SY89200U Ultra-Precision 1:8 LVDS Fanout Buffer with Three ÷1/÷2/÷4 Clock Divider Output Banks General Description The SY89200U is a 2.5V precision, high-speed, integrated clock divider and LVDS fanout buffer capable of handling clocks up to 1.5GHz. Optimized for communications applications, the three independently controlled output banks are phase matched and can be configured for pass through (÷1), ÷2 or ÷4 divider ratios. The differential input includes Micrel’s unique, 3-pin input termination architecture that allows the user to interface to any differential signal path. The low-skew, low-jitter outputs are LVDS-compatible with extremely fast rise/fall times guaranteed to be less than 150ps. The EN (enable) input guarantees that the ÷1, ÷2 and ÷4 outputs will start from the same state without any runt pulse after an asynchronous master rest (MR) is asserted. This is accomplished by enabling the outputs after a fourclock delay to allow the counters to synchronize. The SY89200U is part of Micrel’s Precision Edge® product family. Datasheets and support documentation can be found on Micrel’s web site at: www.micrel.com. Functional Block Diagram Precision Edge® Features • Three low-skew LVDS output banks with programmable ÷1, ÷2 and ÷4 divider options • Three independently programmable output banks • Guaranteed AC performance over temperature and voltage: – Accepts a clock frequency up to 1.5GHz – <900ps IN-to-OUT propagation delay – <150ps rise/fall time – <50ps bank-to-bank phase offset • Ultra-low jitter design: – <1psRMS random jitter – <10psPP total jitter (clock) • Patent-pending input termination and VT pin accepts DC- and AC-coupled inputs (CML, PECL, LVDS) • LVDS-compatible outputs • CMOS/TTL-compatible output enable (EN) and divider select control • 2.5V ±5% power supply • –40°C to +85°C temperature range • Available in 32-pin (5mm x 5mm) MLF® package Applications • All SONET/SD applications • All Fibre Channel applications • All Gigabit Ethernet applications Precision Edge is a registered trademark of Micrel, Inc MLF and MicroLeadFrame are registered trademark of Amkor Technology. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com March 2007 M9999-030707-D [email protected] or (408) 955-1690 Micrel, Inc. SY89200U Ordering Information(1) Part Number SY89200UMI SY89200UMITR (2) Package Type Temperature Range Package Marking Lead Finish MLF-32 Industrial SY89200U Sn-Pb MLF-32 Industrial SY89200U Sn-Pb SY89200UMG MLF-32 Industrial SY89200U with Pb-Free bar-line indicator Pb-Free NiPdAu SY89200UMGTR(2) MLF-32 Industrial SY89200U with Pb-Free bar-line indicator Pb-Free NiPdAu Note: 1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals only. 2. Tape and Reel. Pin Configuration 32-Pin MLF® (MLF-32) March 2007 2 M9999-030707-D [email protected] or (408) 955-1690 Micrel, Inc. SY89200U Pin Description Pin Number Pin Name 3, 6 IN, /IN Pin Function 2 7 8 DIVSEL1 DIVSEL2 DIVSEL3 4 VT 5 VREF-AC 9 EN Single-Ended Input: This TTL/CMOS input disable and enable the Q0 – Q7 outputs. This input is internally connected to a 25kΩ pull-up resistor and will default to logic HIGH state if left open. The input-switching threshold is VCC/2. For the input enable and disable functional description, refer to Figures 2a through 2c. 30, 29, 28, 27, 26, 25, 24, 23 Q0, /Q0, /Q1, /Q1, Q2, /Q2 Q3, /Q3 Bank 1 LVDS differential output pairs controlled by DIVSEL1: LOW Q0 – Q3 = ÷1 HIGH, Q0 – Q3 = ÷2. Unused output pairs should be terminated with 100Ω across the differential pair. 16, 15, 14, 13, 12, 11 Q4, /Q4, Q5, /Q5, Q6, /Q6 Bank 2 LVDS differential output pairs controlled by DIVSEL2: LOW Q4 – Q6 = ÷2 HIGH, Q4 – Q6 = ÷2. Unused output pairs should be terminated with 100Ω across the differential pair. 18, 17 Q7, /Q7 32 /MR Single-Ended Input: This TTL/CMOS-compatible master reset function asynchronously sets Q0 – Q7 outputs LOW, /Q0 – /Q7 outputs HIGH, and holds them in that state as long as /MR remains LOW. This input is internally connected to a 25kΩ pull-up resistor and will default to a logic HIGH state if left open. The input-switching threshold is VCC/2. 10, 19, 22, 31 VCC Positive power supply. Bypass with 0.1µF||0.01µF low ESR capacitors. 