RClamp0854P RailClamp® Low Capacitance TVS Array PROTECTION PRODUCTS - RailClamp® Description Features Transient protection for high-speed data lines to RailClamp® is a low capacitance TVS array designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are connected to data and transmission lines from overvoltage caused by ESD (electrostatic discharge), CDE (Cable Discharge Events), and EFT (electrical fast transients). The RClamp0854P is specifically designed to protect portable devices that utilize the USB port for battery charging. The unique design of this device features low capacitance TVS diodes for protection of the USB data (DP, DM) and USB ID (accessory detect) pins operating up to 5.5 volts. Loading capacitance on these lines is <0.1pF for maximum signal integrity. An integrated 5.5 volt TVS diode is used for protection of the USB voltage bus. This ensures the device will remain in a high-impedance state during normal USB operation or when the battery is being charged. The RClamp0854P is in a 6-pin, RoHS compliant, SLP1616P6 package. It measures 1.6 x 1.6 x 0.60mm. The leads are spaced at a pitch of 0.5mm and are finished with lead-free NiPdAu. They may be used to meet the ESD immunity requirements of IEC 61000-4-2, Level 4 (15kV air, 8kV contact discharge). IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact) IEC 61000-4-4 (EFT) 40A (5/50ns) Array of surge rated diodes with internal TVS Diode Small package (1.6 x 1.6mm) saves board space Protects USB DP, DM, and ID Pin operating up to 5.5V Protects USB VBus operating up to 5.5V Low capacitance (<1pF) on DP, DM, and ID Pins No insertion loss to 2.0GHz Low leakage current Low clamping voltage Large ground pad for increased ESD performance Solid-state silicon-avalanche technology Mechanical Characteristics SLP1616P6 6L package RoHS/WEEE Compliant Nominal Dimensions: 1.6 x 1.6 x 0.60 mm Lead Finish: NiPdAu Molding compound flammability rating: UL 94V-0 Marking : Marking code + two character date code Packaging : Tape and Reel Applications USB 2.0 USB OTG Circuit Diagram PIN Configuration 6 1 2 DM 1 3 5.5V DP 2 USB ID 3 5.5V GND Gnd 6 VBus 5 NC 4 NC SLP1616P6 (Top View) Revision 07/18/2008 1 www.semtech.com RClamp0854P PROTECTION PRODUCTS Absolute Maximum Rating R ating Symbol Value Units Peak Pulse Power (tp = 8/20μs) Pp k 100 Watts Peak Pulse Current (tp = 8/20μs) IP P 3 A ESD per IEC 61000-4-2 (Air) ESD per IEC 61000-4-2 (Contact) VESD ±15 ±8 kV TJ -55 to +125 °C TSTG -55 to +150 °C Peak Pulse Power (tp = 8/20μs) Pp k 200 Watts Peak Pulse Current (tp = 8/20μs) IP P 16 A ESD per IEC 61000-4-2 (Air) ESD per IEC 61000-4-2 (Contact) VESD ±15 ±8 kV TJ -55 to +125 °C TSTG -55 to +150 °C D P, D M , U S B I D ( P i n s 1 , 2 , 3 ) Operating Temperature Storage Temperature V B u s ( P i n 6) Operating Temperature Storage Temperature © 2008 Semtech Corp. 2 www.semtech.com RClamp0854P PROTECTION PRODUCTS Electrical Characteristics (T = 25oC) D M , D P, U S B I D T V S ( P i n s 1 , 2 , 3 ) Parameter Symbol Conditions Reverse Stand-Off Voltage VRWM Pin 1, 2, or 3 to GN D Reverse Breakdown Voltage V BR It = 1mA, Pin 1, 2, or 3 to GN D Reverse Leakage Current IR VRWM = 5.5V, Pin 1, 2, or 3 to GN D Forward