sequence paragraphs later in this document should be followed. 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 electrical characteristics over power supply variations and recommended free-air temperature range (unless otherwise noted) supply current PARAMETER ICC Supply current from VCC IBB Supply current from VBB TEST CONDITIONS Power down TP306xB MIN TYP† MAX TP1306xB MIN TYP† MAX 0.5 1 0.5 1.2 6 10 6 11 0.5 1 0.5 1.2 6 10 6 11 No load Active Power down No load Active UNIT mA mA † All typical values are at VCC = 5 V, VBB = – 5 V, and TA = 25°C. electrical characteristics at VCC = 5 V ± 5%, VBB = –5 V ± 5%, GND at 0 V, TA = 25°C (unless otherwise noted) digital interface PARAMETER VOH TEST CONDITIONS High-level output voltage DX MIN IH = – 3.2 mA IL = 3.2 mA DX VOL Low level output voltage Low-level IIH IIL High-level input current Low-level input current All digital inputs IOZ Output current in high-impedance state DX TSX MAX 2.4 V 0.4 IL = 3.2 mA, Drain open VI = VIH to VCC 0.4 VI = GND to VIL VO = GND to VCC UNIT V ± 10 µA ± 10 µA ± 10 µA MAX UNIT ± 200 nA analog interface with transmit amplifier input PARAMETER TEST CONDITIONS II ri Input current VFXI+ or VFXI– Input resistance VFXI+ or VFXI– ro Output resistance VI = – 2.5 V to 2.5 V VI = – 2.5 V to 2.5 V Closed loop, Output dynamic range GSX AV BI Open-loop voltage amplification VFXI+ to GSX Unity-gain bandwidth GSX VIO CMRR Input offset voltage VFXI+ or VFXI– MIN TYP† 10 Unit gain MΩ 1 RL ≥ 10 kΩ 3 Ω ± 2.8 V 5000 1 2 MHz ± 20 Common-mode rejection ratio kSVR Supply-voltage rejection ratio † All typical values are at VCC = 5 V, VBB = – 5 V, and TA = 25°C. mV 60 dB 60 dB analog interface with receive filter TYP† MAX 1 3 Ω VFRO to GND 500 pF Output dc offset voltage VFRO to GND † All typical values are at VCC = 5 V, VBB = – 5 V, and TA = 25°C. ± 200 mV PARAMETER Output resistance TEST CONDITIONS VFRO VFRO = ± 2.5 V Load resistance Load capacitance MIN POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 UNIT Ω 600 5 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 analog interface with power amplifiers PARAMETER TEST CONDITIONS II ri Input current VPI = – 1 V to 1 V Input resistance VPI = – 1 V to 1 V ro Output resistance VPO + or VPO – Inverting unity gain AV BI Voltage amplification VPO – or VPO + VPO – = 1.77 Vrms, Unity-gain bandwidth VPO – Open loop VIO Input offset voltage TYP† MAX ± 100 10 RL = 600 Ω –1 kHz ± 25 0 kHz to 4 kHz 60 4 kHz to 50 kHz 36 VPO – connected to VPI RL Load resistance Connected from VPO+ to VPO – CL Load capacitance † All typical values are at VCC = 5 V, VBB = – 5 V, and TA = 25°C. POST OFFICE BOX 655303 mV dB Ω 600 100 • DALLAS, TEXAS 75265 nA Ω 400 Supply voltage rejection ratio of VCC or VBB Supply-voltage UNIT MΩ 1 kSVR 6 MIN pF TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 timing requirements PARAMETER TEST CONDITIONS MIN TYP† MAX fclock(M) Frequency of master clock fclock(B) Frequency of bit clock, transmit BCLKX tr1 Rise time of master clock MCLKX and MCLKR Measured from 20% to 80% 50 ns tf1 Fall time of master clock MCLKX and MCLKR Measured from 20% to 80% 50 ns tr2 tf2 Rise time of bit clock, transmit BCLKX Measured from 20% to 80% 50 ns Fall time of bit clock, transmit BCLKX Measured from 20% to 80% 50 ns tw1 tw2 Pulse duration, MCLKX and MCLKR high 160 ns Pulse duration, MCLKX and MCLKR low 160 ns 100 ns 160 ns tsu1 tw3 tw4 Depends on the device used and BCLKX/CLKSEL 64 Setup time, BCLKX high (and FSX in long-frame sync mode) before MCLKX↓ First bit clock after the leading edge of FSX Pulse duration, BCLKX and BCLKR high VIH = 2.2 V VIL = 0.6 V MHz 2.048 MHz 160 ns th1 Hold time, frame sync low after bit clock low (long frame only) 0 ns th2 Hold time, BCLKX high after frame sync↑ (short frame only) 0 ns tsu2 Setup time, frame sync high before bit clock↓ (long frame only) 80 ns