1, 20, 21 GND Exposed Differential Input: This input pair is the differential signal input to the device. This input accepts AC- or DC-coupled signals as small as 100mV. The input pair internally terminates to a VT pin through 50Ω. Note that these inputs will default to an indeterminate state if left open. Please refer to the “Input Interface Applications” section for more details. Single-Ended Inputs: These TTL/CMOS inputs select the device ratio for each of the three banks of outputs. Note that each of these inputs is internally connected to a 25kΩ pull-up resistor and will default to logic HIGH state if left open. The input-switching threshold is VCC/2. Input Termination Center-Tap: Each side of the differential input pair terminates to the VT pin. The VT pin provides a center-tap to a termination network for maximum interface flexibility. See “Input Interface Applications” section for more details. Reference Voltage: This output biases to VCC-1.2V. It is used for AC-coupling inputs IN and /IN. For AC-coupled applications, connect VREF-AC directly to the VT pin. Bypass with 0.01µF low ESR capacitor to VCC. Maximum sink/source capability is 0.5mA. Bank 3 LVDS differential output pairs controlled by DIVSEL3: LOW Q7 = ÷2 HIGH. Q7 = ÷2. Unused output pairs should be terminated with 100Ω across the differential pair. Ground and exposed pad must be connected to the same GND plane on the board. Truth Table /MR(1) EN(2,3) DIVSEL1 DIVSEL2 DIVSEL3 Q0 – Q3 Q4 – Q6 Q7 0 X X X X 0 0 0 1 0 X X X 0 0 0 1 1 0 0 0 ÷1 ÷2 ÷2 1 1 1 1 1 ÷2 ÷4 ÷4 Notes: 1. /MR asynchronously forces Q0 – Q7 LOW (/Q0 – /Q7 HIGH). 2. EN forces Q0 – Q7 LOW between 2 and 6 input clock cycles after the falling edge of EN. Refer to “Timing Diagram” section. 3. EN synchronously enables the outputs between two and six input clock cycles after the rising edge of EN. Refer to “Timing Diagram” section. March 2007 3 M9999-030707-D [email protected] or (408) 955-1690 Micrel, Inc. SY89200U Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VCC).................................... –0.5V to +4.0V Input Voltage (VIN) ............................................ –0.5V to VCC Termination Current(3) Source or sink current on VT .............................±100mA Output Current(3) Source or sink current on IN, /IN ........................±50mA VREF-AC Current(3) Source or sink current on VREF-AC .........................±2mA Lead Temperature (soldering, 20 sec.).................... +260°C Storage Temperature (Ts) .........................–65°C to +150°C Supply Voltage (VCC)............................ +2.375V to +2.625V Ambient Temperature (TA) .......................... –40°C to +85°C Package Thermal Resistance(4) MLF® (θJA) Still-Air.........................................................35°C/W MLF® (ΨJB) Junction –to-Board ......................................20°C/W DC Electrical Characteristics TA = –40°C to +85°C, unless otherwise stated. Symbol Parameter Condition Min Typ Max Units 2.375 2.5 2.625 V 350 mA VCC Power Supply ICC Power Supply Current RDIFF_IN Differential Input Resistance (IN-to-/IN) 80 100 120 Ω RIN Input Resistance (IN-to-VT, /IN-to-VT) 40 50 60 Ω VIH Input High Voltage; (IN, /IN) 1.2 VCC V VIL Input Low Voltage; (IN, /IN) 0 VIH-0.1 V VIN Input Voltage Swing; (IN, /IN) See Figure 1a. 100 VCC mV VDIFF_IN Differential Input Voltage Swing |IN - /IN| See Figure 1b. 200 2xVCC mV VREF-AC Reference Voltage VCC–1.1 V IN-to-VT Voltage from Input to VT 1.8 V Max Units No load, max. VCC, Note 6 VCC–1.3 VCC–1.2 LVTTL/CMOS DC Electrical Characteristics(5) VCC = 2.5V ±5%; TA = –40°C to +85°C, unless otherwise stated. Symbol Parameter VIH Input HIGH Voltage VIL Input LOW Voltage IIH Input HIGH Current IIL Input Low Current Condition Min Typ 2.0 –125 V 0.8 V 30 µA –300 µA Notes: 1. Permanent device damage may occur if ratings in the “Absolute Maximum Ratings” section are exceeded. This is a stress rating only and functional operation is not implied for conditions other than those detailed in the operational sections of this datasheet. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability. 2. The datasheet limits are not guaranteed if the device is operated beyond the operating ratings. 3. Due to the limited drive capability use for input of the same package only. 4. Package thermal resistance assumes exposed pad is soldered (or equivalent) to the device’s most negative potential on the PCB. ΨJB uses 4-layer θJA in still-air, unless otherwise stated. 5. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. 