OPA690 OPA 690 OPA6 90 SBOS223A—DECEMBER 2001 – REVISED JULY 2002 Wideband, Voltage Feedback OPERATIONAL AMPLIFIER With Disable FEATURES APPLICATIONS ● FLEXIBLE SUPPLY RANGE: +5V to +12V Single Supply ±2.5V to ±5V Dual Supply ● UNITY-GAIN STABLE: 500MHz (G = 1) ● HIGH OUTPUT CURRENT: 190mA ● OUTPUT VOLTAGE SWING: ±4.0V ● HIGH SLEW RATE: 1800V/µs ● LOW SUPPLY CURRENT: 5.5mA ● LOW DISABLED CURRENT: 100µA ● WIDEBAND +5V OPERATION: 220MHz (G = 2) ● ● ● ● ● ● ● ● DESCRIPTION The OPA690’s low 5.5mA supply current is precisely trimmed at 25°C. This trim, along with low temperature drift, gives lower maximum supply current than competing products. System power may be reduced further using the optional disable control pin. Leaving this disable pin open, or holding it HIGH, will operate the OPA690 normally. If pulled LOW, the OPA690 supply current drops to less than 100µA while the output goes to a high impedance state. This feature may be used for power savings. The OPA690 represents a major step forward in unity-gain stable, voltage feedback op amps. A new internal architecture provides slew rate and full-power bandwidth previously found only in wideband current feedback op amps. A new output stage architecture delivers high currents with a minimal headroom requirement. These combine to give exceptional single-supply operation. Using a single +5V supply, the OPA690 can deliver a 1V to 4V output swing with over 150mA drive current and 150MHz bandwidth. This combination of features makes the OPA690 an ideal RGB line driver or single-supply Analog-to-Digital Converter (ADC) input driver. OPA690 RELATED PRODUCTS R1 VI R2 DUALS TRIPLES OPA680 OPA2690 OPA3690 Current Feedback OPA691 OPA2691 OPA3691 Fixed Gain OPA692 OPA2682 OPA3692 3.3V 2.5V 0.1µF C1 SINGLES Voltage Feedback +5V R1 VIDEO LINE DRIVER xDSL LINE DRIVER/RECEIVER HIGH SPEED IMAGING CHANNELS ADC BUFFERS PORTABLE INSTRUMENTS TRANSIMPEDANCE AMPLIFIERS ACTIVE FILTERS OPA680 UPGRADE 3 2 8 C2 R4 20Ω OPA690 4 R3 R5 20Ω THS1040 C3 20pF C6 20pF C4 10µF AIN+ 10-Bit 40MSPS AIN– VREF = 1V C5 0.1µF Single-Supply ADC Driver Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2001, Texas Instruments Incorporated www.ti.com ELECTROSTATIC DISCHARGE SENSITIVITY ABSOLUTE MAXIMUM RATINGS(1) Power Supply ............................................................................... ±6.5VDC Internal Power Dissipation .................................... See Thermal Analysis Differential Input Voltage .................................................................. ±1.2V Input Voltage Range ........................................................................... ±VS Storage Temperature Range: D, DBV ........................... –40°C to +125°C Lead Temperature (soldering, 10s) .............................................. +300°C Junction Temperature (TJ ) ........................................................... +175°C ESD Resistance: HBM .................................................................... 2000V MM ........................................................................ 200V CDM .................................................................... 1500V This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. NOTE: (1) Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliability. PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR(1) OPA690ID SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER TRANSPORT MEDIA, QUANTITY OPA690ID OPA690IDR Rails, 100 Tape and Reel, 2500 OPA690IDBVT OPA690IDBVR Tape and Reel, 250 Tape and Reel, 3000 SO-8 D –40°C to +85°C OPA690 " " " " " OPA690IDBV SOT23-6 DBV –40°C to +85°C OAEI " " " " " NOTE: (1) For the most current specifications and package information, refer to our web site at www.ti.com. PIN CONFIGURATIONS 1 8 DIS Inverting Input 2 7 +VS Noninverting Input 3 6 Output –VS 4 5 NC SOT23 Output 1 6 +VS –VS 2 5 DIS Noninverting Input 3 4 Inverting Input 6 NC Top View 4 SO 5 Top View 3 2 1 OAEI Pin Orientation/Package Marking 2 OPA690 www.ti.com SBOS223A ELECTRICAL CHARACTERISTICS: VS = ±5V Boldface limits are tested at +25°C. RF = 402Ω, RL = 100Ω, and G = +2, (see Figure 1 for AC performance only), unless otherwise noted. OPA690ID, IDBV TYP PARAMETER AC PERFORMANCE (see Figure 1) Small-Signal Bandwidth Gain-Bandwidth Product Bandwidth for 0.1dB Gain Flatness Peaking at a Gain of +1 Large-Signal Bandwidth Slew Rate Rise-and-Fall Time Settling Time to 0.02% 0.1% Harmonic Distortion 2nd-Harmonic 3rd-Harmonic Input Voltage Noise Input Current Noise Differential Gain Differential Phase DC PERFORMANCE(4) Open-Loop Voltage Gain (AOL) Input Offset Voltage Average Offset Voltage Drift Input Bias Current Average Bias Current Drift (magnitude) Input Offset Current Average Offset Current Drift INPUT Common-Mode Input Range (CMIR)(5) Common-Mode Rejection Ratio (CMRR) Input Impedance Differential-Mode Common-Mode OUTPUT Voltage Output Swing Current Output, Sourcing Current Output, Sinking Short-Circuit Current Limit Closed-Loop Output Impedance DISABLE (Disabled LOW) Power-Down Supply Current (+VS) Disable Time Enable Time Off Isolation Output Capacitance in Disable Turn On Glitch Turn Off Glitch Enable Voltage Disable Voltage Control Pin Input Bias Current (VDIS) POWER SUPPLY Specified Operating Voltage Maximum Operating Voltage Range Max Quiescent Current Min Quiescent Current Power-Supply Rejection Ratio (+PSRR) THERMAL CHARACTERISTICS Specified Operating Range D, DBV Package Thermal Resistance, θJA D SO-8 DBV SOT23-6 CONDITIONS +25°C G = +1, VO = 0.5Vp-p, RF = 25Ω G = +2, VO = 0.5Vp-p G = +10, VO = 0.5Vp-p G ≥ 10 G = +2, VO < 0.5Vp-p VO < 0.5Vp-p G = +2, VO = 5Vp-p G = +2, 4V Step G = +2, VO = 0.5V Step G = +2, VO = 5V Step G = +2, VO = 2V Step G = +2, VO = 2V Step 500 220 30 300 30 4 200 1800 1.4 2.8 12 8 G = +2, f = 5MHz, VO = 2Vp-p RL = 100Ω RL ≥ 500Ω RL = 100Ω RL ≥ 500Ω f > 1MHz f > 1MHz G = +2, NTSC, VO = 1.4Vp, RL = 150 G = +2, NTSC, VO = 1.4Vp, RL = 150 –68 –77 –70 –81 5.5 3.1 0.06 0.03 VO = 0V, RL = 100Ω VCM = 0V VCM = 0V VCM = 0V VCM = 0V VCM = 0V VCM = 0V MIN /MAX OVER TEMPERATURE +25°C(1) 0°C to 70°C(2) –40°C to +85°C(2) 165 20 200 160 19 190 150 18 180 1400 1200 900 –64 –70 –68 –78 –62 –68 –66 –76 58 69 ±1.0 ±4 +3 ±8 ±0.1 ±1.0 VCM = ±1V ±3.5 65 ±3.4 VCM = 0 VCM = 0 190 || 0.6 3.2 || 0.9 No Load 100Ω Load VO = 0 VO = 0 VO = 0 G = +2, f = 100kHz ±4.0 ±3.9 +190 –190 ±250 0.04 VDIS = 0 VIN = 1VDC VIN = 1VDC G = +2, 5MHz –100 200 25 70 4 ±50 ±20 3.3 1.8 75 G = +2, RL = 150Ω, VIN = 0 G = +2, RL = 150Ω, VIN = 0 VDIS = 0 ±3.8 ±3.7 MIN/ TEST MAX LEVEL(3) MHz MHz MHz MHz MHz dB MHz V/µs ns ns ns ns typ typ typ typ typ typ typ typ typ typ typ typ C C C C C C C C C C C C –60 –66 –64 –75 dBc dBc dBc dBc nV/√Hz pA/√Hz % deg typ typ typ typ typ typ typ typ C C C C C C C C 56 ±4.5 ±10 ±9 ±20 ±1.4 ±7 54 ±4.7 ±10 ±11 ±40 ±1.6 ±9 dB mV µV/°C µA nA/°C µA nA/°C min max max max max max max A A B A B A B ±3.3 57 ±3.2 56 V dB min min A A kΩ || pF MΩ || pF typ typ C C +160 –160 ±3.7 ±3.6 +140 –140 ±3.6 ±3.3 +100 –100 V V mA mA mA Ω min min min min typ typ A A A A C C –200 –240 –260 3.5 1.7 130 3.6 1.6 150 3.7 1.5 160 µA ns ns dB pF mV mV V V µA max typ typ typ typ typ typ min max max A C C C C C C A A A ±6.0 ±6 6.0 5.1 66 ±6 6.2 4.7 64 V V mA mA dB typ max max min min C A A A A –40 to +85 °C typ C 125 150 °C/W °C/W typ typ C C ±5 VS = ±5V VS = ±5V Input Referred 60 UNITS 5.5 5.5 75 5.8 5.3 68 Junction-to-Ambient NOTES: (1) Junction Temperature = Ambient for 25°C specifications. (2) Junction Temperature = Ambient at low temperature limit: Junction Temperature = Ambient +10°C at high temperature limit for over temperature specifications. (3) Test Levels: (A) 100% tested at 25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and simulation. (C) Typical value only for information. (4) Current is considered positive out of node. VCM is the input common-mode voltage. (5) Tested < 3dB below minimum CMRR specification at ±CMIR limits. OPA690 SBOS223A www.ti.com 3 ELECTRICAL CHARACTERISTICS: VS = +5V Boldface limits are