VNQ860-E VNQ860SP-E QUAD CHANNEL HIGH SIDE DRIVER General Features Type RDS(ON)(1) Iout VCC 270mΩ 0.25A 36V VNQ860-E VNQ860SP-E SO- 20 PowerSO-10TM Note: 1 Per each channel. ■ CMOS COMPATIBLE I/Os Description ■ UNDERVOLTAGE & OVERVOLTAGE The VNQ860-E, VNQ860SP-E are monolithic devices made using STMicroelectronics VIPower M0-3 Technology, intended for driving any kind load with one side connected to ground. Active current limitation combined with thermal shutdown and automatic restart protect the device against overload. Device automatically turns OFF in case of ground pin disconnection. This device is especially suitable for industrial applications in norms conformity with IEC 61131, (Programmable Controllers International Standard). __-SHUT-DOWN ■ SHORTED LOAD PROTECTION ■ THERMAL SHUT-DOWN ■ VERY LOW STAND-BY CURRENT ■ PROTECTION AGAINST LOSS OF GROUND Block Diagram Order Codes Package Tube Tape and Reel SO-20 VNQ860 VNQ86013TR-E PowerSO-10TM VNQ860SP VNQ860SP13TR-E November 2005 Rev 2 1/15 www.st.com 15 VNQ860-E / VNQ860SP-E Table 1. Absolute Maximum Rating Value Symbol Parameter Unit SO-20 PowerSO-10 VCC DC supply voltage 41 V -0.3 V -VCC Reverse DC supply voltage -IGND DC reverse ground pin IOUT DC output current -IOUT Reverse DC output current IIN VIN -200 mA Internally limited A -2 A ± 10 mA V DC Input current Input voltage range -3/+V CC ISTAT DC Status voltage + VCC V VESD Electrostatic discharge (R = 1.5KW; C = 100pF) 2000 V Ptot Power dissipation at Tc <= 25°C TJ Junction operating temperature Tc Case operating temperature -40 to 150 °C Storage Temperature -55 to 150 °C Tstg Figure 1. 90 W Internally limited °C Configuration Diagram(Top View) & Suggested Connections for Unused and N.C. Pins Connection / pin Floating To Ground 2/15 16 Status N.C. Output Input X X X X X Through 10KΩ resistor VNQ860-E / VNQ860SP-E Figure 2. Current and Voltage Conventions Table 2. Thermal data Max Value Symbol Parameter Unit SO-20 Rthj-pin Thermal resistance junction-pins Max 8 RthJA Thermal resistance junction-ambient Max 58 RthJC Thermal resistance junction-case Max - PowerSO-10 52 Note 1 37 Note 2 1.4 °C/W °C/W °C/W 1.When mounted on FR4 printed circuit board with 0.5cm2 of copper area ( at least 35µ thick ) connected to all VCC pins. 2.When mounted on FR4 printed circuit board with 6cm2 of copper area ( at least 35µ thick ) connected to all VCC pins. 3/15 VNQ860-E / VNQ860SP-E Electrical Characteristics (8V < VCC < 36V; -40°C < TJ < 150°C; unless otherwise specified) Table 3. Symbol Power Section Parameter Test Conditions Min. Typ. Max. Unit VCC Operating supply voltage 5.5 36 V VUSD Undervoltage shut-down 3 4 5.5 V VOV Overvoltage shut-down 36 42 48 V RON On state resistance (per channel) 270 540 mΩ IS Supply current 120 10 µΑ mA ILGND Output current 1 mA IL(OFF) OFF state output current VIN = VOUT = 0V 10 µΑ 240 µΑ 100 µΑ Max. Unit IOUT = 0.25A; TJ = 25°C; IOUT = 0.25A; OFF state; VCC = 24V; TC = 25°C ON state ( all channels ON ) VCC - V STAT = V IN = VGND = 24V; VOUT = 0V IOUTleak OFF state output leakage current VIN = VGND = 