TI TLE2425MD

TLE2425
PRECISION VIRTUAL GROUND
SLOS065D – MARCH 1991 – REVISED APRIL 2002
D
D
D
D
2.5-V Virtual Ground for 5-V/GND Analog
Systems
High Output-Current Capability
Sink or Source . . . 20 mA Typ
Micropower Operation . . . 170 µA Typ
Excellent Regulation Characteristics
– Output Regulation
– 45 µV Typ at IO = 0 to – 10 mA
+15 µV Typ at IO = 0 to + 10 mA
– Input Regulation = 1.5 µV/V Typ
Low-Impedance Output . . . 0.0075 Ω Typ
Macromodel Included
D
D
description
OUTPUT REGULATION
100
In signal-conditioning applications using a single
power source, a reference voltage is required for
termination of all signal grounds. To accomplish
this, engineers have typically used solutions
consisting of resistors, capacitors, operational
amplifiers, and voltage references. Texas Instruments has eliminated all of those components
with one easy-to-use 3-terminal device. That
device is the TLE2425 precision virtual ground.
VI = 5 V
∆VV)
O – Output Voltage Change – µV
80
Use of the TLE2425 over other typical circuit
solutions gives the designer increased dynamic
signal range, improved signal-to-noise ratio,
lower distortion, improved signal accuracy, and
easier interfacing to ADCs and DACs. These
benefits are the result of combining a precision
micropower voltage reference and a high-performance precision operational amplifier in a single
silicon chip. It is the precision and performance of
these two circuit functions together that yield such
dramatic system-level performance.
60
TA = – 40°C
40
TA = 0°C
TA = – 55°C
20
0
TA = 125°C
TA = 25°C
TA = 25°C
– 20
– 40
TA = 125°C
– 60
TA = – 55°C
– 80
– 100
– 10
–8
–6
–4 –2
0
2 4
6
IO – Output Current – mA
8
10
The TLE2425 improves input regulation as well as output regulation and, in addition, reduces output impedance
and power dissipation in a majority of virtual-ground-generation circuits. Both input regulation and load
regulation exceed 12 bits of accuracy on a single 5-V system. Signal-conditioning front ends of data acquisition
systems that push 12 bits and beyond can use the TLE2425 to eliminate a major source of system error.
AVAILABLE OPTIONS
TA
SMALL OUTLINE
(D)
PLASTIC
TO-226AA
(LP)
0°C to 70°C
TLE2425CD
TLE2425CD
– 40°C to 85°C
TLE2425ID
TLE2425ID
– 55°C to 125°C
TLE2425MD
—
† The D package is available taped and reeled. Add R suffix to
the device type (e.g., TLE2425CDR).
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2002, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
•
1
TLE2425
PRECISION VIRTUAL GROUND
SLOS065D – MARCH 1991 – REVISED APRIL 2002
D, OR JG PACKAGE
(TOP VIEW)
OUT
COMMON
IN
NC
1
8
2
7
3
6
4
5
LP PACKAGE
(TOP VIEW)
NC
NC
NC
NC
IN
COMMON
OUT
NC – No internal connection
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Continuous input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 V
Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±80 mA
Duration of short-circuit current at (or below) 25°C (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA: C-suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
I-suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 85°C
M-suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –55°C to 125°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D package . . . . . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: JG or LP package . . . . . . . . . . . . . . 300°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum dissipation