tested at +25°C. RF = 402Ω, RL = 100Ω, and G = +2, (see Figure 2 for AC performance only), unless otherwise noted. OPA690ID, IDBV TYP PARAMETER AC PERFORMANCE (see Figure 2) Small-Signal Bandwidth Gain-Bandwidth Product Bandwidth for 0.1dB Gain Flatness Peaking at a Gain of +1 Large-Signal Bandwidth Slew Rate Rise-and-Fall Time Settling Time to 0.02% 0.1% Harmonic Distortion 2nd-Harmonic 3rd-Harmonic Input Voltage Noise Input Current Noise Differential Gain Differential Phase DC PERFORMANCE(4) Open-Loop Voltage Gain (AOL ) Input Offset Voltage Average Offset Voltage Drift Input Bias Current Average Bias Current Drift (magnitude) Input Offset Current Average Offset Current Drift INPUT Least Positive Input Voltage(5) Most Positive Input Voltage(5) Common-Mode Rejection Ratio (CMRR) Input Impedance Differential-Mode Common-Mode OUTPUT Most Positive Output Voltage Least Positive Output Voltage Current Output, Sourcing Current Output, Sinking Short-Circuit Current Closed-Loop Output Impedance DISABLE (Disable LOW) Power-Down Supply Current (+VS) Off Isolation Output Capacitance in Disable Turn On Glitch Turn Off Glitch Enable Voltage Disable Voltage Control Pin Input Bias Current (VDIS) POWER SUPPLY Specified Single-Supply Operating Voltage Maximum Single-Supply Operating Voltage Max Quiescent Current Min Quiescent Current Power-Supply Rejection Ratio (+PSRR) TEMPERATURE RANGE Specification: D, DBV Thermal Resistance, θJA D SO-8 DBV SOT23-6 MIN/MAX OVER TEMPERATURE +25°C(1) 0°C to 70°C(2) –40°C to +85°C(2) 150 18 180 145 17 170 140 16 160 700 670 550 –60 –70 –64 –73 –59 –68 –62 –71 56 CONDITIONS +25°C G = +1, VO < 0.5Vp-p, RF = ±25Ω G = +2, VO < 0.5Vp-p G = +10, VO < 0.5Vp-p G ≥ 10 G = +2, VO < 0.5Vp-p VO < 0.5Vp-p G = +2, VO = 2Vp-p G = +2, 2V Step G = +2, VO = 0.5V Step G = +2, VO = 2V Step G = +2, VO = 2V Step G = +2, VO = 2V Step G = +2, f = 5MHz, VO = 2Vp-p RL = 100Ω to VS /2 RL ≥ 500Ω to VS /2 RL = 100Ω to VS /2 RL ≥ 500Ω to VS /2 f > 1MHz f > 1MHz G = +2, NTSC, VO = 1.4Vp, RL = 150 to VS / 2 G = +2, NTSC, VO = 1.4Vp, RL = 150 to VS / 2 400 190 25 250 20 5 220 1000 1.6 2.0 12 8 VO = 2.5V, RL = 100Ω to 2.5V VCM = 2.5V VCM = 2.5V VCM = 2.5V VCM = 2.5V VCM = 2.5V VCM = 2.5V 63 ±1.0 ±4 +3 ±8 ±0.3 ±1 VCM = 2.5V ±0.5V 1.5 3.5 63 1.6 3.4 58 VCM = 2.5V VCM = 2.5V 92 || 1.4 2.2 || 1.5 No Load RL = 100Ω to 2.5V No Load RL = 100Ω to 2.5V 4 3.9 1 1.1 +160 –160 ±250 0.04 3.8 3.7 1.2 1.3 +120 –120 3.6 3.5 1.4 1.5 +100 –100 –100 65 4 ±50 ±20 3.3 1.8 75 –200 G = +2, f = 100kHz VDIS = 0 G = +2, 5MHz G = +2, RL = 150Ω, VIN = VS /2 G = +2, RL = 150Ω, VIN = VS / 2 VDIS = 0 MIN/ TEST MAX LEVEL(3) MHz MHz MHz MHz MHz dB MHz V/µs ns ns ns ns typ typ typ typ typ typ typ typ typ typ typ typ C C C C C C C C C C C C –56 –66 –60 –70 dBc dBc dBc dBc nV/√Hz pA/√Hz % deg typ typ typ typ typ typ typ typ C C C C C C C C 54 ±4.3 ±10 ±9 ±20 ±1.4 ±7 52 ±4.7 ±10 ±11 ±40 ±1.6 ±9 dB mV µV/°C µA nA/°C µA nA/°C min max max max max max max A A B A B A B 1.7 3.3 56 1.8 3.2 54 V V dB max min min A A A kΩ || pF MΩ || pF typ typ C C 3.5 3.4 1.5 1.7 +80 –80 V V V V mA mA mA Ω min min min max max min typ typ A A A A A A C C –240 –260 3.5 1.7 130 3.6 1.6 150 3.7 1.5 160 µA dB pF mV mV V V µA max typ typ typ typ min max typ A C C C C A A C 12 5.2 4.7 12 5.4 4.4 12 5.6 4.0 V V mA mA dB typ max max min typ C B A A C –40 to +85 °C typ C 125 150 °C/W °C/W typ typ C C –65 –75 –68 –77 5.6 3.2 0.06 0.02 5 VS = +5V VS = +5V Input Referred UNITS 4.9 4.9 72 Junction-to-Ambient NOTES: (1) Junction Temperature = Ambient for 25°C tested specifications. (2) Junction Temperature = Ambient at low temperature limit: Junction Temperature = Ambient +10°C at high temperature limit for over temperature tested specifications. (3) Test Levels: (A) 100% tested at 25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and simulation. (C) Typical value only for information. (4) Current is considered positive out of node. VCM is the input common-mode voltage. (5) Tested < 3dB below minimum CMRR specification at ±CMIR limits. 4 OPA690 www.ti.com SBOS223A TYPICAL CHARACTERISTICS: VS = ±5V At TA = +25°C, G = +2, RF = 402Ω, and RL = 100Ω, (see Figure 1 for AC performance only), unless otherwise noted. LARGE-SIGNAL FREQUENCY RESPONSE SMALL-SIGNAL FREQUENCY RESPONSE 6 VO = 0.5Vp-p G = +1 RF = 25Ω 3 6 0 G=2 G=5 –3 Gain (3dB/div) Normalized Gain (3dB/div) 9 –6 G = 10 VO = 2Vp-p 3 VO = 1Vp-p 0 VO = 4Vp-p –9 –3 –12 VO = 7Vp-p –15 0.7 10 –6 0.5 700 100 1 10 Frequency (MHz) Frequency (MHz) SMALL-SIGNAL PULSE RESPONSE +4 G = +2 VO = 0.5Vp-p G = +2 VO = 5Vp-p +3 Output Voltage (1V/div) 300 Output Voltage (100mV/div) 500 LARGE-SIGNAL PULSE RESPONSE 400 200 100 0 –100 –200 –300 +2 +1 0 –1 –2 –3 –400 –4 Time (5ns/div) Time (5ns/div) COMPOSITE VIDEO dG/dP 0.2 +5V –50 0.15 402Ω Optional 1.3kΩ Pull-Down dG 402Ω 0.125 dG 0.1 VDIS = 0 –55 OPA690 Feedthrough (5dB/div) 75Ω DISABLE FEEDTHROUGH vs FREQUENCY –45 No Pull-Down With 1.3kΩ Pull-Down Video In 0.175 dG/dP (%/degree) 100 –5V dP 0.075 0.05 dP –60 –65 –70 –75 –80 –85 –90 0.025 Reverse –95 –100 100k 0 1 2 3 4 1M 10M 100M Frequency (Hz) Number of 150Ω Loads OPA690 SBOS223A Forward www.ti.com 5 TYPICAL CHARACTERISTICS: VS = ±5V (Cont.) At TA = +25°C, G = +2, RF = 402Ω, and RL = 100Ω, (see Figure 1 for AC performance only), unless otherwise noted. 5MHz HARMONIC DISTORTION vs SUPPLY VOLTAGE HARMONIC DISTORTION vs LOAD RESISTANCE –60 VO = 2Vp-p RL = 100Ω f = 5MHz VO = 2Vp-p f = 5MHz –65 Harmonic Distortion (dBc) Harmonic Distortion (dBc) –60 –70 2nd-Harmonic –75 3rd-Harmonic –80 –85 –65 2nd-Harmonic –70 3rd-Harmonic –75 –80 –90 1000 100 2 2.5 3 3.5 HARMONIC DISTORTION vs FREQUENCY –60 2nd-Harmonic –70 –80 3rd-Harmonic –90 6 2nd-Harmonic –65 –70 3rd-Harmonic –75 –80 0.1 1 10 20 0.1 5 1 Frequency (MHz) Output Voltage Swing (Vp-p) HARMONIC DISTORTION vs NONINVERTING GAIN HARMONIC DISTORTION vs INVERTING GAIN –40 –40 VO = 2Vp-p RL = 100Ω f = 5MHz Figure1 –50 Harmonic Distortion (dBc) Harmonic Distortion (dBc) 5.5 RL = 100Ω f = 5MHz –100 –60 2nd-Harmonic 3rd-Harmonic –70 –80 VO = 2Vp-p RL = 100Ω f = 5MHz RF = 1kΩ –50 –60 2nd-Harmonic 3rd-Harmonic –70 –80 –90 1 10 20 1 Gain (V/V) 6 5 HARMONIC DISTORTION vs OUTPUT VOLTAGE VO = 2Vp-p RL = 100Ω –50 4.5 –60 Harmonic Distortion (dBc) Harmonic Distortion (dBc) –40 4 Supply Voltage (±VS) Load Resistance (Ω) 10 20 Inverting Gain (V/V) OPA690 www.ti.com SBOS223A TYPICAL CHARACTERISTICS: VS = ±5V (Cont.) At TA = +25°C, G = +2, RF = 402Ω, and RL = 100Ω, (see Figure 1 for AC performance only), unless otherwise noted. 2-TONE, 3RD-ORDER INTERMODULATION SPURIOUS INPUT VOLTAGE AND CURRENT NOISE DENSITY –30 3rd-Order Spurious Level (dBc) Voltage Noise (nV/√Hz) Current Noise (pA/√Hz) 100 10 Voltage Noise 5.5nV/√Hz Current Noise 3.1pA/√Hz –35 50MHz –40 –45 –50 20MHz –55 –60 –65 10MHz Load Power at Matched 50Ω Load, see Figure 1 –70 –75 1 100 1k 10k 100k –8 10M 1M –6 –4 –2 0 2 4 Frequency (Hz) 8 10 FREQUENCY RESPONSE vs CAPACITIVE LOAD RECOMMENDED RS vs CAPACITIVE LOAD 9 80 G = +2 Gain-to-Capacitive Load (dB) 70 60 50 RS (Ω) 6 Single-Tone Load Power (dBm) 40 30 20 10 CL = 10pF 6 CL = 100pF 3 CL = 22pF 0 CL = 47pF –3 VIN RS VOUT OPA690 1kΩ CL 402Ω –6 402Ω 1kΩ is optional. –9 0 0 1000 100 LARGE-SIGNAL DISABLE/ENABLE RESPONSE Output Voltage Each Channel SO-14 Package Only 0.8 0.4 0 G = +2 VIN = +1V 100 120 140 160 180 200 4 2 0 Time (50ns/div) 30 20 10 0 –10 Output Voltage Vi = 0V –20 –30 Time (20ns/div) OPA690 SBOS223A 80 VDIS Output Voltage (10mV/div) Output Voltage (0.4V/div) 2 0 1.2 60 6 VDIS (2V/div) 4 VDIS 1.6 40 DISABLE/ENABLE GLITCH 6 2.0 20 Frequency (20MHz/div) Capacitive Load (pF) VDIS (2V/div) 10 www.ti.com 7 TYPICAL CHARACTERISTICS: VS = ±5V (Cont.) At TA = +25°C, G = +2, RF = 402Ω, and RL = 100Ω, (see Figure 1 for AC performance only), unless otherwise noted. OUTPUT VOLTAGE AND CURRENT LIMITATIONS 1W Internal Power Limit 1.5 Input Offset Voltage (mV) 3 2 VO (V) 1 0 25Ω Load Line 50Ω Load Line –1 –2 100Ω Load Line –3 –4 –200 Input Bias Current (IB) 1 0.5 Input Offset Current (IOS) 0 0 –0.5 –10 –1 Input Offset