Ordering number : ENA0635 LC877816A CMOS IC 16KB-byte and 512-byte RAM 8-bit 1-chip Microcontroller Overview The LC877816A is an 8-bit single chip microcontroller with the following on-chip functional blocks: • CPU: operable at a minimum bus cycle time of 250ns • ROM: 16 Kbytes • RAM: 512 × 9 bits • LCD controller/driver • 16bit timer × 2ch + 8bit timer × 1ch or more • Synchronous serial I/O port (with automatic block transmit/receive function) • Asynchronous/synchronous serial I/O port • System clock divider • 8-bit AD converter × 9-channel • 17-source 10-vectored interrupt system • Power save mode All of the above functions are fabricated on a single chip. Features ROM • 16384 × 8 bits RAM • 512 × 9 bits Minimum Bus Cycle Time • 250ns (4MHz) Note: The bus cycle time indicates ROM read time. Minimum Instruction Cycle Time (tCYC) • 750ns (4MHz) Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. Ver.1.00 51607HKIM 20061017-S00010 No.A0635-1/21 LC877816A Power Save Mode • Power save mode is available, when system clock is RC oscillation or crystal oscillation. Ports • Input/output ports Data direction programmable for each bit individually: 12 (P1n, P70 to P73) Data direction programmable in nibble units: 8 (P0n) (When N-channel open drain output is selected, data can be input in bit units.) • LCD ports Segment output: 24 (S00 to S23) Common output: 4 (COM0 to COM3) Bias terminals for LCD driver 5 (V1 to V3, CUP1, CUP2) Other functions Input/output ports: 8(PCn) • Oscillator pins: 4 (CF1, CF2, XT2, XT1) • Reset pin: 1 (RES) • Power supply: 4 (VSS1 to 2, VDD1 to 2) 1 (VDC) LCD Controller • Seven display modes are available. • Segment output (S16 to S23) can be switched to general purpose input/output ports. • Duty: 1/3duty, 1/4duty • Bias: 1/2bias, 1/3bias • LCD power 1) 1/3bias V1: 1.2V to 1.8V V2: 2.4V to 3.6V V3: 3.6V to 5.4V 2) 1/2bias V1: 1.2V to 1.8V V2: 2.4V to 3.6V V3: 2.4V to 3.6V (connect V2 and V3) Timers • Timer 0: 16 bit timer/counter with capture register Mode 0: 2 channel 8-bit timer with programmable 8 bit prescaler and 8 bit capture register Mode 1: 8 bit timer with 8 bit programmable prescaler and 8 bit capture register + 8 bit counter with 8-bit capture register Mode 2: 16 bit timer with 8 bit programmable prescaler and 16 bit capture register Mode 3: 16 bit counter with 16 bit capture register • Timer 1: PWM/16 bit timer/counter with toggle output function Mode 0: 2 channel 8 bit timer/counter (with toggle output) Mode 1: 2 channel 8 bit PWM Mode 2: 16 bit timer/counter (with toggle output) Toggle output from lower 8 bits is also possible. Mode 3: 16 bit timer (with toggle output) Lower order 8 bits can be used as PWM. • Timer 4: 8-bit timer with 6-bit prescaler • Timer 5: 8-bit timer with 6-bit prescaler • Timer 6: 8-bit timer with 6-bit prescaler (with toggle output) • Timer 7: 8-bit timer with 6-bit prescaler (with toggle output) • Base Timer 1) The clock signal can be selected from any of the following : Sub-clock (32.768kHz crystal oscillator), system clock, and prescaler output from timer 0 2) Interrupts of five different time intervals are possible. No.A0635-2/21 LC877816A SIO • SIO0: 8 bit synchronous serial interface 1) LSB first/MSB first is selectable 2) Internal 8 bit baud-rate generator (fastest clock period 4/3 tCYC) 3) Consecutive automatic data communication (1 to 256 bits) • SIO1: 8 bit asynchronous/synchronous serial interface Mode 0: Synchronous 8 bit serial I/O (2-wire or 3-wire, transmit clock 2 to 512 tCYC) Mode 1: Asynchronous serial I/O (half duplex, 8 data bits, 1 stop bit, baud rate 8 to 2048 tCYC) Mode 2: Bus mode 1 (start bit, 8 data bits, transmit clock 2 to 512 tCYC) Mode 3: Bus mode 2 (start detection, 8 data bits, stop detection) AD Converter: • 8 bits × 9 Channels Remote Control Receiver Circuit (connected to P73/INT3/T0IN terminal) • Noise rejection function (noise rejection filter’s time constant can be selected from 1/32/128 tCYC) Watchdog Timer • Watchdog timer can produce interrupt or system reset. • Watchdog timer has two types. 