rating is not exceeded.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
TA = 125°C
POWER RATING
145 mW
D
725 mV
5.8 mW/°C
464 mW
377 mW
JG
1050 mV
8.4 mW/°C
672 mW
546 mW
210 mW
LP
775 mV
6.2 mW/°C
496 mW
403 mW
155 mW
recommended operating conditions
C-SUFFIX
I-SUFFIX
M-SUFFIX
MIN
MAX
MIN
MAX
MIN
MAX
Input voltage, VI
4
40
4
40
4
40
V
Operating free-air temperature, TA
0
70
– 40
85
– 55
125
°C
2
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
•
UNIT
TLE2425
PRECISION VIRTUAL GROUND
SLOS065D – MARCH 1991 – REVISED APRIL 2002
electrical characteristics at specified free-air temperature, VI = 5 V, IO = 0 (unless otherwise noted)
PARAMETER
Output voltage
MIN
TYP
MAX
25°C
2.48
2.5
2.52
Full range
2.47
Temperature coefficient of output voltage
Bias current
IO = 0
170
1.5
∆VI(PP) = 1 V
IO = 0 to – 10 mA
1.5
IO = 0 to 20 mA
∆t = 1000 h,
80
– 160
Full range
– 250
25°C
– 450
– 150
450
25°C
– 160
15
160
Full range
– 250
25°C
– 235
Noncumulative
25°C
Short-circuit output current (source current)
Output noise voltage, rms
f = 10 Hz to 10 kHz
Output voltage response to output current step
25°C
25°C
VO to 0.1%,,
IO = ± 10 mA
CL = 0
VO to 0.01%,,
IO = ± 10 mA
CL = 0
CL = 100 pF
Output voltage response to input voltage step
VI = 4.5 to 5.5 V,
VI = 4.5 to 5.5 V,
Output voltage turn
turn-on
on response
VI = 0 to 5 V,
VI = 0 to 5 V,
CL = 100 pF
VO to 0.1%
VO to 0.01%
VO to 0.1%
VO to 0.01%
250
250
65
7.5
30
55
– 30
– 50
100
µA
µV
µV/V
160
µV
µV
235
15
25°C
VO = 5 V
VO = 0
– 45
V
dB
25°C
Output impedance
Short-circuit output current (sink current)
20
25
25°C
IO = 0 to – 20 mA
IO = 0 to 10 mA
20
25
25°C
UNIT
ppm/°C
250
250
Full range
f = 120 Hz,
Long-term drift of output voltage
20
25°C
25°C
VI = 4 V to 40 V
Output voltage
g regulation
g
((sink current))‡
25°C
Full range
Input voltage regulation
Output voltage
g regulation
g
((source current))‡
2.53
Full range
VI = 4
4.5
5 V to 5
5.5
5V
Ripple rejection
TLE2425C
TA†
TEST CONDITIONS
ppm
22.5
mΩ
mA
µV
110
25°C
115
180
µs
180
25°C
25°C
12
30
125
210
µs
µs
† Full range is 0°C to 70°C.
‡ The listed values are not production tested.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
•
3
TLE2425
PRECISION VIRTUAL GROUND
SLOS065D – MARCH 1991 – REVISED APRIL 2002
electrical characteristics at specified free-air temperature, VI = 5 V, IO = 0 (unless otherwise noted)
PARAMETER
TEST CONDITIONS
Output voltage
Temperature coefficient of output voltage
Bias current
IO = 0
2.48
2.5
2.52
Full range
2.47
∆VI(PP) = 1 V
IO = 0 to – 10 mA
IO = 0 to 8 mA
IO = 0 to 20 mA
∆t = 1000 h,
Noncumulative
Output impedance
20
25°C
170
1.5
Short-circuit output current (source current)
VO = 5 V
VO = 0
Output noise voltage, rms
f = 10 Hz to 10 kHz
80
– 160
Full range
– 250
25°C
– 450
– 150
450
25°C
– 160
15
160
Full range
– 250
25°C
– 235
25°C
Output voltage response to output current step
VO to 0.01%,,
IO = ± 10 mA
CL = 0
CL = 100 pF
Output voltage response to input voltage step
VI = 4.5 to 5.5 V,
VI = 4.5 to 5.5 V,
Output voltage turn
turn-on
on response
VI = 0 to 5 V,
VI = 0 to 5 V,
CL = 100 pF
VO to 0.1%
VO to 0.01%
VO to 0.1%
VO to 0.01%
† Full range is – 40°C to 85°C.
