AMD AM29PDL129H8VKI

Am29PDL129H
Data Sheet
RETIRED
PRODUCT
This product has been retired and is not available for designs. For new and current designs,
S29PL129J supersedes Am29PDL129H and is the factory-recommended migration path. Please refer
to the S29PL129J datasheet for specifications and ordering information. Availability of this document
is retained for reference and historical purposes only.
July 2003
The following document specifies Spansion memory products that are now offered by both Advanced
Micro Devices and Fujitsu. Although the document is marked with the name of the company that
originally developed the specification, these products will be offered to customers of both AMD and
Fujitsu.
Continuity of Specifications
There is no change to this datasheet as a result of offering the device as a Spansion product. Any
changes that have been made are the result of normal datasheet improvement and are noted in the
document revision summary, where supported. Future routine revisions will occur when appropriate, and changes will be noted in a revision summary.
Continuity of Ordering Part Numbers
AMD and Fujitsu continue to support existing part numbers beginning with “Am” and “MBM”. To order
these products, please use only the Ordering Part Numbers listed in this document.
For More Information
Please contact your local AMD or Fujitsu sales office for additional information about Spansion
memory solutions.
Publication Number 26842
Revision B
Amendment +3
Issue Date November 2, 2005
THIS PAGE LEFT INTENTIONALLY BLANK.
Am29PDL129H
128 Megabit (8 M x 16-Bit) CMOS 3.0 Volt-only, Page Mode
Simultaneous Read/Write Flash Memory with Enhanced
VersatileIOTM Control and Dual Chip Enable Inputs
This product has been retired and is not available for designs. For new and current designs, S29PL129J supersedes Am29PDL129H and is the factory-recommended migration path. Please refer to the S29PL129J datasheet for specifications and ordering information. Availability of this document is retained for reference
and historical purposes only.
DISTINCTIVE CHARACTERISTICS
ARCHITECTURAL ADVANTAGES
■ 128 Mbit Page Mode device
— Page size of 8 words: Fast page read access from random
locations within the page
■ Dual Chip Enable inputs
— Two CE# inputs control selection of each half of the memory
space
■ Single power supply operation
— Full Voltage range: 2.7 to 3.6 volt read, erase, and program
operations for battery-powered applications
■ Simultaneous Read/Write Operation
— Data can be continuously read from one bank while
executing erase/program functions in another bank
— Zero latency switching from write to read operations
— 4 separate banks, with up to two simultaneous operations
per device
— Bank 1A: 48 Mbit (32 Kw x 96)
— Bank 1B: 16 Mbit (4 Kw x 8 and 32 Kw x 31)
— Bank 2A: 16 Mbit (4 Kw x 8 and 32 Kw x 31)
— Bank 2B: 48 Mbit (32 Kw x 96)
■ Enhanced VersatileI/O
(VIO) Control
— Output voltage generated and input voltages tolerated on all
control inputs and I/Os is determined by the voltage on the
VIO pin
— VIO options at 1.8 V and 3 V I/O
TM
■ SecSi
SOFTWARE FEATURES
■ Software command-set compatible with JEDEC 42.4
standard
— Backward compatible with Am29F and Am29LV families
■ CFI (Common Flash Interface) complaint
— Provides device-specific information to the system, allowing
host software to easily reconfigure for different Flash devices
■ Erase Suspend / Erase Resume
— Suspends an erase operation to allow read or program
operations in other sectors of same bank
■ Unlock Bypass Program command
■ FlexBank Architecture
TM
— 45 mA active read current
— 15 mA program/erase current
— 1 µA typical standby mode current
(Secured Silicon) Sector region
— Up to 128 words accessible through a command sequence
— Up to 64 factory-locked words
— Up to 64 customer-lockable words
— Reduces overall programming time when issuing multiple
program command sequences
HARDWARE FEATURES
■ Ready/Busy# pin (RY/BY#)
— Provides a hardware method of detecting program or erase
cycle completion
■ Hardware reset pin (RESET#)
— Hardware method to reset the device to reading array data
■ WP#/ACC (Write Protect/Acceleration) input
— At VIL, hardware level protection for the first and last two 4K
word sectors.
— At VIH, allows removal of sector protection
— At VHH, provides accelerated programming in a factory
setting
■ Persistent Sector Protection
■ Manufactured on 0.13 µm process technology
— A command sector protection method to lock combinations
of individual sectors and sector groups to prevent program or
erase operations within that sector
■ 20-year data retention at 125°C
— Sectors can be locked and unlocked in-system at VCC level
■ Both top and bottom boot blocks in one device
■ Minimum 1 million erase cycle guarantee per sector
PERFORMANCE CHARACTERISTICS
■ High Performance
— Page access times as fast as 20 ns
— Random access times as fast as 55 ns
■ Power consumption (typical values at 10 MHz)
■ Password Sector Protection
— A sophisticated sector protection method to lock
combinations of individual sectors and sector groups to
prevent program or erase operations within that sector using
a user-defined 64-bit password
■ Package options
— 80-ball Fine-pitch BGA
— Multi Chip Packages (MCP)
Publication Number: 26842 Rev: B Amendment/ +3
Issue Date: November 2, 2005
GENERAL DESCRIPTION
The Am29PDL129H is a 128 Mbit, 3.0 volt-only Page Mode
and Simultaneous Read/Write Flash memory device organized as 8 Mwords. The device is offered in an 80-ball Finepitch BGA package, and various multi-chip packages. The
word-wide data (x16) appears on DQ15-DQ0. This device
can be programmed in-system or in standard EPROM programmers. A 12.0 V VPP is not required for write or erase operations.
The device offers fast page access times of 20 to 30 ns, with
corresponding random access times of 55 to 85 ns, respectively, allowing high speed microprocessors to operate without wait states. To eliminate bus contention the device has
separate chip enable (CE1#, CE2#), write enable (WE#) and
output enable (OE#) controls. Dual Chip Enables allow access to two 64 Mbit partitions of the 128 Mbit memory space.
Simultaneous Read/Write Operation with
Zero Latency
The Simultaneous Read/Write architecture provides simultaneous operation by dividing the memory space into 4
banks, which can be considered to be four separate memory
arrays as far as certain operations are concerned. The device can improve overall system performance by allowing a
host system to program or erase in one bank, then immediately and simultaneously read from another bank with zero
latency (with two simultaneous operations operating at any
one time). This releases the system from waiting for the
completion of a program or erase operation, greatly improving system performance.
The device can be organized in both top and bottom sector
configurations. The banks are organized as follows:
Chip Enable Configuration
CE1# Control
CE2# Control
Bank 1A
48 Mbit (32 Kw x 96)
Bank 2A
16 Mbit (4 Kw x 8 and 32 Kw x 31)
Bank 1B
16 Mbit (4 Kw x 8 and 32 Kw x 31)
Bank 2B
48 Mbit (32 Kw x 96)
Page Mode Features
The page size is 8 words. After initial page access is accomplished, the page mode operation provides fast read access
speed of random locations within that page.
Standard Flash Memory Features
The device requires a single 3.0 volt power supply (2.7 V
to 3.6 V or 2.7 V to 3.3 V) for both read and write functions.
Internally generated and regulated voltages are provided for
the program and erase operations.
The device is entirely command set compatible with the
JEDEC 42.4 single-power-supply Flash standard. Commands are written to the command register using standard
microprocessor write timing. Register contents serve as inputs to an internal state-machine that controls the erase and
programming circuitry. Write cycles also internally latch addresses and data needed for the programming and erase
operations. Reading data out of the device is similar to reading from other Flash or EPROM devices.
Device programming occurs by executing the program command sequence. The Unlock Bypass mode facilitates faster
programming times by requiring only two write cycles to program data instead of four. Device erasure occurs by executing the erase command sequence.
The host system can detect whether a program or erase operation is complete by reading the DQ7 (Data# Polling) and
DQ6 (toggle) status bits. After a program or erase cycle has
been completed, the device is ready to read array data or accept another command.
The sector erase architecture allows memory sectors to be
erased and reprogrammed without affecting the data contents of other sectors. The device is fully erased when
shipped from the factory.
Hardware data protection measures include a low VCC detector that automatically inhibits write operations during
power transitions. The hardware sector protection feature
disables both program and erase operations in any combination of sectors of memory. This can be achieved in-system or
via programming equipment.
The Erase Suspend/Erase Resume feature enables the
user to put erase on hold for any period of time to read data
from, or program data to, any sector that is not selected for
erasure. True background erase can thus be achieved. If a
read is needed from the SecSi Sector area (One Time Program area) after an erase suspend, then the user must use
the proper command sequence to enter and exit this region.
The device offers two power-saving features. When addresses have been stable for a specified amount of time, the
device enters the automatic sleep mode. The system can
also place the device into the standby mode. Power consumption is greatly reduced in both these modes.
AMD’s Flash technology combined years of Flash memory
manufacturing experience to produce the highest levels of
quality, reliability and cost effectiveness. The device electrically erases all bits within a sector simultaneously via
Fowler-Nordheim tunneling. The data is programmed using
hot electron injection.
Note: The next-generation S29PL129J will have a different bank configuration, as follows:
Chip Enable Configuration
2
CE1# Control
CE2# Control
Bank 1A
16 Mbit (4 Kw x 8 and 32 Kw x 31)
Bank 2A
48 Mbit (32 Kw x 96)
Bank 1B
48 Mbit (32 Kw x 96)
Bank 2B
16 Mbit (4 Kw x 8 and 32 Kw x 31)
Am29PDL129H
November 2, 2005
TABLE OF CONTENTS
Product Selector Guide . . . . . . . . . . . . . . . . . . . . . 5
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Simultaneous Operation Block Diagram . . . . . . . 6
Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . 7
Pin Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Logic Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . 9
Device Bus Operations . . . . . . . . . . . . . . . . . . . . 10
Table 1. Am29PDL129H Device Bus Operations ...........................10
Random Read (Non-Page Read) ........................................... 10
Page Mode Read .................................................................... 10
Table 2. Page Select .......................................................................10
Simultaneous Operation ......................................................... 10
Table 3. Bank Select .......................................................................11
Table 4. Am29PDL129H Sector Architecture ..................................12
Table 5. Addresses .......................................................................19
Table 6. Autoselect Codes (High Voltage Method) ........................19
Table 7. Am29PDL129H Boot Sector/Sector Block Addresses for
Protection/Unprotection
CE1# Control ...................................................................................20
Table 8. Am29PDL129H Boot Sector/Sector Block Addresses for
Protection/Unprotection
CE2# Control ...................................................................................20
Table 9. Sector Protection Schemes ...............................................21
Write Protect (WP#) ................................................................ 21
Persistent Protection Bit Lock ................................................. 21
High Voltage Sector Protection .............................................. 21
Figure 1. ......................................................................................... 21
Temporary Sector Unprotect .................................................. 21
Figure 2. ......................................................................................... 21
Flash Memory Region ............................................................ 21
Factory-Locked Area (64 words) ............................................ 21
Customer-Lockable Area (64 words) ...................................... 22
Figure 3. SecSi Sector Protection Algorithm................................... 23
SecSi Sector Protection Bits ................................................... 24
Figure 4. SecSi Sector Protect Verify.............................................. 24
Common Flash Memory Interface (CFI) . . . . . . . 24
Command Definitions . . . . . . . . . . . . . . . . . . . . . 27
Enter /Exit Command Sequence ............................................ 27
PPB Lock Bit Status .............................................................. 27
Table 14. Memory Array Command Definitions ............................. 28
Table 15. Sector Protection Command Definitions ........................ 29
Absolute Maximum Ratings. . . . . . . . . . . . . . . . . 30
Figure 6. Maximum Negative Overshoot Waveform ...................... 30
Figure 7. Maximum Positive Overshoot Waveform........................ 30
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 31
Test Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 8. Test Setup, VIO = 2.7 – 3.6 V........................................ 32
Figure 9. Input Waveforms and Measurement Levels ................... 32
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 33
CE1#/CE2# Timing ................................................................. 33
Figure 10. Timing Diagram for Alternating Between CE1# and CE2#
Control............................................................................................ 33
Read-Only Operations ........................................................... 33
Figure 11. Read Operation Timings ............................................... 34
Figure 12. Page Read Operation Timings...................................... 34
Hardware Reset (RESET#) .................................................... 35
Figure 13. Reset Timings ............................................................... 35
Erase and Program Operations .............................................. 36
Figure 14. Program Operation Timings..........................................
Figure 15. Accelerated Program Timing Diagram..........................
Figure 16. Chip/Sector Erase Operation Timings ..........................
Figure 17. Back-to-back Read/Write Cycle Timings ......................
Figure 18. Data# Polling Timings (During Embedded Algorithms).
Figure 19. Toggle Bit Timings (During Embedded Algorithms)......
Figure 20. DQ2 vs. DQ6.................................................................
37
37
38
39
39
40
40
Temporary Sector Unprotect .................................................. 41
Figure 21. Temporary Sector Unprotect Timing Diagram .............. 41
Figure 22. Sector/Sector Block Protect and Unprotect Timing Diagram
42
Alternate CE# Controlled Erase and Program Operations ..... 43
Figure 23. Alternate CE# Controlled Write (Erase/Program)
Operation Timings.......................................................................... 44
Erase And Programming Performance. . . . . . . .
