STB13NM50N/-1 - STF13NM50N STP13NM50N - STW13NM50N N-channel 500V - 0.250Ω - 12A - TO-220/FP - TO-247-I2/D2PAK Second generation MDmesh™ Power MOSFET Features Type VDSS (@Tjmax) RDS(on) ID STB13NM50N 550V <0.32Ω 12A STB13NM50N-1 550V <0.32Ω 12A STF13NM50N 550V <0.32Ω 12A(1) STP13NM50N 550V <0.32Ω 12A STW13NM50N 550V <0.32Ω 12A 3 1 3 12 2 TO-220 I²PAK TO-247 3 1 1. Limited only by maximum temperature allowed TO-220FP ■ 100% avalanche tested ■ Low input capacitance and gate charge ■ Low gate input resistance 3 2 1 D²PAK Internal schematic diagram Description This product is realized with the second generation of MDmesh™ technology. This revolutionary Power MOSFET associates a new vertical structure to the company’s strip layout to yield one of the world’s lowest on-resistance and gate charge. It is therefore suitable for the most demanding high efficiency converters Application ■ Switching application Order codes Part number Marking Package Packaging STB13NM50N-1 B13NM50N I²PAK Tube STB13NM50N B13NM50N D²PAK Tape & reel STP13NM50N P13NM50N TO-220 Tube STF13NM50N F13NM50N TO-220FP Tube STW13NM50N W13NM50N TO-247 Tube May 2007 Rev 2 1/17 www.st.com 17 Contents STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 Electrical characteristics (curves) ............................ 6 3 Test circuit 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2/17 ............................................... 9 STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N 1 Electrical ratings Electrical ratings Table 1. Absolute maximum ratings Value Symbol Parameter Unit TO-220/TO-247 D²PAK/I²PAK TO-220FP VDS Drain-source voltage (VGS=0) 500 V VGS Gate-source voltage ± 25 V ID Drain current (continuous) at TC = 25°C 12 12 (1) A ID Drain current (continuous) at TC = 100°C 6 6 (1) A IDM (2) Drain current (pulsed) 48 48 (1) A PTOT Total dissipation at TC = 25°C 100 25 W dv/dt (3) VISO Tj Tstg Peak diode recovery voltage slope Insulation withstand voltage (RMS) from all three leads to external heat sink (t=1s;TC=25°C) 15 V/ns -- Operating junction temperature Storage temperature 2500 -55 to 150 V °C 1. Limited only by maximum temperature allowed 2. Pulse width limited by safe operating area 3. ISD ≤12A, di/dt ≤400A/µs, VDD =80% V(BR)DSS Table 2. Thermal data Value Symbol Parameter Unit TO-220/TO-247 D²PAK/I²PAK TO-220FP 1.25 5 Rthj-case Thermal resistance junction-case max Rthj-amb Thermal resistance junction-amb max 62.5 °C/W Maximum lead temperature for soldering purpose 300 °C Tl Table 3. °C/W Avalanche characteristics Symbol Parameter Max value Unit IAS Avalanche current, repetitive or notrepetitive (pulse width limited by Tj max) 3.5 A EAS Single pulse avalanche energy (starting Tj=25°C, ID=IAS, VDD= 50V) 200 mJ 3/17 Electrical characteristics 2 STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N Electrical characteristics (TCASE=25°C unless otherwise specified) Table 4. Symbol V(BR)DSS dv/dt(1) 1. Parameter Test conditions Drain-source breakdown voltage ID = 1mA, VGS= 0 Drain-source voltage slope Vdd=400V,Id=12A, Vgs=10V Min. Typ. Max. Unit 500 V 30 VDS = Max rating, V/ns VDS = Max rating,Tc=125°C 1 100 µA µA Gate body leakage current (VDS = 0) VGS = ±20V 100 nA VGS(th) Gate threshold voltage