1) Use an external RC circuit 2) Use the microcontroller’s base timer Interrupts • 17 sources, 10 vectors 1) Three priority (low, high and highest) multiple interrupts are supported. During interrupt handling, an equal or lower priority interrupt request is postponed. 2) If interrupt requests to two or more vector addresses occur at once, the higher priority interrupt takes precedence. In the case of equal priority levels, the vector with the lowest address takes precedence. No. Vector Address Level 1 00003H X or L INT0 Interrupt Source 2 0000BH X or L INT1 3 00013H H or L INT2/T0L 4 0001BH H or L INT3/Base timer 5 00023H H or L T0H 6 0002BH H or L T1L/T1H 7 00033H H or L SIO0 8 0003BH H or L SIO1 9 00043H H or L ADC/T6/T7 10 0004BH H or L Port 0/T4/T5 • Priority levels X > H > L • For equal priority levels, vector with lowest address takes precedence. Subroutine Stack Levels • 256 levels maximum (the stack is allocated in RAM) High-speed Multiplication/Division Instructions • 16 bits × 8 bits (5 tCYC execution time) • 24 bits × 16 bits (12 tCYC execution time) • 16 bits ÷ 8 bits (8 tCYC execution time) • 24 bits ÷ 16 bits (12 tCYC execution time) Oscillation Circuits • On-chip RC oscillation for system clock use. • CF oscillation (4MHz) for system clock use. (Rf built in) • Crystal oscillation (32.768kHz) low speed system clock use. (Rf built in) No.A0635-3/21 LC877816A System Clock Divider Function • Low power consumption operation is available • Minimum instruction cycle time (0.75µs, 1.5µs, 3µs, 6µs, 12µs, 24µs, 48µs, 96µs, 192µs can be switched by program (when using 4MHz main clock) Standby Function • HALT mode: HALT mode is used to reduce power consumption. During the HALT mode, program execution is stopped but peripheral circuits keep operating (some parts of serial transfer operation stop.) 1) Oscillation circuits are not stopped automatically. 2) Released by the system reset or interrupts. • HOLD mode: HOLD mode is used to reduce power consumption. Program execution and peripheral circuits are stopped. 1) CF, RC and crystal oscillation circuits stop automatically. 2) Released by any of the following conditions. (1) Low level input to the reset pin (2) Specified level input to one of INT0, INT1, INT2 (3) Port 0 interrupt • X'tal HOLD mode: X’tal HOLD mode is used to reduce power consumption. Program execution is stopped. All peripheral circuits except the base timer are stopped. 1) CF and RC oscillation circuits stop automatically. 2) Crystal oscillator operation is kept in its state at HOLD mode inception. 3) Released by any of the following conditions (1) Low level input to the reset pin (2) Specified level input to one of INT0, INT1, INT2 (3) Port 0 interrupt (4) Base-timer interrupt Debugger • On chip debugger (LC87F7032A) LC87F7032A and LC877816A differ in following points. When LC87F7032A is power save mode, Current consumption doesn’t decrease. When LC87F7032A is power save mode, X’tal voltage level doesn’t change. LC87F7032A has P2 registers (P2, P2DDR). But, LC877816A doesn’t have them. Package Form • ΤQFP64J(7×7): Lead-free type • QIP64E(14×14): Lead-free type No.A0635-4/21 LC877816A Package Dimensions unit : mm (typ) 3289 9.0 33 32 64 17 7.0 49 1 