STF15NM65N-STI15NM65N-STW15NM65N STB15NM65N-STP15NM65N N-channel 650V - 0.25Ω - 15.5A - TO-220/FP - D2/I2PAK - TO-247 Second generation MDmesh™ Power MOSFET Features VDSS RDS(on) Max (@Tjmax) Type ID 3 12 3 STB15NM65N 710 V < 0.27 Ω 15.5 A STF15NM65N 710 V < 0.27 Ω 15.5 A(1) STI15NM65N 710 V < 0.27 Ω 15.5 A 1 2 I²PAK TO-220 3 1 STP15NM65N 710 V < 0.27 Ω 15.5 A STW15NM65N 710 V < 0.27 Ω 15.5 A 2 TO-220FP 1. Limited only by maximum temperature allowed 3 1 2 ■ 100% avalanche tested ■ Low input capacitance and gate charge ■ Low gate input resistance D²PAK Figure 1. 3 1 TO-247 Internal schematic diagram Application ■ Switching applications Description This series of devices implements the second generation of MDmesh™ Technology. This revolutionary Power MOSFET associates a new vertical structure to the Company’s strip layout to yield one of the world’s lowest on-resistance and gate charge. It is therefore suitable for the most demanding high efficiency converters Table 1. Device summary Order codes Marking Package Packaging STI15NM65N 15NM65N I²PAK Tube STF15NM65N 15NM65N TO-220FP Tube STP15NM65N 15NM65N TO-220 Tube STB15NM65NT4 15NM65N D²PAK Tape & reel STW15NM65N 15NM65N TO-247 Tube September 2007 Rev 1 1/18 www.st.com 18 Contents STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 Electrical characteristics (curves) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 Test circuit 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2/18 ................................................ 9 STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N 1 Electrical ratings Electrical ratings Table 2. Absolute maximum ratings Value Symbol Parameter TO-220/I²PAK TO-220FP D²PAK/TO-247 Unit VDS Drain-source voltage (VGS=0) 650 V VGS Gate-source voltage ± 25 V ID Drain current (continuous) at TC = 25°C 15.5 15.5(1) A ID Drain current (continuous) at TC = 100°C 10 10(1) A IDM (2) Drain current (pulsed) 62 62(1) A PTOT Total dissipation at TC = 25°C 150 35 W dv/dt (3) VISO Tj Tstg Peak diode recovery voltage slope Insulation withstand voltage (RMS) from all three leads to external heat sink (t=1s;TC=25°C) Operating junction temperature Storage temperature 15 -- V/ns 2500 -55 to 150 V °C 1. Limited only by maximum temperature allowed 2. Pulse width limited by safe operating area 3. ISD ≤15.5A, di/dt ≤400A/µs, VDD = 80% V(BR)DSS Table 3. Thermal data Value Symbol Parameter TO-220/I²PAK TO-220FP D²PAK/TO-247 Rthj-case Thermal resistance junction-case Max Rthj-amb Thermal resistance junction-amb Max 62.5 °C/W Maximum lead temperature for soldering purpose 300 °C Max value Unit 4 A 400 mJ Tl Table 4. Symbol 0.83 3.6 Unit °C/W Avalanche characteristics Parameter IAS Avalanche current, repetitive or not-repetitive (pulse width limited by Tj max) EAS Single pulse avalanche energy (starting Tj=25 °C, ID= IAS, VDD= 50 V) 3/18 Electrical characteristics 2 STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N Electrical characteristics (TCASE=25°C unless otherwise specified) Table 5. Symbol On/off states Parameter Test conditions Min. Typ. Max. Unit V(BR)DSS Drain-source breakdown voltage ID = 1 mA, VGS = 0 dv/dt (1) Drain source voltage slope Vdd=520 V, Id=15.5 A, Vgs=10 V IDSS Zero gate voltage drain current (VGS = 0) VDS = Max rating VDS = Max rating, @125 °C 1 100 µA µA IGSS Gate-body leakage current (VDS = 0) VGS = ± 20 V ±100 nA VGS(th) Gate threshold voltage VDS = VGS, ID = 250 µA 3 4 