VDS= VGS, ID = 250µA 3 4 V RDS(on) Static drain-source on resistance VGS= 10V, ID= 6A 0.25 0.32 Ω Typ. Max. Unit IDSS Zero gate voltage drain current (VGS = 0) IGSS 2 Characteristics value at turn off on inductive load Table 5. Symbol Dynamic Parameter Test conditions gfs(1) Forward transconductance VDS =15V, ID= 6A Ciss Input capacitance Output capacitance Reverse transfer capacitance Min. 8 S VDS =50V, f=1MHz, VGS=0 960 50 5 pF pF pF Equivalent output capacitance VGS=0, VDS =0V to 480V 110 pF Rg Gate input resistance f=1MHz Gate DC Bias=0 test signal level=20mV open drain 5 Ω Qg Total gate charge Gate-source charge Gate-drain charge 30 5 15 nC nC nC Coss Crss Coss eq.(2) Qgs Qgd 1. On/off states VDD=400V, ID = 12A VGS =10V (see Figure 18) Pulsed: pulse duration = 300µs, duty cycle 1.5% 2. Coss eq. is defined as a constant equivalent capacitance giving the same charging time as Coss when VDS increases from 0 to 80% VDSS 4/17 STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N Table 6. Symbol td(on) tr td(off) tf Table 7. Symbol ISD Switching times Parameter Turn-on delay time Rise time Turn-off delay time Fall time Test conditions RG=4.7Ω, VGS=10V Parameter Test conditions Forward on voltage ISD=12A, VGS=0 Reverse recovery time Reverse recovery charge Reverse recovery current ISD=12A, VDD=100V trr Qrr IRRM Max. Unit ns ns ns ns Source drain diode VSD(2) IRRM Typ. 30 15 40 10 (see Figure 17) Source-drain current Source-drain current (pulsed) Qrr Min. VDD=250V, ID=6A, ISDM (1) trr Electrical characteristics Reverse recovery time Reverse recovery charge Reverse recovery current di/dt = 100A/µs,Tj=25°C (see Figure 19) ISD=12A,VDD=100V di/dt=100A/µs,Tj=150°C (see Figure 19) Min Typ. Max Unit 12 48 A A 1.3 V 300 3 22 ns µC A 370 4 22 ns µC A 1. Pulse width limited by safe operating area 2. Pulsed: pulse duration = 300µs, duty cycle 1.5% 5/17 Electrical characteristics STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N 2.1 Electrical characteristics (curves) Figure 1. Safe operating area for TO-220 / D²PAK / I²PAK Figure 2. Thermal impedance for TO-220 / D²PAK / I²PAK Figure 3. Safe operating area for TO-220FP Figure 4. Thermal impedance for TO-220FP Figure 5. Safe operating area for TO-247 Figure 6. Thermal impedance for TO-247 6/17 STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N Electrical characteristics Figure 7. Output characteristics Figure 8. Transfer characteristics Figure 9. Transconductance Figure 10. Static drain-source on resistance Figure 11. Gate charge vs gate-source voltage Figure 12. Capacitance variations 7/17 Electrical characteristics STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N Figure 13. Normalized gate threshold voltage vs temperature Figure 14. Normalized on resistance vs temperature Figure 15. Source-drain diode forward characteristics Figure 16. Normalized BVdss vs temperature 8/17 STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N 3 Test circuit Test circuit Figure 17. Switching times test circuit for resistive load Figure 18. Gate charge test circuit Figure 19. Test circuit for inductive load Figure 20. Unclamped inductive load test switching and diode recovery times circuit Figure 21. Unclamped inductive waveform Figure 22. Switching