9.0 48 0.5 7.0 16 0.4 0.125 0.16 0.1 1.2max (1.0) (0.5) SANYO : TQFP64J(7X7) Package unit : mm (typ) 3159A 33 32 64 17 14.0 49 1 17.2 48 0.8 17.2 14.0 16 0.8 0.35 0.15 0.1 3.0max (2.7) (1.0) SANYO : QIP64E(14X14) No.A0635-5/21 LC877816A S08 S09 S10 S11 S12 S13 S14 S15 S16/PC0 S17/PC1 S18/PC2 S19/PC3 S20/PC4 S21/PC5 S22/PC6 S23/PC7 Pin Assignment 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 RES 49 32 S07 XT1 50 31 S06 XT2 51 30 S05 VSS1 52 29 S04 CF1 53 28 S03 CF2 54 27 S02 VDD1 55 26 S01 P00/AN0 56 25 S00 P01/AN1 57 24 COM3 P02/AN2 58 23 COM2 P03/AN3 59 22 COM1 P04/AN4 60 21 COM0 P05/CKO/DBGP0 61 20 V3 P06/T6O/DBGP1 62 19 V2 P07/T7O/DBGP2 63 18 V1 NC 64 17 VDC VSS2 CUP2 VDD2 10 11 12 13 14 15 16 CUP1 P73/INT3/T0IN/AN8 9 P17/T1PWMH P72/INT2/T0IN/AN7 8 P15/SCK1 P71/INT1/T0HCP/AN6 7 P16/T1PWML 6 P14/SI1/SB1 5 P13/SO1 4 P12/SCK0 3 P10/SO0 2 P11/SI0/SB0 1 P70/INT0/T0LCP/AN5 LC877816A Top view SANYO: TQFP64J(7×7) SANYO: QIP64E(14×14) “Lead-free Type” “Lead-free Type” No.A0635-6/21 LC877816A System Block Diagram Interrupt control IR PLA CF RC X’tal Clock generator Standby control ROM PC SIO0 Bus interface SIO1 Port 0 ACC Timer 0 Port 1 B Register Timer 1 Port 7 C Register Timer 4 ADC ALU Timer 5 Timer 6 Timer 7 PSW INT0 to 3 Noise rejection filter RAR Base timer RAM LCD controller Stack pointer Watchdog timer No.A0635-7/21 LC877816A Pin Description Pin name I/O Function Option VSS1, VSS2 - - Power supply VDD1, VDD2 - + Power supply No VDC - + Power supply No CUP1, CUP2 PORT0 I/O P00 to P07 No • Capacitor connecting terminals for step-up/step-down No • 8bit input/output port Yes • Data direction programmable in nibble units • Use of pull-up resistor can be specified in nibble units • Input for HOLD release • Input for port 0 interrupt • Other pin functions Input for ADC channel (AN0 to AN4) P05: Clock output (system clock/subclock) When it’s LC87F7032A, P05 uses as DBGP0. P06: Timer 6 toggle output When it’s LC87F7032A, P06 uses as DBGP1. P07: Timer 7 toggle output When it’s LC87F7032A, P07 uses as DBGP2. PORT1 I/O P10 to P17 Yes • 8bit input/output port • Data direction programmable for each bit • Use of pull-up resistor can be specified for each bit individually • Other pin functions P10: SIO0 data output P11: SIO0 data input or bus input/output P12: SIO0 clock input/output P13: IO1 data output P14: SIO1 data input or bus input/output P15: SIO1 clock input/output P16: Timer 1 PWML output P17: Timer 1 PWMH output/Buzzer output PORT7 I/O P70 to P73 • 4bit Input/output port No • Data direction can be specified for each bit • Use of pull-up resistor can be specified for each bit individually • Other functions P70: INT0 input/HOLD release input/Timer0L capture input/output for watchdog timer/AN5 P71: INT1 input/HOLD release input/Timer0H capture input/AN6 P72: INT2 input/HOLD release input/timer 0 event input/Timer0L capture input/AN7 P73: INT3 input (noise rejection filter attached)/timer 0 event input/Timer0H capture input/AN8 Input for ADC channel (AN5 to AN8) • Interrupt acknowledge type Rising Falling INT0 enable enable INT1 enable enable INT2 enable INT3 enable Rising & H level L level disable enable enable disable enable enable enable enable disable disable enable enable disable disable falling S0 to S15 O • Segment output for LCD No S16/PC0 to I/O • Segment output for LCD No COM0 to COM3 O • Common output for LCD No V1 to V3 I/O • LCD output bias power supply No S23/PC7 • Can be used as general purpose input/output port (PC) • Capacitor connecting terminals for step-up/step-down RES I • Reset terminal No XT1 I • Input for 32.768kHz crystal oscillation No XT2 I/O • When