TI SN65LVDS32BDR

SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
D
D
D
D
D
D
D
D
D
D
D
D
Meets or Exceeds the Requirements of
ANSI EIA/TIA-644 Standard for Signaling
Rates† up to 400 Mbps
Operates With a Single 3.3-V Supply
–2-V to 4.4-V Common-Mode Input Voltage
Range
Differential Input Thresholds <50 mV With
50 mV of Hysteresis Over Entire
Common-Mode Input Voltage Range
Integrated 110-Ω Line Termination
Resistors Offered With the LVDT Series
Propagation Delay Times 4 ns (typ)
Active Fail Safe Assures a High-Level
Output With No Input
Bus-Pin ESD Protection Exceeds
15 kV HBM
Inputs Remain High-Impedance on Power
Down
Recommended Maximum Parallel Rate of
200 M-Transfers/s
Available in Small-Outline Package With
1,27 mm Terminal Pitch
Pin-Compatible With the AM26LS32,
MC3486, or µA9637
description
This family of differential line receivers offers
improved performance and features that implement the electrical characteristics of low-voltage
differential signaling (LVDS). LVDS is defined in
the TIA/EIA-644 standard. This improved performance represents the second generation of
receiver products for this standard, providing a
better overall solution for the cabled environment.
This generation of products is an extension to TI’s
overall product portfolio and is not necessarily a
replacement for older LVDS receivers.
Improved features include an input commonmode voltage range 2 V wider than the minimum
required by the standard. This will allow longer
cable lengths by tripling the allowable ground
noise tolerance to 3 V between a driver and
receiver. TI has additionally introduced an even
wider input common-mode voltage range of –4 to
5 V in their SN65LVDS/T33 and SN65LVDS/T34.
SN65LVDS32B
SN65LVDT32B
Logic Diagram
(positive logic)
D PACKAGE
(TOP VIEW)
1B
1A
1Y
G
2Y
2A
2B
GND
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC
4B
4A
4Y
G
3Y
3A
3B
G
G
SN65LVDT32B
ONLY (4 Places)
1A
1Y
1B
2A
2Y
2B
3A
3Y
3B
4A
4Y
4B
SN65LVDS3486B
SN65LVDT3486B
Logic Diagram
(positive logic)
D PACKAGE
(TOP VIEW)
1B
1A
1Y
1,2EN
2Y
2A
2B
GND
SN65LVDT3486B
1
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
VCC
ONLY (4 Places)
1A
4B
4A
1B
1,2EN
4Y
2A
3,4EN
3Y
2B
3A
3A
3B
3B
3,4EN
4A
1Y
2Y
3Y
4Y
4B
SN65LVDS9637B
SN65LVDT9637B
D PACKAGE
(TOP VIEW)
VCC
1Y
2Y
GND
1
8
2
7
3
6
4
5
Logic Diagram
(positive logic)
1A
1B
2A
2B
1A
1Y
1B
SN65LVDT9637B
ONLY
2A
2Y
2B
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
† Signaling rate, 1/t, where t is the minimum unit interval and is expressed in the units bits/s (bits per second)
Copyright  2001, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
description (continued)
Precise control of the differential input voltage thresholds now allows for inclusion of 50 mV of input voltage
hysteresis to improve noise rejection on slowly changing input signals. The input thresholds are still no more
than ±50 mV over the full input common-mode voltage range.
The high-speed switching of LVDS signals almost always necessitates the use of a line impedance matching
resistor at the receiving-end of the cable or transmission media. The SN65LVDT series of receivers eliminates
this external resistor by integrating it with the receiver. The nonterminated SN65LVDS series is also available
for multidrop or other termination circuits.
The receivers can withstand ±15-kV human-body model (HBM) and ±600 V-machine model (MM) electrostatic
discharges to the receiver input pins with respect to ground without damage. This provides reliability in cabled
and other connections where potentially damaging noise is always a threat.
The receivers also include a (patent pending) fail-safe circuit that will provide a high-level output within 600 ns
after loss of the input signal. The most common causes of signal loss are disconnected cables, shorted lines,
or powered-down transmitters. This prevents noise from being received as valid data under these fault
conditions. This feature may also be used for wired-OR bus signaling.