‡ The listed values are not production tested.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
•
– 45
250
7.5
55
– 30
– 50
100
µV
µV/V
µV
µV
235
15
30
µA
160
250
65
V
dB
25°C
25°C
CL = 0
20
75
25°C
25°C
VO to 0.1%,,
IO = ± 10 mA
20
75
1.5
UNIT
ppm/°C
250
250
25°C
Short-circuit output current (sink current)
2.53
25°C
25°C
IO = 0 to – 20 mA
4
25°C
Full range
f = 120 Hz,
Long-term drift of output voltage
MAX
25°C
VI = 4 V to 40 V
Output voltage
g regulation
g
((sink current))‡
TYP
Full range
Input voltage regulation
Output voltage
g regulation
g
((source current))‡
MIN
Full range
VI = 4
4.5
5 V to 5
5.5
5V
Ripple rejection
TLE2425I
TA†
ppm
22.5
mΩ
mA
µV
110
25°C
115
180
µs
180
25°C
25°C
12
30
125
210
µs
µs
TLE2425
PRECISION VIRTUAL GROUND
SLOS065D – MARCH 1991 – REVISED APRIL 2002
electrical characteristics at specified free-air temperature, VI = 5 V, IO = 0 (unless otherwise noted)
PARAMETER
Output voltage
MIN
TYP
MAX
25°C
2.48
2.5
2.52
Full range
2.47
Temperature coefficient of output voltage
Bias current
IO = 0
170
1.5
80
– 160
Full range
– 250
25°C
– 450
– 150
450
25°C
– 160
15
160
Full range
– 250
25°C
– 235
Noncumulative
25°C
Short-circuit output current (source current)
Output noise voltage, rms
f = 10 Hz to 10 kHz
Output voltage response to output current step
25°C
25°C
VO to 0.1%,,
IO = ± 10 mA
CL = 0
VO to 0.01%,,
IO = ± 10 mA
CL = 0
CL = 100 pF
Output voltage response to input voltage step
VI = 4.5 to 5.5 V,
VI = 4.5 to 5.5 V,
Output voltage turn
turn-on
on response
VI = 0 to 5 V,
VI = 0 to 5 V,
CL = 100 pF
VO to 0.1%
VO to 0.01%
VO to 0.1%
VO to 0.01%
250
250
65
7.5
30
55
– 30
– 50
100
µA
µV
µV/V
160
µV
µV
235
15
25°C
VO = 5 V
VO = 0
– 45
V
dB
25°C
Output impedance
Short-circuit output current (sink current)
20
100
25°C
IO = 0 to – 20 mA
IO = 0 to 3 mA
20
100
25°C
IO = 0 to – 10 mA
IO = 0 to 20 mA
∆t = 1000 h,
1.5
UNIT
ppm/°C
250
250
Full range
∆VI(PP) = 1 V
f = 120 Hz,
Long-term drift of output voltage
20
25°C
25°C
VI = 4.5
4 5 V to 40 V
Output voltage
g regulation
g
((sink current))‡
25°C
Full range
Input voltage regulation
Output voltage
g regulation
g
((source current))‡
2.53
Full range
VI = 4
4.5
5 V to 5
5.5
5V
Ripple rejection
TLE2425M
TA†
TEST CONDITIONS
ppm
22.5
mΩ
mA
µV
110
25°C
115
180
µs
180
25°C
25°C
12
30
125
210
µs
µs
† Full range is – 55°C to 125°C.
‡ The listed values are not production tested.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
•
5
TLE2425
PRECISION VIRTUAL GROUND
SLOS065D – MARCH 1991 – REVISED APRIL 2002
TYPICAL CHARACTERISTICS
Table Of Graphs
FIGURE
Output voltage
Output voltage hysteresis
Input bias current
Distribution
1
vs Free-air temperature
2
vs Free-air temperature
3
vs Input voltage
4
vs Free-air temperature
5
Input voltage regulation
6
Ripple rejection
vs Frequency
Output voltage regulation
6
7
8
Output impedance
vs Frequency
9
Short-circuit output current
vs Free-air temperature
10
Spectral noise voltage density
vs Frequency
11
Wide-band noise voltage