Latchup Characteristics . . . . . . . . . . . . . . . . . . . .
BGA Ball Capacitance . . . . . . . . . . . . . . . . . . . . .
Data Retention. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Revision Summary . . . . . . . . . . . . . . . . . . . . . . . .
45
45
45
45
46
Figure 5. ......................................................................................... 27
November 2, 2005
Am29PDL129H
3
PRODUCT SELECTOR GUIDE
Part Number
Speed Option
Am29PDL129H
VCC, VIO = 2.7–3.6 V
53
63
VCC = 2.7–3.6 V, VIO = 1.65–1.95 V
68
Max Access Time, ns (tACC)
55
Max CE# Access, ns (tCE)
60
65
65
Max Page Access, ns (tPACC)
20
88
85
70
25
30
30
Max OE# Access, ns (tOE)
BLOCK DIAGRAM
DQ15–DQ0
RY/BY# (See Note)
VCC
VSS
Sector
Switches
VIO
RESET#
Input/Output
Buffers
Erase Voltage
Generator
WE#
State
Control
Command
Register
PGM Voltage
Generator
Chip Enable
Output Enable
Logic
CE1#
CE2#
OE#
Y-Decoder
A21–A3
Y-Gating
Timer
Address Latch
VCC Detector
Data Latch
X-Decoder
Cell Matrix
A2–A0
Note:RY/BY# is an open drain output.
4
Am29PDL129H
November 2, 2005
SIMULTANEOUS OPERATION BLOCK DIAGRAM
VCC
VSS
OE#
CE1#=L
CE2#=H
Mux
Bank 1A
Bank 1B
X-Decoder
A21–A0
RESET#
WE#
CE1#
CE2#
WP#/ACC
STATE
CONTROL
&
COMMAND
REGISTER
Status
DQ15–DQ0
Control
Mux
DQ15–DQ0
CE1#=H
CE2#=L
X-Decoder
Bank 2A Address
Bank 2A
X-Decoder
Bank 2B Address
Y-gate
A21–A0
DQ0–DQ15
A21–A0
DQ15–DQ0
Bank 1B Address
DQ15–DQ0
RY/BY#
DQ15–DQ0
A21–A0
X-Decoder
Y-gate
Bank 1A Address
A21–A0
Bank 2B
Mux
November 2, 2005
Am29PDL129H
5
CONNECTION DIAGRAMS
80-Ball Fine-pitch BGA
Top View, Balls Facing Down
A8
B8
C8
D8
E8
F8
G8
H8
J8
K8
L8
M8
NC
NC
NC
NC
NC
VIO
VSS
NC
NC
NC
NC
NC
A7
B7
C7
D7
E7
F7
G7
H7
J7
K7
L7
M7
NC
NC
A13
A12
A14
A15
A16
NC
DQ15
VSS
NC
NC
C6
D6
E6
F6
G6
H6
J6
K6
A9
A8
A10
A11
DQ7
DQ14
DQ13
DQ6
C5
D5
E5
F5
G5
H5
J5
K5
WE#
RESET#
A21
A19
DQ5
DQ12
VCC
DQ4
C4
D4
E4
F4
G4
H4
J4
K4
A18
A20
DQ2
DQ10
DQ11
DQ3
RY/BY# WP#/ACC
C3
D3
E3
F3
G3
H3
J3
K3
A7
A17
A6
A5
DQ0
DQ8
DQ9
DQ1
A2
B2
C2
D2
E2
F2
G2
H2
J2
K2
L2
M2
NC
NC
A3
A4
A2
A1
A0
CE1#
OE#
VSS
NC
NC
A1
B1
C1
D1
E1
F1
G1
H1
J1
K1
L1
M1
NC
NC
NC
NC
NC
NC
CE2#
VIO
NC
NC
NC
NC
Note: On S29PL129J, G1= NC and J1= CE2#
6
Am29PDL129H
November 2, 2005
PIN DESCRIPTION
A21–A0
=
the device is either executing an embedded algorithm or the device is
executing a hardware reset operation.
22-bit address bus for 2 x 64 Mb device. A9 supports 12 V autoselect inputs.
DQ15–DQ0 =
16-bit data inputs/outputs/float
CE1#, CE2# =
Chip Enable Inputs. CE1# controls
the 64 Mb in Banks 1A and 1B.
CE2# controls the 64 Mb in Banks
2A and 2B.
OE#
=
Output Enable Input
WE#
=
Write Enable
VSS
=
Device Ground
NC
=
Pin Not Connected Internally
RY/BY#
=
Ready/Busy output and open drain.
When RY/BY#= VIH, the device is
ready to accept read operations and
commands. When RY/BY#= VOL,
WP#/ACC
=
Write Protect/Acceleration Input.
When WP/ACC#= VIL, the highest
and lowest two 4K-word sectors are
write protected regardless of other
sector protection configurations.
When WP/ACC#= VIH, these sector
are unprotected unless the DYB or
PPB is programmed. When WP/
ACC#= 12V, program and erase operations are accelerated.
VIO
=
Input/Output Buffer Power Supply
(1.65 V to 1.95 V or 2.7 V to 3.6 V)
VCC
=
Chip Power Supply
(2.7 V to 3.6 V)
RESET#
=
Hardware Reset Pin
LOGIC SYMBOL
22
A21–A0
16
DQ15–DQ0
CE1#
CE2#
OE#
WE#
WP#/ACC
RESET#
RY/BY#
VIO (VCCQ)
November 2, 2005
Am29PDL129H
7
ORDERING INFORMATION
Standard Products
AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is
formed by a combination of the following:
Am29PDL129
H
53
VK
I
OPTIONAL PROCESSING
Blank = Standard Processing
N
= 16-byte ESN devices
(Contact an AMD representative for more information)
TEMPERATURE RANGE
I
= Industrial (–40°C to +85°C)
PACKAGE TYPE
VK
= 80-Ball Fine-pitch Ball Grid Array
0.8 mm pitch, 11.5 x 9 mm package (VBB080)
SPEED OPTION
See Product Selector Guide and Valid Combinations
PROCESS TECHNOLOGY
H = 0.13 µm
DEVICE NUMBER/DESCRIPTION
Am29PDL129H
128 Megabit (8 M x 16-Bit) CMOS Flash Memory
3.0 Volt-only Read, Program, and Erase
Dual Chip Enable Inputs
Valid Combinations
Valid Combinations list configurations planned to be supported in
volume for this device. Consult the local AMD sales office to confirm availability of specific valid combinations and to check on
newly released combinations.
Note: For the Am29PDL129H, the last digit of the speed grade
specifies the VIO range of the device. Speed grades ending in 3 (for
example: 53, 63) indicate a 3 Volt VIO range. Speed grades ending in 8
(for example: 68, 88) indicate a 1.8 Volt VIO range. Contact AMD or
Fujitsu for availability of 1.8V VIO range devices.
Valid Combinations for BGA Packages
Order Number
Package Marking
Speed
(ns)
VIO Range
Am29PDL129H53
PD129H53V
55
2.7–3.6 V
Am29PDL129H63
PD129H63V
65
2.7–3.6 V
65
1.65–1.95 V
85
1.65–1.95 V
Am29PDL129H68
Am29PDL129H88
8
VKI
PD129H68V
PD129H88V
I
Am29PDL129H
November 2, 2005
DEVICE BUS OPERATIONS
Table 1.
Am29PDL129H Device Bus Operations
OE#
WE#
RESET#
WP#/ACC
Addresses
(A21–A0)
DQ15–
DQ0
L
H
H
X
AIN
DOUT
H
L
H
X
(Note 2)
AIN
DIN
VIO ±
0.3 V
X
X
VIO ±
0.3 V
X
X
High-Z
L
L
H
H
H
X
X
High-Z
Reset
X
X
X
X
L
X
X
High-Z
Temporary Sector Unprotect (High
Voltage)
X
X
X
X
VID
X
AIN
DIN
Operation
CE1#
CE2#
L
H
H
L
L
H
H
L
VIO±
0.3 V
Output Disable
Read
Write
Standby
Legend: L = Logic Low = VIL, H = Logic High = VIH, VID = 11.5–12.5 V, VHH = 8.5–9.5 V, X = Don’t Care, SA = Sector Address,
AIN = Address In, DIN = Data In, DOUT = Data Out
Notes:
1. The sector protect and sector unprotect functions may also be implemented via programming equipment. .
2. WP#/ACC must be high when writing to sectors SA1-133, SA1-134, SA2-0, or SA2-1.
Random Read (Non-Page Read)
Table 2.
Address access time (tACC) is equal to the delay from
stable addresses to valid output data. The chip enable
access time (t CE ) is the delay from the stable addresses and stable CE# to valid data at the output inputs. The output enable access time is the delay from
the falling edge of the OE# to valid data at the output
inputs (assuming the addresses have been stable for
at least tACC–tOE time).
Page Mode Read
The device is capable of fast page mode read and is
compatible with the page mode Mask ROM read operation. This mode provides faster read access speed
for random locations within a page. Address bits A21–
A3 select an 8-word page, and address bits A2–A0 select a specific work within that page. This is an asynchronous operation with the microprocessor supplying
the specific word location.
The random or initial page access is tACC or tCE and
subsequent page read accesses (as long as the locations specified by the microprocessor fall within that
page) are t PACC. When CE1# and CE2# are deasserted (CE1#=CE2#=VIH), the reassertion of CE1# or
CE2# for subsequent access has access time of tACC
or tCE. Here again, CE1#/CE2# selects the device and
OE# is the output control and should be used to gate
data to the output inputs if the device is selected. Fast
page mode accesses are obtained by keeping A21–
A3 constant and changing A2 to A0 to select the specific word within that page.
November 2, 2005
Page Select
Word
A2
A1
A0
Word 0
0
0
0
Word 1
0
0
1
Word 2
0
1
0
Word 3
0
1
1
Word 4
1
0
0
Word 5
1
0
1
Word 6
1
1
0
Word 7
1
1
1
Simultaneous Operation
In addition to the conventional features (read, program, erase-suspend read, and erase-suspend program), the device is capable of reading data from one
bank of memory while a program or erase operation is
in progress in another bank of memory (simultaneous
operation), The bank can be selected by bank addresses (A21–A20) with zero latency.
The simultaneous operation can execute multi-function mode in the same bank.
Am29PDL129H
9
Table 3.
Bank Select
Bank
CE1#
CE2#
A21–A20
Bank 1A
0
1
00, 01, 10
Bank 1B
0
1
11
10
Bank 2A
1
0
00
Bank 2B
1
0
01, 10, 11
Am29PDL129H
November 2, 2005
Table 4.
Bank 1A
Bank
Am29PDL129H Sector Architecture
Sector
CE1#
CE2#
Sector Address (A21A12)
Sector Size
(Kwords)
Address Range (x16)
SA1-0
0
1
0000000XXX
32
000000h–007FFFh
SA1-1
0
1
0000001XXX
32
008000h–00FFFFh
SA1-2
0
1
0000010XXX
32
010000h–017FFFh
SA1-3
0
1
0000011XXX
32
018000h–01FFFFh
SA1-4
0
1
0000100XXX
32
020000h–027FFFh
SA1-5
0
1
0000101XXX
32
028000h–02FFFFh
SA1-6
0
1
0000110XXX
32
030000h–037FFFh
SA1-7
0
1
0000111XXX
32
038000h–03FFFFh
SA1-8
0
1
0001000XXX
32
040000h–047FFFh
SA1-9
0
1
0001001XXX
32
048000h–04FFFFh
SA1-10
0
1
0001010XXX
32
050000h–057FFFh
SA1-11
0
1
0001011XXX
32
058000h–05FFFFh
SA1-12
0
1
0001100XXX
32
060000h–067FFFh
SA1-13
0
1
0001101XXX
32
068000h–06FFFFh
SA1-14
0
1
0001110XXX
32
070000h–077FFFh
SA1-15
0
1
0001111XXX
32
078000h–07FFFFh
SA1-16
0
1
0010000XXX
32
080000h–087FFFh
SA1-17
0
1
0010001XXX
32
088000h–08FFFFh
SA1-18
0
1
0010010XXX
32
090000h–097FFFh
SA1-19
0
1
0010011XXX
32
098000h–09FFFFh
SA1-20
0
1
0010100XXX
32
0A0000h–0A7FFFh
SA1-21
0
1
0010101XXX
32
0A8000h–0AFFFFh
SA1-22
0
1
0010110XXX
32
0B0000h–0B7FFFh
SA1-23
0
1
0010111XXX
32
0B8000h–0BFFFFh
SA1-24
0
1
0011000XXX
32
0C0000h–0C7FFFh
SA1-25
0
1
0011001XXX
32
0C8000h–0CFFFFh
SA1-26
0
1
0011010XXX
32
0D0000h–0D7FFFh
SA1-27
0
1
0011011XXX
32
0D8000h–0DFFFFh
SA1-28
0
1
0011100XXX
32
0E0000h–0E7FFFh
SA1-29
0
1
0011101XXX
32
0E8000h–0EFFFFh
SA1-30
0
1
0011110XXX
32
0F0000h–0F7FFFh
SA1-31
0
1
0011111XXX
32
0F8000h–0FFFFFh
SA1-32
0
1
0100000XXX
32
100000h–107FFFh
SA1-33
0
1
0100001XXX
32
108000h–10FFFFh
SA1-34
0
1
0100010XXX
32
110000h–117FFFh
SA1-35
0
1
0100011XXX
32
118000h–11FFFFh
SA1-36
0
1
0100100XXX
32
120000h–127FFFh
SA1-37
0
1
0100101XXX
32
128000h–12FFFFh
November 2, 2005
Am29PDL129H
11
Table 4.