time waveform 9/17 Package mechanical data 4 STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 10/17 STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N Package mechanical data TO-220 mechanical data mm inch Dim Min A b b1 c D D1 E e e1 F H1 J1 L L1 L20 L30 ∅P Q Typ 4.40 0.61 1.14 0.49 15.25 Max Min 4.60 0.88 1.70 0.70 15.75 0.173 0.024 0.044 0.019 0.6 10.40 2.70 5.15 1.32 6.60 2.72 14 3.93 0.393 0.094 0.194 0.048 0.244 0.094 0.511 0.137 1.27 10 2.40 4.95 1.23 6.20 2.40 13 3.50 Max 0.181 0.034 0.066 0.027 0.62 0.050 16.40 28.90 3.75 2.65 Typ 0.409 0.106 0.202 0.051 0.256 0.107 0.551 0.154 0.645 1.137 3.85 2.95 0.147 0.104 0.151 0.116 11/17 Package mechanical data STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N TO-220FP MECHANICAL DATA mm. DIM. MIN. A 4.4 inch TYP MAX. MIN. TYP. 4.6 0.173 0.181 MAX. 0.106 B 2.5 2.7 0.098 D 2.5 2.75 0.098 0.108 E 0.45 0.7 0.017 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.7 0.045 0.067 F2 1.15 1.7 0.045 0.067 G 4.95 5.2 0.195 0.204 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 L2 16 0.630 L3 28.6 30.6 1.126 1.204 L4 9.8 10.6 .0385 0.417 L5 2.9 3.6 0.114 0.141 L6 15.9 16.4 0.626 0.645 9 9.3 0.354 0.366 Ø 3 3.2 0.118 0.126 B D A E L7 L3 L6 F2 H G G1 F F1 L7 L2 12/17 L5 1 2 3 L4 STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N Package mechanical data TO-262 (I2PAK) MECHANICAL DATA mm. inch DIM. MAX. MIN. A 4.40 MIN. TYP 4.60 0.173 TYP. MAX. A1 2.40 2.72 0.094 0.107 b 0.61 0.88 0.024 0.034 0.181 b1 1.14 1.70 0.044 0.066 c 0.49 0.70 0.019 0.027 c2 1.23 1.32 0.048 0.052 D 8.95 9.35 0.352 0.368 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.194 0.202 E 10 10.40 0.393 0.410 L 13 14 0.511 0.551 L1 3.50 3.93 0.137 0.154 L2 1.27 1.40 0.050 0.055 13/17 Package mechanical data STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N D2PAK MECHANICAL DATA TO-247 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 4.4 4.6 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.7 0.93 0.027 0.036 B2 1.14 1.7 0.044 0.067 C 0.45 0.6 0.017 0.023 C2 1.23 1.36 0.048 0.053 D 8.95 9.35 0.352 0.368 10.4 0.393 D1 E 8 10 E1 0.315 8.5 0.334 G 4.88 5.28 0.192 0.208 L 15 15.85 0.590 0.625 L2 1.27 1.4 0.050 0.055 L3 1.4 1.75 0.055 0.068 M 2.4 3.2 0.094 R 0º 0.126 0.015 4º 3 V2 0.4 1 14/17 STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N 5 Packaging mechanical data Packaging mechanical data D2PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA DIM. mm inch MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 B0 15.7 15.9 0.618 0.626 D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 F 11.4 11.6 0.449 0.456 K0 4.8 5.0 0.189 0.197 P0 3.9 4.1 0.153 0.161 P1 11.9 12.1 0.468 0.476 P2 1.9 2.1 0.075 0.082 inch MAX. MIN. MAX. 330 12.992 13.2 0.504 0.520 26.4 0.960 1.039 0.059 0795 3.937 30.4 1.197 BASE QTY BULK QTY 1000 1000 MAX. R 50 1.574 T 0.25 0.35 0.0098 0.0137 W 23.7 24.3 0.933 0.956 * on sales type 15/17 Revision history 6 STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N Revision history Table 8. 16/17 Revision history Date Revision Changes 18-Dec-2006 1 First release 08-May-2007 2 Added TO-247 STB13NM50N/-1 - STF13NM50N - STP13NM50N - STW13NM50N Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 17/17