vs Frequency
12
Output voltage change with current step
vs Time
13
Output voltage change with voltage step
vs Time
14
Output voltage power-up response
vs Time
15
Output current
vs Load capacitance
16
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
•
TLE2425
PRECISION VIRTUAL GROUND
SLOS065D – MARCH 1991 – REVISED APRIL 2002
TYPICAL CHARACTERISTICS†
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
DISTRIBUTION OF
OUTPUT VOLTAGE
24
VI = 5 V
TA = 25°C
2.53
100 Units Tested
From 1 Wafer Lot
VI = 5 V
IO = 0
2.52
VV)
O – Output Voltage – V
Percentage of Units – %
20
16
12
8
4
2.51
2.5
2.49
2.48
0
2.48
2.5
2.49
2.51
2.47
– 75
2.52
– 50
VO – Output Voltage – V
– 25
Figure 1
50
75
100
125
35
40
INPUT BIAS CURRENT
vs
INPUT VOLTAGE
4
250
VI = 5 V
Normalized to First 25°C VO
IO = 0
TA = 25°C
IIB
I IB – Input Bias Current – µ A
Output Voltage Hysteresis – mV
25
Figure 2
OUTPUT VOLTAGE HYSTERESIS
vs
FREE-AIR TEMPERATURE
2
0
TA – Free-Air Temperature – °C
Start Point
0
End Point
–2
–4
–6
200
150
100
50
–8
– 10
– 75
0
– 50
– 25
0
25
50
75
100
125
0
5
10
TA – Free-Air Temperature – °C
Figure 3
25
15
20
30
VI – Input Voltage – V
Figure 4
† Data at high and low temperatures are applicable within rated operating free-air temperature ranges of the various devices.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
•
7
TLE2425
PRECISION VIRTUAL GROUND
SLOS065D – MARCH 1991 – REVISED APRIL 2002
TYPICAL CHARACTERISTICS†
INPUT BIAS CURRENT
vs
FREE-AIR TEMPERATURE
172
INPUT VOLTAGE REGULATION
80
VI = 5 V
IO = 0
170
IO = 0
TA = 25°C
∆ VV)
O – Output Voltage Change – µV
IIB
I IB – Input Bias Current – µ A
168
166
164
162
160
158
156
154
152
150
– 75 – 50
60
40
20
0
– 20
– 25
0
25
50
75
100
TA – Free-Air Temperature – °C
125
0
Figure 5
OUTPUT VOLTAGE REGULATION
100
90
VI = 5 V
80
∆VV)
O – Output Voltage Change – µV
80
70
60
50
40
30
VI = 5 V
∆VI(PP) = 1 V
IO = 0
TA = 25°C
20
10
10
100
60
TA = – 40°C
TA = 0°C
40
TA = – 55°C
20
0
– 20
– 40
10 k
100 k
– 100
– 10 – 8
1M
TA = 125°C
– 60
– 80
1k
TA = 125°C
TA = 25°C
TA = 25°C
f – Frequency – Hz
Figure 7
TA = – 55°C
–6
–4 –2
0
2 4
6
IO – Output Current – mA
Figure 8
† Data at high and low temperatures are applicable within rated operating free-air temperature ranges of the various devices.
8
40
Figure 6
RIPPLE REJECTION
vs
FREQUENCY
Ripple Rejection – dB
30
10
20
VI – Input Voltage – V
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
•
8
10
TLE2425
PRECISION VIRTUAL GROUND
SLOS065D – MARCH 1991 – REVISED APRIL 2002
TYPICAL CHARACTERISTICS
OUTPUT IMPEDANCE
vs
FREQUENCY
SHORT-CIRCUIT OUTPUT CURRENT
vs
FREE-AIR TEMPERATURE
56
100
IO = 0
IIOS
OS – Short-Circuit Output Current – mA
VI = 5 V
TA = 25°C
z o – Output Impedance – Ω
10
IO = 10 mA
1
0.1
IO = – 10 mA
0.01
10
100
1k
10 k
100 k
1M
– IOS
Output Source, VO = 0
52
50
48
46
44
42
40
0.001
IOS
Output Sink, VO = 5 V
54
VI = 5 V
– 75 – 50
f – Frequency – Hz
75 100
0
25
50
– 25
TA – Free-Air Temperature – °C
Figure 9
Figure 10