Voltage VF If = 15mA GN D to Pin 1, 2, or 3 Clamping Voltage VC Clamping Voltage Junction Capacitance Maximum Units 5.5 V 8 10 V 0.100 1 μA 1.2 V IPP = 1A, tp = 8/20μs Pin 1, 2, or 3 to GN D 15 V VC IPP = 3A, tp = 8/20μs Pin 1, 2, or 3 to GN D 30 V Cj VR = 0V, f = 1MHz, Pin 1, 2, or 3 to GN D 0.95 pF 0.5 pF VR = 0V, f = 1MHz, Between I/O pins © 2008 Semtech Corp. 3 Minimum 6.5 Typical 0.6 0.8 www.semtech.com RClamp0854P PROTECTION PRODUCTS Electrical Characteristics (T = 25oC) V B u s T V S ( P i n 6) Parameter Maximum Units 5.5 V 10 V 3 μA 1.0 V IPP = 10A, tp = 8/20μs Ground to Pin 6 3 V VC IPP = 16A, tp = 8/20μs Pin 6 to Ground 12.5 V Cj VR = 0V, f = 1MHz Pin 6 to GN D 275 pF Symbol Conditions Reverse Stand-Off Voltage VRWM Pin 6 to GN D Reverse Breakdown Voltage V BR It = 1mA Pin 6 to GN D Reverse Leakage Current IR VRWM = 5.5V Pin 6 to GN D Forward Voltage VF If = 10mA GN D to Pin 6 Forward Clamping Voltage VF Clamping Voltage Junction Capacitance © 2008 Semtech Corp. 4 Minimum 6 0.6 Typical 8 www.semtech.com RClamp0854P PROTECTION PRODUCTS Typical Characteristics Non-Repetitive Peak Pulse Power vs. Pulse Time Power Derating Curve 10 110 % of Rated Power or PI P Peak Pulse Power - PPP (kW) 100 1 0.1 90 80 70 60 50 40 30 20 10 0 0.01 0.1 1 10 100 0 1000 25 50 110 Waveform Parameters: tr = 8µs td = 20µs 100 90 PP Percent of I 50 td = IPP/2 30 20 10 0 0 5 10 15 150 35 e-t 40 125 40 Clamping Voltage - VC (V) 80 60 100 Clamping Voltage vs. Peak Pulse Current (Pin 1, 2, or 3 to GND) Pulse Waveform 70 75 Ambient Temperature - TA (oC) Pulse Duration - tp (us) 20 25 30 25 20 15 Waveform Parameters: tr = 8μs td = 20μs 10 5 30 0 Time (µs) 0 0.5 1 1.5 2 2.5 3 3.5 4 Peak Pulse Current - IPP (A) Forward Voltage vs. Peak Pulse Current (Pin GND to Pin 6) Clamping Voltage vs. Peak Pulse Current (Pin 6 to GND) 11 3.5 10 3 8 Forward Voltage - VF (V) Clamping Voltage - VC (V) 9 7 6 5 4 3 Waveform Parameters: tr = 8μs td = 20μs 2 1 2.5 2 1.5 Waveform Parameters: tr = 8μs td = 20μs 1 0.5 0 0 0 5 © 2008 Semtech Corp. 10 Peak Pulse Current - IPP (A) 15 20 0 5 5 10 Forward Current - IF (A) 15 20 www.semtech.com RClamp0854P PROTECTION PRODUCTS Typical Characteristics Normalized Capacitance vs. Reverse Voltage (Pin 1, 2, or 3 to Gnd) Insertion Loss S21 (Pin 1, 2, or 3 to Gnd) CH1 S21 2 1.8 6 dB / REF 0 dB 1: -0.086 dB 900 MHz 1.6 3 0 dB 1 1.4 CJ(VR) / CJ(VR=0) LOG f = 1MHz 2: -0.0336 dB 1.8 GHz 2 3: -0.126 dB 2.5 GHz -6 dB 1.2 -12 dB 1 -18 dB 0.8 0.6 -24 dB 0.4 -30 dB 0.2 -36 dB 0 0 1 2 3 Reverse Voltage - VR (V) 4 -42 dB 5 -48 dB 1 MHz START . 030 MHz 10 MHz 100 MHz 3 1 GHz GHz STOP 3 000. 000000 MHz Analog Crosstalk CH1 S21 LOG 20 dB/REF 0 dB START . 030 MHz © 2008 Semtech Corp. STOP 3000. 000000 MHz 6 www.semtech.com RClamp0854P PROTECTION PRODUCTS Applications Information Figure 1- Pin Configuration & Circuit Diagram Device Connection Options for Protecting One USB Port USB Data and ID lines are connected at pins 1, 2, and 3. These inputs are referenced to an internal 5 volt TVS protection device. When the voltage on these lines exceed 5 volts, the TVS will conduct. Pin 6 is connected to the USB voltage bus (VBus). This device will conduct when the voltage on the bus exceeds 5.5 volts. The center tab is connected to ground. The path length should also be kept as short as possible to minimize parasitic inductance. For best results, multiple micro-vias are recommended to the ground plane. 