The intended application of these devices and signaling technique is for point-to-point baseband data
transmission over controlled impedance media of approximately 100 Ω. The transmission media may be
printed-circuit board traces, backplanes, or cables. The ultimate rate and distance of data transfer is dependent
upon the attenuation characteristics of the media and the noise coupling to the environment.
The SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B, SN65LVDT3486B, SN65LVDS9637B, and
SN65LVDT9637B are characterized for operation from -40°C to 85°C.
AVAILABLE OPTIONS
PART NUMBER†
NUMBER OF
RECEIVERS
SN65LVDS32BD
SN65LVDT32BD
SN65LVDS3486BD
SN65LVDT3486BD
SN65LVDS9637BD
TERMINATION
RESISTOR†
SYMBOLIZATION
4
No
LVDS32B
4
Yes
LVDT32B
4
No
LVDS3486
4
Yes
LVDT3486
2
No
DK637B
Yes
DR637B
SN65LVDT9637BD
2
† Add the suffix R for taped and reeled carrier.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
Function Tables
SN65LVDS32B and SN65LVDT32B
DIFFERENTIAL INPUT
ENABLES
OUTPUT
A-B
G
G
Y
VID ≥ -32 mV
H
X
X
L
H
H
-100 mV < VID ≤ -32 mV
H
X
X
L
?
?
VID ≤ -100 mV
H
X
X
L
L
L
X
L
H
Z
Open
H
X
X
L
H
H
H = high level, L = low level, X = irrelevant,
Z = high impedance (off), ? = indeterminate
SN65LVDS3486B and SN65LVDT3486B
DIFFERENTIAL INPUT
ENABLES
OUTPUT
A-B
EN
Y
VID ≥ -32 mV
-100 mV < VID ≤ -32 mV
H
H
H
?
VID ≤ -100 mV
X
H
L
L
Z
Open
H
H
H = high level, L = low level, X = irrelevant,
Z = high impedance (off), ? = indeterminate
SN65LVDS9637B and SN65LVDT9637B
DIFFERENTIAL INPUT
OUTPUT
A-B
Y
VID ≥ -32 mV
-100 mV < VID ≤ -32 mV
H
VID ≤ -100 mV
Open
H = high level,
L
H
L = low level,
POST OFFICE BOX 655303
?
? = indeterminate
• DALLAS, TEXAS 75265
3
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
equivalent input and output schematic diagrams
VCC
Attenuation
Network
Attenuation
Network
1 pF
60 kΩ
A Input
200 kΩ
3 pF
6.5 kΩ
250 kΩ
Attenuation
Network
6.5 kΩ
VCC
B Input
7V
7V
7V
7V
LVDT Only 110 Ω
VCC
VCC
300 kΩ
(G Only)
Enable
Inputs
50 Ω
37 Ω
Y Output
7V
7V
300 kΩ
(EN and G Only)
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
absolute maximum ratings over operating free-air temperature (unless otherwise noted)†
Supply voltage range, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4 V
Voltage range: Enables or Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 3 V
A or B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –4 V to 6 V
VA – VB (LVDT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 V
Electrostatic discharge: A, B, and GND (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . Class 3, A: 15 kV, B: 600 V
Continuous power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential I/O bus voltages, are with respect to network ground terminal.
2. Tested in accordance with MIL-STD-883C Method 3015.7.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
OPERATING FACTOR‡
ABOVE TA = 25°C
TA = 85°C
POWER RATING
D8
725 mW
5.8 mW/°C
377 mW
D16
950 mW
7.6 mW/°C
494 mW
‡ This is the inverse of the junction-to-ambient thermal resistance when board-mounted and with
no air flow.