Bank 1A
Bank
12
Am29PDL129H Sector Architecture
Sector
CE1#
CE2#
Sector Address (A21A12)
Sector Size
(Kwords)
SA1-38
0
1
0100110XXX
32
130000h–137FFFh
SA1-39
0
1
0100111XXX
32
138000h–13FFFFh
SA1-40
0
1
0101000XXX
32
140000h–147FFFh
SA1-41
0
1
0101001XXX
32
148000h–14FFFFh
SA1-42
0
1
0101010XXX
32
150000h–157FFFh
SA1-43
0
1
0101011XXX
32
158000h–15FFFFh
SA1-44
0
1
0101100XXX
32
160000h–167FFFh
SA1-45
0
1
0101101XXX
32
168000h–16FFFFh
SA1-46
0
1
0101110XXX
32
170000h–177FFFh
SA1-47
0
1
0101111XXX
32
178000h–17FFFFh
SA1-48
0
1
0110000XXX
32
180000h–187FFFh
SA1-49
0
1
0110001XXX
32
188000h–18FFFFh
SA1-50
0
1
0110010XXX
32
190000h–197FFFh
SA1-51
0
1
0110011XXX
32
198000h–19FFFFh
SA1-52
0
1
0110100XXX
32
1A0000h–1A7FFFh
SA1-53
0
1
0110101XXX
32
1A8000h–1AFFFFh
Address Range (x16)
SA1-54
0
1
0110110XXX
32
1B0000h–1B7FFFh
SA1-55
0
1
0110111XXX
32
1B8000h–1BFFFFh
SA1-56
0
1
0111000XXX
32
1C0000h–1C7FFFh
SA1-57
0
1
0111001XXX
32
1C8000h–1CFFFFh
SA1-58
0
1
0111010XXX
32
1D0000h–1D7FFFh
SA1-59
0
1
0111011XXX
32
1D8000h–1DFFFFh
SA1-60
0
1
0111100XXX
32
1E0000h–1E7FFFh
SA1-61
0
1
0111101XXX
32
1E8000h–1EFFFFh
SA1-62
0
1
0111110XXX
32
1F0000h–1F7FFFh
SA1-63
0
1
0111111XXX
32
1F8000h–1FFFFFh
SA1-64
0
1
1000000XXX
32
200000h–207FFFh
SA1-65
0
1
1000001XXX
32
208000h–20FFFFh
SA1-66
0
1
1000010XXX
32
210000h–217FFFh
SA1-67
0
1
1000011XXX
32
218000h–21FFFFh
SA1-68
0
1
1000100XXX
32
220000h–227FFFh
SA1-69
0
1
1000101XXX
32
228000h–22FFFFh
SA1-70
0
1
1000110XXX
32
230000h–237FFFh
SA1-71
0
1
1000111XXX
32
238000h–23FFFFh
SA1-72
0
1
1001000XXX
32
240000h–247FFFh
SA1-73
0
1
1001001XXX
32
248000h–24FFFFh
SA1-74
0
1
1001010XXX
32
250000h–257FFFh
SA1-75
0
1
1001011XXX
32
258000h–25FFFFh
SA1-76
0
1
1001100XXX
32
260000h–267FFFh
SA1-77
0
1
1001101XXX
32
268000h–26FFFFh
Am29PDL129H
November 2, 2005
Table 4.
Bank 1A
Bank
Am29PDL129H Sector Architecture
Sector
CE1#
CE2#
Sector Address (A21A12)
Sector Size
(Kwords)
SA1-78
0
1
1001110XXX
32
270000h–277FFFh
SA1-79
0
1
1001111XXX
32
278000h–27FFFFh
SA1-80
0
1
1010000XXX
32
280000h–287FFFh
SA1-81
0
1
1010001XXX
32
288000h–28FFFFh
SA1-82
0
1
1010010XXX
32
290000h–297FFFh
SA1-83
0
1
1010011XXX
32
298000h–29FFFFh
SA1-84
0
1
1010100XXX
32
2A0000h–2A7FFFh
SA1-85
0
1
1010101XXX
32
2A8000h–2AFFFFh
Address Range (x16)
SA1-86
0
1
1010110XXX
32
2B0000h–2B7FFFh
SA1-87
0
1
1010111XXX
32
2B8000h–2BFFFFh
SA1-88
0
1
1011000XXX
32
2C0000h–2C7FFFh
SA1-89
0
1
1011001XXX
32
2C8000h–2CFFFFh
SA1-90
0
1
1011010XXX
32
2D0000h–2D7FFFh
SA1-91
0
1
1011011XXX
32
2D8000h–2DFFFFh
SA1-92
0
1
1011100XXX
32
2E0000h–2E7FFFh
SA1-93
0
1
1011101XXX
32
2E8000h–2EFFFFh
SA1-94
0
1
1011110XXX
32
2F0000h–2F7FFFh
SA1-95
0
1
1011111XXX
32
2F8000h–2FFFFFh
November 2, 2005
Am29PDL129H
13
Table 4.
Bank 1B
Bank
14
Am29PDL129H Sector Architecture
Sector
CE1#
CE2#
Sector Address (A21A12)
Sector Size
(Kwords)
SA1-96
0
1
1100000XXX
32
300000h–307FFFh
SA1-97
0
1
1100001XXX
32
308000h–30FFFFh
SA1-98
0
1
1100010XXX
32
310000h–317FFFh
SA1-99
0
1
1100011XXX
32
318000h–31FFFFh
SA1-100
0
1
1100100XXX
32
320000h–327FFFh
SA1-101
0
1
1100101XXX
32
328000h–32FFFFh
SA1-102
0
1
1100110XXX
32
330000h–337FFFh
SA1-103
0
1
1100111XXX
32
338000h–33FFFFh
SA1-104
0
1
1101000XXX
32
340000h–347FFFh
SA1-105
0
1
1101001XXX
32
348000h–34FFFFh
SA1-106
0
1
1101010XXX
32
350000h–357FFFh
SA1-107
0
1
1101011XXX
32
358000h–35FFFFh
SA1-108
0
1
1101100XXX
32
360000h–367FFFh
SA1-109
0
1
1101101XXX
32
368000h–36FFFFh
SA1-110
0
1
1101110XXX
32
370000h–377FFFh
SA1-111
0
1
1101111XXX
32
378000h–37FFFFh
SA1-112
0
1
1110000XXX
32
380000h–387FFFh
SA1-113
0
1
1110001XXX
32
388000h–38FFFFh
SA1-114
0
1
1110010XXX
32
390000h–397FFFh
SA1-115
0
1
1110011XXX
32
398000h–39FFFFh
SA1-116
0
1
1110100XXX
32
3A0000h–3A7FFFh
SA1-117
0
1
1110101XXX
32
3A8000h–3AFFFFh
SA1-118
0
1
1110110XXX
32
3B0000h–3B7FFFh
SA1-119
0
1
1110111XXX
32
3B8000h–3BFFFFh
SA1-120
0
1
1111000XXX
32
3C0000h–3C7FFFh
SA1-121
0
1
1111001XXX
32
3C8000h–3CFFFFh
SA1-122
0
1
1111010XXX
32
3D0000h–3D7FFFh
SA1-123
0
1
1111011XXX
32
3D8000h–3DFFFFh
SA1-124
0
1
1111100XXX
32
3E0000h–3E7FFFh
SA1-125
0
1
1111101XXX
32
3E8000h–3EFFFFh
SA1-126
0
1
1111110XXX
32
3F0000h–3F7FFFh
SA1-127
0
1
1111111000
4
3F8000h–3F8FFFh
SA1-128
0
1
1111111001
4
3F9000h–3F9FFFh
Address Range (x16)
SA1-129
0
1
1111111010
4
3FA000h–3FAFFFh
SA1-130
0
1
1111111011
4
3FB000h–3FBFFFh
SA1-131
0
1
1111111100
4
3FC000h–3FCFFFh
SA1-132
0
1
1111111101
4
3FD000h–3FDFFFh
SA1-133
0
1
1111111110
4
3FE000h–3FEFFFh
SA1-134
0
1
1111111111
4
3FF000h–3FFFFFh
Am29PDL129H
November 2, 2005
Table 4.
Bank 2A
Bank
Am29PDL129H Sector Architecture
Sector
CE1#
CE2#
Sector Address (A21A12)
Sector Size
(Kwords)
Address Range (x16)
SA2-0
1
0
0000000000
4
000000h–000FFFh
SA2-1
1
0
0000000001
4
001000h–001FFFh
SA2-2
1
0
0000000010
4
002000h–002FFFh
SA2-3
1
0
0000000011
4
003000h–003FFFh
SA2-4
1
0
0000000100
4
004000h–004FFFh
SA2-5
1
0
0000000101
4
005000h–005FFFh
SA2-6
1
0
0000000110
4
006000h–006FFFh
SA2-7
1
0
0000000111
4
007000h–007FFFh
SA2-8
1
0
0000001XXX
32
008000h–00FFFFh
SA2-9
1
0
0000010XXX
32
010000h–017FFFh
SA2-10
1
0
0000011XXX
32
018000h–01FFFFh
SA2-11
1
0
0000100XXX
32
020000h–027FFFh
SA2-12
1
0
0000101XXX
32
028000h–02FFFFh
SA2-13
1
0
0000110XXX
32
030000h–037FFFh
SA2-14
1
0
0000111XXX
32
038000h–03FFFFh
SA2-15
1
0
0001000XXX
32
040000h–047FFFh
SA2-16
1
0
0001001XXX
32
048000h–04FFFFh
SA2-17
1
0
0001010XXX
32
050000h–057FFFh
SA2-18
1
0
0001011XXX
32
058000h–05FFFFh
SA2-19
1
0
0001100XXX
32
060000h–067FFFh
SA2-20
1
0
0001101XXX
32
068000h–06FFFFh
SA2-21
1
0
0001110XXX
32
070000h–077FFFh
SA2-22
1
0
0001111XXX
32
078000h–07FFFFh
SA2-23
1
0
0010000XXX
32
080000h–087FFFh
SA2-24
1
0
0010001XXX
32
088000h–08FFFFh
SA2-25
1
0
0010010XXX
32
090000h–097FFFh
SA2-26
1
0
0010011XXX
32
098000h–09FFFFh
SA2-27
1
0
0010100XXX
32
0A0000h–0A7FFFh
SA2-28
1
0
0010101XXX
32
0A8000h–0AFFFFh
SA2-29
1
0
0010110XXX
32
0B0000h–0B7FFFh
SA2-30
1
0
0010111XXX
32
0B8000h–0BFFFFh
SA2-31
1
0
0011000XXX
32
0C0000h–0C7FFFh
SA2-32
1
0
0011001XXX
32
0C8000h–0CFFFFh
SA2-33
1
0
0011010XXX
32
0D0000h–0D7FFFh
SA2-34
1
0
0011011XXX
32
0D8000h–0DFFFFh
SA2-35
1
0
0011100XXX
32
0E0000h–0E7FFFh
SA2-36
1
0
0011101XXX
32
0E8000h–0EFFFFh
SA2-37
1
0
0011110XXX
32
0F0000h–0F7FFFh
SA2-38
1
0
0011111XXX
32
0F8000h–0FFFFFh
November 2, 2005
Am29PDL129H
15
Table 4.
Bank 2B
Bank
16
Am29PDL129H Sector Architecture
Sector
CE1#
CE2#
Sector Address (A21A12)
Sector Size
(Kwords)
SA2-39
1
0
0100000XXX
32
100000h–107FFFh
SA2-40
1
0
0100001XXX
32
108000h–10FFFFh
SA2-41
1
0
0100010XXX
32
110000h–117FFFh
SA2-42
1
0
0100011XXX
32
118000h–11FFFFh
SA2-43
1
0
0100100XXX
32
120000h–127FFFh
SA2-44
1
0
0100101XXX
32
128000h–12FFFFh
SA2-45
1
0
0100110XXX
32
130000h–137FFFh
SA2-46
1
0
0100111XXX
32
138000h–13FFFFh
SA2-47
1
0
0101000XXX
32
140000h–147FFFh
SA2-48
1
0
0101001XXX
32
148000h–14FFFFh
SA2-49
1
0
0101010XXX
32
150000h–157FFFh
SA2-50
1
0
0101011XXX
32
158000h–15FFFFh
SA2-51
1
0
0101100XXX
32
160000h–167FFFh
SA2-52
1
0
0101101XXX
32
168000h–16FFFFh
SA2-53
1
0
0101110XXX
32
170000h–177FFFh
SA2-54
1
0
0101111XXX
32
178000h–17FFFFh
SA2-55
1
0
0110000XXX
32
180000h–187FFFh
SA2-56
1
0
0110001XXX
32
188000h–18FFFFh
SA2-57
1
0
0110010XXX
32
190000h–197FFFh
SA2-58
1
0
0110011XXX
32
198000h–19FFFFh
SA2-59
1
0
0110100XXX
32
1A0000h–1A7FFFh
SA2-60
1
0
0110101XXX
32
1A8000h–1AFFFFh
SA2-61
1
0
0110110XXX
32
1B0000h–1B7FFFh
SA2-62
1
0
0110111XXX
32
1B8000h–1BFFFFh
SA2-63
1
0
0111000XXX
32
1C0000h–1C7FFFh
SA2-64
1
0
0111001XXX
32
1C8000h–1CFFFFh
SA2-65
1
0
0111010XXX
32
1D0000h–1D7FFFh
SA2-66
1
0
0111011XXX
32
1D8000h–1DFFFFh
SA2-67
1
0
0111100XXX
32
1E0000h–1E7FFFh
SA2-68
1
0
0111101XXX
32
1E8000h–1EFFFFh
SA2-69
1
0
0111110XXX
32
1F0000h–1F7FFFh
SA2-70
1
0
0111111XXX
32
1F8000h–1FFFFFh
SA2-71
1
0
1000000XXX
32
200000h–207FFFh
SA2-72
1
0
1000001XXX
32
208000h–20FFFFh
SA2-73
1
0
1000010XXX
32
210000h–217FFFh
SA2-74
1
0
1000011XXX
32
218000h–21FFFFh
SA2-75
1
0
1000100XXX
32
220000h–227FFFh
SA2-76
1
0
1000101XXX
32
228000h–22FFFFh
SA2-77
1
0
1000110XXX
32
230000h–237FFFh
SA2-78
1
0
1000111XXX
32
238000h–23FFFFh
Am29PDL129H
Address Range (x16)
November 2, 2005
Table 4.
