Ordering number : ENA1931A STK672-732B-E Thick-Film Hybrid IC 2-phase Stepping Motor Driver Overview The STK672-732B-E is a hybrid IC for use as a unipolar, 2-phase stepping motor driver with PWM current control. Applications • Office photocopiers, printers, etc. Features • Built-in motor terminal open detection function (output current OFF). • Built-in overcurrent detection function (output current OFF). • Built-in overheat detection function (output current OFF). • FAULT signal (active low) is output when any of motor terminal open, overcurrent, or overheat is detected. The FAULT2 signal is used to output the result of activation of protection circuit detection at 3 levels. • Built-in power on reset function. • Phase signal input driver activated with an active Low and incorporates a simultaneous ON prevention function. • Supports schmitt input for 2.5V high level input. • Incorporating a current detection resistor (0.141Ω: resistor tolerance ±2%), motor current can be set using two external resistors. • Provides the output current cutoff ENABLE pin. Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. 70611HKPC 018-10-0062/32311HKPC No. A1931-1/23 STK672-732B-E Specifications Absolute Maximum Ratings at Tc = 25°C Parameter Symbol Conditions Ratings unit Maximum supply voltage 1 VCC max No signal 50 V Maximum supply voltage 2 VDD max No signal -0.3 to +6.0 V Input voltage VIN max Logic input pins -0.3 to +6.0 V Output current 1 IOP max 10μs, 1 pulse (resistance load) 10 A Output current 2 IOH max VDD=5V, CLOCK≥200Hz 2.65 A Output current 3 IOF max Pin16 output current 10 Allowable power dissipation 1 PdMF max With an arbitrarily large heat sink. Per MOSFET 7.3 W Allowable power dissipation 2 PdPK max No heat sink 2.8 W Operating substrate temperature Tc Metal surface temperature of the package -20 to +105 °C Junction temperature Tj max 150 °C Storage temperature Tstg -40 to +125 °C mA Allowable Operating Ranges at Ta=25°C Parameter Symbol Conditions Ratings unit Operating supply voltage 1 VCC With signals applied 0 to 46 V Operating supply voltage 2 VDD With signals applied 5±5% V Input high voltage VIH Pins 13, 17, 12, 10, 14, 15 2.5 to VDD V 0 to 0.8 V 2.0 A 2.2 A 0.14 to 1.38 V Input low voltage VIL Pins 13, 17, 12, 10, 14, 15 Output current 1 IOH1 Tc=105°C, CLOCK≥200Hz, Continuous operation, duty=100% Output current 2 IOH2 Tc=80°C, CLOCK≥200Hz, Continuous operation, duty=100%, See the motor current (IOH) derating curve Recommended Vref range Vref (* CLOCK ≥ 200Hz is the same as 200pps or more.) Electrical Characteristics at Tc=25°C, VCC=24V, VDD=5.0V Parameter Symbol Conditions VDD supply current ICCO Pin 9 current Output average current Ioave R/L=1Ω/0.62mH in each phase FET diode forward voltage Vdf If=1A (RL=23Ω) Output saturation voltage Vsat RL=23Ω Input high voltage VIH Pins 13, 17, 12, 10, 14, 15 Input low voltage VIL Pins 13, 17, 12, 10, 14, 15 FAULT1 low output voltage VOLF Pin 16 (IO=5mA) 5V level FAULT1 leakage IILF Pin 16=5V VOF1 Pin 8 (when all protection functions have min typ 0.273 max unit 5 8 0.329 0.385 A 0.92 1.6 V 0.33 0.48 V 2.5 mA V 0.8 0.25 V 0.5 V 10 μA current FAULT2 Motor terminal open 0.00 0.01 0.20 VOF2 2.4 2.5 2.6 VOF3 3.1 3.3 3.5 50 75 been activated) detection output voltage FAULT2 Overcurrent detection output voltage FAULT2 Overheat detection V output voltage 5V level input current IILH Pins 13, 17, 12, 10, 14, 15=5V GND level input current IILL Pins 13, 17, 12, 10, 14, 15=GND Vref input bias current IIB Pin 19=1.0V PWM frequency fc Overheat detection temperature TSD Design guarantee Drain-source cut-off current IDSS VDS=100V, Pins 2, 6, 9, 18=GND 29 45 μA 10 μA 1 μA 61 kHz 1 μA °C 144 * Operation at the maximum VCC value may not be possible, depending on the motor current. See “8. Other Notes on Use” in the Data Sheet for details. *Ioave values are for when the lead frame of the product is soldered to the mounting substrate. Notes: A fixed-voltage power supply must be used. No. A1931-2/23 STK672-732B-E Package Dimensions unit:mm (typ) 24.2 (18.4) 4.5 11.0 (11.0) 14.4 14.4 (R1.47) 19 (3.5) 1 1.0 0.4 0.5 2.0 18 1.0=18.0 4.0 4.45 Derating curve of motor current, IOH, vs. STK672-732B-E Operating substrate temperature, Tc IOH - Tc 3.0 200Hz 2-phase excitation Motor current, IOH - A 2.5 Hold mode 2.0 1.5 1.0 0.5 0 0 10 20 30 40 50 60 70 80 90 Operating Substrate Temperature, Tc- °C 100 110 ITF02548 Notes • The current range given above represents conditions when output voltage is not in the avalanche state. If the output voltage is in the avalanche state, see the allowable avalanche energy for STK672-7** series hybrid ICs given in a separate document. • The operating substrate temperature, Tc, given above is measured while the motor is operating. Because Tc varies depending on the ambient temperature, Ta, the value of IOH, and the continuous or intermittent operation of IOH, always verify this value using an actual set. • The Tc temperature should be checked in the center of the metal surface of the product package. No. A1931-3/23 STK672-732B-E Block Diagram VDD=5V 9 φBB 10 FAULT2 N.C A AB B BB 8 4 5 7 3 1 VDD BBIN F1 N.C 11 BIN FAO φAB 17 FAB φB 12 FBO φA 13 RESETB 14 ABIN F3 F4 FBB AIN R1 Power on reset Latch circuit Over current detection Latch circuit Output open detection R2 P.G2 ENABLE 15 FAULT1 16 F2 2 FAULT1 FAULT2 signal P.G1 Current control chopper circuit AI 6 BI Vref/4.9 Over heat detection Vref Latch circuit Amplifier VSS VSS N.C 18 Vref 19 No. A1931-4/23 STK672-732B-E Sample Application Circuit STK672-732B-E VDD(5V) 9 φA 13 φAB 17 φB 12 φBB 10 ENABLE 15 RESETB R01 2 phase stepping motor driver 5 7 3 14 1 A VCC 24V AB B BB + R03 C01 at least 100μF FAULT1 16 FAULT2 8 Vref 2 6 19 P.G2 P.GND P.G1 18 R02 N.C Precautions [GND wiring] • To reduce noise on the 5V system, be sure to place the GND of C01 in the circuit given above as close as possible to Pin 2 and Pin 6 of the hybrid IC. Also, to achieve accurate current settings, be sure to connect Vref GND to the point where P.G1 and P.G2 share a connection. [Input pins] • If VDD is being applied, use care that each input pin does not apply a negative voltage less than -0.3V to P.GND, and do not apply a voltage greater than or equal to VDD voltage. • Do not wire by connecting the circuit pattern on the P.C.B side to Pin 4, 11, or 18 on the N.C. shown in the internal block diagram. • Apply 2.5V high level input to pins 13, 17, 12, 10, 14, and 15. • Since the input pins do not have built-in pull-up resistors, when the open-collector type pins 13, 17, 12, 10, 14, and 15 are used as inputs, a 1 to 20kΩ pull-up resistor (to VDD) must be used. At this time, use a device for the open collector driver that has output current specifications that pull the voltage down to less than 0.8V at Low level (less than 0.8V at Low level when IOL=5mA). [Current setting Vref] If the motor current is temporarily reduced, the circuit given below (STK672-732B-E : IOH>0.2A) is recommended. 5V 5V R01 R01 Vref Vref R3 R02 R3 R02 No. A1931-5/23 STK672-732B-E • Motor current peak value IOH setting IOH 0 IOH=(Vref÷4.9) ÷Rs The value of 4.9 in Equation above represents the Vref voltage as divided by a circuit inside the control IC. Vref=(R02÷ (R01+R02)) ×5V(or 3.3V) Rs is an internal current detection resistor value of the hybrid IC. Rs=0.141Ω when using the STK672-732B-E Input Pin Functions Pin Name Pin No. Function Input Conditions When Operating φA 13 Pin 5, phase A output Low active (with a function to prevent simultaneous φAB 17 Pin 7, phase AB output ON of φA and φAB, or φB and φBB) φB 12 Pin 3, phase B output φBB 10 Pin 1, phase BB output RESETB 14 System reset A reset is applied by a low level ENABLE 15 A, AB, B, and, BB outputs cut off A, AB, B, and BB outputs are cut off by a low level Output Pin Functions Pin Name FAULT1 Pin No. 16 Function Monitor pin when any of motor terminal open, overcurrent, Input Conditions When Operating Low level is output when detected. or overheat is detected. FAULT2 8 Monitor pin used when over-current detection or overheat 3 levels output detection function is activated. Note: See the timing chart for the concrete details on circuit operation. No. A1931-6/23 STK672-732B-E Timing Charts 2-phase excitation VDD Power on reset (or RESETB) φA φAB φB φBB ENABLE FAO FAB FBO FBB 1-2 phase excitation VDD Power on reset (or RESETB) φA φAB φB φBB ENABLE FAO FAB FBO FBB No. A1931-7/23 STK672-732B-E 1-2 phase excitation (ENABLE) VDD