TUSB2046 4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999 D D D D D D D D D D D D D D D D VF PACKAGE (TOP VIEW) SUSPND TSTMODE XTAL1 XTAL2 GND TSTPLL EXTMEM VCC D Universal Serial Bus (USB) Version 1.1 Compliant 32-Pin TQFP Package With a 0.8 mm Pin Pitch 3.3-V Low Power ASIC Logic Integrated USB Transceivers State Machine Implementation Requires No DP0 Firmware Programming DM0 One Upstream Port and Four Downstream VCC Ports RESET All Downstream Ports Support Full-Speed EECLK and Low-Speed Operations EEDATA/GANGED Two Power Source Modes GND – Self-Powered Mode BUSPWR – Bus-Powered Mode Power Switching and Over-current Reporting is Provided Ganged or Per Port Supports Suspend and Resume Operations Supports Programmable Vendor ID and Product ID With External Serial EEPROM 3-State EEPROM Interface Allows EEPROM Sharing Push-Pull Outputs for PWRON Eliminate the Need for External Pullup Resistors Noise Filtering on OVRCUR Provides Immunity to Voltage Spikes Package Pinout Allows 2-Layer PCB Low EMI Emission Achieved by a 6-MHz Crystal Input Migrated From Proven TUSB2040 Hub Lower Cost Than the TUSB2040 Hub 32 31 30 29 28 27 26 25 1 24 2 23 3 22 4 21 5 20 6 19 7 18 17 8 DP4 DM4 OVRCUR4 PWRON4 DP3 DM3 OVRCUR3 PWRON3 9 10 11 12 13 14 15 16 PWRON1 OVRCUR1 DM1 DP1 PWRON2 OVRCUR2 DM2 DP2 D description The TUSB2046 is a 3.3 V CMOS hub device that provides one upstream port and four downstream ports in compliance with the 1.1 Universal Serial Bus (USB) specification. Because this device is implemented with a digital state machine instead of a microcontroller, no firmware programming is required. Fully compliant USB transceivers are integrated into the ASIC for all upstream and downstream ports. The downstream ports support both full-speed and low-speed devices by automatically setting the slew rate according to the speed of the device attached to the ports. The configuration of the BUSPWR pin selects either the bus-powered or the self-powered mode. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 1999, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 TUSB2046 4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999 description (continued) Configuring the GANGED input determines the power switching and over-current detection modes for the downstream ports. External power management devices such as the TPS2044 are required to control the 5-V source to the downstream ports according to the corresponding values of the PWRON pin. Upon detecting any over-current conditions, the power management device sets the corresponding OVRCUR pin of the TUSB2046 to a logic low. If GANGED is high, all PWRON outputs switch together and if any OVRCUR is activated, all ports transition to power off state. If GANGED is low, the PWRON outputs and OVRCUR inputs operate on a per port basis. Low EMI emission is achieved because the TUSB2046 is able to utilize a 6 MHz crystal input. Connect the crystal as shown in Figure 7. An internal PLL then generates the 48 MHz clock used to sample data from the upstream port and to synchronize the 12 MHz used for the USB clock. If low power suspend and resume are desired, a passive crystal or resonator must be used. However, a 6-MHz oscillator may be used by connecting the output to the XTAL1 terminal and leaving the XTAL2 terminal open. The oscillator TTL output should not exceed 3.6 V. The EXTMEM pin enables or disables the optional EEPROM interface. When the EXTMEM pin is high, the product ID (PID) displayed during enumeration is General-Purpose USB Hub. For this default, pin 5 is disabled and pin 6 functions as the GANGED input pin. If custom PID and Vendor ID (VID) descriptors are desired, the EXTMEM pin must be low (EXTMEM = 0). For this configuration, pin 5 and pin 6 function as the EEPROM interface with pin 5 and pin 6 functioning as the EECLK and EEDATA, respectively. See Table 1 for a description of the EEPROM memory map. Other useful features of the TUSB2046 include a package with a 0.8 mm pin pitch for easy PCB routing and assembly, push-pull outputs for the PWRON pins eliminate the need for pullup resistors required by traditional open collector I/Os, and OVRCUR pins have noise filtering for increased immunity to voltage spikes. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TUSB2046 4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999 functional block diagram DP0 1 DM0 2 USB Transceiver 32 27 30 29 Suspend / Resume Logic and Frame Timer Hub Repeater OSC/PLL SUSPND TSTPLL XTAL1 XTAL2 SIE 4 RESET 26 SIE Interface Logic 6 Serial EEPROM Interface 5 EXTMEM EEDATA/GANGED EECLK Port 1 Logic Port 2 Logic Hub / Device Command Decoder Port 3 Logic 8 Port 4 Logic USB Transceiver 24 23 USB Transceiver 20 19 USB Transceiver 16 15 USB Transceiver 12 Hub Power Logic 10, 14, 18, 22 11 9, 13, 17, 21 DP4 DM4 DP3 DM3 DP2 DM2 DP1 DM1 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 BUSPWR OVRCUR1 – OVRCUR4 PWRON1 – PWRON4 3 TUSB2046 4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999 Terminal Functions TERMINAL NAME NO. I/O DESCRIPTION Power source indicator. BUSPWR is an active high input that indicates whether the downstream ports source their power from the USB cable or a local power supply. For the bus-power mode, this pin should be pulled to 3.3 V, and for the self-powered mode, this pin should be pulled low. Input must not change dynamically during operation. BUSPWR 8 I DM0 2 I/O Root port USB differential data minus. DM0 paired with DP0 constitutes the upstream USB port. 11, 15, 19, 23 I/O USB differential data minus. DM1 – DM4 paired with DP1 – DP4 support up to four downstream USB ports. DM1 – DM4 DP0 1 I/O Root port USB differential data plus. DP0 paired with DM0 constitutes the upstream USB port. 12, 16, 20, 24 I/O USB differential data plus. DP1 – DP4 paired with DM1 – DM4 support up to four downstream USB ports. EECLK 5 O EEPROM serial clock. When EXTMEM is high, the EEPROM interace is disabled. The EECLK pin is disabled and should be left floating (unconnected). When EXTMEM is low, EECLK acts as a 3-state serial clock output to the EEPROM with a 100 µA internal pulldown. EEDATA/ GANGED 6 I/O EEPROM serial data/power management mode indicator. When EXTMEM is high, EEDATA/GANGED selects between gang or per-port power over-current detection for the downstream ports. When EXTMEM is low, EEDATA/GANGED acts as a serial data I/O for the EEPROM and is internally pulled down with a 100 µA pulldown. This standard TTL input must not change dynamically during operation. EXTMEM 26 I EEPROM read enable. When EXTMEM is high, the serial EEPROM interface of the device is disabled. When EXTMEM is low, terminals 5 and 6 are configured as the clock and data pins of the serial EEPROM interface, respectively. DP1 – DP4 GND 7, 28 Ground. GND terminals must be tied to ground for proper operation. OVRCUR1 – OVRCUR4 10, 14, 18, 22 I Over-current input. OVRCUR1 – OVRCUR4 are active low. For per-port over current detection, one over-current input is available for each of the four downstream ports. In the ganged mode, any OVRCUR input may be used and all OVRCUR pins should be tied together. OVRCUR pins are active low inputs with noise filtering logic. PWRON1 – PWRON4 9, 13, 17, 21 O Power-on/-off control signals. PWRON1 – PWRON4 are active low, push-pull outputs. Push-pull outputs eliminate the pullup resistors which open-drain outputs require. However, the external power switches that connect to these pins must be able to operate with 3.3-V inputs because these outputs cannot drive 5-V signals. RESET 4 I Reset. RESET is an active