Bank 2B
Bank
Am29PDL129H Sector Architecture
Sector
CE1#
CE2#
Sector Address (A21A12)
Sector Size
(Kwords)
SA2-79
1
0
1001000XXX
32
240000h–247FFFh
SA2-80
1
0
1001001XXX
32
248000h–24FFFFh
SA2-81
1
0
1001010XXX
32
250000h–257FFFh
SA2-82
1
0
1001011XXX
32
258000h–25FFFFh
SA2-83
1
0
1001100XXX
32
260000h–267FFFh
SA2-84
1
0
1001101XXX
32
268000h–26FFFFh
SA2-85
1
0
1001110XXX
32
270000h–277FFFh
SA2-86
1
0
1001111XXX
32
278000h–27FFFFh
SA2-87
1
0
1010000XXX
32
280000h–287FFFh
SA2-88
1
0
1010001XXX
32
288000h–28FFFFh
SA2-89
1
0
1010010XXX
32
290000h–297FFFh
SA2-90
1
0
1010011XXX
32
298000h–29FFFFh
SA2-91
1
0
1010100XXX
32
2A0000h–2A7FFFh
SA2-92
1
0
1010101XXX
32
2A8000h–2AFFFFh
SA2-93
1
0
1010110XXX
32
2B0000h–2B7FFFh
SA2-94
1
0
1010111XXX
32
2B8000h–2BFFFFh
SA2-95
1
0
1011000XXX
32
2C0000h–2C7FFFh
SA2-96
1
0
1011001XXX
32
2C8000h–2CFFFFh
SA2-97
1
0
1011010XXX
32
2D0000h–2D7FFFh
SA2-98
1
0
1011011XXX
32
2D8000h–2DFFFFh
SA2-99
1
0
1011100XXX
32
2E0000h–2E7FFFh
SA2-100
1
0
1011101XXX
32
2E8000h–2EFFFFh
SA2-101
1
0
1011110XXX
32
2F0000h–2F7FFFh
SA2-102
1
0
1011111XXX
32
2F8000h–2FFFFFh
SA2-103
1
0
1100000XXX
32
300000h–307FFFh
SA2-104
1
0
1100001XXX
32
308000h–30FFFFh
SA2-105
1
0
1100010XXX
32
310000h–317FFFh
SA2-106
1
0
1100011XXX
32
318000h–31FFFFh
SA2-107
1
0
1100100XXX
32
320000h–327FFFh
SA2-108
1
0
1100101XXX
32
328000h–32FFFFh
SA2-109
1
0
1100110XXX
32
330000h–337FFFh
SA2-110
1
0
1100111XXX
32
338000h–33FFFFh
SA2-111
1
0
1101000XXX
32
340000h–347FFFh
SA2-112
1
0
1101001XXX
32
348000h–34FFFFh
SA2-113
1
0
1101010XXX
32
350000h–357FFFh
SA2-114
1
0
1101011XXX
32
358000h–35FFFFh
SA2-115
1
0
1101100XXX
32
360000h–367FFFh
SA2-116
1
0
1101101XXX
32
368000h–36FFFFh
SA2-117
1
0
1101110XXX
32
370000h–377FFFh
SA2-118
1
0
1101111XXX
32
378000h–37FFFFh
November 2, 2005
Am29PDL129H
Address Range (x16)
17
Table 4.
Bank 2B
Bank
Am29PDL129H Sector Architecture
Sector
CE1#
CE2#
Sector Address (A21A12)
Sector Size
(Kwords)
SA2-119
1
0
1110000XXX
32
380000h–387FFFh
SA2-120
1
0
1110001XXX
32
388000h–38FFFFh
SA2-121
1
0
1110010XXX
32
390000h–397FFFh
SA2-122
1
0
1110011XXX
32
398000h–39FFFFh
SA2-123
1
0
1110100XXX
32
3A0000h–3A7FFFh
SA2-124
1
0
1110101XXX
32
3A8000h–3AFFFFh
SA2-125
1
0
1110110XXX
32
3B0000h–3B7FFFh
SA2-126
1
0
1110111XXX
32
3B8000h–3BFFFFh
SA2-127
1
0
1111000XXX
32
3C0000h–3C7FFFh
SA2-128
1
0
1111001XXX
32
3C8000h–3CFFFFh
SA2-129
1
0
1111010XXX
32
3D0000h–3D7FFFh
SA2-130
1
0
1111011XXX
32
3D8000h–3DFFFFh
SA2-131
1
0
1111100XXX
32
3E0000h–3E7FFFh
SA2-132
1
0
1111101XXX
32
3E8000h–3EFFFFh
SA2-133
1
0
1111110XXX
32
3F0000h–3F7FFFh
1
0
1111111XXX
32
3F8000h–3FFFFFh
SA2-134
Table 5.
Am29PDL129H
Addresses
Sector Size
Address Range
128 words
000000h–00007Fh
Factory-Locked Area
64 words
000000h-00003Fh
Customer-Lockable Area
64 words
000040h-00007Fh
Table 6.
Description
Manufacturer ID:
AMD
Device ID
Read
Cycle 1
Read
Cycle 2
Read
Cycle 3
Sector Protection
Verification
Indicator Bit
(DQ7, DQ6)
CE1#
CE2#
L
H
H
L
L
H
H
L
L
H
H
L
L
H
H
L
L
H
H
L
L
H
Autoselect Codes (High Voltage Method)
OE#
WE#
A21
to
A12
L
H
X
L
H
Address Range (x16)
H
X
A10
A9
A8
A7
X
VID
X
L
X
VID
X
L
A6
A5
to
A4
A3
A2
A1
A0
DQ15
to DQ0
L
X
L
L
L
L
0001h
L
L
L
H
227Eh
H
H
H
L
2221h
H
H
H
H
2200h
L
L
L
H
SA
X
VID
X
L
L
L
L
L
H
L
0001h (protected),
0000h (unprotected)
L
H
X
X
VID
X
X
L
X
L
L
H
H
00C0h (factory and
customer locked),
0080h (factory
locked)
L
Legend: L = Logic Low = VIL, H = Logic High = VIH, BA = Bank Address, SA = Sector Address, X = Don’t care. Note: The autoselect codes may also
be accessed in-system via command sequences
Table 7. Am29PDL129H Boot Sector/Sector Block
Addresses for Protection/Unprotection
18
CE1# Control
Sector
Group
A21-12
Sector/Sector Block
Size
SA1-0–SA1-3
00000XXXXX
128 (4x32) Kwords
Am29PDL129H
November 2, 2005
Sector
Group
A21-12
Sector/Sector Block
Size
SA1-4–SA1-7
00001XXXXX
128 (4x32) Kwords
Table 8. Am29PDL129H Boot Sector/Sector Block
Addresses for Protection/Unprotection
CE2# Control
SA1-8–SA1-11
00010XXXXX
128 (4x32) Kwords
SA1-12–SA1-15
00011XXXXX
128 (4x32) Kwords
Sector
Group
A21-12
Sector/Sector Block
Size
SA1-16–SA1-19
00100XXXXX
128 (4x32) Kwords
SA2-0
0000000000
4 Kwords
SA1-20–SA1-23
00101XXXXX
128 (4x32) Kwords
SA2-1
0000000001
4 Kwords
SA1-24–SA1-27
00110XXXXX
128 (4x32) Kwords
SA2-2
0000000010
4 Kwords
SA1-28–SA1-31
00111XXXXX
128 (4x32) Kwords
SA2-3
0000000011
4 Kwords
SA1-32–SA1-35
01000XXXXX
128 (4x32) Kwords
SA2-4
0000000100
4 Kwords
SA1-36–SA1-39
01001XXXXX
128 (4x32) Kwords
SA2-5
0000000101
4 Kwords
SA1-40–SA1-43
01010XXXXX
128 (4x32) Kwords
SA2-6
0000000110
4 Kwords
SA1-44–SA1-47
01011XXXXX
128 (4x32) Kwords
SA2-7
0000000111
4 Kwords
SA1-48–SA1-51
01100XXXXX
128 (4x32) Kwords
SA2-8
0000001XXX
32 Kwords
SA1-52–SA1-55
01101XXXXX
128 (4x32) Kwords
SA2-9
0000010XXX
32 Kwords
SA1-56–SA1-59
01110XXXXX
128 (4x32) Kwords
SA2-10
0000011XXX
32 Kwords
SA1-60–SA1-63
01111XXXXX
128 (4x32) Kwords
SA2-11 - SA2-14
00001XXXXX
128 (4x32) Kwords
SA1-64–SA1-67
10000XXXXX
128 (4x32) Kwords
SA2-15 - SA2-18
00010XXXXX
128 (4x32) Kwords
SA1-68–SA1-71
10001XXXXX
128 (4x32) Kwords
SA2-19 - SA2-22
00011XXXXX
128 (4x32) Kwords
SA1-72–SA1-75
10010XXXXX
128 (4x32) Kwords
SA2-23 - SA2-26
00100XXXXX
128 (4x32) Kwords
SA1-76–SA1-79
10011XXXXX
128 (4x32) Kwords
SA2-27 - SA2-30
00101XXXXX
128 (4x32) Kwords
SA1-80–SA1-83
10100XXXXX
128 (4x32) Kwords
SA2-31 - SA2-34
00110XXXXX
128 (4x32) Kwords
SA1-84–SA1-87
10101XXXXX
128 (4x32) Kwords
SA2-35 - SA2-38
00111XXXXX
128 (4x32) Kwords
SA1-88–SA1-91
10110XXXXX
128 (4x32) Kwords
SA2-39 - SA2-42
01000XXXXX
128 (4x32) Kwords
SA1-92–SA1-95
10111XXXXX
128 (4x32) Kwords
SA2-43 - SA2-46
01001XXXXX
128 (4x32) Kwords
SA1-96–SA1-99
11000XXXXX
128 (4x32) Kwords
SA2-47 - SA2-50
01010XXXXX
128 (4x32) Kwords
SA1-100–SA1-103
11001XXXXX
128 (4x32) Kwords
SA2-51 - SA2-54
01011XXXXX
128 (4x32) Kwords
SA1-104–SA1-107
11010XXXXX
128 (4x32) Kwords
SA2-55 - SA2-58
01100XXXXX
128 (4x32) Kwords
SA1-108–SA1-111
11011XXXXX
128 (4x32) Kwords
SA2-59 - SA2-62
01101XXXXX
128 (4x32) Kwords
SA1-112–SA1-115
11100XXXXX
128 (4x32) Kwords
SA2-63 - SA2-66
01110XXXXX
128 (4x32) Kwords
SA1-116–SA1-119
11101XXXXX
128 (4x32) Kwords
SA2-67 - SA2-70
01111XXXXX
128 (4x32) Kwords
SA1-120–SA1-123
11110XXXXX
128 (4x32) Kwords
SA2-71 - SA2-74
10000XXXXX
128 (4x32) Kwords
SA1-124
1111100XXX
32 Kwords
SA2-75 - SA2-78
10001XXXXX
128 (4x32) Kwords
SA1-125
1111101XXX
32 Kwords
SA2-79 - SA2-82
10010XXXXX
128 (4x32) Kwords
SA1-126
1111110XXX
32 Kwords
SA2-83 - SA2-86
10011XXXXX
128 (4x32) Kwords
SA1-127
1111111000
4 Kwords
SA2-87 - SA2-90
10100XXXXX
128 (4x32) Kwords
SA1-128
1111111001
4 Kwords
SA2-91 - SA2-94
10101XXXXX
128 (4x32) Kwords
SA1-129
1111111010
4 Kwords
SA2-95 - SA2-98
10110XXXXX
128 (4x32) Kwords
SA1-130
1111111011
4 Kwords
SA2-99 - SA2-102
10111XXXXX
128 (4x32) Kwords
SA1-131
1111111100
4 Kwords
SA2-103 - SA2-106
11000XXXXX
128 (4x32) Kwords
SA1-132
1111111101
4 Kwords
SA2-107 - SA2-110
11001XXXXX
128 (4x32) Kwords
SA1-133
1111111110
4 Kwords
SA2-111 - SA2-114
11010XXXXX
128 (4x32) Kwords
SA1-134
1111111111
4 Kwords
SA2-115 - SA2-118
11011XXXXX
128 (4x32) Kwords
SA2-119 - SA2-122
11100XXXXX
128 (4x32) Kwords
SA2-123 - SA2-126
11101XXXXX
128 (4x32) Kwords
SA2-127 - SA2-130
11110XXXXX
128 (4x32) Kwords
SA2-131 - SA2-134
11111XXXXX
128 (4x32) Kwords
November 2, 2005
Am29PDL129H
19
Selecting a Sector Protection Mode
Persistent Protection Bit Lock
The device is shipped with all sectors unprotected.