WIDE-BAND NOISE VOLTAGE
vs
FREQUENCY
1400
80
1200
70
Wide-Band Noise Voltage – µV
V rms
Vn – Spectral Noise Voltage Density – nV/ Hz
SPECTRAL NOISE VOLTAGE DENSITY
vs
FREQUENCY
1000
800
600
400
200
VI = 5 V
TA = 25°C
0
1
10
125
100
1k
f – Frequency – Hz
10 k
VI = 5 V
TA = 25°C
1 Hz to Frequency Indicated
60
1 Pole Low Pass
50
40
30
20
2 Pole Low Pass
10
0
10
100 k
100
1k
10 k
100 k
f – Frequency – Hz
Figure 11
Figure 12
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
•
9
TLE2425
PRECISION VIRTUAL GROUND
SLOS065D – MARCH 1991 – REVISED APRIL 2002
TYPICAL CHARACTERISTICS
OUTPUT VOLTAGE RESPONSE
TO INPUT VOLTAGE STEP
vs
TIME
OUTPUT VOLTAGE RESPONSE
TO OUTPUT CURRENT STEP
vs
TIME
500
4
4
VI = 5 V
CL = 100 pF
TA = 25°C
3
0.1 %
2
1
∆V O – Change In Output Voltage – mV
∆V O – Change In Output Voltage – mV
1.5 V
0.01 %
0
VO Response
0.01 %
–1
–2
10 mA
–3
IO Step
0.1 %
0
– 10 mA
–4
150
300
450
600
750
t – Time – s
m
900
IO = 0
CL = 100 pF
TA = 25°C
1050
0.1 %
2
1
0
0.01 %
VO Response
–1
VI = 5.5 V
–2
0.1 %
–3
VI = 4.5 V
–4
VI Step
– 500
0
– 1.5 V
0
3
50
Figure 13
VI = 4.5 V
100
t – Time
- ms
200
150
Figure 14
STABILITY RANGE
OUTPUT VOLTAGE POWER-UP RESPONSE
vs
TIME
3
OUTPUT CURRENT
vs
LOAD CAPACITANCE
20
IO = 0
CL = 100 pF
TA = 25°C
0.1 %
15
Unstable
10
I O – Output Current – mA
VV)
O – Output Voltage – V
2
VI = 5 V
TA = 25°C
Output Voltage Response
1
0
5
5
0
–5
Stable
– 10
– 15
Input Voltage Step
0
0
10
t – Time
- ms
20
– 20
10 – 6 10 – 5 10 – 4 10 – 3 10 – 2 10 – 1 10 0
CL– Load Capacitance – F
130
m
Figure 15
10
Figure 16
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
•
10 1
10 2
TLE2425
PRECISION VIRTUAL GROUND
SLOS065D – MARCH 1991 – REVISED APRIL 2002
macromodel information
* TLE2425 OPERATIONAL AMPLIFIER “MACROMODEL” SUBCIRCUIT
* CREATED USING PARTS RELEASE 4.03 ON 08/21/90 AT 13:51
* REV (N/A)
SUPPLY VOLTAGE: 5 V
* CONNECTIONS: INPUT
*
| COMMON
*
| | OUTPUT
*
| | |
.SUBCKT TLE2425 3 4 5
*
*
+
OPAMP
C1
C2
C3
CPSR
DCM+
DCM–
DC
DE
DLN
DLP
DP
ECMR
EGND
EPSR
ENSE
FB
–10E6
GA
GCM
GPSR
GRC1
GRC2
GRE1
GRE2
HLIM
HCMR
IRP
IEE
IIO
I1
Q1
Q2
R2
RCM
REE
RN1
RN2
SECTION
11 12 21.66E – 12
6 7 30.00E – 12
87 0 10.64E – 9
85 86 15.9E – 9
81 82 DX
83 81 DX
5 53 DX
54 5 DX
92 90 DX
90 91 DX
4 3 DX
84 99 (2,99) 1
99 0 POLY(2)
(3,0) (4,0) 0 .5 .5
85 0 POLY(1)
(3,4) –16.22E–6 3.24E–6
89 2 POLY(1)
(88,0) 120E–6 1
7 99 POLY(6)
VB VC VE VLP VLN VPSR
O
74E6
6 0 11 12 320.4E–6
0 6 10 99 1.013E–9
85 86 (85,86)
100E–6
4 11 (4,11) 3.204E–4
4 12 (4,12) 3.204E–4
13 10 (13,10)
1.038E–3
14 10 (14,10)
1.038E–3
90 0 VLIM
1K
80 1 POLY(2)
VCM+
VCM–
0 1E2 1E2
3 4 146E–6
3 10 DC 24.05E–6
2 0 .2E–9
88 0 1E–21
11 89 13 QX
12 80 14 QX
6 9 100.0E3
84 81 1K
10 99 8.316E6
87 0 2.55E8
87 88 11.67E3
•
74.8E6 –10E6 10E6
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
•
10E6
11
TLE2425
PRECISION VIRTUAL GROUND
SLOS065D – MARCH 1991 – REVISED APRIL 2002
macromodel information (continued)
RO1
8 5 63
RO2
7 99 62
VCM+
82 99 1.0
VCM–
83 99 –2.3
VB
9 0 DC 0
VC
3 53 DC 1.400
VE
54 4 DC 1.400
VLIM
7 8 DC 0
VLP
91 0 DC 30
VLN
0 92 DC 30
VPSR
0 86 DC 0
RFB
5 2 1K
RIN
30 1 1K
RCOM
34 4 .1
*REGULATOR SECTION
RG1
30 0 20MEG
RG2
30 31 .2
RG3
31 35 400K
RG4
35 34 411K
RG5
31 36 25MEG
HREG
31 32 POLY(2)
VPSET VNSET 0 1E2 1E2
VREG
32 33 DC 0V
EREG
33 34 POLY(1)
(36,34)
1.23 1
VADJ
36 34 1.27V
HPSET 37 0 VREG
1.030E3
VPSET 38 0 DC 20V
HNSET 39 0 VREG
6.11E5
VNSET 40 0 DC –20V
DSUB
4 34 DX
DPOS
37 38 DX
DNNEG 40 39 DX
.MODEL DX D(IS=800.0E–18)
.MODEL QX PNP(IS=800.0E–18 BF=480)
.ENDS
12
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
•
TLE2425
PRECISION VIRTUAL GROUND
SLOS065D – MARCH 1991 – REVISED APRIL 2002
MECHANICAL INFORMATION
D (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
0.050 (1,27)
0.020 (0,51)
0.014 (0,35)
14
0.010 (0,25) M
8
0.008 (0,20) NOM
0.244 (6,20)
0.228 (5,80)
0.157 (4,00)
0.150 (3,81)
Gage Plane
0.010 (0,25)
1
7
0°– 8°
A
0.044 (1,12)
0.016 (0,40)
Seating Plane
0.069 (1,75) MAX
0.010 (0,25)
0.004 (0,10)
PINS **
0.004 (0,10)
8
14
16
A MAX
0.197
(5,00)
0.344
(8,75)
0.394
(10,00)
A MIN
0.189
(4,80)
0.337
(8,55)
0.386
(9,80)
DIM
4040047 / D 10/96
NOTES: A.
B.
C.
D.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
Falls within JEDEC MS-012
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
•
13
TLE2425
PRECISION VIRTUAL GROUND
SLOS065D – MARCH 1991 – REVISED APRIL 2002
MECHANICAL INFORMATION
JG (R-GDIP-T8)
CERAMIC DUAL-IN-LINE PACKAGE
0.400 (10,20)
0.355 (9,00)
8
5
0.280 (7,11)
0.245 (6,22)
1
4
0.065 (1,65)
0.045 (1,14)
0.310 (7,87)
0.290 (7,37)
0.020 (0,51) MIN
0.200 (5,08) MAX
Seating Plane
0.130 (3,30) MIN
0.063 (1,60)
0.015 (0,38)
0.100 (2,54)
0°–15°
0.023 (0,58)
0.015 (0,38)
0.014 (0,36)
0.008 (0,20)
4040107/C 08/96
NOTES: A.
B.
C.
D.
E.
14
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
This package can be hermetically sealed with a ceramic lid using glass frit.
Index point is provided on cap for terminal identification only on press ceramic glass frit seal only.
Falls within MIL-STD-1835 GDIP1-T8
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
•
TLE2425
PRECISION VIRTUAL GROUND
SLOS065D – MARCH 1991 – REVISED APRIL 2002
MECHANICAL INFORMATION
LP (O-PBCY-W3)
PLASTIC CYLINDRICAL PACKAGE
0.022 (0,56)
Wide
0.016 (0,41)
0.016 (0,41)
Thick
0.014 (0,35)
0.165 (4,19)
0.125 (3,17)
3 Leads
0.105 (2,67)
0.080 (2,03)
Seating Plane
0.055 (1,40)
0.045 (1,14)
0.105 (2,67)
0.095 (2,41)
0.050 (1,27)
(see Note C)
0.135 (3,43) MIN
3
0.205 (5,21)
DIA
0.175 (4,44)
2
1
0.210 (5,34)
0.170 (4,32)
0.500 (12,70) MIN
0.105 (2,67)
0.080 (2,03)
4040001 / B 01/95
NOTES: A.
B.
C.
D.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
Lead dimensions are not controlled within this area.
Falls within JEDEC TO-226AA (TO-226AA replaces TO-92)
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251–1443
•
15
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third–party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2002, Texas Instruments Incorporated