not in use, connect to VDD2 • Output for 32.768kHz crystal oscillation No • When not in use, set to oscillation mode and leave open CF1 I • Input terminal for ceramic oscillator No • When not in use, connect to VDD2 CF2 O • Output terminal for ceramic oscillator No • When not in use, leave open No.A0635-8/21 LC877816A Port Output Types Port form and pull-up resistor options are shown in the following table. Port status can be read even when port is set to output mode. Port Name Option selected in units of Option type P00 to P07 1 bit 1 P10 to P17 1 bit 2 Output type Pull-up resistor CMOS Programmable(Note 1) 2 Nch-open drain No 1 CMOS Programmable Nch-open drain Programmable Programmable P70 - No Nch-open drain P71 to P73 - No CMOS Programmable S16(PC0) to - 1 CMOS, No 2 Pch-Open Drain 3 Nch-Open Drain S23(PC7) Note 1: Attachment of Port0 programmable pull-up resistors is controllable in nibble units (P00 to 03, P04 to 07). *1: Connect as follows to reduce noise on VDD. VSS1 and VSS2 must be connected together and grounded. LSI VDD1 Power supply VDD2 V1 V2 Back up capacitors *2 V3 CUP1 VDC CUP2 VSS1 VSS2 *2: The power supply for the internal memory is VDC. VDD1 and VDD2 are used as the power supply for ports. When VDD1 and VDD2 are not backed up, the port level does not become “H” even if the port latch is in the “H” level. Therefore, when VDD1 and VDD2 are not backed up and the port latch is “H” level, the port level is unstable in the HOLD mode, and the back up time becomes shorter because the through current runs from VDD to GND in the input buffer. If VDD1 and VDD2 are not backed up, output “L” by the program or pull the port to “L” by the external circuit in the HOLD mode so that the port level becomes “L” level and unnecessary current consumption is prevented. No.A0635-9/21 LC877816A Absolute Maximum Ratings at Ta = 25°C, VSS1 = VSS2 = 0V Parameter Symbol Pins/Remarks Specification Conditions VDD[V] Supply voltage VDD max VDD1, VDD2, V2 Supply voltage VLCD For LCD VDD1=VDD2=V2 -0.3 1/2 VDD V2 -0.3 VDD V3 -0.3 3/2 VDD -0.3 VDD+0.3 -0.3 VDD+0.3 Input/Output voltage VIO(1) • Port0, 1, 7 • PortC High level output current Low level output current Ports 0, 1, 7, C -4 Total output ΣIOAH(1) Port 7 Total of all pins -10 current ΣIOAH(2) Port 0 Total of all pins -25 ΣIOAH(3) Port 1 Total of all pins -25 ΣIOAH(4) Port C Total of all pins -15 IOPL(1) Ports 02 to 07 Current at each pin mA 6 Port 1, 7, C IOPL(2) Port 00, 01 Current at each pin 15 Total output ΣIOAL(1) Port 7 Total of all pins 10 current ΣIOAL(2) Port 0 Total of all pins 35 ΣIOAL(3) Port 1 Total of all pins 25 ΣIOAL(4) Port C Total of all pins 15 Pd max TQFP64J(7×7) Ta=-30 to+70°C 200 Allowable power dissipation Operating ambient QIP64E(14×14) Topr temperature Storage ambient temperature Tstg V • CMOS output selected • Current at each pin current current unit V1, XT1, CF1, RES Peak output max +4.3 VI IOPH(1) typ -0.3 Input voltage Peak output min mW 420 -30 +70 -55 +125 °C No.A0635-10/21 LC877816A Allowable Operating Conditions at Ta = -30°C to +70°C, VSS1 = VSS2 = 0V Parameter Symbol Pins/Remarks Specification Conditions VDD Operating VDD(1) supply voltage VDD(2) range VDD(3) VDD(4) Supply VHD VDD1=VDD2=V2 Normal mode min typ max unit 0.37µs≤tCYC≤200µs 3.0 3.6 0.75µs≤tCYC≤200µs 2.4 3.6 VDD1=VDD2=V2 Power save mode 2.25µs≤tCYC≤200µs 3.0 3.6 4.28µs≤tCYC≤200µs 2.4 3.6 VDD1=VDD2=V2 Keep RAM and register data in 2.2 3.6 HOLD mode. voltage range in Hold mode Input high VIH(1) voltage • Ports 1, 71 to 73 Output disable 2.4 to 3.6 • Port 70 input/interrupt VIH(2) VIH(3) • Ports 0, C Port 70 Output disable Output disable Watchdog