AMD offers the option of programming and protecting
sectors at the factory prior to shipping the device
through AMD’s ExpressFlash™ Service. Contact an
AMD representative for details.
The Persistent Protection Bit (PPB) Lock is a volatile
bit that reflects the state of the Password Mode Locking Bit after power-up reset. If the Password Mode
Lock Bit is also set after a hardware reset (RESET#
asserted) or a power-up reset, the ONLY means for
clearing the PPB Lock Bit in Password Protection
Mode is to issue the Password Unlock command. Successful execution of the Password Unlock command
clears the PPB Lock Bit, allowing for sector PPBs
modifications. Asserting RESET#, taking the device
through a power-on reset, or issuing the PPB Lock Bit
Set command sets the PPB Lock Bit to a “1” when the
Password Mode Lock Bit is not set.
It is possible to determine whether a sector is protected or unprotected. See Autoselect Mode for details.
Table 9.
Sector Protection Schemes
Write Protect (WP#)
The Write Protect feature provides a hardware method
of protecting sectors without using VID. This function
is provided by the WP# pin and overrides the previously discussed High Voltage Sector Protection
method.
If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions in the two
outermost 4 Kword sectors on both ends of the flash
array independent of whether it was previously protected or unprotected.
If the system asserts VIH on the WP#/ACC pin, the device reverts to whether sectors were last set to be protected or unprotected. That is, sector protection or
unprotection for these sectors depends on whether
they were last protected or unprotected using the
method described in High Voltage Sector Protection.
Note that the WP#/ACC pin must not be left floating or
unconnected; inconsistent behavior of the device may
result.
If the Password Mode Locking Bit is not set, including
Persistent Protection Mode, the PPB Lock Bit is
cleared after power-up or hardware reset. The PPB
Lock Bit is set by issuing the PPB Lock Bit Set command. Once set the only means for clearing the PPB
Lock Bit is by issuing a hardware or power-up reset.
The Password Unlock command is ignored in Persistent Protection Mode.
High Voltage Sector Protection
Sector protection and unprotection may also be implemented using programming equipment. The procedure requires high voltage (VID) to be placed on the
RESET# pin. Refer to Figure 1 for details on this procedure. Note that for sector unprotect, all unprotected
sectors must first be protected prior to the first sector
write cycle.
Figure 1.
Temporary Sector Unprotect
indicator bits (DQ6, DQ7) to indicate the factorylocked and customer-locked status of the part.
Notes:
1. All protected sectors unprotected (If WP#/ACC = VIL,
sectors will remain protected).
The system accesses the through a command sequence (see “Enter /Exit Command Sequence”). After
the system has written the Enter command sequence,
it may read the by using the addresses normally occupied by the boot sectors. This mode of operation continues until the system issues the Exit command
sequence, or until power is removed from the device.
On power-up, or following a hardware reset, the device
reverts to sending commands to the normal address
space.
2. All previously protected sectors are protected once
again.
Figure 2.
Flash Memory Region
The SecSi (Secured Silicon) Sector feature provides a
Flash memory region that enables permanent part
identification through an Electronic Serial Number
(ESN) The 128-word SecSi sector is divided into 64
factory-lockable words that can be programmed and
locked by the customer. The SecSi sector is located at
addresses 000000h-00007Fh in both Persistent Protection mode and Password Protection mode. It uses
20
Factory-Locked Area (64 words)
The factory-locked area of the SecSi Sector (000000h00003Fh) is locked when the part is shipped, whether
or not the area was programmed at the factory. The
SecSi Sector Factory-locked Indicator Bit (DQ7) is permanently set to a “1”. AMD offers the ExpressFlash
service to program the factory-locked area with a random ESN, a customer-defined code, or any combina-
Am29PDL129H
November 2, 2005
tion of the two. Because only AMD can program and
protect the factory-locked area, this method ensures
the security of the ESN once the product is shipped to
the field. Contact an AMD representative for details on
using AMD’s ExpressFlash service. Note that the ACC
function and unlock bypass modes are not available
when the SecSi Sector is enabled.
Customer-Lockable Area (64 words)
The customer-lockable area of the SecSi Sector
(000040h-00007Fh) is shipped unprotected, which allows the customer to program and optionally lock the
area as appropriate for the application. The SecSi
Sector Customer-locked Indicator Bit (DQ6) is shipped
as “0” and can be permanently locked to “1” by issuing
November 2, 2005
the SecSi Protection Bit Program Command. The
SecSi Sector can be read any number of times, but
can be programmed and locked only once. Note that
the accelerated programming (ACC) and unlock bypass functions are not available when programming
the SecSi Sector.
The Customer-lockable area can be protected using
one of the following procedures:
Follow the SecSi Sector Protection Algorithm as
shown in . This allows in-system protection of the
SecSi Sector without raising any device pin to a high
voltage. Note that this method is only applicable to the
SecSi Sector.
Am29PDL129H
21
START
SecSiTM Sector Entry
Write AAh to address 555h
Write 55h to address 2AAh
Write 88h to address 555h
SecSi Sector
Protection Entry
Write AAh to address 555h
Write 55h to address 2AAh
Write 60h to address 555h
PLSCNT = 1
Protect SecSi Sector:
write 68h to sector address
with A7–A0 = 00011010
Time out 256 μs
Verify SecSi Sector:
write 48h to sector address
with A7–A0 = 00011010
Read from sector address
with A7–A0 = 00011010
No
Data = 01h?
Yes
SecSi Sector
Protection Completed
SecSi Sector Exit
Write 555h/AAh
Write 2AAh/55h
Write SA0+555h/90h
Write XXXh/00h
Figure 3. SecSi Sector Protection Algorithm
■ To verify the protect/unprotect status of the SecSi
Sector, follow the algorithm shown in Figure 4.
22
Am29PDL129H
November 2, 2005
Once the is locked and verified, the system must write the Exit Region command sequence to return to reading and
writing the remainder of the array.
The must be used with caution since, once locked, there is no procedure available for unlocking the area and none
of the bits in the memory space can be modified in any way.
SecSi Sector Protection Bits
The SecSi Sector Protection Bits prevent programming of the SecSi Sector memory area. Once set, the SecSi
Sector memory area contents are non-modifiable.
START
RESET# =
VIH or VID
Wait 1 μs
Write 60h to
any address
If data = 00h,
SecSi Sector is
unprotected.
If data = 01h,
SecSi Sector is
protected.
Remove VIH or VID
from RESET#
Write 40h to SecSi
Sector address
with A6 = 0,
A1 = 1, A0 = 0
Write reset
command
SecSi Sector
Protect Verify
complete
Read from SecSi
Sector address
with A6 = 0,
A1 = 1, A0 = 0
Figure 4.
SecSi Sector Protect Verify
COMMON FLASH MEMORY INTERFACE (CFI)
The Common Flash Interface (CFI) specification outlines device and host system software interrogation handshake, which allows specific vendor-specified software algorithms to be used for entire families of devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and backward-compatible for
the specified flash device families. Flash vendors can standardize their existing interfaces for long-term compatibility.
This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to address 55h, any
time the device is ready to read array data. The system can read CFI information at the addresses given in Tables
10–13. To terminate reading CFI data, the system must write the reset command. The CFI Query mode is not accessible when the device is executing an Embedded Program or embedded Erase algorithm.
The system can also write the CFI query command when the device is in the autoselect mode. The device enters
the CFI query mode, and the system can read CFI data at the addresses given in Tables 10–13. The system must
write the reset command to return the device to reading array data.
For further information, please refer to the CFI Specification and CFI Publication 100, available via the World Wide
Web at http://www.amd.com/flash/cfi. Alternatively, contact an AMD representative for copies of these documents.
Table 10.
Addresses
November 2, 2005
CFI Query Identification String
Data
Description
Am29PDL129H
23
10h
11h
12h
0051h
0052h
0059h
Query Unique ASCII string “QRY”
13h
14h
0002h
0000h
Primary OEM Command Set
15h
16h
0040h
0000h
Address for Primary Extended Table
17h
18h
0000h
0000h
Alternate OEM Command Set (00h = none exists)
19h
1Ah
0000h
0000h
Address for Alternate OEM Extended Table (00h = none exists)
Table 11.
Addresses
Data
Description
1Bh
0027h
VCC Min. (write/erase)
D7–D4: volt, D3–D0: 100 millivolt
1Ch
0036h
VCC Max. (write/erase)
D7–D4: volt, D3–D0: 100 millivolt
1Dh
0000h
VPP Min. voltage (00h = no VPP pin present)
1Eh
0000h
VPP Max. voltage (00h = no VPP pin present)
1Fh
0004h
Typical timeout per single byte/word write 2N µs
20h
0000h
Typical timeout for Min. size buffer write 2N µs (00h = not supported)
21h
0009h
Typical timeout per individual block erase 2N ms
22h
0000h
Typical timeout for full chip erase 2N ms (00h = not supported)
23h
0005h
Max. timeout for byte/word write 2N times typical
24h
0000h
Max. timeout for buffer write 2N times typical
25h
0004h
Max. timeout per individual block erase 2N times typical
26h
0000h
Max. timeout for full chip erase 2N times typical (00h = not supported)
Table 12.
24
System Interface String
Device Geometry Definition
Addresses
Data
Description
27h
0018h
Device Size = 2N byte
28h
29h
0001h
0000h
Flash Device Interface description (refer to CFI publication 100)
2Ah
2Bh
0000h
0000h
Max. number of byte in multi-byte write = 2N
(00h = not supported)
2Ch
0003h
Number of Erase Block Regions within device
2Dh
2Eh
2Fh
30h
0007h
0000h
0020h
0000h
Erase Block Region 1 Information
(refer to the CFI specification or CFI publication 100)
31h
32h
33h
34h
00FDh
0000h
0000h
0001h
Erase Block Region 2 Information
(refer to the CFI specification or CFI publication 100)
Am29PDL129H
November 2, 2005
35h
36h
37h
38h
0007h
0000h
0020h
0000h
Erase Block Region 3 Information
(refer to the CFI specification or CFI publication 100)
39h
3Ah
3Bh
3Ch
0000h
0000h
0000h
0000h
Erase Block Region 4 Information
(refer to the CFI specification or CFI publication 100)
November 2, 2005
Am29PDL129H
25
Table 13.
Primary Vendor-Specific Extended Query
Addresses
Data
Description
40h
41h
42h
0050h
0052h
0049h
Query-unique ASCII string “PRI”
43h
0031h
Major version number, ASCII (reflects modifications to the silicon)
44h
0033h
Minor version number, ASCII (reflects modifications to the CFI table)
45h
000Ch
Address Sensitive Unlock (Bits 1-0)
0 = Required, 1 = Not Required
Silicon Revision Number (Bits 7-2)
46h
0002h
Erase Suspend
0 = Not Supported, 1 = To Read Only, 2 = To Read & Write
47h
0001h
Sector Protect
0 = Not Supported, X = Number of sectors in per group
48h
0001h
Sector Temporary Unprotect
00 = Not Supported, 01 = Supported
49h
0007h
Sector Protect/Unprotect scheme
01 =29F040 mode, 02 = 29F016 mode, 03 = 29F400, 04 = 29LV800 mode
4Ah
00E7h
Simultaneous Operation
00 = Not Supported, X = Number of Sectors excluding Bank 1
4Bh
0000h
Burst Mode Type
00 = Not Supported, 01 = Supported
4Ch
0002h
Page Mode Type
00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page
4Dh
0085h
4Eh
0095h
4Fh
0001h
50h
0001h
57h
0004h
58h
0027h
59h
0060h
5Ah
0060h
5Bh
0027h
ACC (Acceleration) Supply Minimum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
ACC (Acceleration) Supply Maximum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
Top/Bottom Boot Sector Flag
26
00h = Uniform device, 02h = Bottom Boot Device, 03h = Top Boot Device, 04h = Both
Top and Bottom
Program Suspend
0 = Not supported, 1 = Supported
Bank Organization
00 = Data at 4Ah is zero, X = Number of Banks
Bank 1 Region Information
X = Number of Sectors in Bank 1
Bank 2 Region Information
X = Number of Sectors in Bank 2
Bank 3 Region Information
X = Number of Sectors in Bank 3
Bank 4 Region Information
X = Number of Sectors in Bank 4
Am29PDL129H
November 2, 2005
COMMAND DEFINITIONS
Enter /Exit Command Sequence
The region provides a secured data area containing a
random, eight word electronic serial number (ESN).