recommended operating conditions
Supply voltage, VCC
High-level input voltage, VIH
Enables
Low-level input voltage, VIL
Enables
voltage  VID
Magnitude of differential input voltage,
MIN
NOM
MAX
3
3.3
3.6
2
LVDS
0.1
Operating free-air temperature, TA
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
V
V
0.8
V
3
V
0.8
V
–2
4.4
V
–40
85
°C
LVDT
Voltage at any bus terminal (separately or common-mode), VI or VIC
UNIT
5
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
electrical characteristics over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
VIT1
VIT2
Positive-going differential input voltage threshold
Negative-going differential input voltage threshold
VIB = –2 V or 4.4 V,,
See Figures 1 and 2
–50
VIT3
Differential input fail-safe voltage threshold
See Table 1 and Figure 5
–32
VID(HYS)
Differential input voltage hysteresis,
VIT1 - VIT2
VOH
VOL
ICC
High-level output voltage
S
Supply
l currentt
‘32B or ‘3486B
SN65LVDS
II
Input current (A or B inputs)
SN65LVDT
IID
Differential input current
(IIA - IIB)
SN65LVDS
SN65LVDT
SN65LVDS
II(OFF)
Power-off input current
(A or B inputs)
SN65LVDT
IIH
IIL
High-level input current (enables)
–100
G or EN at VCC,
Steady-state
16
23
1.1
5
No load,
Steady-state
VI = 0 V,
VI =2.4 V,
Other input open
±20
Other input open
±20
VI = –2 V,
VI = 4.4 V,
Other input open
±40
Other input open
±40
VI = 0 V,
VI =2.4 V,
Other input open
±40
Other input open
±40
VI =–2 V,
VI = 4.4 V,
Other input open
±80
Other input open
±80
VID= 100 mV,
See Figure 1
8
VIC= –2 V or 4.4 V,
VID= 0.2 V,
VIC= –2 V or 4.4 V
VA or VB= 0 V or 2.4 V,
VCC= 0 V
Low-level input current (enables)
1.55
mA
A
µA
µA
µA
2.22
mA
±20
VA or VB= 0 V or 2.4 V,
VCC= 0 V
±30
VA or VB= –2 V or 4.4 V,
VCC= 0 V
±50
• DALLAS, TEXAS 75265
V
±3
±35
POST OFFICE BOX 655303
mV
12
VA or VB= –2 V or 4.4 V,
VCC= 0 V
VI = 0.4 sin (4E6πt) + 0.5 V
mV
V
0.4
No load,
UNIT
mV
2.4
µA
VIH = 2 V
VIL = 0.8 V
IOZ
High-impedance output current
CI
Input capacitance, A or B input to GND
† All typical values are at 25°C and with a 3.3 V supply.
6
50
G or EN at GND
‘9637B
MAX
50
IOH = –4 mA
IOL = 4 mA
Low-level output voltage
TYP†
5
10
µA
10
µA
±10
µA
pF
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
switching characteristics over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP†
MAX
2.5
4
6
ns
2.5
4
6
ns
9
ns
1.5
µs
UNIT
tPLH
tPHL
Propagation delay time, low-to-high-level output
td1
td2
Delay time, fail-safe deactivate time
tsk(p)
tsk(o)
Pulse skew (|tPHL1 – tPLH1|)
Output skew§
tsk(pp)
tr
Part-to-part skew‡
Output signal rise time
0.8
ns
tf
tPHZ
Output signal fall time
0.8
ns
Propagation delay time, high-level-to-high-impedance output
5.5
9
ns
tPLZ
tPZH
Propagation delay time, low-level-to-high-impedance output
4.4
9
ns
3.8
9
ns
Propagation delay time, high-to-low-level output
See Figure 3
See Figures 3 and 6
Delay time, fail-safe activate time
0.3
200
ps
150
ps
F
CL = 10 pF,
See Figure 3
Propagation delay time, high-impedance -to-high-level output
See Figure 4
1
ns
tPZL
Propagation delay time, high-impedance-to-low-level output
7
9
ns
† All typical values are at 25°C and with a 3.3-V supply.
‡ tsk(pp) is the magnitude of the time difference in propagation delay times between any specified terminals of two devices when both devices
operate with the same supply voltages, at the same temperature, and have identical packages and test circuits.
§ tsk(o) is the magnitude of the time difference between the tPLH or tPHL of all receivers of a single device with all of their inputs driven together.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
PARAMETER MEASUREMENT INFORMATION
IIA
A
VO
Y
VID
B
(VIA + VIB)/2
VIA
VIC
IIB
VO
VIB
Figure 1. Voltage and Current Definitions
1000 Ω
100 Ω
100 Ω†
VID
1000 Ω
VIC
+
–
10 pF,
2 Places
VO
10 pF
† Removed for testing the LVDT device
VIT1
0V
VID
–100 mV
VO
100 mV
VID
0V
VIT2
VO
NOTE: Input signal of 3 Mpps, duration of 167 ns, and transition time of <1 ns.