timer Input low VIH(4) XT1, CF1, RES VIL(1) • Ports 1, 71 to 73 Voltage 2.4 to 3.6 0.3VDD VDD +0.7 0.3VDD +0.7 VDD 2.4 to 3.6 0.9VDD VDD 2.4 to 3.6 0.75VDD VDD 2.4 to 3.6 VSS 0.2VDD 2.4 to 3.6 VSS 2.4 to 3.6 VSS 0.2VDD 0.8VDD 2.4 to 3.6 VSS V Output disable • Port 70 input/interrupt VIL(2) • Ports 0, C Output disable VIL(3) Port 70 Output disable Watchdog timer VIL(4) Operation XT1, CF1, RES tCYC 2.4 to 3.6 cycle time External FEXCF(1) CF1 system clock Oscillation 200 200 2.4 to 3.6 0.1 4 µs MHz • external clock DUTY=50 ± 5% FmCF CF1, CF2 4MHz ceramic resonator frequency oscillation range See fig. 1 (Note 2-1) 2.25 4.28 • CF2 open • system clock divider:1/1 frequency -1.0 0.25VDD FmRC RC oscillation VDD=3.0V, Ta=25°C FsX’tal XT1, XT2 2.4 to 3.6 2.4 to 3.6 4 300 500 MHz 700 kHz 32.768kHz crystal resonator oscillation 2.4 to 3.6 32.768 kHz See fig. 2 Note 2-1: The parts value of oscillation circuit is shown in table 1 and table 2. No.A0635-11/21 LC877816A Electrical Characteristics at Ta = -30°C to +70°C, VSS1 = VSS2 = 0V Parameter Symbol Pins/Remarks Specification Conditions VDD[V] High level IIH(1) input current • Ports 0, 1, 7 • Output disabled • Port C • RES • Pull-up resister OFF. • VIN=VDD min typ max unit 2.4 to 3.6 1 2.4 to 3.6 1 2.4 to 3.6 8 (including OFF state leak current of the output Tr.) IIH(2) XT1, XT2 When configured as an input port VIN=VDD Low level IIH(3) CF1 VIN=VDD IIL(1) • Ports 0, 1, 7 • Output disabled • Port C • RES • Pull-up resister OFF. input current • VIN=VSS 2.4 to 3.6 -1 2.4 to 3.6 -1 µA (including OFF state leak current of the output Tr.) IIL(2) XT1, XT2 When configured as an input port IIL(3) CF1 VIN=VSS VIN=VSS 2.4 to 3.6 -8 VOH(1) Ports 0, 1, 7 IOH=-0.4mA 3.0 to 3.6 VDD-0.4 output CMOS IOH=-0.2mA voltage output option 2.4 to 3.6 VDD-0.4 VDD-0.4 High level Low level VOH(2) Port C IOH=-0.1mA 2.4 to 3.6 VOL(1) Ports 0, 1, 7 IOL=1.6mA 3.0 to 3.6 0.4 IOL=0.8mA 2.4 to 3.6 0.4 IOL=5.0mA 3.0 to 3.6 0.4 IOL=2.5mA 2.4 to 3.6 0.4 0.4 output voltage VOL(2) P00, P01 VOL(3) Port C IOL=0.1mA 2.4 to 3.6 VODLS S0 to S23 voltage IO=0mA V1, V2, V3 2.4 to 3.6 0 ±0.2 regulation LCD level output 2.4 to 3.6 0 ±0.2 2.4 to 3.6 25 LCD output VODLC COM0 to COM3 V IO=0mA V1, V2, V3 LCD level output Resistance Rpu • Ports 0, 1, 7 VOH=0.9VDD of pull-up 50 200 kΩ MOS Tr. Hysterisis VHYS(1) Pin capacitance • Ports 1, 7 2.4 to 3.6 • RES voltage CP All pins 0.1 ×VDD V • All Other Terminals Connected To VSS. • F=4MHz 2.4 to 3.6 10 pF • Ta=25°C No.A0635-12/21 LC877816A Serial I/O Characteristics at Ta = -30°C to +70°C, VSS1 = VSS2 = 0V 1. SIO0 Serial I/O Characteristics (Note 4-1-1) Parameter Symbol Pin/Remarks Specification Conditions Input clock VDD Frequency tSCK(1) Low level tSCKL(1) SCK0(P12) See Fig. 6. tSCKH(1) 2.4 to 3.6 pulse width tSCKHA(1) tCYC 4 • (Note 4-1-2) Frequency tSCK(2) SCK0(P12) • CMOS output selected 4/3 • See Fig. 6. Output clock Low level tSCKL(2) 1/2 pulse width High level tSCK tSCKH(2) 2.4 to 3.6 pulse width tSCKHA(2) 1/2 • Continuous data transmission/reception mode tSCKH(2) • CMOS output selected +2tCYC • See Fig. 6. Data setup time Serial input unit 1 • Continuous data transmission/reception mode tsDI(1) SB0(P11), SI0(P11) tSCKH(2) +(10/3) tCYC tCYC • Must be specified with respect to rising edge of 2.4 to 3.6 0.03 2.4 to 3.6 0.03 SIOCLK. Data hold time Output clock Input clock Output delay Serial output max 1 • See Fig. 6. Serial clock typ 2 pulse width High level min • See Fig. 6. thDI(1) tdD0(1) time SO0(P10), SB0(P11) • Continuous data transmission/reception mode 2.4 to 3.6 • (Note 4-1-3) tdD0(2) • Synchronous 8-bit mode • (Note 4-1-3) tdD0(3) 