Voltage (VOS) –20 –2 –100 0 100 200 300 –50 –25 IO (mA) 0 25 50 75 100 125 Ambient Temperature (°C) COMMON-MODE REJECTION RATIO AND POWER-SUPPLY REJECTION RATIO vs FREQUENCY SUPPLY AND OUTPUT CURRENT vs TEMPERATURE 100 8 250 Sourcing Output Current –PSRR 90 80 Supply Current (2mA/div) Power-Supply Rejection Ratio (dB) Common-Mode Rejection Ratio (dB) 10 –1.5 1W Internal Power Limit Output Current Limit –5 –300 20 CMRR 70 60 +PSRR 50 40 30 20 7 200 Sinking Output Current 6 150 5 100 Quiescent Supply Current 4 50 Output Current (50mA/div) 4 TYPICAL DC DRIFT OVER TEMPERATURE 2 Output Current Limited Input Bias and Offset Currents (µA) 5 10 0 3 10k 100k 1M 10M 100M –50 –25 Frequency (MHz) 25 50 75 100 0 125 Ambient Temperature (°C) CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY 10 0 OPEN-LOOP GAIN AND PHASE 70 +5V 0 60 –30 ZO 1 –5V 402Ω 402Ω 0.1 0.01 –60 Open-Loop Phase 40 –90 30 –120 20 –150 10 –180 0 –210 –10 –240 –20 10k 100k 1M 10M 100M Frequency (Hz) 8 50 1k 10k 100k 1M 10M 100M –270 1G Frequency (Hz) OPA690 www.ti.com SBOS223A Open-Loop Phase (°) 200Ω Open-Loop Gain (dB) Output Impedance (Ω) Open-Loop Gain OPA690 TYPICAL CHARACTERISTICS: VS = +5V At TA = +25°C, G = +2, RF = 402Ω, and RL = 100Ω, (see Figure 2 for AC performance only), unless otherwise noted. SMALL-SIGNAL FREQUENCY RESPONSE LARGE-SIGNAL FREQUENCY RESPONSE 6 9 VO = 2Vp-p G = +1 RF = 25Ω 3 6 G = +2 Gain (3dB/div) Normalized Gain (1dB/div) VO = 0.5Vp-p 0 G = +5 –3 VO = 3Vp-p 3 VO = 1Vp-p 0 G = +10 –6 –3 –9 –6 0.7 1 100 10 700 0.5 1 SMALL-SIGNAL PULSE RESPONSE LARGE-SIGNAL PULSE RESPONSE 4.1 Output Voltage (400mV/div) G = +2 VO = 0.5Vp-p 2.8 2.7 2.6 2.5 2.4 2.3 2.2 G = +2 VO = 2Vp-p 3.7 3.3 2.9 2.5 2.1 1.7 1.3 2.1 0.9 Time (5ns/div) Time (5ns/div) RECOMMENDED RS vs CAPACITIVE LOAD FREQUENCY RESPONSE vs CAPACITIVE LOAD 50 9 CL = 10pF Gain-to-Capacitive Load (dB) 45 40 35 RS (Ω) 500 Frequency (MHz) 2.9 Output Voltage (100mV/div) 100 10 Frequency (Hz) 30 25 20 15 10 6 CL = 100pF 3 0 CL = 22pF +5V –3 0.1µF 714Ω VIN RS 58Ω 714Ω 714Ω OPA690 VOUT CL –6 CL = 47pF 402Ω +5V 5 402Ω 0 –9 1 10 100 1000 Capacitive Load (pF) 20 40 60 80 100 120 140 160 180 200 Frequency (20MHz/div) OPA690 SBOS223A 0 www.ti.com 9 TYPICAL CHARACTERISTICS: VS = +5V (Cont.) At TA = +25°C, G = +2, RF = 402Ω, and RL = 100Ω, (see Figure 2 for AC performance only), unless otherwise noted. HARMONIC DISTORTION vs LOAD RESISTANCE HARMONIC DISTORTION vs FREQUENCY –60 –40 Harmonic Distortion (dBc) Harmonic Distortion (dBc) VO = 2Vp-p f = 5MHz –65 –70 2nd-Harmonic 3rd-Harmonic –75 –80 2nd-Harmonic –70 –80 3rd-Harmonic –90 –100 0.1 1 10 Resistance (Ω) Frequency (MHz) HARMONIC DISTORTION vs OUTPUT VOLTAGE 2-TONE, 3RD-ORDER INTERMODULATION SPURIOUS –60 20 –30 –65 3rd-Order Spurious Level (dBc) RL = 100Ω to 2.5V f = 5MHz Harmonic Distortion (dBc) –60 1000 100 3rd-Harmonic –70 2nd-Harmonic –75 –80 –35 –40 50MHz –45 –50 20MHz –55 –60 –65 10MHz –70 Load Power at Matched 50Ω Load, see Figure 2 –75 0.1 1 3 –14 Output Voltage Swing (Vp-p) 10 –50 VO = 2Vp-p RL = 100Ω to 2.5V –12 –10 –8 –6 –4 –2 0 2 Single-Tone Load Power (dBm) OPA690 www.ti.com SBOS223A APPLICATIONS INFORMATION WIDEBAND VOLTAGE FEEDBACK OPERATION The OPA690 provides an exceptional combination of high output power capability with a wideband, unity-gain stable voltage feedback op amp using a new high slew rate input stage. Typical differential input stages used for voltage feedback op amps are designed to steer a fixed-bias current to the compensation capacitor, setting a limit to the achievable slew rate. The OPA690 uses a new input stage which places the transconductance element between two input buffers, using their output currents as the forward signal. As the error voltage increases across the two inputs, an increasing current is delivered to the compensation capacitor. This provides very high slew rate (1800V/µs) while consuming relatively low quiescent current (5.5mA). This exceptional full-power performance comes at the price of a slightly higher input noise voltage than alternative architectures. The 5.5nV/√Hzinput voltage noise for the OPA690 is exceptionally low for this type of input stage. Figure 1 shows the DC-coupled, gain of +2, dual powersupply circuit configuration used as the basis of the ±5V Electrical Characteristics and Typical Characteristics. For test purposes, the input impedance is set to 50Ω with a resistor to ground and the output impedance is set to 50Ω with a series output resistor. Voltage swings reported in the specifications are taken directly at the input and output pins, while output powers (dBm) are at the matched 50Ω load. For the circuit of Figure 1, the total effective load will be 100Ω || 804Ω. The disable control line is typically left open to ensure normal amplifier operation. Two optional components are included in Figure 1. An additional resistor (175Ω) is included in series with the noninverting input. Combined with the 25Ω DC source resistance looking back towards the signal generator, this gives an input bias current cancelling resistance that matches the 200Ω source resistance seen at the inverting input (see the DC Accuracy and Offset Control section). In addition to the usual power-supply decoupling capacitors to ground, a 0.1µF capacitor is included between the two powersupply pins. In practical PC board layouts, this optional-added capacitor will typically improve the 2nd-harmonic distortion performance by 3dB to 6dB. Figure 2 shows the AC-coupled, gain of +2, single-supply circuit configuration which is the basis of the +5V Specifications and Typical Characteristics. Though not a “rail-to-rail” design, the OPA690 requires minimal input and output voltage headroom compared to other very wideband voltage feedback op amps. It will deliver a 3Vp-p output swing on a single +5V supply with > 150MHz bandwidth. The key requirement of broadband single-supply operation is to maintain input and output signal swings within the useable voltage ranges at both the input and the output. The circuit of Figure 2 establishes an input midpoint bias using a simple resistive divider from the +5V supply (two 698Ω resistors). The input signal is then AC-coupled into the midpoint voltage bias. The input voltage can swing to within 1.5V of either supply pin, giving a 2Vp-p input signal range centered between the supply pins. The input impedance matching resistor (59Ω) used for testing is adjusted to give a 50Ω input load when the parallel combination of the biasing divider network is included. Again, an additional resistor (50Ω in this case) is included directly in series with the noninverting input. This minimum recommended value provides part of the DC source resistance matching for the noninverting input bias current. It is also used to form a simple parasitic pole to roll off the frequency response at very high frequencies (> 500MHz) using the input parasitic capacitance to form a bandlimiting pole. The gain resistor (RG) is AC-coupled, giving the circuit a DC gain of +1, which puts the input DC bias voltage (2.5V) at the output as well. The output voltage can swing to within +5V 0.1µF +5V +VS 6.8µF + + 0.1µF 50Ω Source VI 50Ω Source 175Ω 50Ω 6.8µF 698Ω DIS VO 50Ω 0.1µF 50Ω Load OPA690 0.1µF VI 59Ω 50Ω 698Ω DIS VO OPA690 100Ω VS/2 RF 402Ω RF 402Ω RG 402Ω RG 402Ω + 6.8µF 0.1µF 0.1µF –5V FIGURE 1. DC-Coupled, G = +2, Bipolar Supply, Specification and Test Circuit. FIGURE 2. AC-Coupled, G = +2, Single-Supply, Specification and Test Circuit. OPA690 SBOS223A www.ti.com 11 1V of either supply pin while delivering > 100mA output current. A demanding 100Ω load to a midpoint bias is used in this characterization circuit. The new output stage circuit used in the OPA690 can deliver large bipolar output currents into this midpoint load with minimal crossover distortion, as shown in the +5V supply, 3rd-harmonic distortion plots. 