Figure 2. VIT1 and VIT2 Input Voltage Threshold Test Circuit and Definitions
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
PARAMETER MEASUREMENT INFORMATION
VID
VIA
CL = 10 pF
VIB
VO
VIA
1.4 V
VIB
1V
0.4 V
VID
0V
–0.4 V
tPHL
tPLH
80%
VO
20%
VOH
1.4 V
VOL
80%
20%
tf
tr
NOTE: All input pulses are supplied by a generator having the following characteristics: tr or tf ≤ 1 ns, pulse repetition rate (PRR) = 50 Mpps,
Pulsewidth = 10 ±0.2 ns . CL includes instrumentation and fixture capacitance within 0,06 mm of the D.U.T.
Figure 3. Timing Test Circuit and Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
PARAMETER MEASUREMENT INFORMATION
1.2 V
B
500 Ω
A
10 pF
Inputs
±
VO
G
VTEST
G
1,2,EN, or 3,4, EN
NOTE: All input pulses are supplied by a generator having the following characteristics: tr or tf ≤ 1 ns, pulse
repetition rate (PRR) = 0.5 Mpps, Pulsewidth = 500 ±10 ns . CL includes instrumentation and fixture
capacitance within 0,06 mm of the D.U.T.
2.5 V
VTEST
A
1V
2V
1.4 V
0.8 V
G, 1,2EN,or 3,4EN
2V
1.4 V
0.8 V
tPLZ
G
tPLZ
tPZL
tPZL
Y
VTEST
2.5 V
1.4 V
VOL +0.5 V
VOL
0
1.4 V
A
G, 1,2EN,or 3,4EN
2V
1.4 V
0.8 V
G
2V
1.4 V
0.8 V
tPHZ
tPHZ
tPZH
tPZH
Y
VOH
VOH –0.5 V
1.4 V
0
Figure 4. Enable/Disable Time Test Circuit and Waveforms
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
PARAMETER MEASUREMENT INFORMATION
Table 1. Receiver Minimum and Maximum VIT3
Input Threshold Test Voltages
APPLIED VOLTAGES†
RESULTANT INPUTS
VIA (mV)
–2000
VIB (mV)
–1900
VID (mV)
–100
VIC (mV)
–1950
Output
–2000
–1968
–32
–1984
H
4300
4400
–100
4350
L
4368
4400
–32
4384
H
L
† These voltages are applied for a minimum of 1.5 µs.
VIA
–100 mV @ 250 KHz
VIB
VO
a) No Failsafe
VIA
–32 mV @ 250 KHz
VIB
VO
Failsafe Asserted
b) Failsafe Asserted
Figure 5. VIT3 Failsafe Threshold Test
1.4 V
1V
0.4 V
>1.5 µs
0V
–0.2 V
–0.4 V
td1
td2
VOH
1.4 V
VOL
Figure 6. Waveforms for Failsafe Activate and Deactivate
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
TYPICAL CHARACTERISTICS
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
4
VCC = 3.3 V
TA = 25°C
VOH – High-Level Output Voltage – V
VOL – Low-Level Output Voltage – V
5
4
3
2
1
VCC = 3.3 V
TA = 25°C
3
2
1
0
0
0
10
20
30
–40
40
–30
5
4.5
VCC = 3 V
VCC = 3.3 V
VCC = 3.6 V
3.5
0
50
TA – Free-Air Temperature – °C
HIGH-TO-LOW PROPAGATION DELAY TIME
vs
FREE-AIR TEMPERATURE
t PHL– High-To-Low Propagation Delay Time – ns
t PLH – Low-To-High Propagation Delay Time – ns
LOW-TO-HIGH PROPAGATION DELAY TIME
vs
FREE-AIR TEMPERATURE
100
5
4.5
VCC = 3 V
VCC = 3.3 V
4
VCC = 3.6 V
3.5
3
–50
Figure 9
12
0
Figure 8
Figure 7
3
–50
–10
IOH – High-Level Output Current – mA
IOL – Low-Level Output Current – mA
4
–20
0
50
TA – Free-Air Temperature – °C
Figure 10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
100
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
TYPICAL CHARACTERISTICS
SUPPLY CURRENT
vs
FREQUENCY
140
I CC – Supply Current – mA
120
VCC = 3.3 V
100
80
VCC = 3.6 V
60
VCC = 3 V
40
20
0
0
150
100
200
f – Switching Frequency – MHz
Figure 11
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
APPLICATION INFORMATION
0.01 µF
1
VCC
16
0.1 µF
(see Note A)
1B
100 Ω
2
3
VCC 4
5
6
1A
4B
2Y
4Y
G
2A
100 Ω
7
4A
2B
3Y
3A
5V
1N645
(2 places)
15
1Y
G
≈3.6 V
14
100 Ω
(see Note B)
13
12
11
See Note C
10
100 Ω
8
GND
3B
9
NOTES: A. Place a 0.1-µF Z5U ceramic, mica or polystyrene dielectric, 0805 size, chip capacitor between VCC and the ground plane. The
capacitor should be located as close as possible to the device terminals.
