EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P GENERAL DESCRIPTION EM73983 is an advanced single chip CMOS 4-bit micro-controller. It contains 16K-byte ROM, 500-nibble RAM, 4-bit ALU, 13-level subroutine nesting, 22-stage time base, two 12-bit timer/counters for the kernel function. EM73983 also equipped with 6 interrupt sources, 3 I/O ports (including 1 input port and 2 bidirection ports), LCD display (40x8), built-in sound generator and speech synthesizer. It's low power consumption and high speedfeature are further strengten with DUAL, SLOW, IDLE and STOP operation mode for optimized power saving. FEATURES • Operation voltage • Clock source • • • • • • • • • • • • • • • • : 2.2V to 4.8V. : Dual clock system. Low-frequency oscillator is Crystal or RC oscillator (32K Hz, connect a external resistor) by mask option and high-frequency oscillator is a built-in internal oscillator (4.6 MHz). Instruction set : 107 powerful instructions. Instruction cycle time : 1.7µs for 4.6M Hz (high speed clock) . 244µs for 32768 Hz (low speed clock). ROM capacity : 16K x 8 bits. RAM capacity : 500 x 4 bits. Input port : 1 port (P0.0-P0.3), IDLE/STOP releasing function is available by mask option. (each input pin has a pull-up and pull-down resistor available by mask option). Bidrection port : 2 ports (P4, P8). IDLE/STOP release function for P8(0..3) is available by mask option. Built-in watch-dog-timer counter : It is available by mask option. 12-bit timer/counter : Two 12-bit timer/counters are programmable for timer, event counter and pulse width measurement mode. Built-in time base counter : 22 stages. Subroutine nesting : Up to 13 levels. Interrupt : External interrupt . . . . . . 2 input interrupt sources. Internal interrupt . . . . . . 2 timer overflow interrupts, 1 time base interrupt. 1 speech interrupt. LCD driver : 40x8 dots,1 /8 duty, 1/5 bias with voltage multiplier. Sound effect : Tone generator and random generator. Speech synthesizer : 160K speech data ROM (use as 160K nibbles data ROM). Power saving function : SLOW, IDLE, STOP operation modes. Package type : Chip form 77 pins. * This specification are subject to be changed without notice. 10.31.2000 1 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P FUNCTION BLOCK DIAGRAM CLK LXIN LXOUT RESET Reset Control Clock Generator Clock Mode Control Timing Generator System Control Data pointer Time Base Instruction Decoder Instruction Register ROM Stack ALU RAM Flag Z Timer/Counter (TA,TB) Stack pointer ACC Data Bus Interrupt Control C S PC HR I/O Control P0.0/WAKEUP0 P0.1/WAKEUP1 P0.2/WAKEUP2 P0.3/WAKEUP3 P4.0 P4.1 P4.2 P4.3 P8.0(INT1)/WAKEUPA P8.1(TRGB)/WAKEUPB P8.2(INT0)/WAKEUPC P8.3(TRGA)/WAKEUPD BZ2 Speech synthesizer BZ1 SEG0~SEG39 LCD Driver COM0~COM7 V1~V5 VA,VB LR PIN DESCRIPTIONS Symbol VDD,VDD2 Vss RESET Pin-type CLK LXIN LXOUT P0(0..3)/WAKEUP0..3 OSC-G OSC-B OSC-B INPUT-B P4(0..3) I/O-N RESET-A P8.0(INT1)/WAKEUPA I/O-L P8.2(INT0)/WAKEUPC P8.1(TRGB)/WAKEUPB I/O-L P8.3(TRGA)/WAKEUPD Function Power supply (+) Power supply (-) System reset input signal, low active mask option : none pull-up Capacitor connecting pin for internal high frequency oscillator. Crystal connecting pin for low speed clock source. Crystal connecting pin for low speed clock source. 4-bit input port with IDLE/STOP releasing function mask option : wakeup enable, pull-up wakeup enable, none wakeup disable, pull-up wakeup disable, pull-down wakeup disable, none 4-bit bidirection I/O port with high current source. mask option : open-drain push-pull, high current PMOS push-pull, low current PMOS 2-bit bidirection I/O port with external interrupt sources input and IDLE /STOP releasing function mask option : wakeup enable, push-pull wakeup disable, push-pull wakeup disable, open-drain 2-bit bidirection I/O port with time/counter A,B external input and IDLE /STOP releasing function * This specification are subject to be changed without notice. 10.31.2000 2 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P Symbol Pin-type mask option : BZ1, BZ2 V1, V2, V3, V4, V5, VA, VB COM0~COM7 SEG0~SEG39 TEST Function wakeup enable, push-pull wakeup disable, push-pull wakeup disable, open-drain Speech output pins LCD bias pins LCD common output pins LCD segment output pins Test pin must be connected to Vss FUNCTION DESCRIPTIONS PROGRAM ROM ( 16K X 8 bits ) 16 K x 8 bits program ROM contains user's program and some fixed data . The basic structure of the program ROM may be categorized into 5 partitions. 1. Address 0000h: Reset start address. 2. Address 0002h - 000Ch : 6 kinds of interrupt service routine entry addresses . 3. Address 000Eh-0086h : SCALL subroutine entry address, only available at 000Eh,0016h,001Eh,0026h, 002Eh, 0036h, 003Eh, 0046h, 004Eh, 0056h, 005Eh, 0066h, 006Eh, 0076h, 007Eh,0086h . 4. Address 0000h - 07FFh : LCALL subroutine entry address. 5. Address 0000h - 1FFFh : Except used as above function, the other region can be used as user's program and data region. address Bank 0 : 0000h 0002h 0004h 0006h 0008h 000Ah 000Ch 000Eh 0086h Reset start address INT0 ; interrupt service routine entry address SPI TRGA TRGB TBI INT1 Subroutine call entry address designated by [LCALL a] instruction SCALL, subroutine call entry address .. . 07FFh 0800h 0FFFh 1000h 1FFFh Bank 1 Bank 2 Data table for [LDAX],[LDAXI] instruction Bank 3 * This specification are subject to be changed without notice. 10.31.2000 3 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P User's program and fixed data are stored in the program ROM. User's program is executed using the PC value to fetch an instruction code. The 16Kx8 bits program ROM can be divided into 4 banks. There are 4Kx8 bits per bank. The program ROM bank is selected by P3(1..0). The program counter is a 13-bit binary counter. The PC and P3 are initialized to "0" during reset. When P3(1..0)=00B, the bank0 and bank1 of program ROM will be selected. P3(1..0)=01B, the bank0 and bank2 will be selected. Address 0000h : : 0FFFh 1000h : : 1FFFh P3=xx00B P3=xx01B P3=xx10B Bank0 Bank0 Bank0 Bank1 Bank2 Bank3 PROGRAM EXAMPLE: BANK 0 : : : LDIA #00H ; set program ROM to bank1 OUTA P3 B XA1 : XA : : : LDIA #01H ; set program ROM to bank2 OUTA P3 B XB1 : XB : : : LDIA #02H ; set program ROM to bank3 OUTA P3 B XC1 : XC : : : B XD XD : : : : ;--------------- -------------------- -------------------- -------------------- -BANK 1 XA1 : : : B XA : XA2 : : START: * This specification are subject to be changed without notice. 10.31.2000 4 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P B XA2 : ;--------------- -------------------- -------------------- -------------------- -BANK 2 XB1 : : : B XB : XB2 : : B XB2 : ;--------------- -------------------- -------------------- -------------------- -BANK 3 XC1 : : : B XC : XC2 : : B XC2 Fixed data can be read out by table-look-up instruction. Table-look-up instruction is requires the Data point (DP) to indicate the ROM address in obtaining the ROM code data (Except bank 0) : LDAX LDAXI Acc ← ROM[DP]L Acc ← ROM[DP]H,DP+1 DP is a 12-bit data register that stores the program ROM address as pointer for the ROM code data. User has to initially load ROM address into DP with instructions "LDADPL", and "LDADPM, LDADPH", then then to obtain the lower nibble of ROM code data by instruction "LDAX" and higher nibble by instruction "LDAXI" PROGRAM EXAMPLE: Read out the ROM code of address 1777h by table-look-up instruction. LDIA STADPL STADPM STADPH : LDL LDH LDAX STAMI LDAXI STAM ; ORG DATA #07h; ; [DP]L ← 07h ; [DP]M ← 07h ; [DP]H ← 07h, Load DP=777h #00h; #03h; ; ACC ← 6h ; RAM[30] ← 6h ; ACC ← 5h ; RAM[31] ← 5h 1777h 56h; DATA RAM ( 500-nibble ) A total 500 - nibble data RAM is available from address 000 to 1FFh Data RAM includes the zero page region, stacks and data areas. * This specification are subject to be changed without notice. 