low TTL input with hysteresis and must be asserted at power up. When RESET is asserted, all logic is initialized. SUSPND 32 O Suspend status. SUSPND is an active high output available for external logic power down operations. During the suspend mode, SUSPND is high. SUSPND is low for normal operation. TSTMODE 31 I Test pin. TSTMODE is used as a test pin during production testing. This pin must be tied to ground for normal operation. TSTPLL 27 I/O Test pin. TSTPLL is used as a test pin during production testing. This pin must be tied to ground for normal operation VCC 3, 25 3.3-V supply voltage XTAL1 30 I Crystal 1. XTAL1 is a 6-MHz crystal input with 50% duty cycle. An internal PLL generates the 48-MHz and 12-MHz clocks used internally by the ASIC logic. XTAL2 29 O Crystal 2. XTAL2 is a 6-MHz crystal output. This terminal should be left open when using an oscillator. 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TUSB2046 4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 3.6 V Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to VCC + 0.5 V Output voltage range, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Input clamp current, IIK, (VI < 0 V or VI > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Output clamp current, IOK, (VO < 0 V or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltage levels are with respect to GND. recommended operating conditions MIN NOM Supply voltage, VCC 3 3.3 MAX UNIT 3.6 Input voltage, TTL/LVCMOS, VI 0 V VCC VCC V Output voltage, TTL/LVCMOS, VO 0 High-level input voltage, signal-ended receiver, VIH(REC) 2 VCC 0.8 V High-level input voltage, TTL/LVCMOS, VIH(TTL) 2 V Low-level input voltage, TTL/LVCMOS, VIL(TTL) 0 VCC 0.8 Low-level input voltage, signal-ended receiver, VIL(REC) V V V 70 °C 22 (5%) Ω Operating (dc differential driver) high speed mode, f(OPRH) 12 Mb/s Operating (dc differential driver) low speed mode, f(OPRL) 1.5 Mb/s Operating free-air temperature, TA 0 External series, differential driver resistor, R(DRV) 22 (–5%) Common mode, input range, differential receiver, V(ICR) 0.8 2.5 V Input transition times, tt, TTL/LVCMOS 0 25 ns Junction temperature range, TJ 0 115 °C POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 TUSB2046 4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999 electrical characteristics over recommended ranges of operating free-air temperature and supply voltage (unless otherwise noted) PARAMETER TEST CONDITIONS TTL/LVCMOS VOH High-level output voltage USB data lines TTL /LVCMOS VOL Low-level output voltage Positive input threshold voltage VIT IT– Negative input threshold voltage Negative-input IOH = –4 mA R(DRV) = 15 kΩ, to GND VCC – 0.5 2.8 IOH = – 12 mA (without R(DRV)) IOL = 4 mA VCC – 0.5 Single-ended 0.5 0.3 IOL = 12 mA (without R(DRV)) 0.5 0.8 V ≤ VICR ≤ 2.5 V TTL /LVCMOS Input hysteresis† (VT+ – VT–) Single-ended TTL /LVCMOS V 1.8 V 1.8 V 0.8 0.8 V ≤ VICR ≤ 2.5 V UNIT V R(DRV) = 1.5 k Ω to 3.6 V V 1 V 0.3 0.7 V Single-ended 0.8 V ≤ VICR ≤ 2.5 V 500 mV TTL/LVCMOS V = VCC or GND‡ ± 10 µA USB data lines 0 V ≤ VO ≤ VCC ± 10 µA –1 µA 1 µA 19.9 Ω 300 IOZ High impedance output current High-impedance IIL IIH Low-level input current TTL/LVCMOS High-level input current TTL/LVCMOS VI = GND VI = VCC zo(DRV) Driver output impedance USB data lines Static VOH or VOL 7.1 VID Differential input voltage USB data lines 0.8 V ≤ VICR ≤ 2.5 V 0.2 ICC MAX TTL /LVCMOS VIT IT+ Vh hys USB data lines MIN V Normal operation Input supply current Suspend mode 40 mA 1 µA † Applies for input buffers with hysteresis ‡ Applies for open drain buffers differential driver switching characteristics over recommended ranges of operating free-air temperature and supply voltage, CL = 50 pF (unless otherwise noted) full speed mode PARAMETER tr tf t(RFM VO(CRS) TEST CONDITIONS Transition rise time for DP or DM See Figure 1 and Figure 2 Transition fall time for DP or DM Rise/fall time matching§ See Figure 1 and Figure 2 (tr/tf) × 100 Signal crossover output voltage§ MIN MAX 4 20 UNIT ns ns 4 20 90% 110% 1.3 2.0 MIN MAX UNIT 75 300 ns ns V § Charicterized only. Limits are approved by design and are not production tested. low speed mode PARAMETER TEST CONDITIONS tr tf Transition rise time for DP or DM§ Transition fall time for DP or DM§ CL = 200 pF to 600 pF, See Figure 1 and Figure 2 CL = 200 pF to 600 pF, See Figure 1 and Figure 2 t(RFM) VO(CRS) Rise/fall time matching§ (tr/tf) × 100 CL = 200 pF to 600 pF Signal crossover output voltage§ § Charicterized only. Limits are approved by design and are not production tested. 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 75 300 80% 120% 1.3 2.0 V TUSB2046 4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999 Characterization measurement point DP V(TERM) = VCC 22 Ω Full 15 kΩ DM 1.5 kΩ CL 22 Ω Low 15 kΩ CL Figure 1. Differential Driver Switching Load tf DM 90% 10% 90% 10% DP tf 90% 10% VOH 90% 10% tr VOL tr NOTE: The tr/tf ratio is measured as tr(DP)/tf(DM) and tr(DM)/tf(DP) at each crossover point. Figure 2. Differential Driver Timing Waveforms V ID – Differential Receiver Input Sensitivity – V 1.5 1.3 1 0.5 0.2 0 0 1 2 3 3.6 0.8 2.5 VICR – Common Mode Input Range – V 4 Figure 3. Differential Receiver Input Sensitivity vs Common Mode Input Range Vhys Logic high VCC VIH VIT+ VIT– VIL Logic low 0V Figure 4. Single-Ended Receiver Input Signal Parameter Definitions POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 TUSB2046 4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999 APPLICATION INFORMATION A major advantage of USB is the ability to connect 127 functions configured in up to six logical layers (tiers) to a single personal computer (see Figure 5). PC With Root Hub Monitor With 4-Port Hub (Self-Powered) Keyboard With 4-Port Hub (Bus-Powered) Left Speaker Mouse Modem Telephone Right Speaker Printer With 4-Port Hub (Self-Powered) Scanner Digital Scanner Figure 5. USB Tiered Configuration Example Another advantage of USB is that all peripherals are connected using a standardized four-wire cable that provides both communication and power distribution. The power configurations are bus-powered and self-powered modes. The maximum current that may be drawn from the USB 5-V line during power up is 100 mA. For the bus-powered mode, a hub can draw a maximum of 500 mA from the 5-V line of the USB cable. A bus-powered hub must always be connected downstream to a self-powered hub unless it is the only hub connected to the PC and there are no high-powered functions connected downstream. In the self-powered mode, the hub is connected to an external power supply and can supply up to 500 mA to each downstream port. High-powered functions may draw a maximum of 500 mA from each downstream port and may only be connected downstream to self-powered hubs. Per the USB specification, in the bus-powered mode, each downstream port can provide a maximum of 100 mA of current, and in the self-powered mode, each downstream port can provide a maximum of 500 mA of current. Both bus-powered and self-powered hubs require over-current protection for all downstream ports. The two types of protection are individual port management (individual port basis) or ganged port management (multiple port basis). Individual port management requires power management devices for each individual downstream port, but adds robustness to the USB system because, in the event of an over-current condition, the USB host only powers down the port that has the condition. The ganged configuration uses fewer power management devices and thus has lower system costs, but in the event