B. The termination resistance value should match the nominal characteristic impedance of the transmission media with ±10%.
C. Unused enable inputs should be tied to VCC or GND as appropriate.
Figure 12. Operation with 5-V Supply
related information
IBIS modeling is available for this device. Please contact the local TI sales office or the TI Web site at www.ti.com
for more information.
For more application guidelines, please see the following documents:
D
D
D
D
D
D
14
Low-Voltage Differential Signalling Design Notes (TI literature number SLLA014)
Interface Circuits for TIA/EIA-644 (LVDS) (SLLA038)
Reducing EMI With LVDS (SLLA030)
Slew Rate Control of LVDS Circuits (SLLA034)
Using an LVDS Receiver With RS-422 Data (SLLA031)
Evaluating the LVDS EVM (SLLA033)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
APPLICATION INFORMATION
terminated failsafe
A differential line receiver commonly has a fail-safe circuit to prevent it from switching on input noise. Current
LVDS fail-safe solutions require either external components with subsequent reduction in signal quality or
integrated solutions with limited application. This family of receivers has a new integrated fail-safe that solves
the limitations seen in present solutions. A detailed theory of operation is presented in application note The
Active Fail-Safe Feature of the SN65LVDS32A, literature number SLLA082.
Figure 13 shows one receiver channel with active fail-safe. It consists of a main receiver that can respond to
a high-speed input differential signal. Also connected to the input pair are two fail-safe receivers that form a
window comparator. The window comparator has a much slower response than the main receiver and detects
when the input differential falls below 80 mV. A 600-ns fail-safe timer filters the window comparator outputs.
When fail-safe is asserted, the fail-safe logic drives the main receiver output to logic high.
Output
Buffer
Main Receiver
A
B
+
_
R
Reset
Failsafe
Timer
A > B + 80 mV
+
_
Failsafe
B > A + 80 mV
+
_
Window Comparator
Figure 13. Receiver With Terminated Failsafe
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
APPLICATION INFORMATION
ECL/PECL-to-LVTTL conversion with TI’s LVDS receiver
The various versions of emitter-coupled logic (i.e. ECL, PECL and LVPECL) are often the physical layer of
choice for system designers. Designers know of the established technology and that it is capable of high-speed
data transmission. In the past, system requirements often forced the selection of ECL. Now technologies like
LVDS provide designers with another alternative. While the total exchange of ECL for LVDS may not be a design
option, designers have been able to take advantage of LVDS by implementing a small resistor divider network
at the input of the LVDS receiver. TI has taken the next step by introducing a wide common-mode LVDS receiver
(no divider network required) which can be connected directly to an ECL driver with only the termination bias
voltage required for ECL termination (VCC – 2 V).
Figures 14 and 15 show the use of an LV/PECL driver driving 5 meters of CAT–5 cable and being received by
TI’s wide common-mode receiver and the resulting eye pattern. The values for R3 are required in order to
provide a resistor path to ground for the LV/PECL driver. With no resistor divider, R1 simply needs to match the
characteristic load impedance of 50 Ω. The R2 resistor is a small value and is intended to minimize any possible
common-mode current reflections.