70 VO = 2Vp-p, 10MHz 68 66 SFDR (dBc) 64 SINGLE-SUPPLY ADC INTERFACE 62 60 58 56 Most modern, high performance ADC (such as the TI ADS8xx and ADS9xx series) operate on a single +5V (or lower) power supply. It has been a considerable challenge for single-supply op amps to deliver a low distortion input signal at the ADC input for signal frequencies exceeding 5MHz. The high slew rate, exceptional output swing, and high linearity of the OPA690 make it an ideal single-supply ADC driver. The circuit on the front page shows one possible (inverting) interface. Figure 3 shows the test circuit of Figure 2 modified for a capacitive (ADC) load and with an optional output pull-down resistor (RB). 54 52 50 0 1 2 3 4 5 6 7 8 9 10 Output Pull-Down Current (mA) FIGURE 4. SFDR versus IB. HIGH-PERFORMANCE DAC TRANSIMPEDANCE AMPLIFIER The OPA690 in the circuit of Figure 3 provides > 200MHz bandwidth for a 2Vp-p output swing. Minimal 3rd-harmonic distortion or 2-tone, 3rd-order intermodulation distortion will be observed due to the very low crossover distortion in the OPA690 output stage. The limit of output Spurious-Free Dynamic Range (SFDR) will be set by the 2nd-harmonic distortion. Without RB, the circuit of Figure 3 measured at 10MHz shows an SFDR of 57dBc. This may be improved by pulling additional DC bias current (IB) out of the output stage through the optional RB resistor to ground (the output midpoint is at 2.5V for Figure 3). Adjusting IB gives the improvement in SFDR shown in Figure 4. SFDR improvement is achieved for IB values up to 5mA, with worse performance for higher values. High-frequency DDS Digital-to-Analog Converters (DACs) require a low distortion output amplifier to retain their SFDR performance into real-world loads. See Figure 5 for a single-ended output drive implementation. In this circuit, only one side of the complementary output drive signal is used. The diagram shows the signal output current connected into the virtual ground summing junction of the OPA690, which is set up as a transimpedance stage or “I-V converter”. The unused current output of the DAC is connected to ground. If the DAC requires its outputs terminated to a compliance voltage other than ground for operation, the appropriate voltage level may be applied to the noninverting input of the OPA690. The +5V Power-Supply Decoupling Not Shown 698Ω DIS 0.1µF 50Ω RS 30Ω VI 1Vp-p 2.5V DC ±1V AC OPA690 59Ω 698Ω 50pF ADC Input 402Ω 402Ω 0.1µF RB IB FIGURE 3. Single-Supply ADC Input Driver. 12 OPA690 www.ti.com SBOS223A 50Ω OPA690 High-Speed DAC VO = IO RF +12V RF 2kΩ 8Vp-p CF CD IO 50Ω 4Vp-p OPA690 0.1µF 2kΩ 50Ω Load GBP → Gain Bandwidth Product (Hz) for the OPA690 50Ω 1Vp-p IO 400Ω 5pF 50Ω Source FIGURE 5. DAC Transimpedance Amplifier. FIGURE 6. High Power Coax Line Driver. DC gain for this circuit is equal to RF. At high frequencies, the DAC output capacitance will produce a zero in the noise gain for the OPA690 that may cause peaking in the closedloop frequency response. CF is added across RF to compensate for this noise gain peaking. To achieve a flat transimpedance frequency response, the pole in the feedback network should be set to: of the amplifier using a single 12V supply. Figure 6 shows such a circuit set for a gain of 8 to the output or 4 to the load. 1/ 2πRF CF = GBP / 4 πRF CD which will give a closed-loop transimpedance bandwidth f–3dB, of approximately: f–3dB = GBP / 2πRF CD HIGH POWER LINE DRIVER The large output swing capability of the OPA690 and its high current capability allows it to drive a 50Ω line with a peak-topeak signal up to 4Vp-p at the load, or 8Vp-p at the output The 5pF capacitor in the feedback loop provides added bandwidth control for the signal path. SINGLE-SUPPLY ACTIVE FILTERS The high bandwidth provided by the OPA690, while operating on a single +5V supply, lends itself well to high-frequency active filter designs. Again, the key additional requirement is to establish the DC operating point of the signal near the supply midpoint for highest dynamic range. Figure 7 shows an example design of a 5MHz low-pass Butterworth filter using the Sallen-Key topology. Both the input signal and the gain setting resistor are ACcoupled using 0.1µF blocking capacitors (actually giving bandpass response with the low-frequency pole set to 32kHz for the component values shown). As discussed for Figure 2, this allows the midpoint bias formed by the two 1.87kΩ resistors to appear at both the input and output pins. The +5V 5MHz, 2nd-Order Butterworth Filter Response 15 1.87kΩ 100pF 10 137Ω DIS 432Ω VI 4VI OPA690 1.87kΩ 150pF 5MHz, 2nd-Order Butterworth Filter Gain (dB) 0.1µF 5 0 1.5kΩ –5 100k 500Ω 1M 10M Frequency (Hz) 0.1µF FIGURE 7. Single-Supply, High-Frequency Active Filter. OPA690 SBOS223A www.ti.com 13 midband signal gain is set to +4 (12dB) in this case. The capacitor to ground on the noninverting input is intentionally set larger to dominate input parasitic terms. At a gain of +4, the OPA690 on a single supply will show ~80MHz small- and large-signal bandwidth. The resistor values have been slightly adjusted to account for this limited bandwidth in the amplifier stage. Tests of this circuit show a precise 5MHz, –3dB point with a maximally flat passband (above the 32kHz AC-coupling corner), and a maximum stopband attenuation of 36dB at the amplifier’s –3dB bandwidth of 80MHz. DESIGN-IN TOOLS DEMONSTRATION BOARDS Several PC boards are available to assist in the initial evaluation of circuit performance using the OPA690 in its three package styles. All of these are available free as an unpopulated PC board delivered with descriptive documentation. The summary information for these boards is shown below: PRODUCT OPA690ID OPA690IDBV PACKAGE BOARD PART NUMBER LITERATURE REQUEST NUMBER SO-8 SOT23-6 DEM-OPA68xU DEM-OPA6xxN SBOU009 SBOU010 The board can be requested on Texas Instruments’ web site (www.ti.com.). MACROMODELS AND APPLICATIONS SUPPORT Computer simulation of circuit performance using SPICE is often useful when analyzing the performance of analog circuits and systems. This is particularly true for Video and RF amplifier circuits where parasitic capacitance and inductance can have a major effect on circuit performance. A SPICE model for the OPA690 is available through the Texas Instruments internet web page (http://www.ti.com). These models do a good job of predicting small-signal AC and transient performance under a wide variety of operating conditions. They do not do as well in predicting the harmonic distortion or dG/dP characteristics. These models do not attempt to distinguish between the package types in their small-signal AC performance. OPERATING SUGGESTIONS OPTIMIZING RESISTOR VALUES Since the OPA690 is a unity-gain stable voltage feedback op amp, a wide range of resistor values may be used for the feedback and gain setting resistors. The primary limits on these values are set by dynamic range (noise and distortion) and parasitic capacitance considerations. For a noninverting unitygain follower application, the feedback connection should be made with a 25Ω resistor, not a direct short. This will isolate the inverting input capacitance from the output pin and improve the 14 frequency response flatness. Usually, for G > 1 application, the feedback resistor value should be between 200Ω and 1.5kΩ. Below 200Ω, the feedback network will present additional output loading which can degrade the harmonic distortion performance of the OPA690. Above 1.5kΩ, the typical parasitic capacitance (approximately 0.2pF) across the feedback resistor may cause unintentional band-limiting in the amplifier response. A good rule of thumb is to target the parallel combination of RF and RG (see Figure 1) to be less than approximately 300Ω. The combined impedance RF || RG interacts with the inverting input capacitance, placing an additional pole in the feedback network and thus, a zero in the forward response. Assuming a 2pF total parasitic on the inverting node, holding RF || RG < 300Ω will keep this pole above 250MHz. By itself, this constraint implies that the feedback resistor RF can increase to several kΩ at high gains. This is acceptable as long as the pole formed by RF and any