6. Includes current through internal 50Ω pull-up. March 2007 4 M9999-030707-D [email protected] or (408) 955-1690 Micrel, Inc. SY89200U LVDS OUTPUT DC Electrical Characteristics(7) VCC = 2.5V ±5%; TA = –40°C to +85°C; RL = 100Ω across Q and /Q, unless otherwise stated. Symbol Parameter VOH Output HIGH Voltage; (Q, /Q) Condition Min Typ Max Units 1.475 V VOL Output LOW Voltage; (Q, /Q) 0.925 VOUT Output Voltage Swing; (Q, /Q) 250 350 mV V VDIFF_OUT Differential Output Voltage Swing |Q – /Q| 500 700 mV VOCM Output Common Mode Voltage (Q, /Q) ∆VOCM Change in Common Mode Voltage (Q, /Q) 1.125 1.275 V –50 +50 mV Max Units AC Electrical Characteristics(8) VCC = 2.5V ±5%; TA = –40°C to +85°C; RL = 100Ω across all outputs (Q and /Q), unless otherwise stated. Symbol Parameter Condition fMAX Maximum Operating Frequency VOUT >200mV tPD Differential Propagation Delay IN-to-Q Min Clock Typ 1.5 500 GHz 700 /MR-to-Q ps 900 ps tRR Reset Recovery Time tPD Tempco Differential Propagation Delay Temperature Coefficient tSKEW Within-Bank Skew Within same fanout bank, Note 9 10 25 ps Bank-to-Bank Skew Same divide setting, Note 10 15 35 ps Bank-to-Bank Skew Differential divide setting, Note 10 25 50 ps Part-to-Park Skew Note 11 200 ps Random Jitter (RJ) Note 12 1 psRMS Total Jitter (TJ) Note 13 10 psPP Cycle-to-Cycle Jitter Note 14 1 psRMS Rise/Fall Time 20% to 80% at full output swing 150 ps tJITTER tf, tf /MR(L-H)-to-(L-H) 900 900 115 40 80 ps fs/°C Notes: 7. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. 8. Measured with 100mV input swing. See “Timing Diagram” section for definition of parameters. High-frequency AC-parameters are guaranteed by design and characterization. 9. Within-bank is the difference in propagation delays among the outputs within the same bank. 10. Bank-to-bank skew is the difference in propagation delays between outputs from difference banks. Bank-to-bank skew is also the phase offset between each bank after MR is applied. 11. Part-to-part skew is defined for two parts with identical power supply voltages at the same temperature and with no skew of the edges at the respective inputs. 12. RJ is measured with a K28.7 comma detect character pattern. 12 13. Total jitter definition: with an ideal clock input of frequency ≤fMAX, no more than one output edge in 10 output edges will deviate by more than the specified peak-to-peak jitter value. 14. Cycle-to-cycle jitter definition: the variation of periods between adjacent cycles, Tn – Tn-1 where T is the time between rising edges of the output signal. March 2007 5 M9999-030707-D [email protected] or (408) 955-1690 Micrel, Inc. SY89200U Single-Ended Differential Swings Figure 1a. Single-Ended Voltage Swing Figure 1b. Differential Voltage Swing Timing Diagram Figure 2a. Reset with Output Enabled March 2007 6 M9999-030707-D [email protected] or (408) 955-1690 Micrel, Inc. SY89200U Figure 2b. Enable Timing Figure 2c. Disable Timing March 2007 7 M9999-030707-D [email protected] or (408) 955-1690 Micrel, Inc. SY89200U Typical Operating Characteristics March 2007 8 M9999-030707-D [email protected] or (408) 955-1690 Micrel, Inc. SY89200U Input Stage Internal Termination Figure 3. Simplified Differential Input Stage Input Interface Applications Figure 4a. CML Interface (DC-Coupled) Figure 4b. CML Interface (AC-Coupled) Figure 4d. LVPECL Interface (AC-Coupled) Figure 4e. LVDS Interface March 2007 9 Figure 4c. LVPECL Interface (DC-Coupled) M9999-030707-D [email protected] or (408) 955-1690 Micrel, Inc. SY89200U Output Interface Applications LVDS specifies a small swing of 350mV typical, on a nominal 1.25V common mode above ground. The common mode voltage has tight limits to permit large variations in ground between an LVDS driver and receiver. Also, change in common mode voltage, as a function of data input, is kept to a minimum to keep EMI low. Figure 5b. LVDS Common Mode Measurement Figure 5a. LVDS Differential Measurement Related Product and Support Documentation Part Number Function ® HBW Solutions March 2007 Datasheet Link MLF Application Note www.amkor.com/products/notes_papers/MLF_AppNote_0902.pdf New Products and Applications www.micrel.com/product-info/products/solutions.shtml 10 M9999-030707-D [email protected] or (408) 955-1690 Micrel, Inc. SY89200U Package Information 32-Pin MicroLeadFrame® (MLF-32) MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2006 Micrel, Incorporated. March 2007 11 M9999-030707-D [email protected] or (408) 955-1690