VCC
ICC
R1 = 50 Ω
R2 = 50 Ω
5 Meters
of CAT-5
LV/PECL
R3
R3
VEE
VB
VB
R1
VCC
ICC
LVDS
R1
R2
R3 = 240 Ω
Figure 14. LVPECL or PECL to Remote Wide Common-Mode LVDS Receiver
Figure 15. LV/PECL to Remote SN65LVDS32B at 500 Mbps Receiver Output (CH1)
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
APPLICATION INFORMATION
test conditions
D
D
D
VCC = 3.3 V
TA = 25°C (ambient temperature)
All four channels switching simultaneously with NRZ data. Scope is pulse-triggered simultaneously with
NRZ data.
equipment
D
D
D
Tektronix PS25216 programmable power supply
Tektronix HFS 9003 stimulus system
Tektronix TDS 784D 4-channel digital phosphor oscilloscope – DPO
Tektronix PS25216
Programmable
Power Supply
Tektronix HFS 9003
Stimulus System
Trigger
Tektronix TDS 784D 4-Channel
Digital Phosphor
Oscilloscope – DPO
Bench Test Board
Figure 16. Equipment Setup
100 Mbit/s
200 Mbit/s
Figure 17. Typical Eye Pattern SN65LVDS32B
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
SN65LVDS32B, SN65LVDT32B, SN65LVDS3486B
SN65LVDT3486B, SN65LVDS9637B, SN65LVDT9637B
HIGH-SPEED DIFFERENTIAL RECEIVERS
SLLS440A – OCTOBER 2000 – REVISED MAY 2001
MECHANICAL DATA
D (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
0.050 (1,27)
0.020 (0,51)
0.014 (0,35)
14
0.010 (0,25) M
8
0.008 (0,20) NOM
0.244 (6,20)
0.228 (5,80)
0.157 (4,00)
0.150 (3,81)
Gage Plane
0.010 (0,25)
1
7
0°– 8°
A
0.044 (1,12)
0.016 (0,40)
Seating Plane
0.069 (1,75) MAX
0.010 (0,25)
0.004 (0,10)
PINS **
0.004 (0,10)
8
14
16
A MAX
0.197
(5,00)
0.344
(8,75)
0.394
(10,00)
A MIN
0.189
(4,80)
0.337
(8,55)
0.386
(9,80)
DIM
4040047 / D 10/96
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
18
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
11-Feb-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
SN65LVDS32BD
ACTIVE
SOIC
D
16
40
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1YEAR/
Level-1-220C-UNLIM
SN65LVDS32BDR
ACTIVE
SOIC
D
16
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1YEAR/
Level-1-220C-UNLIM
SN65LVDS3486BD
ACTIVE
SOIC
D
16
40
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1YEAR/
Level-1-220C-UNLIM
SN65LVDS3486BDR
ACTIVE
SOIC
D
16
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1YEAR/
Level-1-220C-UNLIM
SN65LVDS9637BD
ACTIVE
SOIC
D
8
75
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1YEAR/
Level-1-220C-UNLIM
SN65LVDS9637BDR
ACTIVE
SOIC
D
8
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1YEAR/
Level-1-220C-UNLIM
SN65LVDT32BD
ACTIVE
SOIC
D
16
40
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1YEAR/
Level-1-220C-UNLIM
SN65LVDT32BDR
ACTIVE
SOIC
D
16
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1YEAR/
Level-1-220C-UNLIM
SN65LVDT3486BD
ACTIVE
SOIC
D
16
40
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1YEAR/
Level-1-220C-UNLIM
SN65LVDT3486BDR
ACTIVE
SOIC
D
16
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1YEAR/
Level-1-220C-UNLIM
SN65LVDT9637BD
ACTIVE
SOIC
D
8
75
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1YEAR/
Level-1-220C-UNLIM
SN65LVDT9637BDR
ACTIVE
SOIC
D
8
2500
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1YEAR/
Level-1-220C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional
product content details.
None: Not yet available Lead (Pb-Free).
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens,
including bromine (Br) or antimony (Sb) above 0.1% of total product weight.
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated