Ordering number : ENA0887 Monolithic Linear IC LA73065VA For wideband 75Ω Video Driver Overview This LA73065VA is HD video driver. This IC output Component and RGB. It built in the 12MHz/30MHz-LPF. It is the best for the filter to remove the digital clock noise of the Component or RGB Analog video signal. Functions • Three channel output • 12MHz or 30MHz low pass filter • 6dB amplifier • Output mute • D_DC_Output • Standby mode Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Allowable power dissipation Symbol Conditions Ratings VCC max Pd max Ta ≤ 75°C * Unit 6.0 V 500 mW Operating temperature Topr -20 to +75 °C Storage temperature Tstg -40 to +150 °C * : Mounted on a board : 114.3mm×76.1mm×1.6mm, glass epoxy board. Recommended Operating Conditions at Ta = 25°C Parameter Symbol Recommended supply voltage VCC Operating supply voltage range VCC opg Input pin voltage application range VIN Conditions Ratings Unit 5.0 V 4.75 to 5.25 V -0.3 to VCC opg+0.3 Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. 80807 MS PC 20070703-S00004 No.A0887-1/9 LA73065VA Electrical Characteristics at Ta = 25°C, VCC = 5.0V Input signal Parameter Out Level Freq [Vp-p] [Hz] Point Conditions min typ max unit Point Signal Current consumption 1 - - - - - At no signal. 36 45 54 mA Current consumption 2 - - - - - At no signal. Standby mode. 0.0 0.5 1.0 mA - - - - T24 2.8 3.0 3.2 V Voltage gain 1 T9A SIG1 0.3 100k T16 Output gain 5.5 6.0 6.5 dB Py, R, G, B T7A T18 T9A T16 Output gain 5.5 6.0 6.5 dB -3 0.0 3 dB -3 0.0 3 dB -40 -30 dB -40 -30 dB -1 0.0 1 dB -1 0.0 1 dB -3.5 -1.0 1.5 dB -3.5 -1.0 1.5 dB -40 -30 dB -40 -30 dB Internal reference regulator REG3V Video Driver part T11A T14 Voltage gain 2 T7A SIG3 0.3 100k T18 Pr, Pb T11A Frequency response 1 T9A T16 12MHz LPF is selected. Py, R, G, B T7A T18 f = 12MHz/100kHz T9A T16 T14 SIG1 0.3 12M T14 T11A Frequency response 2 T7A SIG3 Pr, Pb T11A Frequency response 3 T9A Py, R, G, B T7A T9A T16 SIG1 0.3 0.3 12M 75M T11A T18 12MHz LPF is selected. T14 f = 12MHz/100kHz T16 12MHz LPF is selected. T18 f = 75MHz/100kHz T14 Frequency response 4 T7A SIG3 Pr, Pb T11A Frequency response 5 T9A Py, R, G, B T7A T9A T14 SIG1 0.3 0.3 75M 20M T18 12MHz LPF is selected. T14 f = 75MHz/100kHz T16 30MHz LPF is selected. T16 f = 20MHz/100kHz T11A Frequency response 6 T7A Pr, Pb T11A SIG3 Frequency response 7 T9A Py, R, G, B T7A T9A T14 SIG1 0.3 0.3 20M 30M T18 30MHz LPF is selected. T14 f = 20MHz/100kHz T16 30MHz LPF is selected. T16 f = 30MHz/100kHz T11A Frequency response 8 T7A Pr, Pb T11A SIG3 Frequency response 9 T9A Py, R, G, B T7A T9A T14 SIG1 0.3 0.3 30M 75M T18 30MHz LPF is selected. T14 f = 30MHz/100kHz T16 30MHz LPF is selected. T16 f = 75MHz/100kHz T11A Frequency response 10 T7A Pr, Pb T11A SIG3 2nd order distortion 1 T9A Py, R, G, B T7A T18 T9A T16 SIG1 0.3 0.7 75M 10M T18 30MHz LPF is selected. T14 f = 75MHz/100kHz T16 30MHz LPF is selected. -40 -30 dB 30MHz LPF is selected. -40 -30 dB -60 -50 dB -60 -50 dB -60 -50 dB T14 T11A 2nd order distortion 2 (HD) T7A SIG3 0.7 10M Pr, Pb T11A Amount of mute attenuation 1 T9A Py, R, G, B T7A T18 T9A T16 T14 SIG1 0.7 4M T7A Pr, Pb T11A Crosstalk between channels 1 T9A Py, R, G, B T7A T16 T14 T11A Amount of mute attenuation 2 T18 SIG3 0.7 4M T18 T14 SIG1 0.7 4M T9A T11A Continued on next page. No.A0887-2/9 LA73065VA Continued from preceding page. Input signal Parameter Out Level Freq [Vp-p] [Hz] 4M Signal Crosstalk between channels 2 T7A SIG3 0.7 Pr, Pb T11A Video S/N T9A SIG2 0.65 Py, R, G, B T7A T18 VIN = Video (50% White) 30MHz LPF is selected. T9A T16 The band is between 100kHz T11A T14 and 30MHz. T16 12MHz LPF is selected. f = 12MHz/100kHz SIG1 0.3 Point Conditions Point T16 12M G.D.1 T9A Py, R, G, B T7A T18 T9A T16 G.D.2 T7A Pr, Pb T11A G.D.3 T9A Py, R, G, B T7A SIG3 0.3 T9A T16 SIG1 0.3 12M 30M T11A T7A Pr, Pb T11A typ max unit -60 -50 dB -60 -50 dB 10 20 ns 10 20 ns 10 20 ns 10 20 ns T14 T11A G.D.4 min T18 12MHz LPF is selected. T14 f = 12MHz/100kHz T16 30MHz LPF is selected. T18 f = 30MHz/100kHz T14 SIG3 0.3 30M T18 30MHz LPF is selected. T14 f = 30MHz/100kHz Package Dimensions unit : mm (typ) 3287 6.5 24 0.5 6.4 4.4 13 12 1 0.5 0.15 0.22 0.1 (1.3) 1.5max (0.5) SANYO : SSOP24(225mil) No.A0887-3/9 LA73065VA Block Diagram SW1:Power Save CTL VREG_3V VREG_3V 47μF + 24 2 5V/2.2V/0V 23 3 5V/0V 22 5V/2.2V/0V 21 1 D_LINE1_IN (High/Open/Low) REG3V D_LINE2_IN (High/Low) D_LINE3_IN (High/Open/Low) 10kΩ 10kΩ D_LINE1_OUT D_LINE2_OUT REG3V 4 10kΩ D_LINE3_OUT SW2:Input CTL (CLAMP or BIAS) 5 20 N.C. VCC_HD 6 19 VCC_DR_HD Pr/R_IN 1μF + SW3:Firter CTL (12MHz or 30MHz) Py/G_IN 1μF + CLAMP SW2 12MHz SW3 LPF BIAS 100kΩ 30MHz LPF 7 6dB Pb/B_IN 1μF + GND_HD SW4 330μF 18 + 17 12MHz LPF CLAMP 9 SW3 MUTE 6dB SW4 BIAS 100kΩ 30MHz LPF 11 MUTE 6dB N.C. 1000μF 16 + 15 12MHz SW3 LPF 75Ω 75Ω Py/G_OUT 75Ω Driver 10 CLAMP SW2 75Ω Pr/R_OUT Driver 8 30MHz LPF SW4:HD Mute CTL MUTE SW4 GND_DR_HD 330μF 14 + 75Ω Pb/B_OUT 75Ω Driver 12 13 N.C. Please shorten the distance of the bold line to prevent oscillation. Pin control table OUT_Pin No. SW function name Control voltage SW No. IN_Pin No. SW1 Pin1 Power_Save_CTL Power_Save_OFF Power_Save_ON SW2 Pin5 Input_CTL CLAMP_ON (RGB_Mode) BIAS_ON (Component_Mode) High (2.3V to VCC) Open Low (0 to 0.7V) SW3 Pin8 Filter_CTL 12MHz_LPF_ON 30MHz_LPF_ON SW4 Pin10 HD_MUTE_CTL HD_MUTE_OFF HD_MUTE_ON D_L1 Pin2 Pin23 D_LINE1 High (4.0V to VCC) D_L2 Pin3 Pin22 D_LINE2 High (4.0V to VCC) D_L3 Pin4 Pin21 D_LINE3 High (4.0V to VCC) Midd (1.8 to 2.4V) Low (0 to 0.5V) Low (0 to 0.5V) Midd (1.8 to 2.4V) Low (0 to 0.5V) No.A0887-4/9 LA73065VA Pin Functions Pin No. Pin name 1 Power_Save_CTL DC voltage Signal wave form Input/Output form 5V : Power_Save_OFF 0V : Power_Save_ON 10kΩ 1 100kΩ 2 D_LINE1_IN 5V : 1125 (1080) 3V_REG OPEN : 750 (720) 200kΩ 0V : 525 (480) 2 10kΩ 200kΩ 3 D_LINE2_IN 5V : 59.94p/60p 0V : 59.94i/60i 10kΩ 3 100kΩ 4 D_LINE3_IN 5V : 16 : 9 OPEN : 4 : 3 200kΩ Letter Box 4 10kΩ 0V : 4 : 3 200kΩ 5 INPUT_CTL 5V : Clamp 0V : Bias 10kΩ 5 100kΩ Continued on next page. No.A0887-5/9 LA73065VA Continued from preceding page. Pin No. Pin name 6 VCC_HD 7 Pr/R_IN DC voltage Signal wave form Input/Output form Component : 2.3V (Bias) 500Ω 700mVp-p RGB : 1.8V (Clamp) Clamp:OFF 2.3V 7 1kΩ 1kΩ 100kΩ 700mVp-p 110μA Bias:OFF 1.8V 50μA 8 FIL_CTL 5V : 12MHz_LPF 0V : 30MHz_LPF 10kΩ 8 100kΩ 9 Py/G_IN 1.8V 500Ω 1.0Vp-p 1.8V 1kΩ 1kΩ 9 700mVp-p 1.8V 10 HD_MUTE_CTL 110μA 5V : HD_MUTE_OFF 0V : HD_MUTE_ON 10kΩ 10 100kΩ Continued on next page. No.A0887-6/9 LA73065VA Continued from preceding page. Pin No. 11 Pin name Pb/B_IN DC voltage Signal wave form Input/Output form Component : 2.3V (Bias) 500Ω 700mVp-p RGB : 1.8V (Clamp) Clamp:OFF 2.3V 11 1kΩ 1kΩ 100kΩ 700mVp-p 110μA Bias:OFF 1.8V 50μA 12 GND_HD 13 N.C. 14 Pb/B_OUT Component : 2.4V (Bias) 30Ω RGB : 1.3V (Clamp) 1.4Vp-p 2.4V 1.3kΩ 1.5kΩ 14 1.4Vp-p 30Ω 1.3V 15 GND_DR_HD 16 Py/G_OUT 1.3V 30Ω 2.0Vp-p 1.3V 1.3kΩ 1.5kΩ 16 1.4Vp-p 30Ω 1.3V 17 N.C. Continued on next page. No.A0887-7/9 LA73065VA Continued from preceding page. Pin No. 18 Pin name Pr/R_OUT DC voltage Signal wave form Input/Output form Component : 2.4V (Bias) 30Ω RGB : 1.3V (Clamp) 1.4Vp-p 2.4V 1.3kΩ 1.5kΩ 18 1.4Vp-p 30Ω 1.3V 19 VCC_DR_HD 20 N.C. 21 D_LINE3_OUT 5V : 16 : 9 High:OFF 2.2V : 4 : 3Letter Box 0V : 4 : 3 OPEN:OFF 300Ω 21 500μA Low:OFF 22 D_LINE2_OUT 5V : 59.94p/60p 0V : 59.94i/60i 300Ω 23 D_LINE1_OUT 22 5V : 1125 (1080) High:OFF 2.2V : 750 (720) 0V : 525 (480) OPEN:OFF 300Ω 23 500μA Low:OFF 24 REG3V 3.0V 50Ω 100Ω 26kΩ 32kΩ 30kΩ 24kΩ 24 No.A0887-8/9 LA73065VA Test Input Signal SIN WAVE Vp-p SIG.1 1H 0.3Vp-p 0.35Vp-p SIG.2 1H Vp-p 0.3Vp-p SIN WAVE SIG.3 SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information information as as of of January, August, 2007. 2007. Specifications Specifications and and information information herein are subject to change without notice. PS No.A0887-9/9