V RDS(on) Static drain-source on resistance VGS = 10 V, ID = 7.75 A 0.25 0.27 Ω Typ. Max. Unit 650 V 30 2 V/ns 1. Characteristics value at turn off on inductive load Table 6. Symbol Dynamic Parameter Test conditions Min. gfs (1) Forward transconductance VDS=15 V, ID =7.75 A 15 S Ciss Coss Crss Input capacitance Output capacitance Reverse transfer capacitance VDS = 50 V, f = 1 MHz, VGS = 0 1900 110 10 pF pF pF Equivalent output capacitance VGS = 0 V, VDS = 0V to 520 V 230 pF Total gate charge Gate-source charge Gate-drain charge VDD = 520 V, ID = 15.5 A, VGS = 10 V, (see Figure 19) 55 9 30 nC nC nC Coss eq.(2) Qg Qgs Qgd 1. Pulsed: pulse duration = 300µs, duty cycle 1.5% 2. Coss eq. is defined as a constant equivalent capacitance giving the same charging time as Coss when VDS increases from 0 to 80% VDSS 4/18 STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N Table 7. Symbol td(on) tr td(off) tf Table 8. Symbol ISD ISDM (1) VSD (2) trr Qrr IRRM trr Qrr IRRM Electrical characteristics Switching times Parameter Turn-on delay time Rise time Turn-off delay time Fall time Test conditions Min Typ Max 25 8 80 26 VDD =325 V, ID = 7.75 A RG = 4.7 Ω VGS = 10 V (see Figure 18) Unit ns ns ns ns Source drain diode Parameter Test conditions Min Typ Source-drain current Source-drain current (pulsed) Max Unit 15.5 62 A A 1.3 V Forward on voltage ISD = 15.5 A, VGS = 0 Reverse recovery time Reverse recovery charge Reverse recovery current ISD = 15.5 A, di/dt = 100 A/µs VDD = 100 V, Tj = 25 °C (see Figure 20) 460 6 27 ns µC A Reverse recovery time Reverse recovery charge Reverse recovery current ISD = 15.5 A, di/dt = 100 A/µs VDD = 100 V, Tj = 150°C (see Figure 20) 600 8 27 ns µC A 1. Pulse width limited by safe operating area 2. Pulsed: pulse duration = 300µs, duty cycle 1.5% 5/18 Electrical characteristics STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N 2.1 Electrical characteristics (curves) Figure 2. Safe operating area for TO-220 D2PAK - I2PAK Figure 3. Thermal impedance for TO-220 D2PAK - I2PAK Figure 4. Safe operating area for TO-220FP Figure 5. Thermal impedance for TO-220FP Figure 6. Safe operating area for TO-247 Figure 7. Thermal impedance for TO-247 6/18 STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N Figure 8. Output characteristics Figure 10. Transconductance Figure 9. Electrical characteristics Transfer characteristics Figure 11. Static drain-source on resistance Figure 12. Gate charge vs gate-source voltage Figure 13. Capacitance variations 7/18 Electrical characteristics STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N Figure 14. Normalized gate threshold voltage vs temperature Figure 15. Normalized on resistance vs temperature Figure 16. Source-drain diode forward characteristics Figure 17. Normalized BVDSS vs temperature 8/18 STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N 3 Test circuit Test circuit Figure 18. Switching times test circuit for resistive load Figure 19. Gate charge test circuit Figure 20. Test circuit for inductive load Figure 21. Unclamped Inductive load test switching and diode recovery times circuit Figure 22. Unclamped inductive waveform Figure 23. Switching time waveform 9/18 Package mechanical data 4 STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 10/18 STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N Package mechanical data TO-220 mechanical data mm inch Dim Min A b b1 c D D1 E e e1 F H1 J1 L L1 L20 L30 ∅P Q Typ 4.40 0.61 1.14 0.49 15.25 Max Min 4.60 0.88 1.70 0.70 15.75 0.173 0.024 0.044 0.019 0.6 10.40 2.70 5.15 1.32 6.60 2.72 14 3.93 0.393 0.094 0.194 0.048 0.244 0.094 0.511 0.137 1.27 10 2.40 4.95 1.23 6.20 2.40 13 3.50 Max 0.181 0.034 0.066 0.027 0.62 0.050 16.40 28.90 3.75 2.65 Typ 0.409 0.106 0.202 0.051 0.256 0.107 0.551 0.154 0.645 1.137 3.85 2.95 0.147 0.104 0.151 0.116 11/18 Package mechanical data STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N TO-220FP mechanical data mm. DIM. MIN. A 4.4 inch TYP MAX. MIN. TYP. 4.6 0.173 0.181 MAX. 0.106 B 2.5 2.7 0.098 D 2.5 2.75 0.098 0.108 E 0.45 0.7 0.017 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.7 0.045 0.067 F2 1.15 1.7 0.045 0.067 0.204 G 4.95 5.2 0.195 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 L2 16 0.630 L3 28.6 30.6 1.126 1.204 L4 9.8 10.6 .0385 0.417 L5 2.9 3.6 0.114 0.141 L6 15.9 16.4 0.626 0.645 9 9.3 0.354 0.366 Ø 3 3.2 0.118 0.126 B D A E L7 L3 L6 F2 H G G1 F F1 L7 L2 12/18 L5 1 23 L4 STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N Package mechanical data TO-262 (I2PAK) mechanical data mm. inch DIM. MAX. MIN. A 4.40 MIN. TYP 4.60 0.173 TYP. MAX. A1 2.40 2.72 0.094 0.107 b 0.61 0.88 0.024 0.034 b1 1.14 1.70 0.044 0.066 c 0.49 0.70 0.019 0.027 c2 1.23 1.32 0.048 0.052 D 8.95 9.35 0.352 0.368 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.194 0.202 E 10 10.40 0.393 0.410 0.181 L 13 14 0.511 0.551 L1 3.50 3.93 0.137 0.154 L2 1.27 1.40 0.050 0.055 13/18 Package mechanical data STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N D²PAK mechanical data mm inch Dim Min A A1 A2 B B2 C C2 D D1 E E1 G L L2 L3 M R V2 14/18 Typ 4.4 2.49 0.03 0.7 1.14 0.45 1.23 8.95 Max Min 4.6 2.69 0.23 0.93 1.7 0.6 1.36 9.35 0.173 0.098 0.001 0.027 0.044 0.017 0.048 0.352 10.4 0.393 8 10 0.181 0.106 0.009 0.036 0.067 0.023 0.053 0.368 0.409 0.334 5.28 15.85 1.4 1.75 3.2 0.4 0° Max 0.315 8.5 4.88 15 1.27 1.4 2.4 Typ 0.192 0.590 0.50 0.055 0.094 0.208 0.625 0.55 0.68 0.126 0.015 4° STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N Package mechanical data TO-247 MECHANICAL DATA DIM. mm. MIN. TYP inch MAX. MIN. TYP. MAX. A 4.85 5.15 0.19 0.20 A1 2.20 2.60 0.086 0.102 b 1.0 1.40 0.039 0.055 b1 2.0 2.40 0.079 0.094 0.134 b2 3.0 3.40 0.118 c 0.40 0.80 0.015 0.03 D 19.85 20.15 0.781 0.793 E 15.45 15.75 0.608 e 5.45 0.620 0.214 L 14.20 14.80 0.560 0.582 L1 3.70 4.30 0.14 0.17 L2 18.50 0.728 øP 3.55 3.65 0.140 0.143 øR 4.50 5.50 0.177 0.216 S 5.50 0.216 15/18 Packaging mechanical data 5 STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N Packaging mechanical data D2PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA DIM. mm MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 B0 15.7 15.9 0.618 0.626 D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 F 11.4 11.6 0.449 0.456 MAX. K0 4.8 5.0 0.189 0.197 P0 3.9 4.1 0.153 0.161 P1 11.9 12.1 0.468 0.476 P2 1.9 2.1 0.075 0.082 R 50 1.574 T 0.25 0.35 0.0098 0.0137 W 23.7 24.3 * on sales type 16/18 inch 0.933 0.956 inch MAX. MIN. MAX. 330 12.992 13.2 0.504 0.520 26.4 0.960 1.039 0.059 0795 3.937 30.4 1.197 BASE QTY BULK QTY 1000 1000 STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N 6 Revision history Revision history Table 9. Document revision history Date Revision 06-Sep-2007 1 Changes First release 17/18 STB15NM65N-STI15NM65N-STF15NM65N-STP/W15NM65N Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 18/18