parasitic capacitance appearing in parallel is kept out of the frequency range of interest. BANDWIDTH VERSUS GAIN: NONINVERTING OPERATION Voltage feedback op amps exhibit decreasing closed-loop bandwidth as the signal gain is increased. In theory, this relationship is described by the Gain Bandwidth Product (GBP) shown in the specifications. Ideally, dividing GBP by the noninverting signal gain (also called the Noise Gain, or NG) will predict the closed-loop bandwidth. In practice, this only holds true when the phase margin approaches 90°, as it does in high gain configurations. At low gains (increased feedback factors), most amplifiers will exhibit a more complex response with lower phase margin. The OPA690 is compensated to give a slightly peaked response in a noninverting gain of 2 (see Figure 1). This results in a typical gain of +2 bandwidth of 220MHz, far exceeding that predicted by dividing the 300MHz GBP by 2. Increasing the gain will cause the phase margin to approach 90° and the bandwidth to more closely approach the predicted value of (GBP/ NG). At a gain of +10, the 30MHz bandwidth shown in the Electrical Characteristics agrees with that predicted using the simple formula and the typical GBP of 300MHz. Frequency response in a gain of +2 may be modified to achieve exceptional flatness simply by increasing the noise gain to 2.5. One way to do this, without affecting the +2 signal gain, is to add an 804Ω resistor across the two inputs in the circuit of Figure 1. A similar technique may be used to reduce peaking in unity-gain (voltage follower) applications. For example, by using a 402Ω feedback resistor along with a 402Ω resistor across the two op amp inputs, the voltage follower response will be similar to the gain of +2 response of Figure 2. Further reducing the value of the resistor across the op amp inputs will further dampen the frequency response due to increased noise gain. The OPA690 exhibits minimal bandwidth reduction going to single-supply (+5V) operation as compared with ±5V. This is because the internal bias control circuitry retains nearly constant quiescent current as the total supply voltage between the supply pins is changed. OPA690 www.ti.com SBOS223A INVERTING AMPLIFIER OPERATION Since the OPA690 is a general-purpose, wideband voltage feedback op amp, all of the familiar op amp application circuits are available to the designer. Inverting operation is one of the more common requirements and offers several performance benefits. Figure 8 shows a typical inverting configuration where the I/O impedances and signal gain from Figure 1 are retained in an inverting circuit configuration. +5V + 0.1µF 6.8µF 0.1µF DIS RB 146Ω 50Ω Source RO 50Ω OPA690 50Ω Load RF 402Ω RG 200Ω RM 67Ω 0.1µF + 6.8µF –5V The second major consideration, touched on in the previous paragraph, is that the signal source impedance becomes part of the noise gain equation and hence influences the bandwidth. For the example in Figure 8, the RM value combines in parallel with the external 50Ω source impedance, yielding an effective driving impedance of 50Ω || 67Ω = 28.6Ω. This impedance is added in series with RG for calculating the noise gain (NG). The resultant NG is 2.8 for Figure 8, as opposed to only 2 if RM could be eliminated as discussed above. The bandwidth will therefore be slightly lower for the gain of –2 circuit of Figure 8 than for the gain of +2 circuit of Figure 1. The third important consideration in inverting amplifier design is setting the bias current cancellation resistor on the noninverting input (RB). If this resistor is set equal to the total DC resistance looking out of the inverting node, the output DC error, due to the input bias currents, will be reduced to (Input Offset Current) • RF. If the 50Ω source impedance is DC-coupled in Figure 8, the total resistance to ground on the inverting input will be 228Ω. Combining this in parallel with the feedback resistor gives the RB = 146Ω used in this example. To reduce the additional high frequency noise introduced by this resistor, it is sometimes bypassed with a capacitor. As long as RB < 350Ω, the capacitor is not required since the total noise contribution of all other terms will be less than that of the op amp’s input noise voltage. As a minimum, the OPA690 requires an RB value of 50Ω to damp out parasitic-induced peaking—a direct short to ground on the noninverting input runs the risk of a very high frequency instability in the input stage. FIGURE 8. Gain of –2 Example Circuit. OUTPUT CURRENT AND VOLTAGE In the inverting configuration, three key design considerations must be noted. The first is that the gain resistor (RG) becomes part of the signal channel input impedance. If input impedance matching is desired (which is beneficial whenever the signal is coupled through a cable, twisted-pair, long PC board trace, or other transmission line conductor), RG may be set equal to the required termination value and RF adjusted to give the desired gain. This is the simplest approach and results in optimum bandwidth and noise performance. However, at low inverting gains, the resultant feedback resistor value can present a significant load to the amplifier output. For an inverting gain of 2, setting RG to 50Ω for input matching eliminates the need for RM but requires a 100Ω feedback resistor. This has the interesting advantage that the noise gain becomes equal to 2 for a 50Ω source impedance—the same as the noninverting circuits considered above. However, the amplifier output will now see the 100Ω feedback resistor in parallel with the external load. In general, the feedback resistor should be limited to the 200Ω to 1.5kΩ range. In this case, it is preferable to increase both the RF and RG values, as shown in Figure 8, and then achieve the input matching impedance with a third resistor (RM) to ground. The total input impedance becomes the parallel combination of RG and RM. The OPA690 provides output voltage and current capabilities that are unsurpassed in a low-cost monolithic op amp. Under no-load conditions at +25°C, the output voltage typically swings closer than 1V to either supply rail; the tested swing limit is within 1.2V of either rail. Into a 15Ω load (the minimum tested load), it is tested to deliver more than ±160mA. The specifications described above, though familiar in the industry, consider voltage and current limits separately. In many applications, it is the voltage • current, or V-I product, which is more relevant to circuit operation. Refer to the “Output Voltage and Current Limitations” plot in the Typical Characteristics. The X- and Y-axes of this graph show the zero-voltage output current limit and the zero-current output voltage limit, respectively. The four quadrants give a more detailed view of the OPA690’s output drive capabilities, noting that the graph is bounded by a “Safe Operating Area” of 1W maximum internal power dissipation. Superimposing resistor load lines onto the plot shows that the OPA690 can drive ±2.5V into 25Ω or ±3.5V into 50Ω without exceeding the output capabilities or the 1W dissipation limit. A 100Ω load line (the standard test circuit load) shows the full ±3.9V output swing capability, as shown in the typical specifications. OPA690 SBOS223A www.ti.com 15 To protect the output stage from accidental shorts to ground and the power supplies, output short-circuit protection is included in the OPA690. The circuit acts to limit the maximum source or sink current to approximately 250mA. DRIVING CAPACITIVE LOADS One of the most demanding and yet very common load conditions for an op amp is capacitive loading. Often, the capacitive load is the input of an ADC—including additional external capacitance which may be recommended to improve ADC linearity. A high-speed, high open-loop gain amplifier like the OPA690 can be very susceptible to decreased stability and closed-loop response peaking when a capacitive load is placed directly on the output pin. When the amplifier’s open-loop output resistance is considered, this capacitive load introduces an additional pole in the signal path that can decrease the phase margin. Several external solutions to this problem have been suggested. When the primary considerations are frequency response flatness, pulse response fidelity, and/or distortion, the simplest and most effective solution is to isolate the capacitive load from the feedback loop by inserting a series isolation resistor between the amplifier output and the capacitive load. This does not eliminate the pole from the loop response, but rather shifts it and adds a zero at a higher frequency. The additional zero acts to cancel the phase lag from the capacitive load pole, thus increasing the phase margin and improving stability. The Typical Characteristics show the recommended RS versus capacitive load and the resulting frequency response at the load. Parasitic capacitive loads greater than 2pF can begin to degrade the performance of the OPA690. Long PC board traces, unmatched cables, and connections to multiple devices can easily exceed this value. Always consider this effect carefully, and add the recommended series resistor as close as possible to the OPA690 output pin (see Board Layout Guidelines). The criterion for setting this RS resistor is a maximum bandwidth, flat frequency response at the load. For the OPA690 operating in a gain of +2, the frequency response at the output pin is already slightly peaked without the capacitive load requiring relatively high values of RS to flatten the response at the load. Increasing the noise gain will reduce the peaking as described previously. The circuit of 16 Figure 9 demonstrates this technique, allowing lower values of RS to be used for a given capacitive load. +5V 50Ω 175Ω Power-supply decoupling not shown. 50Ω R RNG VO OPA690 CL 402Ω 402Ω –5V FIGURE 9. Capacitive Load Driving with Noise Gain Tuning. This gain of +2 circuit includes a noise gain tuning resistor across the two inputs to increase the noise gain, increasing the unloaded phase margin for the op amp. Although this technique will reduce the required RS resistor for a given capacitive load, it does increase the noise at the output. It also will decrease the loop gain, slightly decreasing the distortion performance. If, however, the dominant distortion mechanism arises from a high RS value, significant dynamic range improvement can be achieved using this technique. Figure 10 shows the required RS versus CLOAD parametric on noise gain using this technique. This is the circuit of Figure 9 with RNG adjusted to increase the noise gain (increasing the phase margin) then sweeping CLOAD and finding the required RS to get a flat frequency response. This plot also gives the required RS versus CLOAD for the OPA690 operated at higher signal gains. 100 90 80 70 RS (Ω) The minimum specified output voltage and current specifications over temperature are set by worst-case simulations at the cold temperature extreme. Only at cold startup will the output current and voltage decrease to the numbers shown in the tested tables. As the output transistors deliver power, their junction temperatures will increase, decreasing their VBE’s (increasing the available output voltage swing) and increasing their current gains (increasing the available output current). In steady-state operation, the available output voltage and current will always be greater than that shown in the over-temperature specifications since the output stage junction temperatures will be higher than the minimum specified operating ambient. NG = 2 60 50 40 30 20 NG = 3 10 NG = 4 0 1 10 100 1000 Capacitive Load (pF) FIGURE 10. Required RS vs Noise Gain. DISTORTION PERFORMANCE The OPA690 provides good distortion performance into a 100Ω load on ±5V supplies. Relative to alternative solutions, it provides exceptional performance into lighter loads and/or operating on a single +5V supply. Generally, until the fundamental signal reaches very high frequency or power OPA690 www.ti.com SBOS223A levels, the 2nd-harmonic will dominate the distortion with a negligible 3rd-harmonic component. Focusing then on the 2nd-harmonic, increasing the load impedance improves distortion directly. Remember that the total load includes the feedback network; in the noninverting configuration (see Figure 1) this is sum of RF + RG, while in the inverting configuration, it is just RF. Also, providing an additional supply decoupling capacitor (0.1µF) between the supply pins (for bipolar operation) improves the 2nd-order distortion slightly (3dB to 6dB). In most op amps, increasing the output voltage swing increases harmonic distortion directly. The new output stage used in the OPA690 actually holds the difference between fundamental power and the 2nd- and 3rd-harmonic powers relatively constant with increasing output power until very large output swings are required (> 4Vp-p). This also shows up in the 2-tone, 3rd-order intermodulation spurious (IM3) response curves. The 3rd-order spurious levels are moderately low at low output power levels. The output stage continues to hold them low even as the fundamental power reaches very high levels. As the Typical Characteristics show, the spurious intermodulation powers do not increase as predicted by a traditional intercept model. As the fundamental power level increases, the dynamic range does not decrease significantly. For 2 tones centered at 20MHz, with 10dBm/tone into a matched 50Ω load (i.e., 2Vp-p for each tone at the load, which requires 8Vp-p for the overall 2-tone envelope at the output pin), the Typical Characteristics show 47dBc difference between the test tone powers and the 3rdorder intermodulation spurious powers. This performance improves further when operating at lower frequencies. NOISE PERFORMANCE High slew rate, unity-gain stable, voltage feedback op amps usually achieve their slew rate at the expense of a higher input noise voltage. The 5.5nV/√Hz input voltage noise for the OPA690 is, however, much lower than comparable amplifiers. The input-referred voltage noise, and the two input-referred current noise terms, combine to give low output noise under a wide variety of operating conditions. Figure 11 shows the op amp noise analysis model with all the noise terms included. In this model, all noise terms are taken to be noise voltage or current density terms in either nV/√Hz or pA/√Hz. ENI EO OPA690 RS IBN ERS RF √ 4kTRS 4kT RG RG IBI √ 4kTRF 4kT = 1.6E –20J at 290°K The total output spot noise voltage can be computed as the square root of the sum of all squared output noise voltage contributors. Equation 1 shows the general form for the output noise voltage using the terms shown in Figure 11. (1) 2 2 EO = ENI2 + (IBNR S ) + 4kTRS NG2 + (IBIRF ) + 4kTRFNG Dividing this expression by the noise gain (NG = (1+RF /RG)) will give the equivalent input-referred spot noise voltage at the noninverting input, as shown in Equation 2. (2) 2 4kTRF 2 I R EN = ENI2 + (IBNR S ) + 4kTRS + BI F + NG NG Evaluating these two equations for the OPA690 circuit and component values (see Figure 1) will give a total output spot noise voltage of 12.3nV/√Hz and a total equivalent input spot noise voltage of 6.1nV/√Hz. This is including the noise added by the bias current cancellation resistor (175Ω) on the noninverting input. This total input-referred spot noise voltage is only slightly higher than the 5.5nV/√Hz specification for the op amp voltage noise alone. This will be the case as long as the impedances appearing at each op amp input are limited to the previously recommend maximum value of 300Ω. Keeping both (RF || RG) and the noninverting input source impedance less than 300Ω will satisfy both noise and frequency response flatness considerations. Since the resistor-induced noise is relatively negligible, additional capacitive decoupling across the bias current cancellation resistor (RB) for the inverting op amp configuration of Figure 8 is not required. DC ACCURACY AND OFFSET CONTROL The balanced input stage of a wideband voltage feedback op amp allows good output DC accuracy in a wide variety of applications. The power-supply current trim for the OPA690 gives even tighter control than comparable products. Although the high-speed input stage does require relatively high input bias current (typically ±8µA at each input terminal), the close matching between them may be used to reduce the output DC error caused by this current. The total output offset voltage may be considerably reduced by matching the DC source resistances appearing at the two inputs. This reduces the output DC error due to the input bias currents to the offset current times the feedback resistor. Evaluating the configuration of Figure 1, using worst-case +25°C input offset voltage and current specifications, gives a worst-case output offset voltage equal to: – (NG = noninverting signal gain) ±(NG • VOS(MAX)) ± (RF • IOS(MAX)) = ±(2 • 4mV) ± (402Ω • 1µA) = ±8.4mV FIGURE 11. Op Amp Noise Analysis Model. OPA690 SBOS223A www.ti.com 17 A fine-scale output offset null, or DC operating point adjustment, is often required. Numerous techniques are available for introducing DC offset control into an op amp circuit. Most of these techniques eventually reduce to adding a DC current through the feedback resistor. In selecting an offset trim method, one key consideration is the impact on the desired signal path frequency response. If the signal path is intended to be noninverting, the offset control is best applied as an inverting summing signal to avoid interaction with the signal source. If the signal path is intended to be inverting, applying the offset control to the noninverting input may be considered. However, the DC offset voltage on the summing junction will set up a DC current back into the source which must be considered. Applying an offset adjustment to the inverting op amp input can change the noise gain and frequency response flatness. For a DC-coupled inverting amplifier, Figure 12 shows one example of an offset adjustment technique that has minimal impact on the signal frequency response. In this case, the DC offsetting current is brought into the inverting input node through resistor values that are much larger than the signal path resistors. This will insure that the adjustment circuit has minimal effect on the loop gain and hence the frequency response. +5V Supply Decoupling Not Shown 328Ω OPA690 VO –5V RG 500Ω +5V 5kΩ RF 1kΩ VI 20kΩ ±200mV Output Adjustment 0.1µF VO VI =– RF RG Q1 25kΩ 110kΩ IS Control VDIS –VS FIGURE 13. Simplified Disable Control Circuit. LOW, additional current is pulled through the 15kΩ resistor, eventually turning on those two diodes (≈75µA). At this point, any further current pulled out of V DIS goes through those diodes holding the emitter-base voltage of Q1 at approximately 0V. This shuts off the collector current out of Q1, turning the amplifier off. The supply current in the disable mode are only those required to operate the circuit of Figure 13. Additional circuitry ensures that turn-on time occurs faster than turn-off time (make-before-break). When disabled, the output and input nodes go to a high impedance state. If the OPA690 is operating in a gain of +1, this will show a very high impedance at the output and exceptional signal isolation. If operating at a gain greater than +1, the total feedback network resistance (RF + RG) will appear as the impedance looking back into the output, but the circuit will still show very high forward and reverse isolation. If configured as an inverting amplifier, the input and output will be connected through the feedback network resistance (RF + RG) and the isolation will be very poor as a result. One key parameter in disable operation is the output glitch when switching in and out of the disabled mode. Figure 14 shows these glitches for the circuit of Figure 1 with the input signal at 0V. The glitch waveform at the output pin is plotted along with the DIS pin voltage. 10kΩ 5kΩ 15kΩ = –2 –5V FIGURE 12. DC-Coupled, Inverting Gain of –2, with Offset Adjustment. DISABLE/ENABLE GLITCH 6 DISABLE OPERATION In normal operation, base current to Q1 is provided through the 110kΩ resistor, while the emitter current through the 15kΩ resistor sets up a voltage drop that is inadequate to turn on the two diodes in Q1’s emitter. As V DIS is pulled 2 0 Output Voltage (10mV/div) The OPA690 provides an optional disable feature that may be used either to reduce system power or to implement a simple channel multiplexing operation. If the DIS control pin is left unconnected, the OPA690 will operate normally. To disable, the control pin must be asserted LOW. Figure 13 shows a simplified internal circuit for the disable control feature. 18 4 VDIS VDIS (2V/div) 0.1µF +VS 30 20 10 0 –10 Output Voltage Vi = 0V –20 –30 Time (20ns/div) FIGURE 14. Disable/Enable Glitch. OPA690 www.ti.com SBOS223A The transition edge rate (dv/dt) of the DIS control line will influence this glitch. For the plot of Figure 14, the edge rate was reduced until no further reduction in glitch amplitude was observed. This approximately 1V/ns maximum slew rate may be achieved by adding a simple RC filter into the DIS pin from a higher speed logic line. If extremely fast transition logic is used, a 1kΩ series resistor between the logic gate and the DIS input pin will provide adequate bandlimiting using just the parasitic input capacitance on the DIS pin while still ensuring adequate logic level swing. THERMAL ANALYSIS Due to the high output power capability of the OPA690, heatsinking or forced airflow may be required under extreme operating conditions. Maximum desired junction temperature will set the maximum allowed internal power dissipation as described below. In no case should the maximum junction temperature be allowed to exceed 175°C. Operating junction temperature (TJ) is given by TA + PD • θJA. The total internal power dissipation (PD) is the sum of quiescent power (PDQ) and additional power dissipated in the output stage (PDL) to deliver load power. Quiescent power is simply the specified no-load supply current times the total supply voltage across the part. PDL will depend on the required output signal and load but would, for a grounded resistive load, be at a maximum when the output is fixed at a voltage equal to 1/2 of either supply voltage (for equal bipolar supplies). Under this condition, PDL = VS2/(4 • RL) where RL includes feedback network loading. Note that it is the power in the output stage and not into the load that determines internal power dissipation. As a worst-case example, compute the maximum TJ using an OPA690IDBV (SOT23-6 package) in the circuit of Figure 1 operating at the maximum specified ambient temperature of +85°C and driving a grounded 20Ω load. PD = 10V • 6.2mA + 52/(4 • (20Ω || 804Ω)) = 382mW Maximum TJ = +85°C + (0.38W • 150°C/W) = 142°C. Although this is still well below the specified maximum junction temperature, system reliability considerations may require lower tested junction temperatures. The highest possible internal dissipation will occur if the load requires current to be forced into the output for positive output voltages or sourced from the output for negative output voltages. This puts a high current through a large internal voltage drop in the output transistors. The output V-I plot shown in the Typical Characteristics include a boundary for 1W maximum internal power dissipation under these conditions. BOARD LAYOUT GUIDELINES Achieving optimum performance with a high-frequency amplifier like the OPA690 requires careful attention to board layout parasitics and external component types. Recommendations that will optimize performance include: a) Minimize parasitic capacitance to any AC ground for all of the signal I/O pins. Parasitic capacitance on the output and inverting input pins can cause instability: on the noninverting input, it can react with the source impedance to cause unintentional bandlimiting. To reduce unwanted capacitance, a window around the signal I/O pins should be opened in all of the ground and power planes around those pins. Otherwise, ground and power planes should be unbroken elsewhere on the board. b) Minimize the distance (< 0.25") from the power-supply pins to high-frequency 0.1µF decoupling capacitors. At the device pins, the ground and power plane layout should not be in close proximity to the signal I/O pins. Avoid narrow power and ground traces to minimize inductance between the pins and the decoupling capacitors. The power-supply connections should always be decoupled with these capacitors. An optional supply decoupling capacitor (0.1µF) across the two power supplies (for bipolar operation) will improve 2nd-harmonic distortion performance. Larger (2.2µF to 6.8µF) decoupling capacitors, effective at lower frequency, should also be used on the main supply pins. These may be placed somewhat farther from the device and may be shared among several devices in the same area of the PC board. c) Careful selection and placement of external components will preserve the high-frequency performance of the OPA690. Resistors should be a very low reactance type. Surface-mount resistors work best and allow a tighter overall layout. Metal film or carbon composition axially-leaded resistors can also provide good high-frequency performance. Again, keep their leads and PC board traces as short as possible. Never use wirewound type resistors in a highfrequency application. Since the output pin and inverting input pin are the most sensitive to parasitic capacitance, always position the feedback and series output resistor, if any, as close as possible to the output pin. Other network components, such as noninverting input termination resistors, should also be placed close to the package. Where double-side component mounting is allowed, place the feedback resistor directly under the package on the other side of the board between the output and inverting input pins. Even with a low parasitic capacitance shunting the external resistors, excessively high resistor values can create significant time constants that can degrade performance. Good axial metal film or surface-mount resistors have approximately 0.2pF in shunt with the resistor. For resistor values > 1.5kΩ, this parasitic capacitance can add a pole and/or zero below 500MHz that can effect circuit operation. Keep resistor values as low as possible consistent with load driving considerations. The 402Ω feedback used in the Electrical Characteristics is a good starting point for design. Note that a 25Ω feedback resistor, rather than a direct short, is suggested for the unity-gain follower application. This effectively isolates the inverting input capacitance from the output pin that would otherwise cause an additional peaking in the gain of +1 frequency response. OPA690 SBOS223A www.ti.com 19 d) Connections to other wideband devices on the board may be made with short, direct traces or through onboard transmission lines. For short connections, consider the trace and the input to the next device as a lumped capacitive load. Relatively wide traces (50mils to 100mils) should be used, preferably with ground and power planes opened up around them. Estimate the total capacitive load and set RS from the plot of Recommended RS vs Capacitive Load. Low parasitic capacitive loads (< 5pF) may not need an RS since the OPA690 is nominally compensated to operate with a 2pF parasitic load. Higher parasitic capacitive loads without an RS are allowed as the signal gain increases (increasing the unloaded phase margin). If a long trace is required, and the 6dB signal loss intrinsic to a doubly terminated transmission line is acceptable, implement a matched impedance transmission line using microstrip or stripline techniques (consult an ECL design handbook for microstrip and stripline layout techniques). A 50Ω environment is normally not necessary on board, and in fact, a higher impedance environment will improve distortion as shown in the distortion versus load plots. With a characteristic board trace impedance defined (based on board material and trace dimensions), a matching series resistor into the trace from the output of the OPA690 is used as well as a terminating shunt resistor at the input of the destination device. Remember also that the terminating impedance will be the parallel combination of the shunt resistor and the input impedance of the destination device; this total effective impedance should be set to match the trace impedance. The high output voltage and current capability of the OPA690 allows multiple destination devices to be handled as separate transmission lines, each with their own series and shunt terminations. If the 6dB attenuation of a doubly-terminated transmission line is unacceptable, a long trace can be series-terminated at the source end only. Treat the trace as a capacitive load in this case and set the series resistor value as shown in the plot of “Recommended RS vs Capacitive Load”. This will not preserve signal integrity as well as a doubly-terminated line. If the input impedance of the destination device is low, there will be some signal attenuation due to the voltage divider formed by the series output into the terminating impedance. 20 e) Socketing a high-speed part like the OPA690 is not recommended. The additional lead length and pin-to-pin capacitance introduced by the socket can create an extremely troublesome parasitic network which can make it almost impossible to achieve a smooth, stable frequency response. Best results are obtained by soldering the OPA690 onto the board. INPUT AND ESD PROTECTION The OPA690 is built using a very high-speed complementary bipolar process. The internal junction breakdown voltages are relatively low for these very small geometry devices. These breakdowns are reflected in the Absolute Maximum Ratings table. All device pins are protected with internal ESD protection diodes to the power supplies as shown in Figure 15. +V CC External Pin Internal Circuitry –V CC FIGURE 15. Internal ESD Protection. These diodes provide moderate protection to input overdrive voltages above the supplies as well. The protection diodes can typically support 30mA continuous current. Where higher currents are possible (e.g., in systems with ±15V supply parts driving into the OPA690), current-limiting series resistors should be added into the two inputs. Keep these resistor values as low as possible since high values degrade both noise performance and frequency response. OPA690 www.ti.com SBOS223A PACKAGE DRAWINGS MSOI002B – JANUARY 1995 – REVISED SEPTEMBER 2001 D (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 8 PINS SHOWN 0.020 (0,51) 0.014 (0,35) 0.050 (1,27) 8 0.010 (0,25) 5 0.008 (0,20) NOM 0.244 (6,20) 0.228 (5,80) 0.157 (4,00) 0.150 (3,81) Gage Plane 1 4 0.010 (0,25) 0°– 8° A 0.044 (1,12) 0.016 (0,40) Seating Plane 0.010 (0,25) 0.004 (0,10) 0.069 (1,75) MAX PINS ** 0.004 (0,10) 8 14 16 A MAX 0.197 (5,00) 0.344 (8,75) 0.394 (10,00) A MIN 0.189 (4,80) 0.337 (8,55) 0.386 (9,80) DIM 4040047/E 09/01 NOTES: A. B. C. D. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15). Falls within JEDEC MS-012 OPA690 SBOS223A www.ti.com 21 PACKAGE DRAWINGS (Cont.) MPDS026C – FEBRUARY 1997 – REVISED JANUARY 2001 DBV (R-PDSO-G6) PLASTIC SMALL-OUTLINE 0,95 6X 6 0,50 0,25 0,20 M 4 1,70 1,50 1 0,15 NOM 3,00 2,60 3 Gage Plane 3,00 2,80 0,25 0°–8° 0,55 0,35 Seating Plane 1,45 0,95 0,05 MIN 0,10 4073253-5/F 10/00 NOTES: A. B. C. D. 22 All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion. Leads 1, 2, 3 are wider than leads 4, 5, 6 for package orientation. OPA690 www.ti.com SBOS223A PACKAGE OPTION ADDENDUM www.ti.com 3-Oct-2003 PACKAGING INFORMATION ORDERABLE DEVICE STATUS(1) PACKAGE TYPE PACKAGE DRAWING PINS PACKAGE QTY OPA690ID ACTIVE SOIC D 8 100 OPA690IDBVR ACTIVE SOP DBV 6 3000 OPA690IDBVT ACTIVE SOP DBV 6 250 OPA690IDR ACTIVE SOIC D 8 2500 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Applications amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2003, Texas Instruments Incorporated