The system can access the region by issuing the
three-cycle Enter command sequence. The device
continues to access the region until the system issues
the four-cycle Exit command sequence. The Exit ommand sequence returns the device to normal operation. The SecSi Sector is not accessible when the
device is executing an Embedded Program or embedded Erase algorithm. shows the address and data requirements for both command sequences. See also
“SecSi Sector Flash Memory Region and Enter SecSi
Sector/Exit SecSi Sector Command Sequence” for further information. Note that the ACC function and unlock bypass modes are not available when the SecSi
Sector is enabled.
Figure 5.
If the Persistent Sector Protection Mode Locking Bit is
verified as programmed without margin, the Persistent
Sector Protection Mode Locking Bit Program Command should be reissued to improve program margin.
If the SecSi Sector Protection Bit is verified as programmed without margin, the SecSi Sector Protection
November 2, 2005
Bit Program Command should be reissued to improve
program margin. µµAfter programming a PPB, two additional cycles are needed to determine whether the
PPB has been programmed with margin. If the PPB
has been programmed without margin, the program
command should be reissued to improve the program
margin. Also note that the total number of PPB program/erase cycles is limited to 100 cycles. Cycling the
PPBs beyond 100 cycles is not guaranteed.
After erasing the PPBs, two additional cycles are
needed to determine whether the PPB has been
erased with margin. If the PPBs has been erased without margin, the erase command should be reissued to
improve the program margin.
PPB Lock Bit Status
Sector Protection Status The programming of
either the PPB or DYB for a given sector or sector
group can be verified by writing a Sector Protection
Status command to the device.
Note that there is no single command to independently
verify the programming of a DYB for a given sector
group.
Am29PDL129H
27
Command Definitions Tables
Table 14.
Memory Array Command Definitions
Cycles
Bus Cycles (Notes 1–4)
Command (Notes)
Read (5)
1
RA
Reset (6)
1
XXX
F0
Manufacturer ID
4
555
AA
2AA
55
555
90
(BA)X00
01
Device ID (10)
6
555
AA
2AA
55
555
90
(BA)X01
7E
Autoselect
(Note 7)
Addr Data Addr Data Addr Data
Addr
Data
Addr
Data
Addr
Data
(BA)X0E
21
(BA)X0F
00
RD
SecSi Sector Factory
Protect (8)
4
555
AA
2AA
55
555
90
X03
(see
note 8)
Sector Group Protect Verify
(9)
4
555
AAA
2AA
55
555
90
(SA)X02
XX00/
XX01
Program
4
555
AA
2AA
55
555
A0
PA
PD
Chip Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
555
10
Sector Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
SA
30
Program/Erase Suspend (11)
1
BA
B0
Program/Erase Resume (12)
1
BA
30
CFI Query (13)
1
55
98
Accelerated Program (15)
2
XX
A0
PA
PD
Unlock Bypass Entry (15)
3
555
AA
2AA
55
555
20
Unlock Bypass Program (15)
2
XX
A0
PA
PD
XX
10
XXX
00
Unlock Bypass Erase (15)
2
XX
80
Unlock Bypass CFI (13, 15)
1
XX
98
Unlock Bypass Reset (15)
2
XXX
90
Legend:
BA = Address of bank switching to autoselect mode, bypass mode, or
erase operation. Determined by A21:A20, see Tables 4 and for more
detail.
PA = Program Address (A21:A0). Addresses latch on falling edge of
WE# or CE1#/CE2# pulse, whichever happens later.
PD = Program Data (DQ15:DQ0) written to location PA. Data latches
on rising edge of WE# or CE1#/CE2# pulse, whichever happens first.
RA = Read Address (A21:A0).
RD = Read Data (DQ15:DQ0) from location RA.
SA = Sector Address (A21:A12) for verifying (in autoselect mode) or
erasing.
WD = Write Data. See “Configuration Register” definition for specific
write data. Data latched on rising edge of WE#.
X = Don’t care
Notes:
1. See Table 1 for description of bus operations.
8.
The data is C0h for factory or customer locked and 80h for factory
locked.
The data is 00h for an unprotected sector group and 01h for a
protected sector group.
2.
All values are in hexadecimal.
3.
Shaded cells in table denote read cycles. All other cycles are
write operations.
9.
4.
During unlock and command cycles, when lower address bits are
555 or 2AAh as shown in table, address bits higher than A11
(except where BA is required) and data bits higher than DQ7 are
don’t cares.
10. Device ID must be read across cycles 4, 5, and 6.
5.
No unlock or command cycles required when bank is reading
array data.
6.
The Reset command is required to return to reading array (or to
erase-suspend-read mode if previously in Erase Suspend) when
bank is in autoselect mode, or if DQ5 goes high (while bank is
providing status information).
7.
28
Fourth cycle of autoselect command sequence is a read cycle.
System must provide bank address to obtain manufacturer ID or
device ID information. See Autoselect Command Sequence for
more information.
11. System may read and program in non-erasing sectors, or enter
autoselect mode, when in Program/Erase Suspend mode.
Program/Erase Suspend command is valid only during a sector
erase operation, and requires bank address.
12. Program/Erase Resume command is valid only during Erase
Suspend mode, and requires bank address.
13. Command is valid when device is ready to read array data or
when device is in autoselect mode.
14. must be at VID during the entire operation of command.
15. Unlock Bypass Entry command is required prior to any Unlock
Bypass operation. Unlock Bypass Reset command is required to
return to the reading array.
Am29PDL129H
November 2, 2005
Table 15.
Sector Protection Command Definitions
Cycles
Bus Cycles (Notes 1-4)
Command
(Notes)
Reset
1 XXX
Addr Data Addr Data
Addr
Data
Addr
Data
Addr
Data
Addr
Data
OW
RD(0)
Addr
Data
PWA[3]
PWD[3]
F0
SecSi Sector Entry 3
555
AA
2AA
55
555
88
SecSi Sector Exit
4
555
AA
2AA
55
555
90
XX
00
SecSi Protection
Bit Program (5, 6)
6
555
AA
2AA
55
555
60
OW
68
OW
48
SecSi Protection
Bit Status
5
555
AA
2AA
55
555
60
OW
48
OW
RD(0)
Password Program
4
(5, 7, 8)
555
AA
2AA
55
555
38
XX[0-3]
PD[0-3]
Password Verify (6,
4
8, 9)
555
AA
2AA
55
555
C8
PWA[0-3]
PWD[0-3]
Password Unlock
(7, 10, 11)
7
555
AA
2AA
55
555
28
PWA[0]
PWD[0]
PWA[1]
PWD[1]
PWA[2]
PWD[2]
PPB Program (5, 6,
6
12, 17)
555
AA
2AA
55
555
60
(SA)WP
68
(SA)WP
48
(SA)WP
RD(0)
PPB Status
5
555
AA
2AA
55
555
60
(SA)WP
48
(SA)WP
RD (0)
All PPB Erase (5,
6, 13, 14)
6
555
AA
2AA
55
555
60
WP
60
(SA)
40
(SA)WP
RD(0)
PPB Lock Bit Set
(17)
3
555
AA
2AA
55
555
78
PPB Lock Bit
Status (15)
4
555
AA
2AA
55
555
58
SA
RD(1)
PL
RD(0)
SL
RD(0)
DYB Write (7)
4
555
AA
2AA
55
555
48
SA
X1
DYB Erase (7)
4
555
AA
2AA
55
555
48
SA
X0
DYB Status (6, 18) 4
555
AA
2AA
55
555
58
SA
RD(0)
PPMLB Program
(5, 6, 12)
6
555
AA
2AA
55
555
60
PL
68
PL
48
PPMLB Status (5)
5
555
AA
2AA
55
555
60
PL
48
PL
RD(0)
SPMLB Program
(5, 6, 12)
6
555
AA
2AA
55
555
60
SL
68
SL
48
SPMLB Status (5)
5
555
AA
2AA
55
555
60
SL
48
SL
RD(0)
Legend:
DYB = Dynamic Protection Bit
OW = Address (A7:A0) is (00011010)
PD[3:0] = Password Data (1 of 4 portions)
PPB = Persistent Protection Bit
PWA = Password Address. A1:A0 selects portion of password.
PWD = Password Data being verified.
PL = Password Protection Mode Lock Address (A7:A0) is (00001010)
RD(0) = Read Data DQ0 for protection indicator bit.
RD(1) = Read Data DQ1 for PPB Lock status.
SA = Sector Address where security command applies. Address bits
A21:A12 uniquely select any sector.
SL = Persistent Protection Mode Lock Address (A7:A0) is (00010010)
WP = PPB Address (A7:A0) is (00000010) (Note16)
X = Don’t care
PPMLB = Password Protection Mode Locking Bit
SPMLB = Persistent Protection Mode Locking Bit
1.
See Table 1 for description of bus operations.
11. A 2 µs timeout is required between any two portions of password.
2.
All values are in hexadecimal.
12. A 100 µs timeout is required between cycles 4 and 5.
3.
Shaded cells in table denote read cycles. All other cycles are
write operations.
13. A 1.2 ms timeout is required between cycles 4 and 5.
4.
During unlock and command cycles, when lower address bits are
555 or 2AAh as shown in table, address bits higher than A11
(except where BA is required) and data bits higher than DQ7 are
don’t cares.
14. Cycle 4 erases all PPBs. Cycles 5 and 6 validate bits have been
fully erased when DQ0 = 0. If DQ0 = 1 in cycle 6, erase command
must be issued and verified again. Before issuing erase
command, all PPBs should be programmed to prevent PPB
overerasure.
5.
The reset command returns device to reading array.
15. DQ1 = 1 if PPB locked, 0 if unlocked.
6.
Cycle 4 programs the addressed locking bit. Cycles 5 and 6
validate bit has been fully programmed when DQ0 = 1. If DQ0 = 0
in cycle 6, program command must be issued and verified again.
16. For PDL128G and PDL640G, the WP address is 0111010. The
EP address (PPB Erase Address) is 1111010.
7.
Data is latched on the rising edge of WE#.
8.
Entire command sequence must be entered for each portion of
password.
9.
Command sequence returns FFh if PPMLB is set.
17. Following the final cycle of the command sequence, the user must
write the first three cycles of the Autoselect command and then
write a Reset command.
18. If checking the DYB status of sectors in multiple banks, the user
must follow Note 17 before crossing a bank boundary.
10. The password is written over four consecutive cycles, at
addresses 0-3.
November 2, 2005
Am29PDL129H
29
ABSOLUTE MAXIMUM RATINGS
Storage Temperature
Plastic Packages . . . . . . . . . . . . . . . –65°C to +150°C
20 ns
Ambient Temperature
with Power Applied. . . . . . . . . . . . . . –65°C to +125°C
+0.8 V
Voltage with Respect to Ground
–0.5 V
VCC (Note 1) . . . . . . . . . . . . . . . . . –0.5 V to +4.0 V
A9, OE#, and RESET#
(Note 2) . . . . . . . . . . . . . . . . . . . . –0.5 V to +13.0 V
20 ns
–2.0 V
20 ns
(Note 2) . . . . . . . . . . . . . . . . . . . –0.5 V to +10.5 V
All other pins (Note 1) . . . . . . –0.5 V to VCC +0.5 V
Figure 6. Maximum Negative
Overshoot Waveform
Output Short Circuit Current (Note 3) . . . . . . 200 mA
Notes:
1. Minimum DC voltage on input or I/O pins is –0.5 V.
During voltage transitions, input or I/O pins may
overshoot V SS to –2.0 V for periods of up to 20 ns.
Maximum DC voltage on input or I/O pins is VCC +0.5 V.
See . During voltage transitions, input or I/O pins may
overshoot to VCC +2.0 V for periods up to 20 ns. See
Figure 7.
2. Minimum DC input voltage on pins A9, OE#, RESET#,
and WP#/ACC is –0.5 V. During voltage transitions, A9,
OE#, WP#/ACC, and RESET# may overshoot VSS to –
2.0 V for periods of up to 20 ns. See . Maximum DC input
voltage on pin A9, OE#, and RESET# is +12.5 V which
may overshoot to +14.0 V for periods up to 20 ns.
Maximum DC input voltage on WP#/ACC is +9.5 V which
may overshoot to +12.0 V for periods up to 20 ns.
20 ns
VCC
+2.0 V
VCC
+0.5 V
2.0 V
3. No more than one output may be shorted to ground at a
time. Duration of the short circuit should not be greater
than one second.
20 ns
20 ns
Figure 7. Maximum Positive
Overshoot Waveform
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device. This
is a stress rating only; functional operation of the device at
these or any other conditions above those indicated in the
operational sections of this data sheet is not implied.
Exposure of the device to absolute maximum rating
conditions for extended periods may affect device reliability.
OPERATING RANGES
Industrial (I) Devices
Ambient Temperature (TA) . . . . . . . . . –40°C to +85°C
Supply Voltages
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7–3.6 V
VIO (see Note) . . . . . . . . . . .1.65–1.95 V or 2.7–3.6 V
For all AC and DC specifications, VIO = VCC; contact
AMD for other VIO options.