6 1 2 3 5.5V 5.5V GND Protecting USB Interfaces VBus DM DP USB ID GND 5 The RClamp0854P is optimized for use on systems that utilize the USB interface for battery charging. Low capacitance protection is provided for the USB data (DM, DP) and USB ID pins. The maximum capacitance on these lines is <1pF for maximum signal integrity. All three lines are referenced to an internal 5 volt TVS device. A separate 5.5 volt TVS device is used for protection of the USB voltage bus. This allows battery charging without signal clipping. A typical example is shown in Figure 2. 4 3 2 1 1 Mini USB Gnd Figure 2 - USB OTG Protection © 2008 Semtech Corp. 7 www.semtech.com RClamp0854P PROTECTION PRODUCTS Applications Information - Spice Model VBus D2 D4 D3 I/O D1 RClamp0854P Spice Model R Clamp0854P Spice Parameters © 2008 Semtech Corp. Parameter Unit D1 D2 D3 D4 IS Amp 1E-20 1E-20 2E-12 2.93E-12 BV Volt 100 100 9.36 8.3 VJ Volt 0.7 0.7 0.6 0.7 RS Ohm 0.458 1.0 2.6 0.157 IB V Amp 1E-3 1E-3 1E-3 1E-3 CJO Farad 0.3E-12 0.3E-12 56E-12 212E-12 TT sec 2.541E-9 2.541E-9 2.541E-9 2.541E-9 M -- 0.01 0.01 0.23 0.28 N -- 1.1 1.1 1.1 1.1 EG eV 1.11 1.11 1.11 1.11 8 www.semtech.com RClamp0854P PROTECTION PRODUCTS Outline Drawing - SLP1616P6 A D PIN 1 INDICATOR (LASER MARK) B E DIM A SEATING PLANE aaa C A2 A A1 A2 b D D1 E E1 e L N aaa bbb C A1 D1 1 2 LxN E/2 E1 DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX .020 .023 .026 0.00 .001 .002 (.005) .008 .010 .012 .059 .063 .067 .041 .047 .051 .059 .063 .067 .010 .016 .020 .020 BSC .010 .013 .016 6 .003 .004 0.50 0.58 0.65 0.00 0.03 0.05 (0.13) 0.20 0.25 0.30 1.50 1.60 1.70 1.05 1.20 1.30 1.50 1.60 1.70 0.25 0.40 0.50 0.50 BSC 0.25 0.33 0.40 6 0.08 0.10 N bxN bbb e C A B D/2 NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. Land Pattern - SLP1616P6 P X DIMENSIONS Z H G DIM C G H K P X Y Z (C) Y INCHES .060 .035 .018 .051 .020 .012 .025 .085 MILLIMETERS 1.52 0.89 0.45 1.30 0.50 0.30 0.63 2.15 K NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. 3. THERMAL VIAS IN THE LAND PATTERN OF THE EXPOSED PAD SHALL BE CONNECTED TO A SYSTEM GROUND PLANE. FAILURE TO DO SO MAY COMPROMISE THE THERMAL AND/OR FUNCTIONAL PERFORMANCE OF THE DEVICE. © 2008 Semtech Corp. 9 www.semtech.com RClamp0854P PROTECTION PRODUCTS Marking Ordering Information 0854P YW Part Number Lead Finish Qty per Reel R eel Size RClamp 0854P.TCT Pb Free 3,000 7 Inch RailClamp and RClamp are marks of Semtech Corporation YW = Two character Date Code Tape and Reel Specification Device Orientation in Tape Pin 1 in upper left towards sprocket holes A0 1.78 +/-0.10 mm B0 K0 1.78 +/-0.10 mm Tape Width B, (Max) D 8 mm 4.2 mm 1.5 + 0.1 mm - 0.0 mm ) 0.69 +/-0.10 mm D1 E 0.5 mm ±0.05 1.750±.10 mm F K (MAX) P P0 P2 T(MAX) 3.5±0.05 mm 2.4 mm 4.0±0.1 mm 4.0±0.1 mm 2.0±0.05 mm 0.4 mm W 8.0 mm + 0.3 mm - 0.1 mm Contact Information Semtech Corporation Protection Products Division 200 Flynn Rd., Camarillo, CA 93012 Phone: (805)498-2111 FAX (805)498-3804 © 2008 Semtech Corp. 10 www.semtech.com