10.31.2000 5 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P Increment Address Bank 0 Increment Zero-page 000h - 00Fh 010h - 01Fh 020h - 02Fh : : : 0C0h - 0CFh 0D0h - 0DFh 0E0h - 0EFh 0F0h - 0F3h Bank 1 Level 0 Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 Level 9 Level 10 Level 11 Level 12 100h - 10Fh 110h - 11Fh : : : 1E0h - 1EFh 1F0h - 1FFh ZERO- PAGE: From 000h to 00Fh is the zero-page location. It is used as the zero -page address mode pointer for the instruction of "STD #k,y; ADD #k,y; CLR y,b; CMP y,b". PROGRAM EXAMPLE: To write immediate data "07h" to RAM [03] and to clear bit 2 of RAM [0Eh]. STD #07h, 03h ; RAM[03] ← 07h CLR 0Eh,2 ; RAM[0Eh]2 ← 0 STACK: There are 13 - level ( maximum ) stack levels that user can use for subroutine ( including interrupt and CALL). User can assign any level be the starting stack by providing the level number to stack pointer( SP) . When an instruction (CALL or interrupt) is invoked, before enter the subroutine, the previous PC address is saved into the stack until returned from those subroutines ,the PC value is restored by the data saved in stack. DATA AREA: Except the area used by user's application, the whole RAM can be used as data area for storing and loading general data. ADDRESSING MODE The 500 nibble data memory consists of two banks (bank 0 and bank 1). There are 244x4 bits (address 000h~0F3h) in bank 0 and 256x4 bits (address 100h~1FFh) in bank 1. * This specification are subject to be changed without notice. 10.31.2000 6 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P The bank is selected by P9.3. When P9.3 is cleared to "0", the bank 0 is selected. When P9.3 is set to "1", the bank 1 is selected. The Data Memory consists of three Address mode, namely (1) Indirect addressing mode: The address in the bank is specified by the HL registers. P9.3 HR LR RAM address PROGRAM EXAMPLE: Load the data of RAM address "143h" to RAM address "032h". SEP P9,3 LDL #3h LDH #4h LDAM CLP P9,3 LDL #2h LDH #3h STAM ; P9.3← 1 ; LR← 3 ; HR← 4 ; Acc← RAM[134h] ; P9.3← 0 ; LR← 2 ; HR← 3 ; RAM[023h]← Acc (2) Direct addressing mode: The address in the bank is directly specified by 8 bits code of the second byte in the instruction field. instruction field xxxx xxxx P9.3 xxxx xxxx RAM address PROGRAM EXAMPLE: Load the data of RAM address "143h" to RAM address "023h". SEP P9,3 LDA 43h CLP P9,3 STA 23h ; P9.3← 1 ; Acc← RAM[143h] ; P9.3← 0 ; RAM[023h]← Acc (3) Zero-page addressing mode: The zero-page is in the bank 0 (address 000h~00Fh). The address is the lower 4 bits code of the second byte in the instruction field. instruction field yyyy RAM address 0 0000 yyyy PROGRAM EXAMPLE: Write immediate "0Fh" to RAM address "005h". STD #0Fh, 05h ; RAM[05h]← 0Fh * This specification are subject to be changed without notice. 10.31.2000 7 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P PROGRAM COUNTER (16K ROM) Program counter ( PC ) is composed by a 13-bit counter, which indicates the next executed address for the instruction of program ROM instruction. For BRANCH and CALL instructions, PC is changed by instruction indicating. PC only can indicate the address from 0000h-1FFFh. The bank number is decided by P3. (1) Branch instruction: SBR a Object code: 00aa aaaa Condition: SF=1; PC ← PC 12-6.a ( branch condition satisified ) PC Hold original PC value+1 a a a a a a SF=0; PC← PC +1( branch condition not satisified) PC Original PC value + 1 LBR a Object code: 1100 aaaa aaaa aaaa Condition: SF=1; PC ← PC 12.a ( branch condition satisified ) PC Hold +2 a a a a a a a a a a a a SF=0; PC← PC +2( branch condition not satisified) PC Original PC value + 2 SLBR a Object code: 0101 0101 1100 aaaa aaaa aaaa (a:1000h~1FFFh) 0101 0111 1100 aaaa aaaa aaaa (a:0000h~0FFFh) Condition: SF=1; PC ← a ( branch condition satisified) PC a a a a a a a a a a a a a SF=0 ; PC ← PC + 3 ( branch condition not satisified ) PC Original PC value + 3 (2) Subroutine instruction: SCALL a Object code: 1110 nnnn Condition : PC ← a ; a=8n+6 ; n=1..Fh ; a=86h, n=0 PC 0 0 0 0 0 a a a a a LCALL a Object code: 0100 0aaa aaaa aaaa Condition: PC ← a * This specification are subject to be changed without notice. a a a 10.31.2000 8 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P PC 0 0 a a a a a a a a a a a RET Object code: 0100 1111 Condition: PC ← STACK[SP]; SP + 1 PC The return address stored in stack RT I Object code: 0100 1101 Condition : FLAG. PC ← STACK[SP]; EI ← 1; SP + 1 PC The return address stored in stack (3) Interrupt acceptance operation: When an interrupt is accepted, the original PC is pushed into stack and interrupt vector will be loaded into PC,The interrupt vectors are as follows : INT0 (External interrupt from P8.2) PC 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 1 0 SPI (speech end interrupt) PC 0 0 0 TRGA (Timer A overflow interrupt) PC 0 0 0 0 0 TRGB (Time B overflow interrupt) PC 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 1 0 TBI (Time base interrupt) PC 0 0 0 INT1 (External interrupt from P8.0) PC 0 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 (4) Reset operation: PC 0 0 * This specification are subject to be changed without notice. 10.31.2000 9 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P (5) Other operations: For 1-byte instruction execution: PC + 1 For 2-byte instruction execution: PC + 2 For 3-byte instruction execution: PC + 3 ACCUMULATOR Accumulator(ACC) is a 4-bit data register for temporary data storage. For the arithematic, logic and comparative opertion.., ACC plays a role which holds the source data and result . FLAGS There are three kinds of flag, CF ( Carry flag ), ZF ( Zero flag ) and SF ( Status flag ), these three 1-bit flags are included by the arithematic, logic and comparative .... operation . All flags will be put into stack when an interrupt subroutine is served, and the flags will be restored after RTI instruction is executed . (1) Carry Flag ( CF ) The carry flag is affected by the following operations: a. Addition : CF as a carry out indicator, under addition operation, when a carry-out occures, the CF is "1", likewise, if the operation has no carry-out, CF is "0". b. Subtraction : CF as a borrow-in indicator, under subtraction operation, when a borrow occures, the CF is "0", likewise, if there is no borrow-in, the CF is "1". c. Comparision: CF as a borrow-in indicator for Comparision operation as in the subtraction operation. d. Rotation: CF shifts into the empty bit of accumulator for the rotation and holds the shift out data after rotation. e. CF test instruction : Under TFCFC instruction, the CF content is sent into SF then clear itself as "0". Under TTSFC instruction, the CF content is sent into SF then set itself as "1". (2) Zero Flag ( ZF ) ZF is affected by the result of ALU, if the ALU operation generates a "0" result, the ZF is "1", likewise, the ZF is "0". (3) Status Flag ( SF ) The SF is affected by instruction operation and system status . a. SF is initiated to "1" for reset condition . b. Branch instruction is decided by SF, when SF=1, branch condition is satisified, likewise, when SF = 0, branch condition is unsatisified . * This specification are subject to be changed without notice. 