0V; VCC = VOUT = 24V; Tamb = 25°C IOUTleak OFF state output leakage current VIN = VGND = 0V; VCC = 24V; Table 4. Symbol 70 5 0 VOUT = 10V; Tamb = 25°C Switching ( VCC = 24V) Parameter Test Conditions t(ON) Turn-on delay time of Output current RL = 96 from VIN rising edge to VOUT = 2.4V t(OFF) Turn-off delay time of Output current RL = 96 from VIN rising edge to Min. VOUT = 21.6V Typ. 10 µs 40 µs (dVOUT/dt)on Turn-on voltage slope RL = 96 from VOUT = 2.4V to 19.2V 0.75 V/µs (dVOUT/dt)off Turn-off voltage slope RL = 96 from VOUT = 21.6V to 2.4V 0.25 V/µs Table 5. Symbol Ilim Parameter Test Conditions Current limitation Min. Typ. Max. Unit 0.35 0.7 1.1 A T(hyst) Thermal hysteresis 7 15 TTSD Thermal shut-down temperature 150 175 TR Reset temperature 135 Vdemag 4/15 Protections ( Per channel ) Turn-off output clamp voltage IOUT = 0.25A, VCC = 24V °C 200 VCC-59 VCC-52 VCC-47 °C °C V VNQ860-E / VNQ860SP-E Table 6. Logical Input ( Per channel ) Symbol Parameter Test Conditions VIL Low level input voltage IIL Low level input current VIH High level input voltage . IIH High level input current. VI(HYST) Input hysteresis voltage IIN VOL Table 7. Min. Typ. Max. 1.25 VIN = 1.25V µΑ 3.25 V 10 0.5 Input current I/O Output votage IIN = 5mA ( Fault condition ) V 1 VIN = 3.25V VIN = VCC = 36V Unit µΑ V 200 µΑ 1 V Max. Unit Status Pin Symbol Parameter Test Conditions Min. Typ. VSTAT Status low output voltage ISTAT = 5mA ( Fault condition ) 1 V ILSTAT Status leakage current Normal operation; VSTAT = V CC = 36V 10 µΑ CSTAT Status pin input capacitance Normal operation; VSTAT = 5V 100 pF Max. Unit 1 V Table 8. VCC - Output Diode Symbol Parameter VF Forwardon Voltage Table 9. Truth Table Test Conditions Min. -IOUT = 0.3A; T J = 150°C Typ. Conditions MCOUTn I/On OUTPUTn STATUS Normal operation L H L H L H H H Current limitation L H L H L X H H Overtemperature L H L Driven low L L X X Undervoltage L H L H L L X X Overvoltage L H L H L L H H 5/15 VNQ860-E / VNQ860SP-E Figure 3. Switching Characteristics Figure 4. Typical Application Schematic 6/15 VNQ860-E / VNQ860SP-E Figure 5. Waveforms 7/15 VNQ860-E / VNQ860SP-E PowerSO-10TM Thermal Data Figure 6. PowerSO-10TM PC Board Figure 7. RthJA Vs. PBC copper area in open box free air condition 8/15 VNQ860-E / VNQ860SP-E Mechanical Data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 9/15 VNQ860-E / VNQ860SP-E Table 10. PowerSO-10TM Mechanical Data Figure 8. PowerSO-10TM Package Dimensions 10/15 VNQ860-E / VNQ860SP-E Figure 9. PowerSO-10TM Suggested Pad and Tube Shipment (No Suffix) Figure 10. Tape and Reel Shipment (Suffix “TR“) 11/15 VNQ860-E / VNQ860SP-E Table 11. 12/15 SO-20 Mechanical Data VNQ860-E / VNQ860SP-E Figure 11. SO-20 Tube Shipment ( no suffix ) Figure 12. Tape and Reel Shipment ( suffix “13TR“) 13/15 VNQ860-E / VNQ860SP-E Table 12. Revision History Date Revision 14-Jul-2005 1 Updates , New template. 7-Nov-2005 2 Few Updates. 14/15 Description of Change VNQ860-E / VNQ860SP-E Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners © 2005 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 15/15