Operating ranges define those limits between which the
functionality of the device is guaranteed.
30
Am29PDL129H
November 2, 2005
DC CHARACTERISTICS
CMOS Compatible
Parameter
Symbol
Parameter Description
Test Conditions
Min
Typ
Max
Unit
±1.0
µA
ILI
Input Load Current
VIN = VSS to VCC,
VCC = VCC max
ILIT
A9, OE#, RESET# Input Load Current
VCC = VCC max; VID= 12.5 V
35
µA
ILR
Reset Leakage Current
VCC = VCC max; VID= 12.5 V
35
µA
ILO
Output Leakage Current
VOUT = VSS to VCC, OE# = VIH
VCC = VCC max
±1.0
µA
ICC1
VCC Active Read Current (Notes 1, 2, 3)
OE# = VIH, VCC = VCC max
(Note 1)
ICC2
VCC Active Write Current (Notes 1, 3, 4)
ICC3
ICC4
5 MHz
20
30
10 MHz
45
55
OE# = VIH, WE# = VIL
15
25
mA
VCC Standby Current (Note 3)
CE1#, CE2#, RESET#, WP/ACC#
= VIO ± 0.3 V
1
5
µA
VCC Reset Current (Note 3)
RESET# = VSS ± 0.3 V, CE# = VSS
1
5
µA
ICC5
Automatic Sleep Mode (Notes 3, 5)
VIH = VIO ± 0.3 V;
VIL = VSS ± 0.3 V, CE# = VSS
1
5
µA
ICC6
VCC Active Read-While-Program Current
(Notes 1, 2, 3)
OE# = VIH
Word
21
45
mA
ICC7
VCC Active Read-While-Erase Current
(Notes 1, 2, 3)
OE# = VIH
Word
21
45
mA
ICC8
VCC Active Program-While-EraseSuspended Current (Notes 1, 3, 6)
OE# = VIH
17
25
mA
VIL
Input Low Voltage
VIH
Input High Voltage
VHH
Voltage for ACC Program Acceleration
VID
VOL
mA
VIO = 1.65–1.95 V
–0.4
0.4
V
VIO = 2.7–3.6 V
–0.5
0.8
V
VIO–0.4
VIO+0.4
V
VIO = 2.7–3.6 V
2.0
VCC+0.3
V
VCC = 3.0 V ± 10%
8.5
9.5
V
Voltage for Autoselect and Temporary
Sector Unprotect
VCC = 3.0 V ± 10%
11.5
12.5
V
Output Low Voltage
IOL = 100 µA, VCC = VCC min, VIO = 1.65–1.95
V
0.1
V
IOL = 2.0 mA, VCC = VCC min, VIO = 2.7–3.6 V
0.4
V
VOH
Output High Voltage
VLKO
Low VCC Lock-Out Voltage (Note 6)
VIO = 1.65–1.95 V
IOH = –100 µA, VCC = VCC min, VIO = 1.65–1.95 V
VIO–0.1
V
IOH = –2.0 mA, VCC = VCC min, VIO = 2.7–3.6 V
2.4
V
2.3
2.5
V
Notes:
1. Valid CE1#/CE2# conditions: (CE1#= VIL, CE2#= VIH) or (CE1#=
VIH, CE2#= VIL)
4.
ICC active while Embedded Erase or Embedded Program is in
progress.
2.
The ICC current listed is typically less than 5 mA/MHz, with OE# at
VIH.
5.
3.
Maximum ICC specifications are tested with VCC = VCCmax.
Automatic sleep mode enables the low power mode when
addresses remain stable for tACC + 150 ns. Typical sleep mode
current is 1 μA.
6.
Not 100% tested.
November 2, 2005
Am29PDL129H
31
TEST CONDITIONS
Table 16.
3.6 V
Test Condition
2.7 kΩ
Device
Under
Test
CL
Test Specifications
6.2 kΩ
All Speeds
Output Load
1 TTL gate
Output Load Capacitance, CL
(including jig capacitance)
30
pF
Input Rise and Fall Times
5
ns
0.0–3.0
V
Input timing measurement
reference levels
1.5
V
Output timing measurement
reference levels
1.5
V
Input Pulse Levels
Note: Diodes are IN3064 or equivalent
Figure 8.
Test Setup, VIO = 2.7 – 3.6 V
Unit
Note: For 70 pF output load capacitance, 2 ns will be added
to certain read-only operation parameters.
* For VIO = 1.65 – 1.95 Test Setup, the device is tested
using CL only
KEY TO SWITCHING WAVEFORMS
WAVEFORM
INPUTS
OUTPUTS
Steady
Changing from H to L
Changing from L to H
VIO
Input
Don’t Care, Any Change Permitted
Changing, State Unknown
Does Not Apply
Center Line is High Impedance State (High Z)
VIO/2
Measurement Level
VIO/2
Output
0.0 V
Figure 9.
32
Input Waveforms and Measurement Levels
Am29PDL129H
November 2, 2005
AC CHARACTERISTICS
CE1#/CE2# Timing
Parameter
JEDEC
Std
Description
CE1#/CE2# Recover Time
tCCR
All Speed Options
Unit
30
ns
Min
CE1#
tCCR
tCCR
CE2#
Figure 10.
Timing Diagram for Alternating Between CE1# and CE2# Control
Read-Only Operations
Parameter
Speed Options
JEDEC
Std.
Description
Test Setup
tAVAV
tRC
Read Cycle Time (Note 1)
tAVQV
tACC
Address to Output Delay (Note 3)
tELQV
tCE
Chip Enable to Output Delay (Note 4)
53
63
68
88
Unit
Min
55
65
65
85
ns
CE#, OE# = VIL
Max
55
65
65
85
ns
OE# = VIL
Max
60
65
70
85
ns
Max
20
25
30
ns
20
25
30
ns
tPACC Page Access Time
tGLQV
tOE
Output Enable to Output Delay
Max
tEHQZ
tDF
Chip Enable to Output High Z (Notes 1, 5, 6)
Max
16
ns
tGHQZ
tDF
Output Enable to Output High Z (Notes 1, 5)
Max
16
ns
tAXQX
tOH
Output Hold Time From Addresses, CE#/CE2#
or OE#, Whichever Occurs First (Notes 5, 6)
Min
5
ns
Read
Min
0
ns
tOEH
Output Enable Hold Time
(Note 1)
Toggle and
Data# Polling
Min
10
ns
Notes:
1.
Not 100% tested.
2.
See Figure 8 and Table 16 for test specifications
3.
4.
5.
Valid CE1#/CE2# conditions: (CE1#= VIL, CE2#= VIH) or (CE1#=
VIH, CE2#=VIL).
Measurements performed by placing a 50 ohm termination on the
data pin with a bias of VCC/2. The time from OE# high to the data
bus driven to VCC/2 is taken as tDF.
6.
Valid CE1#/CE2# transitions: (CE1#= CE2#= VIH) to (CE1#= VIL,
CE2#=VIH) or (CE1#= VIH, CE2#=VIL).
Valid CE1#/CE2# transitions: (CE1#= VIL, CE2#= VIH) or (CE1#=
VIH, CE2#=VIL) to (CE1#= CE2#= VIH).
7.
For 70 pF output load capacitance, 2 ns will be added to tACC, tCE,
tPACC, tOE values for all speed options.
November 2, 2005
Am29PDL129H
33
AC CHARACTERISTICS
tRC
Addresses Stable
Addresses
tACC
CE1# or CE2#
tRH
tRH
tDF
tOE
OE#
tOEH
WE#
tCE
tOH
HIGH Z
HIGH Z
Valid Data
Data
RESET#
RY/BY#
0V
Figure 11.
Read Operation Timings
Note:
1. During CE1# transitions, CE2#= VIH; During CE2# transitions, CE1#= VIH
Same Page
Addresses
A2-A0
Aa
tACC
Data
Ab
tPACC
Qa
Ad
Ac
tPACC
Qb
tPACC
Qc
Qd
CE1# or CE2#
OE#
Figure 12.
Page Read Operation Timings
Note:
1. During CE1# transitions, CE2#= VIH; During CE2# transitions, CE1#= VIH
34
Am29PDL129H
November 2, 2005
AC CHARACTERISTICS
Hardware Reset (RESET#)
Parameter
JEDEC
Std
Description
All Speed Options
Unit
tReady
RESET# Pin Low (During Embedded Algorithms)
to Read Mode (See Note)
Max
20
µs
tReady
RESET# Pin Low (NOT During Embedded
Algorithms) to Read Mode (See Note)
Max
500
ns
tRP
RESET# Pulse Width
Min
500
ns
tRH
Reset High Time Before Read (See Note)
Min
50
ns
tRPD
RESET# Low to Standby Mode
Min
20
µs
tRB
RY/BY# Recovery Time
Min
0
ns
Note: Not 100% tested.
RY/BY#
CE1# or CE2#, OE#
tRH
RESET#
tRP
tReady
Reset Timings NOT during Embedded Algorithms
Reset Timings during Embedded Algorithms
tReady
RY/BY#
tRB
CE1# or CE2#, OE#
RESET#
tRP
Figure 13.
Reset Timings
Note:
1. During CE1# transitions, CE2#= VIH; During CE2# transitions, CE1#= VIH
November 2, 2005
Am29PDL129H
35
AC CHARACTERISTICS
Erase and Program Operations
Parameter
Speed Options
JEDEC
Std.
Description
tAVAV
tWC
Write Cycle Time (Note 1)
Min
tAVWL
tAS
Address Setup Time
Min
0
ns
tASO
Address Setup Time to OE# low
during toggle bit polling
Min
15
ns
tAH
Address Hold Time
Min
tAHT
Address Hold Time From CE1#, CE2#, or OE# high
during toggle bit polling
Min
tDVWH
tDS
Data Setup Time
Min
tWHDX
tDH
Data Hold Time
Min
0
ns
tOEPH
Output Enable High during toggle bit polling
Min
10
ns
tGHWL
tGHWL
Read Recovery Time Before Write
(OE# High to WE# Low)
Min
0
ns
tELWL
tCS
CE1# or CE2# Setup Time
Min
0
ns
tWHEH
tCH
CE1# or CE2# Hold Time
Min
0
ns
tWLWH
tWP
Write Pulse Width
Min
35
40
ns
tWHDL
tWPH
Write Pulse Width High
Min
20
25
ns
tSR/W
Latency Between Read and Write Operations
Min
0
ns
tWLAX
53
63
68
88
Unit
55
65
65
85
ns
30
35
0
25
ns
ns
30
ns
tWHWH1
tWHWH1 Programming Operation (Note 2)
Typ
6
µs
tWHWH1
tWHWH1 Accelerated Programming Operation (Note 2)
Typ
4
µs
tWHWH2
tWHWH2 Sector Erase Operation (Note 2)
Typ
0.5
sec
tVCS
VCC Setup Time (Note 1)
Min
50
µs
tRB
Write Recovery Time from RY/BY#
Min
0
ns
Program/Erase Valid to RY/BY# Delay
Max
90
ns
tBUSY
Notes:
1. Not 100% tested.
2. See the “Erase And Programming Performance” section for more information.
36
Am29PDL129H
November 2, 2005
AC CHARACTERISTICS
Program Command Sequence (last two cycles)
tAS
tWC
Addresses
Read Status Data (last two cycles)
555h
PA
PA
PA
tAH
CE1# or CE2#
tCH
OE#
tWHWH1
tWP
WE#
tWPH
tCS
tDS
tDH
PD
A0h
Data
Status
tBUSY
DOUT
tRB
RY/BY#
VCC
tVCS
Notes:
1. PA = program address, PD = program data, DOUT is the true data at the program address.
2. During CE1# transitions, CE2#= VIH; During CE2# transitions, CE1#= VIH
Figure 14.
Program Operation Timings
VHH
WP#/ACC
VIL or VIH
VIL or VIH
tVHH
Figure 15.
November 2, 2005
tVHH
Accelerated Program Timing Diagram
Am29PDL129H
37
AC CHARACTERISTICS
Erase Command Sequence (last two cycles)
tAS
tWC
2AAh
Addresses
Read Status Data
VA
SA
VA
555h for chip erase
tAH
CE1# or CE2#
tCH
OE#
tWP
WE#
tWPH
tCS
tWHWH2
tDS
tDH
Data
55h
30h
Status
DOUT
10 for Chip Erase
tBUSY
tRB
RY/BY#
tVCS
VCC
Notes:
1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (.)
2. During CE1# transitions, CE2#= VIH; During CE2# transitions, CE1#= VIH
Figure 16.
38
Chip/Sector Erase Operation Timings
Am29PDL129H
November 2, 2005
AC CHARACTERISTICS
Addresses
tWC
tWC
tRC
Valid PA
Valid RA
tWC
tAH
tAS
Valid PA
Valid PA
tAS
tCPH
tACC
tAH
tCE
CE1# or CE2#
tCP
tOE
OE#
tOEH
tGHWL
tWP
WE#
tDF
tWPH
tDS
tOH
tDH
Valid
Out
Valid
In
Data
Valid
In
Valid
In
tSR/W
WE# Controlled Write Cycle
Read Cycle
CE# Controlled Write Cycles
Note:
1. During CE1# transitions, CE2#= VIH; During CE2# transitions, CE1#= VIH
Figure 17.