2.4 to 3.6 (1/3)tCYC +0.05 µs 1tCYC +0.05 • (Note 4-1-3) 2.4 to 3.6 (1/3)tCYC +0.15 Note 4-1-1: These specifications are theoretical values. Add margin depending on its use. Note 4-1-2: To use serial-clock-input in continuous trans/rec mode, a time from SI0RUN being set when serial clock is "H" to the first negative edge of the serial clock must be longer than tSCKHA. Note 4-1-3: Must be specified with respect to falling edge of SIOCLK. Must be specified as the time to the beginning of output state change in open drain output mode. See Fig. 6. No.A0635-13/21 LC877816A 2. SIO1 Serial I/O Characteristics (Note 4-2-1) Parameter Symbol Pin/Remarks Specification Conditions Input clock Frequency tSCK(3) Low level tSCKL(3) SCK1(P15) See Fig. 6. tCYC SCK1(P15) • CMOS output selected 2 • See Fig. 6. tSCKL(4) 2.4 to 3.6 pulse width High level 1/2 tSCK tSCKH(4) 1/2 pulse width Serial input Data setup time unit 1 tSCK(4) Low level max 1 tSCKH(3) Frequency typ 2 2.4 to 3.6 pulse width High level min pulse width Output clock Serial clock VDD SB1(P14), tsDI(2) SI1(P14) • Must be specified with respect to rising edge of 2.4 to 3.6 0.03 2.4 to 3.6 0.03 SIOCLK. Data hold time • See Fig. 6. thDI(2) Output delay time tdD0(4) SO1(P13), Serial output SB1(P14) • Must be specified with µs respect to falling edge of SIOCLK. • Must be specified as the time to the beginning of (1/3)tCYC 2.4 to 3.6 +0.05 output state change in open drain output mode. • See Fig. 6. Note 4-2-1: These specifications are theoretical values. Add margin depending on its use. Pulse Input Conditions at Ta = -30°C to +70°C, VSS1 = VSS2 = 0V Parameter Symbol Pins Specification Conditions VDD[V] High/low tPIH(1) INT0(P70), • Condition that interrupt is accepted level pulse tPIL(1) INT1(P71), • Condition that event input to timer width INT2(P72) INT3(P73) • Condition that interrupt is accepted tPIL(2) (Noise rejection • Condition that event input to timer INT3(P73) • Condition that interrupt is accepted tPIL(3) (Noise rejection • Condition that event input to timer INT3(P73) • Condition that interrupt is accepted tPIL(4) (Noise rejection • Condition that event input to timer tPIL(6) RES 1 2.4 to 3.6 2 max unit tCYC 2.4 to 3.6 64 2.4 to 3.6 256 2.4 to 3.6 200 0 is accepted tPIH(4) ratio is 1/128.) 2.4 to 3.6 0 is accepted tPIH(3) ratio is 1/32.) typ 0 is accepted tPIH(2) ratio is 1/1.) min 0 is accepted • Condition that reset is accepted µs No.A0635-14/21 LC877816A AD Converter Characteristics at Ta = -30°C to +70°C, VSS1 = VSS2 = 0V Parameter Symbol Pin/Remarks Specification Conditions VDD[V] Resolution N AN0(P00) to Absolute ET AN4(P04), accuracy AN5(P70) to Conversion AN8(P73) tCAD time typ max unit 8 (Note 6-1) AD conversion time=32×tCYC (ADCR2=0) (Note 6-2) 3.0 to 3.6 2.4 to 3.6 AD conversion time=32×tCYC (ADCR2=0) (Note6-2) 2.4 to 3.6 Power save mode AD conversion time=64×tCYC (When ADCR2=1) (Note 6-2) 3.0 to 3.6 Normal mode 2.4 to 3.6 AD conversion time=32×tCYC (ADCR2=0) (Note6-2) Power save mode VAIN voltage range Analog port IAINH VAIN=VDD input current IAINL VAIN=VSS bit ±1.5 Normal mode Analog input min 2.4 to 3.6 22.4 640 (tCYC= (tCYC= 0.70µs) 20µs) 128 640 (tCYC= (tCYC= 4.00µs) 20µs) 128 640 (tCYC= (tCYC= 4.00µs) 20µs) 44.8 1280 (tCYC= (tCYC= 0.70µs) 20µs) 256 1280 (tCYC= (tCYC= 4.00µs) 20µs) 256 1280 (tCYC= (tCYC= 4.00µs) 20µs) VSS VDD 1 -1 LSB µs V µA Note 6-1: The quantization error (±1/2LSB) is excluded from the absolute accuracy value. Note 6-2: The conversion time refers to the interval from the time the instruction for starting the converter is issued till the time the complete digital value corresponding to the