of an over-current condition on any of the downstream ports, all the ganged ports are disabled by the USB host. Using a combination of the BUSPWR and EEDATA/GANGED inputs, the TUSB2046 supports four modes of power management: bus-powered hub with either individual port power management or ganged port power management, and the self-powered hub with either individual port power management or ganged port power management. Texas Instruments supplies the complete hub solution because we offer this TUSB2046, the TUSB2077 (7–port) and the TUSB2140B (4-port with I2C) hubs along with the power management chips needed to implement a fully USB Specification 1.1 compliant system. 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TUSB2046 4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999 APPLICATION INFORMATION USB design notes The following sections provide block diagram examples of how to implement the TUSB2046 device.Note, even though no resistors are shown, pullup, pulldown and series resistors must still be used to properly implement this device. Figure 1 shows a few resistors that must be used for the USB lines, and for a general reference design, one is available on the TI USB web site at http://www.ti.com/sc/usb. Figure 6 is a block diagram example of how to connect the external EEPROM if a custom product ID and vendor ID are desired. Figure 7 is an example of how to generate the 6-MHz clock signal. Figure 8 shows the EEPROM read operation timing diagram. Figures 9, 10, and 11 illustrate how to connect the TUSB2046 device for different power source and port power management combinations. TUSB2046 USB Hub 6-MHz Clock Signal Bus or Local Power 5 V GND 30 XTAL1 3, 25 29 VCC XTAL2 Regulator 3.3 V 4 System Power-On Reset RESET GND 7, 28 26 EXTMEM 1 2 EEPROM 6 D ORG 6 EEDATA 1 kΩ 8 5 VCC Q VSS C 5 4 4 11, 15, 19, 23 4 10, 14, 18, 22 4 DM1 – DM4 DM0 3 12, 16, 20, 24 DP1 – DP4 DP0 OVRCUR1 – OVRCUR4 EECLK PWRON1 – PWRON4 Power Switching 9, 13, 17, 21 4 GND USB Data lines and Power to Downstream Ports Vbus 2 S 1 Figure 6. Typical Application of the TUSB2046 USB Hub CL XTAL1 XTAL2 Rd C1 C2 NOTE A: Figure 7 assumes a 6 MHz fundamental crystal that is parallel loaded. The component values of C1, C2 and Rd were determined using a crystal from Fox Electronics – part number HC49U–6.00MHz30\50\0 ±70\20 which means ±30 ppm at 25°C and 50 ppm from 0°C to 70°C. The characteristics for the crystal are load capacitance (CL) of 20 pF, maximum shunt capacitance (Co) of 7 pF and the maximum ESR of 50 Ω. In order to insure enough negative resistance, use C1 = C2 = 27 pF. The resistor Rd is used to trim the gain, and Rd = 1.5 kΩ is recommended. Figure 7. Crystal Tuning Circuit POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 TUSB2046 4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999 APPLICATION INFORMATION programming the EEPROM An SGS Thompson M93C46 EEPROM or equivalent is used for storing the programmable VID and PID. When the EEPROM interface is enabled (EXTMEM = 0), the EECLK and EEDATA are internally pulled down (100 µA) inside the TUSB2046. The internal pulldowns are disabled when the EEPROM interface is disabled (EXTMEM = 1). The EEPROM is programmed with the three 16-bit locations as shown in Table 1. Connecting pin 6 of the EEPROM high (ORG = 1) organizes the EEPROM memory into 64×16 bit words. Table 1. EEPROM Memory Map ADDRESS D15 D14 D13 D12–D8 D7–D0 00000 0 GANGED 00000 00000 00000000 00001 VID High-byte VID Low-byte 00010 PID High-byte PID Low-byte XXXXXXXX The D and Q signals of the EEPROM must be tied together using a 1 kΩ resistor with the common I/O operations forming a single-wire bus. After system power-on reset, the TUSB2046 performs a one-time access read operation from the EEPROM if the EXTMEM pin is pulled low and the chip select(s) of the EEPROM is connected to the system power-on reset. Initially, the EEDATA pin will be driven by the TUSB2046 to send a start bit (1) which is followed by the read instruction (10) and the starting-word address (00000). Once the read instruction is received, the instruction and address are decoded by the EEPROM, which then sends the data to the output shift register. At this point, the hub stops driving the EEDATA pin and the EEPROM starts driving. A dummy (0) bit is then output and the first three 16-bit words in the EEPROM are output with the most significant bit (MSB) first. The output data changes are triggered by the rising edge of the clock provided by the TUSB2046 on the EECLK pin. The SGS-Thompson M936C46 EEPROM is recommended because it advances to the next memory location by automatically incrementing the address internally. Any EEPROM used must have the automatic internal address advance function. After reading the three words of data from the EEPROM, the TUSB2046 puts the EEPROM interface into a high-impedance condition (pulled down internally) to allow other logic to share the EEPROM. The EEPROM read operation is summarized in Figure 8. For more details on EEPROM operation, refer to SGS-Thompson Microelectronics M93C46 Serial Microwire Bus EEPROM data sheet. 10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 D C S Start A5 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 Other Address Bits A1 6 Bit Address (000000) A0 Dummy Bit MSB of The First Word D15 Other LSB of Data Bits Third Word D0 EEPROM Driving Data Line D14 48 Data Bits Figure 8. EEPROM Read Operation Timing Diagram Hub Driving Data Line Read OP Code(10) MSB of Fourth Word XX Don’t Care 3-Stated With Internal Pulldown TUSB2046 4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999 11 TUSB2046 4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999 APPLICATION INFORMATION bus-powered hub, ganged port power management When used in bus-powered mode, the TUSB2046 supports up to four downstream ports by controlling a TPS2041 device which is capable of supplying 100 mA of current to each downstream port. Bus-powered hubs must implement power switching to ensure current demand is held below 100 mA when the hub is hot-plugged into the system. Utliizing the TPS2041 for ganged power management provides over-current protection for the downstream ports. The SN75240 transient suppressors reduce inrush current and voltage spikes on the data lines. The OVRCUR signals should be tied together for a ganged operation. 3.3 V TUSB2046 BUSPWR 3.3 V EEDATA/GANGED Upstream Port DP1 DP0 D+ D– DM0 SN75240† A C B D 4.7 µF 0.1 µF GND DM1 D+ 15 kΩ Ferrite Beads A C B D 15 kΩ D– GND SN75240† DP2 5V DM2 3.3 V LDO§ 5V Downstream Ports 1.5 kΩ 15 kΩ 5V 100 µF‡ 15 kΩ 3.3 V 4.7 µF VCC GND D+ D– DP3 DM3 XTAL1 6-MHz Clock Signal Ferrite Beads GND 15 kΩ 15 kΩ A C B D 5V SN75240† DP4 100 µF‡ DM4 15 kΩ XTAL2 D+ 15 kΩ 3.3 V PWRON1 EN PWRON2 System Power-On Reset RESET D– TPS2041† EXTMEM Ferrite Beads GND IN IN 1 µF 5V PWRON3 100 µF‡ PWRON4 OUT OUT OUT GND OVRCUR1 OC D+ Ferrite Beads OVRCUR2 D– GND OVRCUR3 OVRCUR4 5V 100 µF‡ † TPS2041 and SN75240 are Texas Instruments devices. ‡ 120 µF per hub is the minimum required per the USB specification, version 1.1. However, TI recommends a 100 µF low ESR tantulum capacitor per port for immunity to voltage droop. § LDO is a 5 V to 3.3 V voltage regulator Figure 9. TUSB2046 Bus-Powered Hub, Ganged Port Power Management Application 12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TUSB2046 4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999 APPLICATION INFORMATION self-powered hub, ganged port power management The TUSB2046 can also be implemented for ganged port power management in a self-powered