10.31.2000 10 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P PROGRAM EXAMPLE: Check following arithematic operation for CF, ZF, SF CF - LDIA #00h; LDIA #03h; ADDA #05h; ADDA #0Dh; ADDA #0Eh; ZF 1 0 0 0 0 SF 1 1 1 0 0 ALU The arithematic operation of 4 - bit data is performed in ALU unit . There are 2 flags that can be affected by the result of ALU operation, ZF and SF . The operation of ALU is affected by CF only . ALU STRUCTURE ALU supported user arithematic operation functions, including Addition, Subtraction and Rotaion. DATA BUS ALU ZF CF SF ALU FUNCTION (1) Addition: ALU supports addition function with instructions ADDAM, ADCAM, ADDM #k, ADD #k,y .... . The addition operation affects CF and ZF. Under addition operation, if the result is "0", ZF will be "1", otherwise, ZF will be "0", When the addition operation has a carry-out. CF will be "1", otherwise, CF will be "0". EXAMPLE: Operation 3+4=7 7+F=6 0+0=0 8+8=0 Carry 0 1 0 1 Zero 0 0 1 1 (2) Subtraction: ALU supports subtraction function with instructions SUBM #k, SUBA #k, SBCAM, DECM... . The subtraction operation affects CF and ZF, Under subtraction operation, if the result is negative, CF will be "0", and a borrow out, otherwise, if the result is positive, CF will be "1". For ZF, if the result of subtraction operation is "0", the ZF is "1", likewise, ZF is "1". * This specification are subject to be changed without notice. 10.31.2000 11 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT EXAMPLE: inary m i l e r P Operation 8-4=4 7-F= -8(1000) 9-9=0 Carry 1 0 1 Zero 0 0 1 (3) Rotation: Two types of rotation operation are available, one is rotation left, the other is rotation right. RLCA instruction rotates Acc value counter-clockwise, shift the CF value into the LSB bit of Acc and hold the shift out data in CF. MSB LSB ACC CF RRCA instruction operation rotates Acc value clockwise, shift the CF value into the MSB bit of Acc and hold the shift out data in CF. MSB LSB ACC CF PROGRAM EXAMPLE: To rotate Acc clockwise (right) and shift a "1" into the MSB bit of Acc . TTCFS; CF ← 1 RRCA; rotate Acc right and shift CF=1 into MSB. HL REGISTER HL register are two 4-bit registers, they are used as a pair of pointer for the RAM memoryaddress. They are used as also 2 independent temporary 4-bit data registers. For certain instructions, L register can be a pointer to indicate the pin number ( Port4 only ) . HL REGISTER STRUCTURE 3 2 1 0 3 2 1 0 H REGISTER L REGISTER HL REGISTER FUNCTION (1) HL register is used as a temporary register for instructions : LDL #k, LDH #k, THA, THL, INCL, DECL, EXAL, EXAH, . PROGRAM EXAMPLE: Load immediate data "5h" into L register, "0Dh" into H register. LDL #05h; LDH #0Dh; (2) HL register is used as a pointer for the address of RAM memory for instructions : LDAM, STAM, STAMI .., PROGRAM EXAMPLE: Store immediate data "#0Ah" into RAM of address 35h. * This specification are subject to be changed without notice. 10.31.2000 12 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P LDL #5h; LDH #3h; STDMI #0Ah ; RAM[35] ← Ah (3) L register is used as a pointer to indicate the bit of I/O port for instructions : SELP, CLPL, TFPL, (When LR = 0 indicate P4.0) PROGRAM EXAMPLE: To set bit 0 of Port4 to "1" LDL SEPL #00h; ; P4.0 ← 1 STACK POINTER (SP) Stack pointer is a 4-bit register that stores the present stack level number. Before using stack, user must set the SP value first, CPU will not initiate the SP value after reset condition . When a new subroutine is received, the SP is decreased by one automatically, likewise, if returning from a subroutine, the SP is increased by one . The data transfer between ACC and SP is done with instructions "LDASP" and "STASP". DATA POINTER (DP) Data pointer is a 12-bit register that stores the ROM address can indicating the ROM code data specified by user (refer to data ROM). CLOCK AND TIMING GENERATOR The clock generator is supported by a dual clock system. The high-frequency oscillator is internal oscillator, the working frequency is 4.6 MHz. The low-frequency oscillator may be sourced from crystal or RC oscillator as defined by mask option, the working frequency is 32 KHz. CLOCK GENERATOR STRUCTURE There are two clock generator for system clock control unit, P14 is the status register that hold the CPU status. P16, P19 and P22 are the command register for system clock mode control. CLK High-frequency generator fc LXIN LXOUT Low-frequency generator P14 fs P16 System clock mode control P19 P22 System control LXIN VDD R LXIN LXOUT open LXOUT Crystal connection RC oscillator connection R=1.2MΩ * This specification are subject to be changed without notice. 10.31.2000 13 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P SYSTEM CLOCK MODE CONTROL The system clock mode controller can start or stop the high-frequency and low-frequency clock oscillator and switch between the basic clocks. EM73983 has four operation modes (DUAL, SLOW,IDLE and STOP operation modes). STOP operation mode I/O wakeup High osc : stopped Low osc : stopped Command (P16) Reset Reset Command (P16) Command (P22) Command (P22) Reset release RESET operation High osc : oscillating Low osc : oscillating NORMAL operation mode Reset SLOW operation mode High osc : stopped Low osc : oscillating Command (P19) Reset I/O or internal timer wakeup IDLE (CPU stops) High osc : stopped Low osc : oscillating Operation Mode NORMAL SLOW IDLE STOP Oscillator System Clock Available function One instruction cycle High, Low frequency High frequency clock LCD, speech, sound gen. 8 / fc Low frequency Low frequency clock LCD 8 / fs Low frequency CPU stops LCD None CPU stops All disable - DUAL OPERATION MODE The 4-bit µc is in the DUAL operation mode when the CPU is reseted. This mode is dual clock system (high-frequency and low-frequency clocks oscillating). It can be changed to SLOW or STOP operation mode with the command register (P22 or P16). LCD display, speech synthesizer and sound generator are available for the DUAL operation mode. SLOW OPERATION MODE The SLOW operation mode is single clock system (low-frequency clock oscillating). It can be changed to the DUAL operation mode with the command register (P22), STOP operation mode with P16 and IDEL operation mode with P19. LCD display is available for the SLOW operation mode. Speech synthesizer and sound generator are disabled in this mode. * This specification are subject to be changed without notice. 10.31.2000 14 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P P22 3 * 2 SOM 0 0 0 1 * * P14 3 * 1 SOM 0 Initial value : 0000 Select operation mode DUAL operation mode SLOW operation mode 2 WKS 1 0 LFS CPUS Initial value : *000 LFS 0 1 Low-frequency status LXIN source is not stable LXIN source is stable WKS 0 1 Wakeup status Wakeup not by internal timer Wakeup by internal timer CPUS 0 1 CPU status DUAL operation mode SLOW operation mode Port14 is the status register for CPU. P14.0 (CPU status) and P14.1 (Low-frequency status) are read-only bits. P14.2 (wakeup status) will be set as '1' when CPU is waked by internal timer. P14.2 will be cleared as '0' when user out data to P14. IDLE OPERATION MODE The IDLE operation mode suspends all CPU functions except the low-frequency clock oscillation and the LCD driver. It keeps the internal status with low power consumption without stopping the slow clock oscillator and LCD display. LCD display is available for the IDLE operation mode. Sound generator is disabled in this mode. The IDLE operation mode will be wakeup and return to the SLOW operation mode by the internal timing generator or I/O pins (P0(0..3)/WAKEUP 0..3 and P8(0..3)/WAKEUPA..D). P19 3 * IDME 1 0 2 IDME 1 0 SIDR Enable IDLE mode Enable IDLE mode no function Initial value : 0000 SIDR 0 0 0 1 1 0 1 1 Select IDLE releasing condition P0(0..3), P8(0..3) pin input P0(0..3), P8(0..3) pin input and 1 sec signal P0(0..3), P8(0..3) pin input and 0.5 sec signal P0(0..3), P8(0..3) pin input and 15.625 ms signal STOP OPERATION MODE The STOP operation mode suspends system operation and holds the internal status immediately before the suspension with low power consumption. This mode will be released by reset or I/O pins (P0(0..3)/ WAKEUP 0..3 and P8(0..3)/WAKEUP A..D). LCD display and sound generator are disabled in the STOP operation mode. * This specification are subject to be changed without notice. 10.31.2000 15 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P P16 3 * 2 SPME SPME 1 0 1 0 SWWT Initial value : 0000 Enable STOP mode Enable STOP mode no function SWWT 0 0 0 1 1 0 1 1 Set wake-up warm-up time 214/LXIN 210/LXIN 212/LXIN no function TIME BASE INTERRUPT (TBI ) The time base can be used to generate a single fixed frequency interrupt . Eight types of frequencies can be selected with the "P25" setting. P25 3 2 1 0 initial value : 0000 0 0 0 0 0 1 1 1 1 1 P25 0 x 1 0 1 0 1 1 1 1 1 0 1 0 1 1 1 1 0 x x 0 1 0 1 0 1 0 1 x DUAL operation mode Interrupt disable Interrupt frequency LXIN / 23 Hz Interrupt frequency LXIN / 24 Hz Interrupt frequency LXIN / 25 Hz Interrupt frequency LXIN / 214 Hz Interrupt frequency LXIN / 21 Hz Interrupt frequency LXIN / 26 Hz Interrupt frequency LXIN / 28 Hz Interrupt frequency LXIN / 210 Hz Reserved SLOW operation mode Interrupt disable Reserved Reserved Reserved Interrupt frequency LXIN / 214 Hz Reserved Interrupt frequency LXIN / 26 Hz Interrupt frequency LXIN / 28 Hz Interrupt frequency LXIN / 210 Hz Reserved TIMER / COUNTER ( TIMERA, TIMERB) Timer/counters support three special functions: 1. Even counter 2. Timer. 3. Pulse-width measurement. These three functions can be executed by 2 timer/counter independently. With timerA, the counter data is saved in timer register TAH, TAM, TAL. User can set counter initial value and read the counter value by instruction "LDATAH(M,L)" and "STATAH(M,L)". With timer B register is TBH, TBM, TBL and the W/R instruction are "LDATBH (M,L)" and "STATBH (M,L)". The basic structure of timer/counter is composed by two identical counter module , these two modules can be set initial timer or counter value to the timer registers, P28 and P29 are the command registers for timerA and timer B, user can choose different operation modes and internal clock rates by setting these two registers. When timer/counter overflows, it will generate a TRGA(B) interrupt request to interrupt control unit. * This specification are subject to be changed without notice. 10.31.2000 16 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P INTERRUPT CONTROL TRGB request TRGA request DATA BUS P8.3/ TRGA 12 BIT COUNTER 12 BIT COUNTER EVENT COUNTER CONTROL EVENT COUNTER CONTROL TIMER CONTROL TIMER CONTROL PULSE-WIDTH MEASUREMENT CONTROL PULSE-WIDTH MEASUREMENT CONTROL internal clock P28 TMSA IPSA P29 TMSB P8.1/ TRGB internal clock IPSB TIMER/COUNTER CONTROL P8.1/TRGB, P8.3/TRGA are the external timer inputs for timerB and timerA, they are used in event counter and pulse-width measurement mode. Timer/counter command port: P28 is the command port for timer/counterA and P29 is for the timer/ counterB. Port 28 3 2 1 TMSA 0 IPSA Initial state: 0000 Port 29 3 2 TMSB 1 0 IPSB TIMER/COUNTER MODE SELECTION TMSA (B) Function description 00 Stop 0 1 Event counter mode 1 0 Timer mode 11 Pulse width measurement mode Initial state: 0000 INTERNAL PULSE-RATE SELECTION IPSA(B) DUAL mode SLOW mode 0 0 LXIN/23 Hz Reserved 0 1 LXIN/2 7 Hz LXIN/2 Hz 1 0 LXIN/2 11Hz LXIN/2 Hz 1 1 LXIN/2 15 Hz LXIN/215Hz * This specification are subject to be changed without notice. 7 11 10.31.2000 17 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P TIMER/COUNTER FUNCTION Timer/counterA,B are programmable for timer, event counter and pulse width measurement mode. Each timer/counter can execute any of these functions independently. EVENT COUNTER MODE under event counter mode, the timer/counter is increased by one at any rising edge of P8.1/TRGB for timerB (P8.3/TRGA for timer A). When timerB (timerA) counts overflow, it will provide an interrupt request TRGB (TRGA) to interrupt control unit. P8.1/TRGB (P8.3/TRGA) TimerB (TimerA) value n n+1 n+2 n+3 n+4 n+5 n+6 PROGRAM EXAMPLE: Enable timerA with P28 LDIA OUTA #0100b; P28 ; Enable timerA with event counter mode TIMER MODE Under timer mode ,the timer/counter is increased by one at any rising edge of internal pulse . User can choose up to 4 types of internal pulse rate by setting IPSB for timerB (IPSA for timerA). When timer/counter counts overflow, An interrupt request will be sent to interrupt control unit. Internal pulse TimerB (TimerA )value n n+1 n+2 n+3 n+4 n+5 n+6 n+7 PROGRAM EXAMPLE: To generate TRGA interrupt request after 60 ms with system clock LXlN=32KHz LDIA #0100B; EXAE EICIL 110111b LDIA #0Ah; STATAL; LDIA #00h; STATAM; LDIA #0Fh; STATAH; LDIA #1000B; OUTA P28 NOTE: ;enable mask 2 ; interrupt latch ←0, enable EI ; enable timerA with internal pulse rate: LXIN/23 Hz The preset value of timer/counter register is calculated as following procedure. Internal pulse rate: LXIN/23 ; LXIN = 32KHz The time of timer counter count one = 23 /LXIN = 8/32768=0.244ms The number of internal pulse to get timer overflow = 60 ms/ 0.244ms = 245.901= 0F6h The preset value of timer/counter register = 1000h - 0F6h = F0Ah PULSE WIDTH MEASUREMENT MODE * This specification are subject to be changed without notice. 10.31.2000 18 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P Under the pulse width measurement mode, the counter is incresed at the rising edge of internal pulse during external timer/counter input (P8.1/TRGB, P8.3/TRGA ) in high level, interrupt request is generated as soon as timer/counter count overflow. P8.1/TRGB(P8.3/TRGA) Internal pulse TimerB(TimerA) value n n+1 n+2 n+3 n+4 n+5 PROGRAM EXAMPLE: Enable timerA by pulse width measurement mode . LDIA OUTA #1100b; P28 ; Enable timerA with pulse width measurement mode. INTERRUPT FUNCTION Six interrupt sources are available, 2 from external interrupt sources and 4 from internal interrupt sources . Multiple interrupts are admitted according to their priority . Type External Internal Internal Internal Internal External Interrupt source External interrupt(INT0) speech end interrupt (SPI) TimerA overflow interrupt (TRGA) TimerB overflow interrupt (TRGB) Time base interrupt(TBI) External interrupt(INT1) Priority Interrupt Latch Interrupt Enable condition Program ROM entry address 1 2 3 4 5 6 IL5 IL4 IL3 IL2 IL1 IL0 EI=1 EI=1, MASK3=1 EI=1, MASK2=1 EI=1, MASK1=1 002h 004h 006h 008h 00Ah 00Ch EI=1,MASK0=1 INTERRUPT STRUCTURE MASK0 MASK1 MASK1 MASK2 MASK3 INT1 r0 Reset by system reset and program instruction IL0 TBI r1 IL1 TRGB TRGA r2 r3 IL2 IL3 SPI INT0 r5 IL4 IL5 r4 Priority checker Reset by system reset and program instruction Set by program instruction EI Interrupt request Entry address generator Interrupt entry address Interrupt controller: IL0-IL5 : Interrupt latch . Hold all interrupt requests from all interrupt sources. IL's can not be set by program, but can be reset by program or system reset, so IL can only decide which interrupt source can be accepted. MASK0-MASK3 : Except INT0 ,MASK register may permit or inhibit all interrupt sources. * This specification are subject to be changed without notice. 10.31.2000 19 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P EI : Enable interrupt Flip-Flop may promit or inhibit all interrupt sources, when interrupt occurs, EI is auto cleared to "0", after RTI instruction is executed, EI is auto set to "1" again . Priority checker: Check interrupt priority when multiple interrupts occur. INTERRUPT OPERATION The procedure of interrupt operation: 1. Push PC and all flags to stack. 2. Set interrupt entry address into PC. 3. Set SF= 1. 4. Clear EI to inhibit other interrupts occur. 5. Clear the IL with which interrupt source has already been accepted. 6. Excute interrupt subroutine from the interrupt entry address. 7. CPU accept RTI, restore PC and flags from stack . Set EI to accept other interrupt requests. PROGRAM EXAMPLE: To enable interrupt of "INT0, TRGA" LDIA #0100B; EXAE; set mask register "1100b" EICIL 010111B ; enable interrupt F.F. and clear IL3 and IL5 LCD DRIVER It can directly drive the liquid crystal display ( LCD ) and has 40 segments , 8 commons output pins. There are total 40x8 dots can be display. The V1~V5 are the LCD bias voltage input pins. (1) LCD driver control command register: Port27 3 2 1 0 Initial value: 0000 LDC * * LCD DISPLAY CONTROL LDC Function description 0 0 LCD display disable 0 1 Blanking 1 0 no function 1 1 LCD display enable * : Don't care . P27 is the LDC driver control command register . The initial value is 0000 . When LDC ( bit2 and bit3 of P27 ) is set to "00", the LCD display is disabled . When LDC is set to Ò01Ó, the LCD is blanking, the COM pins are inactive and the SEG pins output the display data continuously. When LDC is set to "11", the LCD display is enabled. (2) LCD display data area: The LCD display data is stored in the display data area of the data memory ( RAM) . The LCD display data area is as illustrated below: * This specification are subject to be changed without notice. 10.31.2000 20 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P The display data from the display data area are automatically read out and send to the LCD driver directly by the hardware . Therefore, the display patterns can be changed only by overwritting the contents of the display data area through software . The dispaly memory area that is not used to store the LCD display data could be used as the ordinary data memory. LCD display data area : Bank1 P9.3=1 0 1 2 3 4 100-10Fh 110-11Fh 120-12Fh 130-13Fh 140-14Fh 150-15Fh 160-16Fh 170-17Fh 180-18Fh 190-19Fh 1A0-1AFh 1B0-1BFh 1C0-1CFh 1D0-1DFh 1E0-1EFh 1F0-1FFh 5 6 7 8 9 A B C D E F SEG0 SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 SEG34 SEG35 SEG36 SEG37 SEG38 SEG39 COM0 COM1 COM2 COM3 COM4 COM5 COM6 COM7 P26 is the start address register of LCD common pin. Port26 3 2 1 0 Initial value: 0000 CSA Common start address register RAM CSA 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 100109h 110119h 120129h 130139h COM0 COM1 COM2 COM3 COM0 COM1 COM2 COM0 140149h 150159h 160169h 170179h COM4 COM5 COM6 COM7 COM3 COM4 COM5 COM6 COM7 COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM0 COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM0 COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM0 COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM0 COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM0 COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM0 COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM0 COM1 COM2 COM3 COM4 COM5 COM6 COM0 COM1 COM2 COM3 COM4 COM5 COM0 COM1 COM2 COM3 COM4 COM0 COM1 COM2 COM3 COM0 COM1 COM2 COM0 COM1 COM7 COM6 COM7 COM5 COM6 COM7 COM4 COM5 COM6 COM7 COM3 COM4 COM5 COM6 COM7 COM2 COM3 COM4 COM5 COM6 COM7 COM1 COM2 COM3 COM4 COM5 COM6 COM7 180189h 190199h 1A01A9h 1B01B9h 1C01C9h 1D01D9h 1E01F01EF9h 1F9h COM0 PROGRAM EXAMPLE: LDIA OUTA LDIA OUTA LDIA SEP STA #0000B P26 #1100B ; LCD display enable P27 #1010B ; store 1010B to RAM[101h] P9,3 01H * This specification are subject to be changed without notice. 10.31.2000 21 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P (3) LCD waveform : (1/5 bias) S E G 0 COM0 * TYPE A : * TYPE B : COM0 COM0 V5 V5 V4 V3 V2 V1 Vss : ON : OFF V4 V3 V2 V1 Vss COM1 COM1 SEG0 SEG0 SEG0-COM0 SEG0-COM0 ON ON SEG0-COM1 SEG0-COM1 OFF OFF COM7 Frame freq.=64Hz Frame freq.=64Hz (4) LCD drive voltage : • The LCD bias voltage is supplied by voltage multiplier. The application circuit is illustated as below : VA 0.1µF VB 0.1µF V5 V4 V3 V2 V1 0.1µF 0.1µF 0.1µF 0.1µF SPEECH SYNTHESIZER Set sound freq. Set sound mode P23,24 Write P30 Write Set sound effect amplitude P17 Write BZ1 PWM Sound effect generator speech ROM P7 Write P7 Read speech decoder BZ2 SPI interrupt P5.3 read P6 Write P5 Write Set data address (write 5 times) Read data Set speech address (write 4 times) Speech active Set sample rate Block diagram of speech and sound effect * This specification are subject to be changed without notice. 10.31.2000 22 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P EM73983 speech synthesizer operates as following : 1. Send the speech start address to the address latch by writing P6 four times. 2. Choose the sampling rate, enable the speech synthesizer by writing P5. 3. The ROM address counters send the ROM address A6 .. A17 to the speech ROM. 4. ACT is the speech acknowledge signal. When the speech synthesizer has voice output. ACT is high . When ACT is changed from high to low, the speech synthesizer can generate the speech ending interrupt SPI. The ACT signal can be read from P5.3. SPEECH SYNTHESIZER CONTROL Speech sample rate control register (P5 write) : 3 2 1 0 Initial value : *111 SR SR 000 001 010 011 100 101 111 Sample rate selection PWM on CLK/64/1/3 CLK/64/1/4 CLK/64/2/3 CLK/64/2/4 CLK/64/3/3 CLK/64/3/4 PWM off Speech active flag (P5 read) : 3 2 1 0 ACT * * * Sample rate 24K 18K 12K 9K 8K 6K port 5 -- initialization is "*111". port 6 -- initialization is pointed to the lownibble of start address latch. CLK=4.6 MHz Initial value : 0*** ACT is the speech acknowledge signal. When the speech synthesizer has voice output, ACT is high. When ACT is high → low, the speech synthesizer can generate the speech ending interrupt SPI. Speech start address register (P6 write) : 3 2 1 Port 6 P6L1 A9 A8 A7 0 A6 Initial value : 1111 P6L2 A13 A12 A11 A10 P6L3 A17 A16 A15 A14 P6L4 - - - - Send the speech start address to the speech synthesizer by writing P6 four times. There is a pointer counter to point the address latch (P6L1, P6L2, P6L3, P6L4). It will increase one when write P6. So, the first time writing P6 to P6L1, the second time is P6L2, the third time is P6L3, the fourth time is P6L4 and the fifth time is P6L1 latch again, ... etc. The pointer counter point to P6L1 when CPU is reset or P5 is writen. In the NORMAL operation mode, the speech synthesizer is available. In the other operation modes, it is disable. * This specification are subject to be changed without notice. 10.31.2000 23 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P PROGRAM EXAMPLE: SP_ADR1 EQU : LDIA OUTA LDIA OUTA LDIA OUTA LDIA OUTA ; set sample rate & start speech LDIA OUTA ; wait speech end WAIT TTP B 1234H ; the start address of the speech section #SP_ADR1 P6 #SP_ADR1/10H P6 #SP_ADR1/100H P6 #SP_ADR1/1000H P6 #0010B P5 P5,3 WAIT ; get speech active flag USING SPEECH ROM AS DATA ROM The speech ROM can be used for speech synthesizer and for data ROM simutaneously. First, write initial address to P7 (five times), and after four cycles, you can read P7 to get data, and address counter increases one automatically.The following read operations must be at an internval of instruction cycles which are more than 3. The read operation should be all done before you leave normal mode and change to slow mode. Get speech ROM data (P7 read) : 3 2 1 0 Port 7 Set speech ROM address (P7 write) : 3 2 1 0 Port 7 P7L1 A3 A2 A1 A0 P7L2 A7 A6 A5 A4 P7L3 P7L4 A11 A10 A9 A8 A15 A14 A13 A12 P7L5 - A17 A16 PROGRAM EXAMPLE: D_ADR1 EQU : LDIA OUTA LDIA OUTA LDIA OUTA LDIA OUTA LDIA OUTA 12345H ; the start address of the speech ROM #D_ADR1 P7 #D_ADR1/10H P7 #D_ADR1/100H P7 #D_ADR1/1000H P7 #D_ADR1/10000H P7 * This specification are subject to be changed without notice. 10.31.2000 24 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P NOP NOP NOP NOP ; READ DATA INA STA NOP 4 cycles P7 TEMP ; read D_ADR1 3 cycles INA P7 ; read D_ADR1+1 MELODY (SOUND EFFECT) CONTROL One channel melody/sound effect output, controlled by port 23, 24, 17, and 30. There is a built-in sound effect. It includes the tone generator and random generator. The tone generator is a binary down counter and the random generator is a 9-bit liner feedback shift register. P30 P23,P24 f2 Tone 4 kinds f1 generator of divider CLK/8 ÷2 ÷2 Output control f2x2 Random generator PWM ckt. Sound effect command register (P30) There are 4 kinds of basic frequency for sound generator which can be selected by P30. The output of sound effect is tone and random combination. Port30 3 2 BFREQ 1 0 SMODE Initial value : 0000 BFREQ Basic frequency (f1) select 0 0 CLK/16 0 1 CLK/32 1 0 CLK/64 1 1 Reserved (CLK=4.6MKz) SMODE 0 0 0 1 1 0 1 1 Sound generator mode Disable Tone output Random output Tone+random output Tone frequency register (P23, P24) The 8-bit tone frequency register is P24 and P23. The tone frequency will be changed when user output the different data to P23. Thus, the data must be output to P24 before P23 when users want to change the 8bit tone frequency (TF). Port24 Port23 3 2 1 0 Higher nibble register 3 2 1 0 Initial value : 1111 1111 Lower nibble register ** f1=CLK/2X, f2=f1/(TF+1)/2, TF=1~255, TF-0 ** Example : CLK=4.6 MHz, BFREQ=10, TF=00110001B. ⇒ f1=71680Hz, f2=71680Hz/50/2=716.8Hz * This specification are subject to be changed without notice. 10.31.2000 25 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P Random generator + f(x)=x9+x4+1 1 2 3 4 5 6 7 8 9 Volume control register (P17) The are 16 levels of volume for sound generator. P17 is the volume control register. Port17 Initial value : 1111 3 2 1 0 VCR VCR ts/tp ts 1 1 1 1 15/16 1 1 1 0 14/16 1 tp= CLK/64 (CLK=4.6MHz) : : tp 0 0 0 1 1/16 0 0 0 0 0/16 PROGRAM EXAMPLE: LDIA OUTA LDIA OUTA LDIA OUTA LDIA OUTA #1001B P30 #0111B P17 #0011B P24 #0001B P23 ; basic frequency : CLK/32, tone output ; volume control ; 1430 Hz tone output WATCH-DOG-TIMER (WDT) Watch-dog-timer can help user to detect the malfunction (runaway) of CPU and give system a timeup signal every certain time . User can use the time up signal to give system a reset signal when system is fail. This function is available by mask option. If the mask option of WDT is enabled, it will stop counting when CPU is reseted or in the STOP operation mode. The basic structure of Watch-Dog-Timer control is composed by a 4-stage binary counter and a control unit . The WDT counter counts for a certain time to check the CPU status, if there is no malfunction happened, the counter will be cleared and continue counting . Otherwise, if there is a malfunction happened, the WDT control will send a WDT signal ( low active ) to reset CPU. The WDT checking period is assign by P21 ( WDT command port ). WDT counter LXIN/213 0 1 2 3 RESET pin counter clear request mask option WDT control P21 WDT command port * This specification are subject to be changed without notice. 10.31.2000 26 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P P21 is the control port of watch-dog-timer, and the WDT time up signal is connected to RESET. Port 21 3 CWC 2 * 1 * 0 Initial value :0000 WDT CWC 0 1 Clear watchdog timer counter Clear counter then return to 1 Nothing WDT 0 1 Set watch-dog-timer detect time 3 x 213/LXIN = 3 x 213/32K Hz = 0.75 sec 7 x 213/LXIN = 7 x 213/32K Hz = 1.75 sec PROGRAM EXAMPLE To enable WDT with 7 x 213/LXIN detection time. LDIA #0001B OUTA P21 ; set WDT detection time and clear WDT counter : : RESETTING FUNCTION When CPU in normal working condition and RESET pin is held in low level for three instruction cycles at least, then CPU begins to initialize the whole internal states, when RESET pin changes to high level, CPU begins to work in normal condition. The CPU internal state during reset condition is as following table : Hardware condition in RESET state Program counter Status flag Interrupt enable flip-flop ( EI ) MASK0 ,1, 2, 3 Interrupt latch ( IL ) P3, 9, 13, 14, 16, 17, 19, 21, 22, 25, 26, 27, 28, 29, 30 P5, 23, 24 CLK, LXIN Initial value 0000h 01h 00h 00h 00h 00h 0Fh Start oscillation The RESET pin is a hysteresis input pin and it has a pull-up resistor available by mask option. The simplest RESET circuit is connect RESET pin with a capacitor to Vss and a diode to VDD. RESET * This specification are subject to be changed without notice. 10.31.2000 27 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P EM73983 I/O PORT DESCRIPTION : Port 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 E E I I E I Input function Input port , wakeup function ---Input port P5.3 : Speech active signal (ACT) -DATA ROM data Input port, wakeup function, external interrupt input -----CPU status register -- Output function I E I I I E I I I I I I I I I I I I I I Note --P3(1..0) : ROM bank selection Output port Speech sample rate register Speech start address register Data start address register Output port P9.3 : RAM bank selection ------STOP mode control register Sound effect volume control register -IDLE mode control register -WDT control register DUAL/SLOW mode control register Sound effect frequency register Sound effect frequency register Timebase control register LCD common start address register LCD control register Timer/counter A control register Timer/counter B control register Sound effect command register -- * This specification are subject to be changed without notice. low nibble high nibble 10.31.2000 28 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P APPLICATION CIRCUIT 100 VBAT 0.1µF VBAT 0.1µF VDD VDD2 P0.0 3V P0.1 SEG0~ SEG39 COM0~ COM7 LCD PANNEL VA P0.2 0.1µF VB V5 V4 V3 V2 V1 BZ1 100Ω BZ2 RESET 0.1µF LXOUT all 0.1µF 32.768KHz LXIN RESET 20P VSS CLK 0.022µF EM73983 * This specification are subject to be changed without notice. 10.31.2000 29 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P ABSOLUTE MAXIMUM RATINGS Items Sym. Supply Voltage Input Voltage Output Voltage Power Dissipation Operating Temperature Storage Temperature Ratings VDD VIN VO PD TOPR TSTG Conditions -0.5V to 6V -0.5V to VDD+0.5V -0.5V to VDD+0.5V 300mW 0oC to 50oC -55oC to 125oC TOPR=50oC RECOMMANDED OPERATING CONDITIONS Items Sym. Supply Voltage Input Voltage Ratings VDD VIH VIL FC FS Operating Frequency Condition 2.2V to 4.8V 0.90xVDD to VDD 0V to 0.10xVDD 4.6MHz 32KHz CLK LXIN,LXOUT DC ELECTRICAL CHARACTERISTICS (VDD=3±0.3V, VSS=0V, TOPR=25oC) Parameters Sym. Min. Typ. Max. Unit Conditions Supply current Hysteresis voltage IDD Input current VHYS+ VHYSIIH Output voltage IIL VOH Leakage current Input resistor Output current of BZ1, BZ2 LCD bias voltage VOL ILO RIN IOH IOL V1 V2 V3 V4 V5 - 0.5 1.2 mA - 25 38 µA - 12 1 2.4 7 0.1 -250 - ±1 ±1 -500 - µA µA V V µA µA µA V 2.0 2.4 - V 100 150 30 30 - 0.15 200 300 0.9 1.8 2.7 3.6 4.5 0.3 1 300 450 - V µA KΩ KΩ mA mA V V V V V 0.50VDD 0.20VDD 0.75VDD 0.40VDD * This specification are subject to be changed without notice. VDD=3.3V,no load,NORMAL mode,Fs=32KHz Fc=4.6MHz VDD=3.3V,no load,SLOW mode,Fs=32KHz LCD on VDD=3.3V,IDLE mode,LCD off VDD=3.3V, STOP mode RESET, P0, P8 P0, RESET, VDD=3.3V,VIH=3.3/0V Open-drain, VDD=3.3V,VIH=3.3/0V Push-pull, VDD=3.3V ,VIL=0.4V,except P4 Push-pull, P4(high current PMOS), SOUND, VDD=2.7V, IOH=-0.9mA Push-pull, P4(low current PMOS), P8, VDD=2.7V, IOH=-40µA VDD=2.7V,IOL=0.9mA, P4, P8 Open-drain, VDD=3.3V, VO=3.3V P0 RESET VDD=3V, VBZ=1.5V VDD=3V, LCD no load 10.31.2000 30 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P RESET PIN TYPE TYPE RESET-A RESET mask option OSCILLATION PIN TYPE TYPE OSC-B TYPE OSC-H VDD LXIN LXIN Crystal Osc. RC Osc. LXOUT TYPE OSC-G CLK Internal Osc. INPUT PIN TYPE TYPE INPUT-A TYPE INPUT-B WAKEUP function mask option : mask option * This specification are subject to be changed without notice. P0/WAKEUP TYPE INPUT-A 10.31.2000 31 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P I/O PIN TYPE TYPE I/O TYPE I/O-L path B SEL path A Input data mask option Output data latch TYPE I/O Special function control input Output data WAKEUP function mask option TYPE I/O-N TYPE I/O-O path B Input data path A TYPE I/O-N : mask option : mask option Path A : Path B : Output data latch Output data Special function output For set and clear bit of port instructions, data goes through path A from output data latch to CPU. For input and test instructions, data from output pin go through path B to CPU and the output data latch will be set to high. * This specification are subject to be changed without notice. 10.31.2000 32 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT Pad No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SEG35 SEG36 SEG37 SEG38 SEG39 VB VA V5 V4 V3 V2 V1 SEG19 SEG18 SEG17 SEG15 SEG14 SEG13 SEG12 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 SEG7 3 SEG6 4 SEG5 5 SEG4 6 SEG3 7 SEG2 8 SEG1 9 SEG0 10 COM7 11 COM6 12 COM5 13 COM4 14 COM3 15 COM2 16 COM1 17 COM0 18 (0,0) Symbol SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0 COM7 COM6 COM5 COM4 COM3 COM2 37 38 39 40 P8.2 55 SEG34 54 SEG33 53 SEG32 52 SEG31 51 SEG30 50 SEG29 49 SEG28 48 SEG27 47 SEG26 46 SEG25 45 COM24 44 COM23 43 SEG22 42 SEG21 41 SEG20 P8.3 34 35 36 P8.1 32 33 P8.0 29 30 31 P0.3 28 P0.2 27 P0.1 26 P0.0 23 24 25 P4.3 22 P4.2 21 P4.1 BZ2 P4.0 20 VDD BZ1 LXOUT 19 TEST VDD2 LXIN EM73983 CLK 2 RESET 1 SEG8 VSS SEG9 SEG11 SEG10 PAD DIAGRAM SEG16 inary m i l e r P X Y -1400.8 -1400.8 -1400.8 -1400.8 -1400.8 -1400.8 -1400.8 -1400.8 -1400.8 -1400.8 -1400.8 -1400.8 -1400.8 -1400.8 -1400.8 -1400.8 1312.0 1191.4 1070.9 950.4 829.8 709.3 588.7 468.2 347.7 227.1 106.6 -14.0 -134.5 -255.0 -375.6 -496.1 * This specification are subject to be changed without notice. 10.31.2000 33 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P Pad No. 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 Symbol COM1 COM0 VDD2 BZ1 BZ2 VSS RESET CLK TEST LXIN LXOUT VDD P4.0 P4.1 P4.2 P4.3 P0.0 P0.1 P0.2 P0.3 P8.0 P8.1 P8.2 P8.3 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 SEG34 SEG35 SEG36 SEG37 SEG38 X Y -1400.8 -1400.8 -1360.4 -1354.9 -1354.9 -1111.5 -948.7 -828.1 -707.6 -580.4 -459.9 -298.6 -170.6 -48.5 73.6 195.8 317.9 440.1 562.2 684.3 806.5 928.6 1050.7 1172.9 1405.0 1405.0 1405.0 1405.0 1405.0 1405.0 1405.0 1405.0 1405.0 1405.0 1405.0 1405.0 1405.0 1405.0 1405.0 1283.2 1162.7 1042.2 921.6 -616.7 -737.2 -859.4 -1052.0 -1266.7 -1290.1 -1290.1 -1290.1 -1290.1 -1290.1 -1290.1 -1275.5 -1290.1 -1290.1 -1290.1 -1290.1 -1290.1 -1290.1 -1290.1 -1290.1 -1290.1 -1290.1 -1290.1 -1290.1 -434.8 -314.3 -193.7 -73.2 47.4 167.9 288.4 409.0 529.5 650.1 770.6 891.1 1011.7 1132.2 1252.8 1289.5 1289.5 1289.5 1289.5 * This specification are subject to be changed without notice. 10.31.2000 34 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P Pad No. 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 Symbol SEG39 VB VA V5 V4 V3 V2 V1 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 X Y 801.1 680.5 560.0 439.5 318.9 198.4 77.8 -42.7 -163.2 -283.8 -404.3 -524.9 -645.4 -765.9 -886.5 -1007.0 -1127.6 -1248.1 1289.5 1289.5 1289.5 1289.5 1289.5 1289.5 1289.5 1289.5 1289.5 1289.5 1289.5 1289.5 1289.5 1289.5 1289.5 1289.5 1289.5 1289.5 Unit : µm Chip Size : 3150 x 2930 µm Note : For PCB layout,IC substrate must be floated or connected to VSS. * This specification are subject to be changed without notice. 10.31.2000 35 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT INSTRUCTION TABLE inary m i l e r P (1) Data Transfer Mnemonic LDA x LDAM LDAX LDAXI LDH #k LDHL x LDIA #k LDL #k STA x STAM STAMD STAMI STD #k,y STDMI #k THA TLA Object code ( binary ) Operation description Byte 0110 1010 xxxx xxxx 0101 1010 0110 0101 0110 0111 1001 kkkk 0100 1110 xxxx xx00 1101 kkkk 1000 kkkk 0110 1001 xxxx xxxx 0101 1001 0111 1101 0111 1111 0100 1000 kkkk yyyy 1010 kkkk 0111 0110 0111 0100 Acc←RAM[x] Acc ←RAM[HL] Acc←ROM[DP]L Acc←ROM[DP]H,DP+1 HR←k LR←RAM[x],HR←RAM[x+1] Acc←k LR←k RAM[x]←Acc RAM[HL]←Acc RAM[HL]←Acc, LR-1 RAM[HL]←Acc, LR+1 RAM[y]←k RAM[HL]←k, LR+1 Acc←HR Acc←LR 2 1 1 1 1 2 1 1 2 1 1 1 2 1 1 1 Object code ( binary ) Operation description Byte Cycle 2 1 2 2 1 2 1 1 2 1 1 1 2 1 1 1 C - Flag Z Z Z Z Z Z Z Z Z Z Z C C C Flag Z Z Z S C' C' C C - Flag Z Z Z Z Z Z Z Z Z Z Z Z S C' C' C' C' C' C' C' C C C C' S 1 1 1 1 1 1 1 1 1 1 C C' 1 C' 1 1 (2) Rotate Mnemonic RLCA RRCA 0101 0000 0101 0001 ←CF←Acc← →CF→Acc→ 1 1 Cycle 1 1 (3) Arithmetic operation Mnemonic ADCAM ADD #k,y ADDA #k ADDAM ADDH #k ADDL #k ADDM #k DECA DECL DECM INCA Object code ( binary ) 0111 0100 0110 0111 0110 0110 0110 0101 0111 0101 0101 0000 1001 kkkk yyyy 1110 0101 kkkk 0001 1110 1001 kkkk 1110 0001 kkkk 1110 1101 kkkk 1100 1100 1101 1110 Operation description Acc←Acc + RAM[HL] + CF RAM[y]←RAM[y] +k Acc←Acc+k Acc←Acc + RAM[HL] HR←HR+k LR←LR+k RAM[HL]←RAM[HL] +k Acc←Acc-1 LR←LR-1 RAM[HL]←RAM[HL] -1 Acc←Acc + 1 * This specification are subject to be changed without notice. Byte 1 2 2 1 2 2 2 1 1 1 1 Cycle 1 2 2 1 2 2 2 1 1 1 1 10.31.2000 36 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P INCL INCM SUBA #k SBCAM SUBM #k 0111 1110 0101 1111 0110 1110 0111 kkkk 0111 0010 0110 1110 1111 kkkk LR←LR + 1 RAM[HL]←RAM[HL]+1 Acc←k-Acc Acc←RAM[HLl - Acc - CF' RAM[HL]←k - RAM[HL] 1 1 2 1 2 Operation description Byte 1 1 2 1 2 C - Z Z Z Z Z C' C' C C C (4) Logical operation Mnemonic 1110 0110 kkkk 1011 1110 1110 kkkk 1110 0100 kkkk 1000 1110 1100 kkkk 1001 Acc←Acc&k Acc←Acc & RAM[HL] RAM[HL]←RAM[HL]&k Acc←Acc k Acc ←Acc RAM[HL] RAM[HL]←RAM[HL] k Acc←Acc^RAM[HL] 2 1 2 2 1 2 1 Operation description Byte -- 0110 0111 0110 0110 0111 0110 0111 ---- ANDA #k ANDAM ANDM #k ORA #k ORAM ORM #k XORAM Object code ( binary ) Cycle 2 1 2 2 1 2 1 C - Flag Z Z Z Z Z Z Z Z S Z' Z' Z' Z' Z' Z' Z' C Flag Z S (5) Exchange Mnemonic EXA x EXAH EXAL EXAM EXHL x Object code ( binary ) 0110 1000 xxxx xxxx 0110 0110 0110 0100 0101 1000 0100 1100 xxxx xx00 Cycle Acc↔RAM[x] Acc↔HR Acc↔LR Acc↔RAM[HL] LR↔RAM[x], HR↔RAM[x+1] 2 1 1 1 2 2 2 1 - Z Z Z Z 1 1 1 1 2 2 - - 1 Operation description Byte C Flag Z S (6) Branch Mnemonic Object code ( binary ) SBR a 00aa aaaa LBR a SLBR a 1100 aaaa aaaa aaaa 0101 0101 1100 aaaa Cycle If SF=1 then PC←PC12-6.a5-0 else null If SF= 1 then PC←a else null If SF=1 then PC←a else null 1 1 - - 1 2 3 2 3 - - 1 1 Operation description Byte C Flag Z S C C Z Z Z' Z' aaaa aaaa (a:1000~1FFFh) 0101 0111 1100 aaaa aaaa aaaa (a:0000~0FFFh) (7) Compare Mnemonic Object code ( binary ) CMP #k,y 0100 1011 kkkk yyyy CMPA x 0110 1011 xxxx xxxx k-RAM[y] RAM[x]-Acc * This specification are subject to be changed without notice. 2 2 Cycle 2 2 10.31.2000 37 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT inary m i l e r P Mnemonic CMPAM CMPH #k CMPIA #k CMPL #k Object code ( binary ) 0111 0011 0110 1110 1011 kkkk 1011 kkkk 0110 1110 0011 kkkk Operation description Byte RAM[HL] - Acc k - HR k - Acc k-LR 1 2 1 2 Operation description Byte Cycle 1 2 1 2 C Flag Z S C C - Z Z Z Z Z' C Z' C (8) Bit manipulation Mnemonic Object code ( binary ) Cycle C - Flag Z - S 1 1 1 1 1 1 1 1 * * * * * * * S - 1111 00bb 0110 1101 11bb pppp 0110 0000 0110 1100 11bb yyyy 1111 01bb 0110 1101 01bb pppp 0110 0010 0110 1100 01bb yyyy 0110 1100 00bb yyyy 1111 10bb 1111 11bb 0110 1101 00bb pppp 0110 0001 0110 1100 10bb yyyy 0110 1101 10bb pppp RAM[HL]b←0 PORT[p]b←0 PORT[LR3-2+4]LR1-0←0 RAM[y]b←0 RAM[HL]b←1 PORT[p]b←1 PORT[LR3-2+4]LRl-0←1 RAM[y]b←1 SF←RAM[y]b' SF←Accb' SF←RAM[HL]b' SF←PORT[p]b' SF←PORT[LR 3-2 +4]LR1-0' SF←RAM[y]b SF←PORT[p]b 1 2 1 2 1 2 1 2 2 1 1 2 1 2 2 Mnemonic Object code ( binary ) Operation description Byte LCALL a 0100 0aaa aaaa aaaa 2 2 SCALL a 1110 nnnn 1 2 - - - RET 0100 1111 STACK[SP]←PC, SP←SP -1, PC←a STACK[SP]←PC, SP←SP - 1, PC←a, a = 8n + 6 (n =1∼15),0086h (n = 0) SP←SP + 1, PC←STACK[SP] Flag C Z - 1 2 - - - Object code ( binary ) Operation description Byte CLM CLP CLPL CLR SEM SEP SEPL SET TF TFA TFM TFP TFPL TT TTP b p,b y,b b p,b y,b y,b b b p,b y,b p,b 1 2 2 2 1 2 2 2 2 1 1 2 2 2 2 (9) Subroutine Cycle (10) Input/output Mnemonic INA INM OUT OUTA OUTM p p #k,p p p 0110 1111 0100 pppp 0110 1111 1100 pppp 0100 1010 kkkk pppp 0110 1111 000p pppp 0110 1111 100p pppp Acc←PORT[p] RAM[HL]←PORT[p] PORT[p]←k PORT[p]←Acc PORT[p]←RAM[HL] * This specification are subject to be changed without notice. 2 2 2 2 2 Cycle 2 2 2 2 2 C - Flag Z Z - 10.31.2000 S Z' Z' 1 1 1 38 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT (11) Flag manipulation Mnemonic TFCFC TTCFS TZS Object code ( binary ) 0101 0011 0101 0010 0101 1011 inary m i l e r P Operation description Byte SF←CF', CF←0 SF←CF, CF←1 SF←ZF 1 1 1 Operation description Byte Cycle 1 1 1 Flag C 0 1 - Z - S * * * (12) Interrupt control Mnemonic CIL r DICIL r EICIL r EXAE RTI Object code ( binary ) 0110 0011 11rr rrrr 0110 0011 10rr rrrr 0110 0011 01rr rrrr 0111 0101 0100 1101 IL←IL & r EIF←0,IL←IL&r EIF←1,IL←IL&r MASK↔Acc SP←SP+1,FLAG.PC ←STACK[SP],EIF ←1 2 2 2 1 1 Object code ( binary ) Operation description Byte Cycle 2 2 2 1 2 C * Flag Z * S 1 1 1 1 * C - Flag Z - S - C - Flag Z Z Z Z Z Z Z Z Z Z Z - S 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 (13) CPU control Mnemonic NOP 0101 0110 no operation 1 Cycle 1 (14) Timer/Counter & Data pointer & Stack pointer control Mnemonic Object code ( binary ) Operation description LDADPL 0110 1010 1111 1100 Acc←[DP]L LDADPM 0110 1010 1111 1101 Acc←[DP]M LDADPH 0110 1010 1111 1110 Acc←[DP]H LDASP 0110 1010 1111 1111 Acc←SP LDATAL 0110 1010 1111 0100 Acc←[TA]L LDATAM 0110 1010 1111 0101 Acc←[TA]M LDATAH 0110 1010 1111 0110 Acc←[TA]H LDATBL 0110 1010 1111 1000 Acc←[TB]L LDATBM 0110 1010 1111 1001 Acc←[TB]M LDATBH 0110 1010 1111 1010 Acc←[TB]H STADPL 0110 1001 1111 1100 [DP]L←Acc STADPM 0110 1001 1111 1101 [DP]M←Acc STADPH 0110 1001 1111 1110 [DP]H←Acc STASP 0110 1001 1111 1111 SP←Acc STATAL 0110 1001 1111 0100 [TA]L←Acc STATAM 0110 1001 1111 0101 [TA]M←Acc STATAH 0110 1001 1111 0110 [TA]H←Acc STATBL 0110 1001 1111 1000 [ TB]L←Acc STATBM 0110 1001 1111 1001 [TB]M←Acc STATBH 0110 1001 1111 1010 [TB]H←Acc * This specification are subject to be changed without notice. Byte 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Cycle 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 10.31.2000 39 EM73983 4-BIT MICRO-CONTROLLER FOR LCD PRODUCT **** SYMBOL DESCRIPTION Symbol HR PC SP ACC CF SF IL PORT[p] ΤΒ RAM[x] ROM[DP]H [DP]M [TA]L([TB]L) [TA]H([TB]H) LR3-2 PC12-6 ↔ -- #k y b inary m i l e r P Description Symbol H register Program counter Stack pointer Accumulator Carry flag Status flag Interrupt latch Port ( address : p ) Timer/counter B Data memory (address : x ) High 4-bit of program memory Middle 4-bit of data pointer register Low 4-bit of timer/counter A (timer/counter B) register High 4-bit of timer/counter A (timer/counter B) register Bit 3 to 2 of LR LR DP STACK[SP] FLAG ZF EI MASK ΤΑ RAM[HL] ROM[DP]L [DP]L [DP]H [TA]M([TB]M) Bit 12 to 6 of program counter Exchange Substraction Logic OR Inverse operation 4-bit immediate data 4-bit zero-page address Bit address ← + & ^ . x p r LR 1-0 a5-0 * This specification are subject to be changed without notice. Description L register Data pointer Stack specified by SP All flags Zero flag Enable interrupt register Interrupt mask Timer/counter A Data memory (address : HL ) Low 4-bit of program memory Low 4-bit of data pointer register High 4-bit of data pointer register Middle 4-bit of timer/counter A (timer/counter B) register Contents of bit assigned by bit 1 to 0 of LR Bit 5 to 0 of destination address for branch instruction Transfer Addition Logic AND Logic XOR Concatenation 8-bit RAM address 4-bit or 5-bit port address 6-bit interrupt latch 10.31.2000 40