Back-to-back Read/Write Cycle Timings
tRC
Addresses
VA
VA
VA
tACC
tCE
CE1# or CE2#
tCH
tOE
OE#
tOEH
tDF
WE#
tOH
High Z
DQ7
Complement
Complement
DQ6–DQ0
Status Data
Status Data
True
Valid Data
High Z
True
Valid Data
tBUSY
RY/BY#
Note:
1. VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array data read
cycle. During CE1# transitions, CE2#= VIH;
2. During CE2# transitions, CE1#= VIH
Figure 18.
November 2, 2005
Data# Polling Timings (During Embedded Algorithms)
Am29PDL129H
39
AC CHARACTERISTICS
tAHT
tAS
Addresses
tAHT
tASO
CE1# or CE2#
tCEPH
tOEH
WE#
tOEPH
OE#
tDH
DQ6/DQ2
tOE
Valid Data
Valid
Status
Valid
Status
Valid
Status
(first read)
(second read)
(stops toggling)
Valid Data
RY/BY#
Notes:
1. VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last status read
cycle, and array data read cycle.
2. During CE1# transitions, CE2#= VIH; During CE2# transitions, CE1#= VIH
Figure 19.
Enter
Embedded
Erasing
WE#
Erase
Suspend
Erase
Toggle Bit Timings (During Embedded Algorithms)
Enter Erase
Suspend Program
Erase Suspend
Read
Erase
Suspend
Program
Erase
Resume
Erase Suspend
Read
Erase
Erase
Complete
DQ6
DQ2
Note:
1. DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE# to toggle
DQ2 and DQ6.
Figure 20.
40
DQ2 vs. DQ6
Am29PDL129H
November 2, 2005
AC CHARACTERISTICS
Temporary Sector Unprotect
Parameter
JEDEC
Std
Description
All Speed Options
Unit
tVIDR
VID Rise and Fall Time (See Note)
Min
500
ns
tVHH
VHH Rise and Fall Time (See Note)
Min
250
ns
tRSP
RESET# Setup Time for Temporary Sector
Unprotect
Min
4
µs
tRRB
RESET# Hold Time from RY/BY# High for
Temporary Sector Unprotect
Min
4
µs
Note: Not 100% tested.
VID
VID
RESET#
VIL or VIH
VIL or VIH
tVIDR
tVIDR
Program or Erase Command Sequence
CE1# or CE2#
WE#
tRRB
tRSP
RY/BY#
Note: During CE1# transitions, CE2#= VIH; During CE2# transitions, CE1#= VIH
Figure 21.
November 2, 2005
Temporary Sector Unprotect Timing Diagram
Am29PDL129H
41
AC CHARACTERISTICS
VID
VIH
RESET#
SA, A6,
A1, A0
Valid*
Valid*
Sector Group Protect/Unprotect
Data
60h
60h
Valid*
Verify
40h
Status
1 µs
Sector Group Protect: 150 µs
Sector Group Unprotect: 15 ms
CE1# or CE2#
WE#
OE#
* For sector protect, A6 = 0, A1 = 1, A0 = 0. For sector unprotect, A6 = 1, A1 = 1, A0 = 0.
Notes:
1. During CE1# transitions, CE2#= VIH; During CE2# transitions, CE1#= VIH
Figure 22.
42
Sector/Sector Block Protect and Unprotect Timing Diagram
Am29PDL129H
November 2, 2005
AC CHARACTERISTICS
Alternate CE# Controlled Erase and Program Operations
Parameter
Speed Options
JEDEC
Std.
Description
53
63
68
88
Unit
tAVAV
tWC
Write Cycle Time (Note 1)
Min
55
65
65
85
ns
tAVWL
tAS
Address Setup Time
Min
tELAX
tAH
Address Hold Time
Min
30
35
ns
tDVEH
tDS
Data Setup Time
Min
25
30
ns
tEHDX
tDH
Data Hold Time
Min
0
ns
tGHEL
tGHEL
Read Recovery Time Before Write
(OE# High to WE# Low)
Min
0
ns
tWLEL
tWS
WE# Setup Time
Min
0
ns
tEHWH
tWH
WE# Hold Time
Min
0
ns
tELEH
tCP
CE1# or CE2# Pulse Width
Min
35
40
ns
tEHEL
tCPH
CE1# or CE2# Pulse Width High
Min
20
25
ns
tWHWH1
tWHWH1
Programming Operation
(Note 2)
Typ
6
µs
tWHWH1
tWHWH1
Accelerated Programming Operation (Note 2)
Typ
4
µs
tWHWH2
tWHWH2
Sector Erase Operation (Note 2)
Typ
0.5
sec
0
ns
Notes:
1. Not 100% tested.
2. See the “Erase And Programming Performance” section for more information.
November 2, 2005
Am29PDL129H
43
AC CHARACTERISTICS
555 for program
2AA for erase
PA for program
SA for sector erase
555 for chip erase
Data# Polling
Addresses
PA
tWC
tAS
tAH
tWH
WE#
tGHEL
OE#
tWHWH1 or 2
tCP
CE1# or CE2#
tWS
tCPH
tBUSY
tDS
tDH
DQ7#
Data
tRH
A0 for program
55 for erase
DOUT
PD for program
30 for sector erase
10 for chip erase
RESET#
RY/BY#
Notes:
1.
2.
Figure indicates last two bus cycles of a program or erase operation.
PA = program address, SA = sector address, PD = program data.
3.
DQ7# is the complement of the data written to the device. DOUT is the data written to the device.
4.
During CE1# transitions, CE2#= VIH; During CE2# transitions, CE1#= VIH
Figure 23.
44
Alternate CE# Controlled Write (Erase/Program) Operation Timings
Am29PDL129H
November 2, 2005
ERASE AND PROGRAMMING PERFORMANCE
Parameter
Typ (Note 1)
Max (Note 2)
Unit
Comments
Sector Erase Time
0.4
5
sec
Chip Erase Time
108
Excludes 00h programming
prior to erasure (Note 4)
sec
Word Program Time
6
210
µs
Accelerated Word Program Time
4
120
µs
Chip Program Time (Note 3)
50
200
sec
Excludes system level
overhead (Note 5)
Notes:
1. Typical program and erase times assume the following conditions: 25°C, 3.0 V VCC, 1,000,000 cycles. Additionally,
programming typicals assume checkerboard pattern. All values are subject to change.
2. Under worst case conditions of 90°C, VCC = 2.7 V, 1,000,000 cycles. All values are subject to change.
3. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes
program faster than the maximum program times listed.
4. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.
5. System-level overhead is the time required to execute the two- or four-bus-cycle sequence for the program command. See Tables
for further information on command definitions.
6. The device has a minimum erase and program cycle endurance of 1,000,000 cycles.
LATCHUP CHARACTERISTICS
Description
Min
Max
Input voltage with respect to VSS on all pins except I/O pins
(including A9, OE#, and RESET#)
–1.0 V
13 V
Input voltage with respect to VSS on all I/O pins
–1.0 V
VCC + 1.0 V
–100 mA
+100 mA
VCC Current
Note: Includes all pins except VCC. Test conditions: VCC = 3.0 V, one pin at a time, VIO = VCC
BGA BALL CAPACITANCE
Parameter
Symbol
Parameter Description
Test Setup
Typ
Max
Unit
CIN
Input Capacitance
VIN = 0
4.2
5.0
pF
COUT
Output Capacitance
VOUT = 0
5.4
6.5
pF
CIN2
Control Pin Capacitance
VIN = 0
3.9
4.7
pF
Notes:
1.
Sampled, not 100% tested.
2.
Test conditions TA = 25°C, f = 1.0 MHz.
DATA RETENTION
Parameter Description
Test Conditions
Min
Unit
150°C
10
Years
125°C
20
Years
Minimum Pattern Data Retention Time
November 2, 2005
Am29PDL129H
45
REVISION SUMMARY
Sector Erase Command Sequence and Chip Erase
Command Sequence
Revision A (September 30, 2002)
Added “”
Initial release.
Table 14. “Memory Array Command Definitions
Revision A+1 (October 30, 2002)
Changed the first address of the unlock bypass reset
command sequence from BA to XXX.
Product Selector Guide
CMOS Compatible
Modified format of product selector guide table.
Added ILR parameter to table.
Ordering Information
Changed TBD to VK under the package type classification.
Deleted IACC parameter from table.
Revision A+2 (January 24, 2003)
Added VK packages to Valid Combinations table.
Ordering Information
Global
Changed 55 speed option to 53, changed 65 speed
option to 63 and 68.
Table 1. Am29PDL127H Device Bus Operations
Corrected the ordering part number and package
markings for the 83 and 88 speed options.
Revision A+3 (February 26, 2003)
Table 16. Test Specifications
Added note #2.
Updated output load capacitance.
Requirements for Reading Array Data
Revision A + 4 (April 22, 2003)
Reworded Page Mode Read section
Inserted and revised cross references.
Common Flash Memory Interface (CFI)
Changed wording in last sentence of third paragraph
from, “...the autoselect mode.” to “...reading array
data.”
Revision A+5 (June 20, 2003)
Changed CFI website address.
Changed the active read current to 55 mA.
Command Definitions
Product Selector Guide
Changed wording in last sentence of first paragraph
from, “...resets the device to reading array data.” to
...”may place the device to an unknown state. A reset
command is then required to return the device to
reading array data.”
Distinctive Characteristics
Added row to table to expand speed options and allow
for another VCC range.
Physical Dimensions
Removed the LAA064 package.
Revision B (July 29, 2003)
Customer Lockable: SecSi Sector NOT
Programmed or Protected at the factory.
Global
Added second bullet, SecSi sector-protect verify text
and Figure 3.
SecSi Sector Flash Memory Region and Enter
SecSi Sector/Exit SecSi Sector Command
Sequence
Added notes, “Note that the ACC function and unlock
bypass modes are not available when the SecSi sector
is enabled.”
Changed most CE# references to CE1#.
Changed Bank C to Bank 1A, Bank D to Bank 1B,
Bank A to Bank 2A, and Bank B to Bank 2B.
Sector Configuration Table
Corrected CE1# and CE2# bank references.
Table 4. Am29PDL129H Sector Architecture
Changed the Bank order to 1A, 1B, 2A, and 2B.
46
Am29PDL129H
November 2, 2005
Table 7. Am29PDL129H Boot Sector/Sector Block
Addresses for Protection/Unprotection
mA; changed program/erase current from 25 to 15
mA.
Broke table up into CE1# and CE2# versions and made
modifications to table values to reflect change.
Connection Diagrams
WP# Hardware Protection
Corrected signal descriptions for balls G1 and J1 on
80-ball fine-pitch BGA package (VBB080).
Indicated that a write protect pin that can prevent program or erase operations in sectors SA1-133, SA1134, SA2-0 and SA2-1.
Changed IOL test conditions for VOL from 4.0 mA to 2.0
mA.
Table 15. Sector Protection Command Definitions
Table 16, Test Specifications
Corrected typos in the PPB status row.
Changed CL from 70 pF to 30 pF. Added note for 70
pF load capacitance.
Added Note 17 to PPB Program and PPB Lock Bit Set
commands.
Added Note 18 to DYB Status.
DC Characteristics
AC Characteristics
Read-only Operations table: Added note for 70 pF
load capacitance.
Test Conditions
SecSiTM (Secured Silicon) Sector Flash Memory
Region
Added note to Figure 10.
Table 16. Test Specifications
Customer-Lockable Area: Added sector protection figure and changed figure reference in this section from
Figure 1 to Figure 3.
Added specific speed options to table.
CMOS Compatible Table
Added CE# = VSS to ICC4 and ICC5.
Table 16. Sector Protection Command Definitions
Modified values to read VCC.
Corrected number of cycles for SecSi Protection Bit
Status, PPMLB Status, and SPMLB Status from 4 to 5
cycles. For these command sequences, inserted a
cycle before the final read cycle (RD0).
Revision B+1 (August 8, 2003)
Revision B+3 (November 2, 2005)
Ordering Information
Updated migration statement on cover page and first
page of data sheet.
Figure 11. Input Waveforms and Measurement
Levels
Corrected typo in package marking.
Revision B+2 (December 5, 2003)
Global
Deleted the 83 speed option (85 ns tACC, VIO = 2.7–
3.6V). Replaced the 88 speed option (85 ns tACC, VIO
= 1.65–1.95V) with 78 (70 ns tACC, VIO = 1.65–1.95V).
This product has been retired and is not available for
designs. For new and current designs, Am29PDL129J
supersedes Am29PDL129H and is the factory-recomm e n d e d m i g r a t i o n p a t h . P l e a s e r e fe r t o t h e
Am29PDL129J datasheet for specifications and ordering information. Availability of this document is
retained for reference and historical purposes only.
Updated trademarks.
Distinctive Characteristics
Performance Characteristics: Under Power Consumption bullet, changed active read current from 55 to 45
Trademarks
Copyright © 2000−2005 Advanced Micro Devices, Inc. All rights reserved.
AMD, the AMD logo, and combinations thereof are registered trademarks of Advanced Micro Devices, Inc.
ExpressFlash is a trademark of Advanced Micro Devices, Inc.
Product names used in this publication are for identification purposes only and may be trademarks of their respective companies.
November 2, 2005
Am29PDL129H
47