configuration. The implementation is very similar to the bus-powered example with the exception that a self-powered port supplies 500 mA of current to each downstream port. The over-current protection can be provided by a TPS2044 quad device or a TPS2024 single power switch. TUSB2046 3.3 V EEDATA/GANGED Upstream Port 1.5 kΩ DM0 SN75240† Downstream Ports BUSPWR DP0 D+ D– 3.3 V DP1 D+ D– DM1 A C B D 5V 3.3 V LDO§ 4.7 µF 0.1 µF GND 4.7 µF VCC DM2 GND Ferrite Beads GND 15 kΩ SN75240† DP2 5V 3.3 V 15 kΩ A C B D 5V 15 kΩ 100 µF‡ 15 kΩ D+ DP3 D– DM3 15 kΩ XTAL1 6-MHz Clock Signal Ferrite Beads A C B D 15 kΩ XTAL2 SN75240† DP4 DM4 GND 15 kΩ 5V 100 µF‡ 15 kΩ TPS2044† PWRON1 3.3 V System Power-On Reset EXTMEM RESET PWRON2 EN1 EN2 PWRON3 EN3 PWRON4 EN4 OVRCUR1 OVRCUR2 OC1 OC2 OVRCUR3 OC3 OVRCUR4 OC4 D+ IN1 D– Ferrite Beads IN2 GND 0.1 µF 5V GND 100 µF‡ D+ D– OUT1 OUT2 Ferrite Beads GND OUT3 OUT4 5V 100 µF‡ 5 V Board Power † TPS2044, TPS2042, and SN75240 are Texas Instruments devices. Supply The TPS2024 can be substituted for the TPS2044. ‡ 120 µF per hub is the minimum required per the USB specification, version 1.1. However, TI recommends a 100 µF low ESR tantulum capacitor per port for immunity to voltage droop. § LDO is a 5 V to 3.3 V voltage regulator Figure 10. TUSB2046 Self-Powered Hub, Ganged Port Power Management Application POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 13 TUSB2046 4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999 APPLICATION INFORMATION self-powered hub, individual port power management In a self-powered configuration, the TUSB2046 can be implemented for individual port-power management when used with the TPS2044 because it is capable of supplying 500 mA of current to each downstream port and can provide current limiting on a per port basis. When the hub detects a fault on a downstream port, power is removed from only the port with the fault and the remaining ports continue to operate normally. Self-powered hubs are required to implement over-current protection and report overcurrent conditions. The SN75240 transient suppressors reduce inrush current and voltage spikes on the data lines. TUSB2046 Downstream Ports 3.3 V Upstream Port DM0 SN75240† D– EEDATA/GANGED 3.3 V LDO§ 4.7 µF 0.1 µF GND 5V 3.3 V GND 15 kΩ SN75240† DP2 DM2 15 kΩ A C B D BUSPWR A C B D 5V D+ DM1 DP0 D+ D– DP1 1.5 kΩ 5V 100 µF‡ 15 kΩ 15 kΩ 4.7 µF VCC D+ DP3 GND DM3 D– 15 kΩ 15 kΩ A C B D GND SN75240† 5V DP4 DM4 100 µF‡ 15 kΩ XTAL1 6-MHz Clock Signal 15 kΩ TPS2044† XTAL2 3.3 V EXTMEM PWRON1 EN1 D+ PWRON2 EN2 D– PWRON3 EN3 PWRON4 EN4 GND OUT1 5V OUT2 System Power-On Reset OUT3 RESET 100 µF‡ OUT4 GND OVRCUR1 OC1 IN1 OVRCUR2 OC2 IN2 OVRCUR3 OC3 OVRCUR4 OC4 D+ D– GND 0.1 µF 5V 100 µF‡ 5-V Board Power † TPS2042 and SN75240 are Texas Instruments devices. Two TPS2042 devices can be substituted for Supply the TPS2044. ‡ 120 µF per hub is the minimum required per the USB specification, version 1.1. However, TI recommends a 100 µF low ESR tantulum capacitor per port for immunity to voltage droop. § LDO is a 5 V to 3.3 V voltage regulator Figure 11. TUSB2046 Self-Powered Hub, Individual Port-Power Management Application 14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TUSB2046 4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE SLLS330A – FEBRUARY 1999 – REVISED AUGUST 1999 MECHANICAL DATA VF (S-PQFP-G32) PLASTIC QUAD FLATPACK 0,45 0,30 0,80 24 0,22 M 17 25 16 32 9 0,13 NOM 1 8 5,60 TYP 7,20 SQ 6,80 9,20 SQ 8,80 Gage Plane 0,25 0,05 MIN 1,45 1,35 Seating Plane 1,60 MAX 0°– 7° 0,75 0,45 0,10 4040172 / C 10/96 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Falls within JEDEC MS-026 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 15 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1999, Texas Instruments Incorporated