td1 td2 Pulse duration, BCLKX and BCLKR low 1.536 1.544 2.048 UNIT MCLX and MCLKR Delay time, BCLKX high to data valid Load = 150 pF plus 2 LSTTL loads‡ Delay time, BCLKX high to TSX low Load = 150 pF plus 2 LSTTL loads‡ td3 Delay time, BCLKX (or 8 clock FSX in long frame only) low to data output disabled td4 Delay time, FSX or BCLKX high to data valid (long frame only) tsu3 th3 CL = 0 pF to 150 pF Setup time, DR valid before BCLKR↓ Hold time, DR valid after BCLKR or BCLKX↓ 0 140 ns 140 ns 50 165 ns 20 165 ns 50 ns 50 ns tsu4 Setup time, FSR or FSX high before BCLKR or BCLKX↓ Short-frame sync pulse (1- or 2-bit clock periods long) (see Note 3) 50 ns th4 Hold time, FSX or FSR high after BCLKX or BCLKR↓ Short-frame sync pulse (1- or 2-bit clock periods long) (see Note 3) 100 ns th5 Hold time, frame sync high after bit clock↓ Long-frame sync pulse (from 3- to 8-bit clock periods long) 100 ns tw5 Pulse duration of the frame sync pulse (low level) 64 kbps operating mode 160 † All typical values are at VCC = 5 V, VBB = – 5 V, and TA = 25°C. ‡ Nominal input value for an LSTTL load is 18 kΩ. NOTE 3: For short-frame sync timing, FSR and FSX must go high while their respective bit clocks are high. ns POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 operating characteristics over operating free-air temperature range, VCC = 5 V ± 5%, VBB = –5 V ± 5%, GND at 0 V, VI = 1.2276 V, f = 1.02 kHz, transmit input amplifier connected for unity gain, noninverting (unless otherwise noted) filter gains and tracking errors PARAMETER Maximum peak transmit overload level TEST CONDITIONS‡ MIN TYP‡ TP3064B, TP13064B 3.17 dBm0 2.501 TP3067B, TP13067B 3.14 dBm0 2.492 Transmit filter gain, absolute (at 0 dBm0) TA = 25°C f = 16 Hz – 0.15 Absolute transmit gain variation with temperature and supply voltage UNIT V 0.15 dB – 40 f = 50 Hz – 30 f = 60 Hz – 26 f = 200 Hz Transmit filter gain, relative to absolute MAX – 1.8 – 0.1 f = 300 Hz to 3000 Hz – 0.15 0.15 f = 3300 Hz – 0.35 0.05 f = 3400 Hz – 0.8 0 f = 4000 Hz – 14 f ≥ 4600 Hz (measure response from 0 Hz to 4000 Hz) – 32 Relative to absolute transmit gain – 0.1 dB 0.1 dB Sinusoidal test method; Reference level = – 10 dBm0 Transmit gain tracking error with level Receive filter gain, absolute (at 0 dBm0) Receive filter gain, gain relative to absolute 3 dBm0 ≥ input level ≥ – 40 dBm0 ± 0.2 – 40 dBm0 > input level ≥ – 50 dBm0 ± 0.4 – 50 dBm0 > input level ≥ – 55 dBm0 ± 0.8 Input is digital code sequence for 0 dBm0 signal, TA = 25°C – 0.15 0.15 f = 0 Hz to 3000 Hz, – 0.15 0.15 f = 3300 Hz – 0.35 0.05 f = 3400 Hz – 0.8 0 TA = 25°C f = 4000 Hz Absolute receive gain variation with temperature and supply voltage TA = full range, dB dB dB – 14 See Note 4 – 0.1 0.1 dB 3 dBm0 ≥ input level ≥ – 40 dBm0 ± 0.2 dB – 40 dBm0 > input level ≥ – 50 dBm0 ± 0.4 – 50 dBm0 > input level ≥ – 55 dBm0 ± 0.8 RL = 10 kΩ ± 2.5 V ± 0.25 dB Sinusoidal test method; reference input PCM code corresponds to an ideally encoded – 10 dBm0 signal Receive gain g tracking g error with level Receive output drive voltage Transmit and receive gain tracking error with level (A-law, CCITT C712) Pseudo-noise test method; reference input PCM code corresponds to an ideally encoded – 10 dBm0 signal 3 dBm0 ≥ input level ≥ – 40 dBm0 – 40 dBm0 > input level ≥ – 50 dBm0 ± 0.3 – 50 dBm0 > input level ≥ – 55 dBm0 ± 0.45 † All typical values are at VCC = 5 V, VBB = – 5 V, and TA = 25°C. ‡ Absolute rms signal levels are defined as follows: VI = 1.2276 V = 0 dBm0 = 4 dBm at f = 1.02 kHz with RL = 600 Ω. NOTE 4: Full range for the TP3064B and TP3067B is 0°C to 70°C. Full range for the TP13064B and TP13067B is – 40°C to 85°C. 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 envelope delay distortion with frequency PARAMETER TYP† MAX UNIT f = 1600 Hz 290 315 µs f = 500 Hz to 600 Hz 195 220 f = 600 Hz to 800 Hz 120 145 f = 800 Hz to 1000 Hz 50 75 f = 1000 Hz to 1600 Hz 20 40 f = 1600 Hz to 2600 Hz 55 75 f = 2600 Hz to 2800 Hz 80 105 f = 2800 Hz to 3000 Hz 130 155 180 200 µs µs TEST CONDITIONS Transmit delay, absolute (at 0 dBm0) Transmit filter gain, relative to absolute Receive delay, absolute (at 0 dBm0) MIN f = 1600 Hz Receive delay, relative to absolute f = 500 Hz to 1000 Hz – 40 – 25 f = 1000 Hz to 1600 Hz – 30 – 20 f = 1600 Hz to 2600 Hz 70 90 f = 2600 Hz to 2800 Hz 100 125 f = 2800 Hz to 3000 Hz 140 175 TYP† MAX µs † All typical values are at VCC = 5 V, VBB = – 5 V, and TA = 25°C. noise PARAMETER TEST CONDITIONS MIN UNIT Transmit noise, C-message weighted‡ TP3064B, TP13064B VFXI = 0 V 5 9 dBrnC0 Transmit noise, psophometric weighted (see Note 5) TP3067B, TP13067B VFXI = 0 V – 74 – 69 dBm0p Receive noise, C-message weighted TP3064B, TP13064B PCM code equals alternating positive and negative zero 2 4 dBrnC0 Receive noise, psophometric weighted TP3067B, TP13067B PCM code equals positive zero – 86 – 83 dBm0p – 53 dBm0 Noise, single frequency VFXI+ = 0 V, f = 0 kHz to 100 kHz, Loop-around measurement † All typical values are at VCC = 5 V, VBB = – 5 V, and TA = 25°C. ‡ This parameter is achieved through use of patented circuitry and is not recommended for applications in which the composite signals on the transmit side are below – 55 dBm0. NOTE 5: Measured by extrapolation from the distortion test result POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 power supply rejection PARAMETER Positive power-supply rejection, transmit TEST CONDITIONS f = 0 Hz to 4 kHz VCC = 5 V + 100 mVrms, V VFXI+ = – 50 dBm0 MIN f = 0 Hz to 4 kHz VBB = – 5 V + 100 mVrms, V VFXI+ = – 50 dBm0 38 µ-law 38 dB dBC† 40 dB A-law 35 µ-law 35 dB dBC† 40 dB A-law 40 µ-law 40 dB dBC† f = 4 kHz to 50 kHz Positive power-supply rejection, receive Negative power-supply rejection, receive f = 0 Hz to 4 kHz PCM code d equals l positive iti zero, VCC = 5 V + 100 mVrms f = 4 kHz to 50 kHz f = 0 Hz to 4 kHz d equals l positive iti zero, PCM code VBB = – 5 V + 100 mVrms 40 dB A-law 38 µ-law 38 dB dBC† 40 dB f = 4 kHz to 50 kHz 0 dBm0, 300-Hz to 3400-Hz input applied to DR (measure individual image signals at VFRO) – 30 f = 4600 Hz to 7600 Hz – 33 f = 7600 Hz to 8400 Hz – 40 f = 8400 Hz to 100 kHz † The unit dBC applies to C-message weighting. – 40 S Spurious out-of-band signals at the channel output (VFRO) UNIT A-law f = 4 kHz to 50 kHz Negative power-supply rejection, transmit MAX dB dB distortion PARAMETER TEST CONDITIONS MIN Level = 3 dBm0 Level = 0 dBm0 to – 30 dBm0 Signal to distortion ratio, Signal-to-distortion ratio transmit or receive half half-channel channel‡ Level = – 40 dBm0 Level = – 55 dBm0 MAX UNIT 33 36 Transmit 29 Receive 30 Transmit 14 Receive 15 dBC† Single-frequency distortion products, transmit – 46 dB Single-frequency distortion products, receive – 46 dB – 41 dB Loop-around measurement, VFXI+ = – 4 dBm0 to – 21 dBm0, Two frequencies in the range of 300 Hz to 3400 Hz Intermodulation distortion Si l t di t ti ratio, ti transmit t it half-channel h lf h l (A l ) Signal-to-distortion (A-law) (CCITT G.714) G 714)§ Si l t di t ti ratio, ti receive i h lf h l (A l ) Signal-to-distortion half-channel (A-law) (CCITT G.714) G 714)§ Level = – 3 dBm0 33 Level = – 6 dBm0 to – 27 dBm0 36 Level = – 34 dBm0 33.5 Level = – 40 dBm0 28.5 Level = – 55 dBm0 13.5 Level = – 3 dBm0 33 Level = – 6 dBm0 to – 27 dBm0 36 Level = – 34 dBm0 34.2 Level = – 40 dBm0 30 dB dB Level = – 55 dBm0 15 † The unit dBC applies to C-message weighting. ‡ Sinusoidal test method (see Note 6). § Pseudo-noise test method NOTE 6: The TP13064A and TP3064A are measured using a C-message filter. The TP13067A and TP3067A are measured using a psophometric weighted filter. 