Power on reset φA φAB φB φBB ENABLE FAO Output off FAB FBO FBB 1-2 phase excitation (Hold operation results during fixed CLOCK) VDD Power on reset (or RESETB) φA φAB φB φBB ENABLE Hold mode FAO FAB FBO FBB No. A1931-8/23 STK672-732B-E Usage Notes 1. STK672-732B-E Input signal functions and timing [ENABLE, power on reset, and RESETB (Input signal timing when power is first applied)] The control IC of the driver is equipped with a power on reset function capable of initializing internal IC operations when power is supplied. A 4V typ setting is used for power on reset. Because the specification for the MOSFET gate voltage is 5V±5%, conduction of current to output at the time of power on reset adds electromotive stress to the MOSFET due to lack of gate voltage. To prevent electromotive stress, be sure to set ENABLE=Low while VDD, which is outside the operating supply voltage, is less than 4.75V. 3.8V typ 4V typ Control IC power (VDD) rising edge Control IC power on reset RESETB signal input No time specification ENABLE signal input φA to φBB signal No time specification No time specification ENABLE, φA to φBB Signals Input Timing [ENABLE (Forcible on/off control of the A, AB, B, and BB outputs, and hybrid IC internal operation)] ENABLE=1: Normal operation ENABLE=0: Outputs A, AB, B, and BB forced to the off state. If the φA to φBB signal used for motor rotation suddenly stops, the motor shaft may advance beyond the control position due to inertia. A SLOW DOWN setting where the φA to φBB cycle gradually decreases is required in order to stop at the control position. No. A1931-9/23 STK672-732B-E [Configuration of Each Input Pin] <Configuration of the φA, φAB, φB, φBB, ENABLE, and RESETB input pins> <Configuration of the FAULT2 pin> 5V Output pin Pin 8 10kΩ Input pin 5V 50kΩ 50kΩ 50kΩ 100kΩ VSS Motor terminal open Overcurrent Overheating (The buffer has an open drain configuration.) All input pins of this driver support schmitt input. Typ specifications at Tc = 25°C are given below. Hysteresis voltage is 0.3V (VIHa-VILa). When rising When falling 1.8V typ 1.5V typ Input voltage VILa VIHa Input voltage specifications are as follows. VIH=2.5V min VIL=0.8V max <Configuration of the Vref input pin> <Configuration of the FAULT1 output pin> 5V Output pin Pin 16 Vref/4.9 − Amplifier VSS Motor terminal open Overcurrent Overheating + Input pin Pin 19 VSS <FAULT1, FAULT2 output> FAULT1 Output FAULT1 is an open drain output. It outputs low level when any of motor terminal open, overcurrent, or overheat is detected. FAULT2 output Output is resistance divided (3 levels) and the type of abnormality detected is converted to the corresponding output voltage. • Motor terminal open: 10mV (typ) • Overcurrent: 2.5V (typ) • Overheat: 3.3V (typ) Abnormality detection can be released by a RESETB operation or turning VDD voltage on/off. No. A1931-10/23 STK672-732B-E 2. STK672-732B-E overcurrent detection, overheat detection, and motor terminal open detection functions Each detection function operates using a latch system and turns output off. Because a RESET signal is required to restore output operations, once the power supply, VDD, is turned off, you must either again apply power on reset with VDDON or apply a RESETB=High→Low→High signal. [Motor terminal open detection] This hybrid IC is equipped with a function for detecting open output terminals to prevent thermal destruction of the MOSFET due to repeated avalanche operation that occurs when an output terminal connected to the motor is open. The open condition is determined by checking the presence or absence of the flyback current that flows in the motor inductance during the off period of the PWM cycle. Detection is performed by using the fact that the flyback current does not flow when a motor terminal is open. Terminal open Used to set the motor current Current detection resistor voltage 0V (GND potential) Used for open detection (Negative current does not flow when the terminal is open.) MOSFET gate signal PWM period When the current level drops, the difference with the GND potential decreases, making detection difficult. The motor current that can be detected by motor terminal open detection is 0.7A or more with the STK672-732B-E. <Notes on the ENABLE high edge> When ENABLE changes from low to high and the STK672-7XXB-E performs constant-current PWM operation that flows a negative current during the 30μs period after the high edge, open detection may activate and stop the driver. The motor current setting voltage Vref must be set so that PWM operation is not performed within a period of 30μs after the high edge. If the motor current setup voltage is set for the rated motor current, PWM operation is not performed during this 30μs period after the high edge, so this is not a problem. In addition, there is no problem with operation that lowers the current setting Vref after the motor rated current is reached as shown in the diagram on the following page. Whether constant-current PWM operation is performed during the 30μs period after the high edge can be judged by substituting the motor L and R values into the formula on the following page. Vref= (R02÷ (R01+R02)) ×5V (or 3.3V) IOH1= (Vref÷4.9) ÷Rs IOH1: Motor current value to be set IOH2= (VCC÷R) × (1-e-tR/L) IOH2: Current value 30μs after the ENABLE high edge ⇒ Judgment standard: IOH1>IOH2 R01, R02, 5V (or 3.3V): See the Sample Application Circuit documents. Rs: Current detection resistance value (Ω) VCC: Motor supply voltage (V) R: Motor winding resistance (Ω) L: Motor winding inductance (H) ⇒ There is no problem if the IOH2 obtained by substituting t = 30μs and the motor L and R values is smaller than the current setting value IOH1. No. A1931-11/23 STK672-732B-E ENABLE Vref Output current Constant-current PWM operation must not be performed for 30μs or less. <Connection of capacitors between output pins and GND prohibited> Capacitors must not be connected between the phase A (pin 5), phase AB (pin 7), phase B (pin 3) and phase BB (pin 1) outputs and GND. What happens if capacitors are connected is that open-circuit detection may be triggered by the discharge current of the capacitors when the internal MOSFET is set ON. This current is not an inductance current generated by the motor winding but a capacitor current so a negative current will not flow to the other phase in each pair of phases, possibly causing the driver to shut down. <Excessive external noise> If, when the motor current rises prior to the PWM operation, a spike-shaped current exceeding the Vref-setting current is generated by excessive external noise, for instance, before the current level (0.7A for the STK672-732B-E motor driver) at which motor pin open-circuiting can be detected is reached, the internal MOSFET is set OFF. Since the MOSFET has been set OFF before the actual motor current reaches 0.7A, the level of the negative current subsequently flowing to the other phase in each pair of phases is low, and it may be judged that no negative current is flowing, possibly causing open-circuit detection to be triggered. During normal constant-current PWM operation, the duration of 5.5μs, which is equivalent to 25% of the initial operation in the PWM period, corresponds to the section where the current is not detected, and this ensures that no current is detected for the linking part of the current that is generated in this section. The no-current detection section is not synchronized at the current rise prior to the PWM operation so when a spike-shaped current exceeding the Vref-setting current is generated, the MOSFET is set OFF at the stage where the level of the actual motor current is low. As a result, the level of the negative current subsequently flowing to the other phase in each pair of phases is low, and it may be judged that no negative current is flowing, possibly causing open-circuit detection to be triggered. Spike-shaped current Vref setting current (IOH) Motor current Current level at which opencircuiting is detected No-current detection time (5.5μs typ) PWM period No. A1931-12/23 STK672-732B-E [Overcurrent detection] This hybrid IC is equipped with a function for detecting overcurrent that arises when the motor burns out or when there is a short between the motor terminals. Overcurrent detection occurs at 3.5A typ with the STK672-732B-E Current when motor terminals are shorted PWM period Set motor current, IOH Over-current detection IOH max MOSFET all OFF No detection interval (5.5μs typ) Normal operation 5.5μs typ Operation when motor pins are shorted Overcurrent detection begins after an interval of no detection (a dead time of 5.5μs typ) during the initial ringing part during PWM operations. The no detection interval is a period of time where overcurrent is not detected even if the current exceeds IOH. [Overheat detection] Rather than directly detecting the temperature of the semiconductor device, overheat detection detects the temperature of the aluminum substrate (144°C typ). Within the allowed operating range recommended in the specification manual, if a heat sink attached for the purpose of reducing the operating substrate temperature, Tc, comes loose, the semiconductor can operate without breaking. However, we cannot guarantee operations without breaking in the case of operations other than those recommended, such as operations at a current exceeding IOH max that occurs before overcurrent detection is activated. No. A1931-13/23 STK672-732B-E 3. Calculating STK672-732B-E HIC Internal Power Loss The average internal power loss in each excitation mode of the STK672-732B-E can be calculated from the following formulas. Each excitation mode 2-phase excitation mode 2PdAVex= (Vsat+Vdf)× (1/ (t1+t2+t3))×IOH×t2+ (1/ (t1+t2+t3))×IOH× (Vsat×t1+Vdf×t3) 1-2 Phase excitation mode 1-2PdAVex= (Vsat+Vdf)× (1/ (t1+t2+t3))×IOH×t2+ (1/ (t1+t2+t3))×IOH× (Vsat×t1+Vdf×t3) Motor hold mode HoldPdAVex= (Vsat+Vdf)×IOH Vsat: Combined voltage represented by the Ron voltage drop + shunt resistor Vdf: Combined voltage represented by the MOSFET body diode + shunt resistor t1, t2, and t3 represent the waveforms shown in the figure below. t1: Time required for the winding current to reach the set current (IOH) t2: Time in the constant current control (PWM) region t3: Time from end of phase input signal until inverse current regeneration is complete IOH 0A t1 t2 t3 Motor COM Current Waveform Model t1= (-L/(R+0.33)) ln (1-((R+0.33)/VCC) ×IOH) t3= (-L/R) ln ((VCC+0.33)/(IOH×R+VCC+0.33)) VCC: Motor supply voltage (V) L: Motor inductance (H) R: Motor winding resistance (Ω) IOH: Motor set output current crest value (A) For Vsat and Vdf, be sure to substitute values from the graphs of Vsat vs. IOH and Vdf vs. IOH while the set current value is IOH. Then, determine whether a heat sink is required by comparing with the graph of ΔTc vs. Pd based on the average HIC power loss calculated. When designing a heat sink, refer to the section “Thermal design” found on the next page. The average HIC power loss, PdAV, described above does not have the avalanche’s loss. To include the avalanche’s loss, be sure to add Equation (2), “STK672-7** Allowable Avalanche Energy Value” to PdAV above. When using this IC without a fin always check for temperature increases in the set, because the HIC substrate temperature, Tc, varies due to effects of convection around the HIC. No. A1931-14/23 STK672-732B-E STK672-732B-E Output saturation voltage, Vsat - Output current, IOH Vsat - IOH 05 °C 0.8 0.6 Tc =1 Output saturation voltage, Vsat - V 1.0 °C 25 0.4 0.2 0 0 0.5 1.0 1.5 2.0 2.5 Output current, IOH - A 3.0 ITF02571 STK672-732B-E Forward voltage, Vdf -Output current, IOH Vdf- IOH 1.4 Forward voltage, Vdf - V 1.2 25°C Tc= C 105° 1.0 0.8 0.6 0.4 0.2 0 0 0.5 1.0 1.5 2.0 2.5 Output current, IOH - A 3.0 ITF02572 Substrate temperature rise, ΔTc (no heat sink) - Internal average power dissipation, PdAV ΔTc - PdAV Substrate temperature rise, ΔTc - °C 80 70 60 50 40 30 20 10 0 0 0.5 1.0 1.5 2.0 2.5 Hybrid IC internal average power dissipation, PdAV - W 3.0 ITF02717 No. A1931-15/23 STK672-732B-E 4. STK672-732B-E Allowable Avalanche Energy Value (1) Allowable Range in Avalanche Mode When driving a 2-phase stepping motor with constant current chopping using an STK672-7** Series hybrid IC, the waveforms shown in Figure 1 below result for the output current, ID, and voltage, VDS. VDSS: Voltage during avalanche operations VDS IOH: Motor current peak value IAVL: Current during avalanche operations ID tAVL: Time of avalanche operations ITF02557 Figure 1 Output Current, ID, and Voltage, VDS, Waveforms 1 of the STK672-7** Series when Driving a 2-Phase Stepping Motor with Constant Current Chopping When operations of the MOSFET built into STK672-7** Series ICs is turned off for constant current chopping, the ID signal falls like the waveform shown in the figure above. At this time, the output voltage, VDS, suddenly rises due to electromagnetic induction generated by the motor coil. In the case of voltage that rises suddenly, voltage is restricted by the MOSFET VDSS. Voltage restriction by VDSS results in a MOSFET avalanche. During avalanche operations, ID flows and the instantaneous energy at this time, EAVL1, is represented by Equation (1). EAVL1=VDSS×IAVL×0.5×tAVL ------------------------------------------- (1) VDSS: V units, IAVL: A units, tAVL: sec units The coefficient 0.5 in Equation (1) is a constant required to convert the IAVL triangle wave to a square wave. During STK672-7** Series operations, the waveforms in the figure above repeat due to the constant current chopping operation. The allowable avalanche energy, EAVL, is therefore represented by Equation (2) used to find the average power loss, PAVL, during avalanche mode multiplied by the chopping frequency in Equation (1). PAVL=VDSS×IAVL×0.5×tAVL×fc ------------------------------------------- (2) fc: Hz units (fc is set to the PWM frequency of 50kHz.) For VDSS, IAVL, and tAVL, be sure to actually operate the STK672-7** Series and substitute values when operations are observed using an oscilloscope. Ex. If VDSS=110V, IAVL=1A, tAVL=0.2μs when using a STK672-732B-E driver, the result is: PAVL=110×1×0.5×0.2×10-6×50×103=0.55W VDSS=110V is a value actually measured using an oscilloscope. The allowable loss range for the allowable avalanche energy value, PAVL, is shown in the graph in Figure 3. When examining the avalanche energy, be sure to actually drive a motor and observe the ID, VDSS, and tAVL waveforms during operation, and then check that the result of calculating Equation (2) falls within the allowable range for avalanche operations. No. A1931-16/23 STK672-732B-E (2) ID and VDSS Operating Waveforms in Non-avalanche Mode Although the waveforms during avalanche mode are given in Figure 1, sometimes an avalanche does not result during actual operations. Factors causing avalanche are listed below. • Poor coupling of the motor’s phase coils (electromagnetic coupling of A phase and AB phase, B phase and BB phase). • Increase in the lead inductance of the harness caused by the circuit pattern of the P.C. board and motor. • Increases in VDSS, tAVL, and IAVL in Figure 1 due to an increase in the supply voltage from 24V to 36V. If the factors above are negligible, the waveforms shown in Figure 1 become waveforms without avalanche as shown in Figure 2. Under operations shown in Figure 2, avalanche does not occur and there is no need to consider the allowable loss range of PAVL shown in Figure 3. VDS IOH: Motor current peak value ID ITF02558 Figure 2 Output Current, ID, and Voltage, VDS, Waveforms 2 of the STK672-7** Series when Driving a 2-Phase Stepping Motor with Constant Current Chopping Average power loss in the avalanche state, PAVL- W Figure 3 Allowable Loss Range, PAVL-IOH During Avalanche Operations PAVL - IOH 4.0 3.5 Tc= 80° C 3.0 2.5 105 °C 2.0 1.5 1.0 0.5 0 0 0.5 1.0 1.5 Motor phase current, IOH - A 2.0 2.5 ITF02573 Note: The operating conditions given above represent a loss when driving a 2-phase stepping motor with constant current chopping. Because it is possible to apply 2.6W or more at IOH=0A, be sure to avoid using the MOSFET body diode that is used to drive the motor as a zener diode. No. A1931-17/23 STK672-732B-E 5. Thermal design [Operating range in which a heat sink is not used] Use of a heat sink to lower the operating substrate temperature of the HIC (Hybrid IC) is effective in increasing the quality of the HIC. The size of heat sink for the HIC varies depending on the magnitude of the average power loss, PdAV, within the HIC. The value of PdAV increases as the output current increases. To calculate PdAV, refer to “Calculating Internal HIC Loss for the STK672-732B-E”. Calculate the internal HIC loss, PdAV, assuming repeat operation such as shown in Figure 1 below, since conduction during motor rotation and off time both exist during actual motor operations, IO1 Motor phase current (sink side) IO2 0A -IO1 T1 T2 T3 T0 Figure 1 Motor Current Timing T1: Motor rotation operation time T2: Motor hold operation time T3: Motor current off time T2 may be reduced, depending on the application. T0: Single repeated motor operating cycle IO1 and IO2: Motor current peak values Due to the structure of motor windings, the phase current is a positive and negative current with a pulse form. Note that figure 1 presents the concepts here, and that the on/off duty of the actual signals will differ. The hybrid IC internal average power dissipation PdAV can be calculated from the following formula. PdAV= (T1×P1+T2×P2+T3×0) ÷TO ---------------------------- (I) (Here, P1 is the PdAV for IO1 and P2 is the PdAV for IO2) If the value calculated using Equation (I) is 1.5W or less, and the ambient temperature, Ta, is 60°C or less, there is no need to attach a heat sink. Refer to Figure 2 for operating substrate temperature data when no heat sink is used. [Operating range in which a heat sink is used] Although a heat sink is attached to lower Tc if PdAV increases, the resulting size can be found using the value of θc-a in Equation (II) below and the graph depicted in Figure 3. θc-a= (Tc max-Ta) ÷PdAV ---------------------------- (II) Tc max: Maximum operating substrate temperature =105°C Ta: HIC ambient temperature Although a heat sink can be designed based on equations (I) and (II) above, be sure to mount the HIC in a set and confirm that the substrate temperature, Tc, is 105°C or less. The average HIC power loss, PdAV, described above represents the power loss when there is no avalanche operation. To add the loss during avalanche operations, be sure to add Equation (2), “Allowable STK672-7** Avalanche Energy Value”, to PdAV. No. A1931-18/23 STK672-732B-E Figure 2 Substrate temperature rise, ΔTc (no heat sink) - Internal average power dissipation, PdAV ΔTc - PdAV 80 Substrate temperature rise, ΔTc - °C 70 60 50 40 30 20 10 0 0 0.5 1.0 1.5 2.0 2.5 3.0 Hybrid IC internal average power dissipation, PdAV - W ITF02717 Figure 3 Heat sink area (Board thickness: 2mm) - θc-a θc-a - S Heat sink thermal resistance, θc-a - °C/W 100 7 5 3 2 Wi t 10 Wi t 7 5 ha 3 2 1.0 10 2 3 5 hn o su rfac e fi nish flat blac k su rfac e fi nish 7 2 100 3 5 7 1000 Heat sink area, S - cm2 ITF02554 6. Mitigated Curve of Package Power Loss, PdPK, vs. Ambient Temperature, Ta Package power loss, PdPK, refers to the average internal power loss, PdAV, allowable without a heat sink. The figure below represents the allowable power loss, PdPK, vs. fluctuations in the ambient temperature, Ta. Power loss of up to 2.8W is allowable at Ta=25°C, and of up to 1.5W at Ta=60°C. Allowable power dissipation, PdPK(no heat sink) - Ambient temperature, Ta PdPK - Ta Allowable power dissipation, PdPK - W 3.0 2.5 2.0 1.0 1.5 0.5 0 0 20 40 60 80 Ambient Temperature, Ta - °C 100 120 ITF02718 No. A1931-19/23 STK672-732B-E 7. Example of Stepping Motor Driver Output Current Path (1-2 phase excitation) 2-phase stepping motor IOA FAULT2 8 VDD=5V 9 φBB 10 N.C 4 AB 7 F2 F1 FAO φAB 17 FAB φA 13 A 5 B 3 BB 1 VDD BBIN N.C 11 BIN φB 12 IOAB F3 F4 VCC 24V FBO ABIN FBB C02 at least 100μF AIN R1 Power on reset RESETB 14 Latch circuit Over current detection Latch circuit Output open detection P.G2 2 ENABLE 15 FAULT1 16 FAULT1 FAULT2 signal AI Current control chopper circuit R2 P.G1 6 P.GND BI Vref/4.9 Over heat detection N.C 18 Vref Latch circuit Amplifier VSS VSS Vref 19 φA(Pin 13) φAB(Pin 17) Phase A output current IOA PWM operations Phase AB output current When PWM operations of IOA are OFF, for IOAB, negative current flows through the parasitic diode, F2. IOAB When PWM operations of IOAB are OFF, for IOA, negative current flows through the parasitic diode, F1. No. A1931-20/23 STK672-732B-E 8. Other Notes on Use In addition to the “Notes” indicated in the Sample Application Circuit, care should also be given to the following contents during use. (1) Allowable operating range Operation of this product assumes use within the allowable operating range. If a supply voltage or an input voltage outside the allowable operating range is applied, an overvoltage may damage the internal control IC or the MOSFET. If a voltage application mode that exceeds the allowable operating range is anticipated, connect a fuse or take other measures to cut off power supply to the product. (2) Input pins If the input pins are connected directly to the PC board connectors, electrostatic discharge or other overvoltage outside the specified range may be applied from the connectors and may damage the product. Current generated by this overvoltage can be suppressed to effectively prevent damage by inserting 100Ω to 1kΩ resistors in lines connected to the input pins. Take measures such as inserting resistors in lines connected to the input pins. (3) Power connectors If the motor power supply VCC is applied by mistake without connecting the GND part of the power connector when the product is operated, such as for test purposes, an overcurrent flows through the VCC decoupling capacitor, C1, to the parasitic diode between the VDD of the internal control IC and GND, and may damage the power supply pin block of the internal control IC. To prevent destruction in this case, connect a 10Ω resistor to the VDD pin, or insert a diode between the VCC decoupling capacitor C1 GND and the VDD pin. Overcurrent protection measure: Insert a resistor. VDD=5V 5V Reg. 9 A 5 VDD AB 7 F1 B 3 F2 BB 1 F3 F4 FAO φA FABO FBO φAB FBBO VCC φB φBB R1 ENABLE AI RESETB BI R2 GND 2 C1 24V Reg. 6 Vref FAULT1 Vref 18 VSS N.C open Overcurrent protection measure: Insert a diode. Over-current path (4) Input Signal Lines 1) Do not use an IC socket to mount the driver, and instead solder the driver directly to the PC board to minimize fluctuations in the GND potential due to the influence of the resistance component and inductance component of the GND pattern wiring. 2) To reduce noise caused by electromagnetic induction to small signal lines, do not design small signal lines (sensor signal lines, and 5V or 3.3V power supply signal lines) that run parallel in close proximity to the motor output line A (Pin 5), AB (Pin 7), B (Pin 3), or BB (Pin 1) phases. 3) Pin 4, 11 and Pin 18 of this product are N.C pins. Do not connect any wiring to these pins. No. A1931-21/23 STK672-732B-E (5) When mounting multiple drivers on a single PC board When mounting multiple drivers on a single PC board, the GND design should mount a VCC decoupling capacitor, C1, for each driver to stabilize the GND potential of the other drivers. The key wiring points are as follows. 24V 5V 9 9 Motor 1 Input 9 Motor 2 Input Motor 3 Input IC2 IC1 IC3 2 2 6 6 2 6 19 18 19 18 19 18 GND GND Short Thick Thick and short (6) VCC operating limit When the output (for example F1) of a 2-phase stepping motor driver is turned OFF, the AB phase back electromotive force eab produced by current flowing to the paired F2 parasitic diode is induced in the F1 side, causing the output voltage VFB to become twice or more the VCC voltage. This is expressed by the following formula. VFB = VCC + eab = VCC + VCC + IOH × RM + Vdf (1.5 V) VCC: Motor supply voltage, IOH: Motor current set by Vref Vdf: Voltage drop due to F2 parasitic diode and current detection resistor R1, RM: Motor winding resistance value Using the above formula, make sure that VFB is always less than the MOSFET withstand voltage of 100V. This is because there is a possibility that operating limit of VCC falls below the allowable operating range of 46V, due to the RM and IOH specifications. VCC VCC AB phase A phase AB phase A phase eab eab is generated by the mutual induction M. Current path VFB M eab F2 OFF F1 ON R1 GND Current path M VCC F2 OFF F1 OFF R1 GND The oscillating voltage in excess of VFB is caused by LCRM (inductance, capacitor, resistor, mutual inductance) oscillation that includes micro capacitors C, not present in the circuit. Since M is affected by the motor characteristics, there is some difference in oscillating voltage according to the motor specifications. In addition, constant voltage drive without constant current drive enables motor rotation at VCC > 0V. No. A1931-22/23 STK672-732B-E SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellectual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of July, 2011. Specifications and information herein are subject to change without notice. PS No. A1931-23/23