analog input value is loaded in the required register. No.A0635-15/21 LC877816A Consumption Current Characteristics at Ta = -30°C to +70°C, VSS1 = VSS2 = 0V Parameter Current Symbol IDDOP(1) Pins/ Specification Conditions Remarks VDD[V] • FmCF=4MHz Ceramic resonator oscillation consumption VDD1= VDD2= during normal V2 • System clock: CF 4MHz oscillation min typ max unit • FsX’tal=32.768kHz crystal oscillation operation • Internal RC oscillation stopped. (Note 7-1) • Divider: 1/1 2.4 to 3.6 1100 3200 2.4 to 3.6 150 600 2.4 to 3.6 50 225 2.4 to 3.6 40 180 2.4 to 3.6 15 60 2.4 to 3.6 2.5 17 2.4 to 3.6 1.5 15 2.4 to 3.6 460 1600 2.4 to 3.6 50 300 2.4 to 3.6 35 150 • Normal mode IDDOP(2) • FmCF=0Hz (No oscillation) • FsX’tal=32.768kHz crystal oscillation • System clock: RC oscillation • Divider: 1/1 • Normal mode IDDOP(3) • FmCF=0Hz (No oscillation) • FsX’tal=32.768kHz crystal oscillation • System clock: RC oscillation • Divider: 1/1 • Power save mode IDDOP(4) • FmCF=0Hz (No oscillation) • FsX’tal=32.768kHz crystal oscillation • System clock: RC oscillation • Divider: 1/2 • Power save mode IDDOP(5) • FmCF=0Hz (No oscillation) • FsX’tal=32.768kHz crystal oscillation • System clock: 32.768kHz • Internal RC oscillation stopped. • Divider: 1/1 • Normal mode IDDOP(6) • FmCF=0Hz (No oscillation) • FsX’tal=32.768kHz crystal oscillation • System clock: 32.768kHz • Internal RC oscillation stopped. µA • Divider: 1/1 • Power save mode IDDOP(7) • FmCF=0Hz (No oscillation) • FsX’tal=32.768kHz crystal oscillation • System clock: 32.768kHz • Internal RC oscillation stopped. • Divider: 1/2 • Power save mode Current IDDHALT(1) HALT mode consumption • FmCF=4MHz Ceramic resonator oscillation during HALT • FsX’tal=32.768kHz crystal oscillation mode • System clock: CF 4MHz oscillation (Note 7-1) • Internal RC oscillation stopped. • Divider: 1/1 • Normal mode IDDHALT(2) HALT mode • FmCF=0H (Oscillation stop) • FsX’tal=32.768kHz crystal oscillation • System clock: RC oscillation • Divider: 1/1 • Normal mode IDDHALT(3) HALT mode • FmCF=0H (Oscillation stop) • FsX’tal=32.768kHz crystal oscillation • System clock: RC oscillation • Divider: 1/1 • Power save mode Note 7-1: The currents through the output transistors and the pull-up MOS transistors are ignored. Continued on next page. No.A0635-16/21 LC877816A Continued from preceding page. Parameter Current Symbol IDDHALT(4) Pins/ Specification Conditions Remarks VDD[V] min typ max unit HALT mode consumption VDD1= VDD2= • FmCF=0H (Oscillation stop) during HALT V2 • FsX’tal=32.768kHz crystal oscillation mode • System clock: RC oscillation (Note 7-1) • Divider: 1/2 2.4 to 3.6 30 135 2.4 to 3.6 7.0 60 2.4 to 3.6 1.0 15 2.4 to 3.6 0.8 14 2.4 to 3.6 0.03 30 2.4 to 3.6 5.0 45 2.4 to 3.6 0.5 15 • Power save mode IDDHALT(5) HALT mode • FmCF=0Hz (Oscillation stop) • FsX’tal=32.768kHz crystal oscillation • System clock: 32.768kHz • Internal RC oscillation stopped. • Divider: 1/1 • Normal mode IDDHALT(6) HALT mode • FmCF=0Hz (Oscillation stop) • FsX’tal=32.768kHz crystal oscillation • System clock: 32.768kHz • Internal RC oscillation stopped. • Divider: 1/1 • Power save mode IDDHALT(7) HALT mode • FmCF=0Hz (Oscillation stop) • FsX’tal=32.768kHz crystal oscillation • System clock: 32.768kHz µA • Internal RC oscillation stopped. • Divider: 1/2 • Power save mode Current IDDHOLD(1) HOLD mode • CF1=VDD or open consumption (when using external clock) during HOLD mode Current IDDHOLD(2) Date/time clock consumption HOLD mode during • CF1=VDD or open Date/time (when using external clock) X’tal HOLD • FmX’tal=32.768kHz crystal oscillation mode • Internal RC oscillation stopped. • Divider: 