10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 crosstalk PARAMETER TEST CONDITIONS Crosstalk, transmit to receive f = 300 Hz to 3000 Hz, MIN DR at steady PCM code Crosstalk, receive to transmit (see Note 7) VFXI = 0 V, f = 300 Hz to 3000 Hz † All typical values are at VCC = 5 V, VBB = – 5 V, and TA = 25°C. NOTE 7: Receive-to-transmit crosstalk is measured with a – 50 dBm0 activation signal applied to VFXI+. TYP† MAX UNIT – 90 – 75 dB – 90 – 72 dB MIN MAX UNIT power amplifiers PARAMETER TEST CONDITIONS Balanced load, RL, connected between VPO+ and VPO – Maximum 0 dBm0 rms level for better than ± 0.1 dB linearity over the range if – 10 dBm0 to 3 dBm0 Signal/distortion POST OFFICE BOX 655303 RL = 600 Ω 3.3 RL = 1200 Ω 3.5 RL = 30 kΩ 4 RL = 600 Ω 50 • DALLAS, TEXAS 75265 VRMS dB 11 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 PARAMETER MEASUREMENT INFORMATION td2 TSX td3 20% 20% tr1 tw2 tf1 MCLKX MCLKR 80% fclock(M) 80% 80% 20% 20% tsu1 tw1 80% BCLKX 80% 80% 1 2 3 4 5 6 7 8 20% th2 tsu4 th4 80% FSX 80% 20% td3 td1 1 DX 2 3 4 5 6 80% BCLKR 20% 1 2 3 4 5 6 80% 20% 7 7 8 8 80% 20% 20% th2 tsu4 th4 FSR 80% 20% tsu3 th3 th3 DR 1 2 3 4 5 Figure 1. Short-Frame Sync Timing 12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 6 7 8 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 PARAMETER MEASUREMENT INFORMATION tw1 tr1 fclock(M) tf1 MCLKX MCLKR 80% 20% tw2 80% 20% 80% 20% tr2 tsu1 tw3 tf2 tsu1 80% BCLKX 1 20% 80% 20% 2 80% 20% tw4 80% 3 20% 4 th1 6 7 8 th5 80% 20% 80% 20% td4 td1 td4 td3 80% DX 20% 1 2 3 4 tw3 5 6 7 80% 20% 20% 80% 20% 8 td3 tw4 80% BCLKR 9 fclock(B) tsu2 FSX 5 80% 20% th1 tsu2 FSR th5 80% 20% 80% tsu3 th3 DR 1 2 3 4 5 th3 6 7 8 Figure 2. Long-Frame Sync Timing POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 13 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 PRINCIPLES OF OPERATION system reliability and design considerations TP306xB, TP1306xB system reliability and design considerations are detailed in the following paragraphs. latch-up Latch-up is possible in all CMOS devices. It is caused by the firing of a parasitic SCR that is present due to the inherent nature of CMOS. When a latch-up occurs, the device draws excessive amounts of current and will continue to draw heavy current until power is removed. Latch-up can result in permanent damage to the device if supply current to the device is not limited. Even though the TP306xB and TP1306xB devices are heavily protected against latch-up, it is still possible to cause latch-up under certain conditions in which excess current is forced into or out of one or more terminals. Latch-up can occur when the positive supply voltage drops momentarily below ground, when the negative supply voltage rises momentarily above ground, or possibly if a signal is applied to a terminal after power has been applied but before the ground is connected. This can happen if the device is hot-inserted into a card with the power applied, or if the device is mounted on a card with an edge connector, and the card is hot-inserted into a system with the power on. To help ensure that latch-up does not occur, it is considered good design practice to connect a reversed biased Schottky diode (with a forward voltage drop of less than or equal to 0.4 V — 1N5711 or equivalent), between each power supply and GND (see Figure 3). If it is possible that a TP306xB- or TP1306xB-equipped card that has an edge connector could be hot-inserted into a powered-up system, it is also important to ensure that the ground edge connector traces are longer than the power and signal traces so that the card ground is always the first to make contact. device power-up sequence Latch-up can also occur if a signal source is connected without the device being properly grounded. A signal applied to one terminal could then find a ground through another signal terminal on the device. To ensure proper operation of the device and as a safeguard against this sort of latch-up, it is recommended the following power-up sequence always be used: 1. Ensure no signals are applied to the device before the power-up sequence is complete. 2. Connect GND. 3. Apply VBB (most negative voltage). 4. Apply VCC (most positive voltage). 5. Force a power down condition in the device. 6. Connect clocks. 7. Release power down condition. 8. Apply FSX and/or FXR synchronization pulses. 9. Apply signal inputs. When powering down the device, this procedure should be followed in the reverse order. 14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 PRINCIPALS OF OPERATION VCC DGND VBB Figure 3. Diode Configuration for Latch-Up Protection Circuitry internal sequencing Power-on reset circuitry initializes the TP3064B, TP3067B, TP13064B, and TP13067B devices when power is first applied, placing it into the power-down mode. DX and VFRO outputs go into high-impedance states and all nonessential circuitry is disabled. A low level or clock applied to MCLKR/PDN powers up the device and activates all circuits. DX, a 3-state PCM data output, remains in the high-impedance state until the arrival of the second FSX pulse. power supplies All ground connections to each device should meet at a common point as close as possible to ANLG–GND. This minimizes the interaction of ground return currents flowing through a common bus impedance. VCC and VBB supplies should be decoupled by connecting 0.1-µF decoupling capacitors between each power rail and this common point. These bypass capacitors must be connected as close as possible to VCC and VBB. For best performance, the ground point of each codec/filter on a card should be connected to a common card ground in star formation rather than through a ground bus. This common ground point should be decoupled to VCC and VBB with 10-µF capacitors. synchronous operation For synchronous operation, a clock is applied to MCLKX. MCLKR/PDN is used as a power-down control. A logic 0 applied to MCLKR powers-up the device and a high level powers it down. In either case, MCLKX is selected as the master clock for both receive and transmit direction. BCLKX must also have a bit clock applied to it. The selection of the proper internal divider for a master-clock frequency of 1.536 MHz, 1.544 MHz, or 2.048 MHz can be done using BCLKR/CLKSEL. The device automatically compensates for the 193rd clock pulse of each frame. A fixed level on BCLKR/CLKSEL selects BCLKX as the bit clock for both the transmit and receive directions. Table 1 indicates the frequencies of operation that can be selected depending on the state of BCLKR/CLKSEL. In the synchronous mode, BCLKX may be in the range from 64 kHz to 2.048 MHz but must be synchronous with MCLKX. The encoding cycle begins with each FSX pulse, and the PCM data from the previous cycle is shifted out of the enabled DX output on the rising edge of BCLKX. After eight-bit clock periods, the 3-state DX output is returned to the high-impedance state. With an FSR pulse, PCM data is latched via DR on the falling edge of BCLKX (or BCLKR, if running). FSX and FSR must be synchronous with MCLKX and MCLKR. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 15 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 PRINCIPALS OF OPERATION asynchronous operation For asynchronous operation, separate transmit and receive clocks can be applied. MCLKX and MCLKR must be 2.048 MHz for the TP3064B and TP13064B, 1.536 MHz or 1.544 MHz for the TP3067B and TP13067B and need not be synchronous. However, for best performance, MCLKR should be synchronous with MCLKX. This is easily achieved by applying only static logic levels to MCLKR/PDN. This connects MCLKX to all internal MCLKR functions. For 1.544-MHz operation, the device compensates for the 193rd clock pulse of each frame. Each encoding cycle is started with FSX, and FSX must be synchronous with MCLKX and BCLKX. Each decoding cycle is started with FSR, and FSR must be synchronous with BCLKR. The logic levels shown in Table 1 are not valid in the asynchronous mode. BCLKX and BCLKR can operate from 64 kHz to 2.048 MHz. short-frame sync operation The device can operate with either a short- or a long-frame sync pulse. On power up, the device automatically goes into the short-frame mode where both FSX and FSR must be one bit-clock period long, with timing relationships specified in Figure 1. With FSX high during a falling edge of BCKLX, the next rising edge of BCLKX enables the 3-state output buffer, DX, which outputs the sign bit. The remaining seven bits are clocked out on the following seven rising edges, and the next falling edge disables DX. With FSR high during a falling edge of BCLKR (BCLKX in synchronous mode), the next falling edge of BCLKR latches in the sign bit. The following seven falling edges latch in the seven remaining bits. The short-frame sync pulse may be utilized in either the synchronous or asynchronous mode. Table 1. Selection of Master-Clock Frequencies BCLKR/CLKSEL MASTER-CLOCK FREQUENCY SELECTED TP3064B, TP13064B TP3067B, TP13067B Clock Input 1.536 MHz or 1.544 MHz 2.048 MHz Logic Input L (sync mode only) 2.048 MHz 1.536 MHz or 1.544 MHz Logic Input H (open) (sync mode only) 1.536 MHz or 1.544 MHz 2.048 MHz long-frame sync operation Both FSX and FSR must be three or more bit-clock periods long to use the long-frame sync mode with timing relationships as shown in Figure 2. Using the transmit frame sync (FSX), the device detects whether a shortor long-frame sync pulse is being used. For 64-kHz operation, the frame-sync pulse must be kept low for a minimum of 160 ns. The rising edge of FSX or BCLKX, which ever occurs later, enables the DX 3-state output buffer. The first bit clocked out is the sign bit. The next seven rising edges of BCLKX edges clock out the remaining seven bits. The falling edge of BCLKX following the eighth rising edge or FSX going low, whichever occurs later, disables DX. A rising edge on FSR, the receive frame sync pulse, causes the PCM data at DR to be latched in on the next eight falling edges of BCLKR (BCLKX in synchronous mode). The long-frame sync pulse can be used in either the synchronous or asynchronous mode. 16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 PRINCIPALS OF OPERATION transmit section The transmit section input is an operational amplifier with provision for gain adjustment using two external resistors. Gains in excess of 20 dB across the audio pass band are possible via low noise and wide bandwidth. The operational amplifier drives a unity-gain filter consisting of an RC active prefilter followed by an eight-order switched-capacitor band-pass filter clocked at 256 kHz. The output of this filter directly drives the encoder sample-and-hold circuit. As per µ-law (TP3064B and TP13064B) or A-law (TP3067B and TP13067B) coding conventions, the ADC is a companding type. A precision voltage reference provides a input overload of nominally 2.5-V peak. The sampling of the filter output is controlled by the FSX frame-sync pulse. Then the successive-approximation encoding cycle begins. The 8-bit code is loaded into a buffer and shifted out through DX at the next FSX pulse. The total encoding delay is approximately 290 µs. Any offset voltage due to the filters or comparator is cancelled by sign bit integration (see Table 2). Table 2. Encoding Format at DX Output TP3064B, TP13064B µ-LAW TP3067B, TP13067B A-LAW (INCLUDES EVEN-BIT INVERSION) VI = + Full scale 1 0 0 0 0 0 0 0 1 0 1 0 1 0 1 0 VI = 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 VI = – Full scale 0 0 0 0 0 0 0 0 0 0 1 0 1 0 1 0 receive section The receive section consists of an expanding DAC that drives a fifth-order low-pass filter clocked at 256 kHz. The decoder is µ-law (TP3064B and TP13064B) or A-law (TP3067B and TP13067B) and the fifth-order low-pass filter corrects for the (sin x)/x attenuation caused by the 8-kHz sample/hold. The filter is followed by a second-order RC active post-filter with its output at VFRO. The receive section is unity-gain but gain can be added by using the power amplifiers. At FSR, the data at DR is clocked in on the falling edge of the next eight BCLKR (BCLKX) periods. At the end of the decoder time slot, the decoding cycle begins and 10 µs later the decoder DAC output is updated. The decoder delay is about 10 µs (decoder update) plus 110 µs (filter delay) plus 62.5 µs (1/2 frame), or a total of approximately180 µs. receive power amplifiers Two inverting-mode power amplifiers are provided for directly driving a match-line interface transformer. The gain of the first power amplifier can be adjusted to boost the ± 2.5-V peak output signal from the receive filter up to the ± 3.3-V peak into an unbalanced 300-Ω load, or ± 4 V into an unbalanced 15-kΩ load. The second power amplifier is internally connected in unity-gain inverting mode to give 6-dB signal gain for balanced loads. Maximum power transfer to a 600-Ω subscriber line termination is obtained by differentially driving a balanced transformer with √2:1 turns ratio, as shown in Figure 3. A total peak power of 15.6 dBm can be delivered to the load plus termination. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 17 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 APPLICATION INFORMATION power supplies While the pins of the TP1306xB and TP306xB families are well protected against electrical misuse, it is recommended that the standard CMOS practice be followed ensuring that ground is connected to the device before any other connections are made. In applications where the printed-circuit board can be plugged into a hot socket with power and clocks already present, an extra long ground pin in the connector should be used. All ground connections to each device should meet at a common point as close as possible to ANLG GND. This minimizes the interaction of ground return currents flowing through a common bus impedance. VCC and VBB supplies should be decoupled by connecting 0.1-µF decoupling capacitors to this common point. These bypass capacitors must be connected as close as possible to VCC and VBB. For best performance, the ground point of each codec/filter on a card should be connected to a common card ground in star formation rather than via a ground bus. This common ground point should be decoupled to VCC and VBB with 10-µF capacitors. 18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 APPLICATION INFORMATION 600 Ω 2 Hybrid 1 1 300 Ω 2 ZBAL 5V –5 V 300 Ω R2 0.1 µF 6 VCC 0.1 µF GND 20 VBB 1 VPO + 3 VPO – R3 4 VPI VFXI + TP3064B TP3067B TP13064B TP13067B VFXI – FSR DR BCLKR MCLKR/PDN GSX 7 8 9 10 B. Receive gain = 20 log 17 16 15 14 13 12 11 VFRO NOTES: A. Transmit gain = 20 log 18 R1 R4 5 19 ANLG LOOP TSX FSX DX BCLKX MCLKX R1 + R2 , (R1 + R2) ≥ 10 kΩ R2 2 × R3 , R4 ≥ 10 kΩ R4 Figure 4. Typical Synchronous Application POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 19 TP3064B, TP3067B, TP13064B, TP13067B MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER SCTS031D – MAY 1990 –REVISED JULY 1996 APPLICATION INFORMATION 17 GSX 16 R2 18 VFXI – 19 R1 ANLG LOOP Autozero Logic – + VFXI + Analog Input RC Active Filter R SwitchedCapacitor Band-Pass Filter S/H DAC – 1 VPO+ + R VPO– Transmit Regulator 13 DX OE Comparator – 3 A/D Control Logic Voltage Reference + R3 RC Active Filter 4 VPI SwitchedCapacitor Low-Pass Filter Receive Regulator S/H DAC 8 DR CLK R4 5 VFRO 15 Timing and Control 5V 11 6 VCC 20 TSX –5 V 20 VBB 10 12 9 7 14 2 ANLG GND POST OFFICE BOX 655303 MCLKX MCLKR/ PDN • DALLAS, TEXAS 75265 BCLKX BCLKR/ FSR FSX CLKSEL IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated