Z00607 Standard 0.8 A Triacs Main Features A2 Symbol Value Unit IT(RMS) 0.8 A VDRM/VRRM 600 V IGT (Q1) 5 mA G A1 A2 Description A1 The Z00607 is suitable for low power AC switching applications. Typical applications include home appliances (electrovalve, pump, door lock, small lamp control), fan speed controllers,... TO-92 Z00607MA Part Number Marking Z00607MA 1BA2 Z0607MA Z00607MA 2BL2 Z0607MA Z00607MA 5BL2 Z0607MA Z00607MN 5AA4 Z6M Parameter RMS on-state current (full sine wave) SOT-223 Ttab = 85° C TO-92 TL = 50° C Non repetitive surge peak on-state current (full cycle, Tj initial = 25° C) F = 50 Hz t = 20 ms F = 60 Hz t = 16.7 ms I²t Value for fusing tp = 10 ms dI/dt Critical rate of rise of on-state current IG = 2 x IGT , tr ≤ 100 ns F = 120 Hz IGM Peak gate current tp = 20 µs ITSM I²t PG(AV) Tstg Tj April 2007 SOT-223 Z00607MN Absolute maximum ratings Symbol IT(RMS) A1 Order Codes Thanks to the low gate triggering current these triacs can be driven directly by microcontrollers. Table 1. G A2 A2 G Value Unit 0.8 A 9 A Average gate power dissipation Storage junction temperature range Operating junction temperature range Rev 8 9.5 0.45 A ²s Tj = 110° C 20 A/µs Tj = 110° C 1 A Tj = 110° C 0.1 W - 40 to + 150 - 40 to + 110 °C 1/7 www.st.com 7 Characteristcs 1 Z00607 Characteristcs Table 2. Electrical characteristics (Tj = 25° C, unless otherwise specified) Symbol Test Conditions Quadrant Value I - II - III IGT (1) 5 MAX VD = 12 V RL = 30 Ω IV VGT VGD VD = VDRM RL = 3.3 kΩ Tj = 110° C IH (2) IT = 200 mA IL IG = 1.2 IGT (dV/dt)c (2) mA 7 ALL MAX 1.3 V ALL MIN 0.2 V MX. 5 mA I - III - IV dV/dt (2) Unit 10 MAX II mA 20 VD = 67% VDRM gate open Tj = 110° C MIN 10 V/µs (dV/dt)c = 0.35 A/ms MIN 1.5 V/µs Tj = 110° C 1. minimum IGT is guaranteed at 5% of IGT max. 2. for both polarities of A2 referenced to A1. Table 3. Static characteristics Symbol Test Conditions VTM(1) ITM = 1.1 A Vto (1) Rd (1) IDRM IRRM tp = 380 µs Value Unit Tj = 25° C MAX. 1.5 V Threshold voltage Tj = 110° C MAX. 0.95 V Dynamic resistance Tj = 110° C MAX. 420 mΩ 5 µA 0.1 mA Value Unit Tj = 25° C VDRM = VRRM = 600 V Tj = 110° C MAX. 1. for both polarities of A2 referenced to A1. Table 4. Thermal resistances Symbol Parameter Rth(j-t) Junction to tab (AC) SOT-223 25 Rth(j-I) Junction to lead (AC) TO-92 60 Rth(j-a) Junction to ambient ° C/W S(1) = 5 cm² SOT-223 1. 2/7 S = Copper surface under tab. 60 ° C/W TO-92 150 Z00607 Characteristcs Figure 1. Maximum power dissipation versus RMS on-state current (full cycle) Figure 2. P(W) Relative variation of gate trigger current, holding current and latching current versus junction temperature (typical values) IGT, IH, IL [Tj] / IGT, IH, IL [Tj=25°C] 1.0 2.5 0.9 0.8 2.0 0.7 IGT 0.6 1.5 0.5 IH & IL 1.0 0.4 0.3 0.5 0.2 0.1 Tj (°C) IT(RMS)(A) 0.0 0.0 0.0 0.1 Figure 3. 0.2 0.3 0.4 0.5 0.6 0.7 0.8 -40 -20 Surge peak on-state current versus Figure 4. number of cycles 0 20 40 60 80 100 120 Non-repetitive surge peak on-state current for a sinusoidal pulse with width tp < 10 ms and corresponding value of I2t ITSM (A), I2t (A2s) ITSM (A) 10 200.0 9 100.0 Tj initial = 25°C t=20ms 8 dI/dt limitation: 20A/µs One cycle 7 ITSM Non repetitive Tj initial = 25°C 6 10.0 5 4 Repetitive Tamb = 25°C 3 1.0 I2t 2 1 tp (ms) Number of cycles 0 1 10 Figure 5. 0.1 100 0.01 1000 On-state characteristics (maximum values) Figure 6. ITM(A) 0.10 1.00 10.00 Relative variation of critical rate of decrease of main current versus (dV/dt)c (typical values) (dI/dt)c [(dV/dt)c] / Specified (dI/dt)c 10.0 10.0 8.0 6.0 Tj = Tjmax. 1.0 4.0 Tj=max. Vt0=0.95 V Rd=420 mΩ Tj = 25°C 2.0 VTM (V) 0.0 0.5 1.0 1.5 2.0 2.5 (dV/dt)c (V/µs) 0.0 0.1 3.0 3.5 4.0 4.5 5.0 0.1 1.0 10.0 3/7 Ordering information scheme Figure 7. Z00607 Relative variation of critical rate of decrease of main current versus junction temperature Figure 8. (dI/dt)c [Tj] / (dI/dt)c [Tj Specified] Rth(j-a)(°C/W) 6 130 120 110 100 90 80 70 60 50 40 30 20 10 0 5 4 3 2 1 Tj (°C) 0 0 2 10 20 30 40 50 60 SOT-223 Thermal resistance junction to ambient versus copper surface under tab (printed circuit board FR4, copper thickness: 35 µm) 70 80 90 100 110 S(cm²) 0.0 0.5 1.0 1.5 2.0 3.0 3.5 Ordering information scheme Z 006 07 M A Triac series Current 006 = 0.8A Sensitivity 07 = 5mA Voltage M = 600V Package A = TO-92 N = SOT-223 Packing mode 1BA2 = TO-92 Bulk 2BL2 = TO-92 Ammopack 5BL2 = TO-92 Tape and reel 5AA4 = SOT-223 Tape and reel 4/7 2.5 Blank 1BA2 4.0 4.5 5.0 Z00607 3 Packaging information Packaging information Table 5. SOT-223 Dimensions Dimensions Ref. V A A1 Millimeters Min. c Typ. A B A1 e1 Inches Max. Min. Typ. Max. 1.80 0.071 0.02 0.10 0.001 0.004 B 0.60 0.70 0.85 0.024 0.027 0.033 B1 2.90 3.00 3.15 0.114 0.118 0.124 c 0.24 0.26 0.35 0.009 0.010 0.014 (1) 6.30 6.50 6.70 0.248 0.256 0.264 D B1 D 4 H E 1 2 e 3 2.3 e1 e 0.090 4.6 0.181 E(1) 3.30 3.50 3.70 0.130 0.138 0.146 H 6.70 7.00 7.30 0.264 0.276 0.287 V 10° max 1. Do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15mm (0.006inches) Figure 9. Footprint (dimensions in mm) 3.25 1.32 5.16 7.80 1.32 2.30 0.95 5/7 Ordering information Z00607 Table 6. TO-92 Dimensions DIMENSIONS REF. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A a B A 1.35 B C 4.70 C F 4 5 6/7 D E 0.053 0.185 2.54 0.100 D 4.40 0.173 E 12.70 0.500 F 3.70 0.146 a 0.50 0.019 Ordering information Ordering type Marking Z00607MA 1BA2 Z0607MA Z00607MA 2BL2 Z0607MA Z00607MA 5BL2 Z0607MA Z00607MN 5AA4 Z6M Package TO-92 SOT-223 Weight 0.2 g 0.12 g Base quantity Delivery mode 2500 Bulk 2000 Ammopack 2000 Tape and reel 1000 Tape and reel Revision history Date Revision Description of Changes Oct-2001 4 Last update. 25-Mar-2005 5 Package: TO-92 tape and reel delivery mode 5BL2 added. 21-Jun-2005 6 Markings updated from Z006xxxx to Z06xxxx 13-Sep-2005 7 Z00607MA 2BL2: marking corrected from 00607mA to Z0607MA 12-Apr-2007 8 Reformatted to current standard. Added SOT-223 package. Changed Tj from +125 to +110 in Table 1 Z00607 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 7/7