1/1 • Normal mode IDDHOLD(3) Date/time clock HOLD mode • CF1=VDD or open (when using external clock) • FmX’tal=32.768kHz crystal oscillation • Internal RC oscillation stopped. • Divider: 1/1 • Power save mode Note 7-1: The currents through the output transistors and the pull-up MOS transistors are ignored. No.A0635-17/21 LC877816A Main System Clock Oscillation Circuit Characteristics The characteristics in the table bellow is based on the following conditions: Use the standard evaluation board SANYO has provided. Use the peripheral parts with indicated value externally. The peripheral parts value is a recommended value of oscillator manufacturer Table 1. Main system clock oscillation circuit characteristics using ceramic resonator Circuit parameters Frequency 4.00MHz Manufacturer Murata Type Oscillator C1 C2 Rd Operating supply voltage range[V] Oscillation stabilizing time typ max [ms] [ms] [pF] [pF] [Ω] SMD CSTCR4M00G53-R0 (15) (15) 1k 2.4 to 3.6 0.2 0.6 Lead CSTLS4M00G53-B0 (15) (15) 2.2k 2.4 to 3.6 0.2 0.6 Notes The oscillation stabilizing time is a period until the oscillation becomes stable after VDD becomes higher than minimum operating voltage. (See Fig. 4) Subsystem Clock Oscillation Circuit Characteristics The characteristics in the table bellow is based on the following conditions: Use the standard evaluation board SANYO has provided. Use the peripheral parts with indicated value externally. The peripheral parts value is a recommended value of oscillator manufacturer Table 2. Subsystem clock oscillation circuit characteristics using crystal oscillator Circuit parameters Frequency Manufacturer Oscillator 32.768kHz Epson Toyocom MC-146 C3 C4 [pF] 10 Operating Oscillation supply stabilizing time voltage range typ max [Ω] [V] [s] [s] 0 2.4 to 3.6 1 3 Rf Rd2 [pF] [Ω] 10 Open Notes The oscillation stabilizing time is a period until the oscillation becomes stable after executing the instruction which starts the sub-clock oscillation or after releasing the HOLD mode. (See Fig. 4) Notes: Since the circuit pattern affects the oscillation frequency, place the oscillation-related parts as close to the oscillation pins as possible with the shortest possible pattern length. CF1 XT1 CF2 Rd C1 CF C2 XT2 Rf C3 Rd2 C4 X’tal Figure 1 Ceramic Oscillation Circuit Figure 2 Crystal Oscillation Circuit 0.5VDD Figure 3 AC Timing Measurement Point No.A0635-18/21 LC877816A VDD Power Supply VDD limit 0V Reset time RES Internal RC Resonator oscillation tmsCF CF1, CF2 tmsX’tal XT1, XT2 Operation mode Unfixed Reset Instruction execution Reset Time and Oscillation Stabilization HOLD release signal Without HOLD Release signal HOLD release signal Internal RC Resonator oscillation tmsCF CF1, CF2 tmsX’tal XT1, XT2 Operation mode HOLD HALT HOLD Release Signal and Oscillation Stabilization Figure 4 Oscillation Stabilizing Time No.A0635-19/21 LC877816A VDD Note: Select CRES and RRES value to assure that at least 200µs reset time is generated after the VDD becomes higher than the minimum operating voltage. RRES RES CRES Figure 5 Reset Circuit SIOCLK: DATAIN: DI0 DI1 DI2 DI3 DI4 DI5 DI6 DI7 DI8 DATAOUT: DO0 DO1 DO2 DO3 DO4 DO5 DO6 DO7 DO8 Data RAM transfer period (only SIO0) tSCK tSCKL tSCKH SIOCLK: tsDI thDI DATAIN: tdDO DATAOUT: Data RAM transfer period (only SIO0) tSCKL tSCKHA SIOCLK: tsDI thDI DATAIN: tdDO DATAOUT: Figure 6 Serial Input/Output Wave Form No.A0635-20/21 LC877816A tPIL tPIH Figure 7 Pulse Input Timing Signal Waveform SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of September, 2006. Specifications and information herein are subject to change without notice. PS No.A0635-21/21