FILTRONIC FMA500

FMA500
Preliminary Data Sheet
OC-192 MODULATOR PRE-DRIVER AMPLIFIER
•
FEATURES
♦
♦
♦
♦
♦
•
DC – 23 GHz Frequency Bandwidth
13 dB Small Signal Gain
4 Vpp Output Voltage
-12 dB input/output return loss
Chip Size: 1.18 x 1.50 mm
DESCRIPTION AND APPLICATIONS
The Filtronic Solid State FMA500 is a high-gain pre-driver pHEMT amplifier that operates from DC
to 23 GHz. This five-stage travelling wave amplifier provides 13 dB nominal small signal gain and
4 V peak-to-peak NRZ output at bit rates to 12.5 Gb/sec. The FMA500 is designed as the pre-driver
stage for OC-192 MZ modulator driver amplifiers for optical data communication applications, and
can be cascaded with the FMA501 Driver MMIC to provide 30 dB of voltage gain. The FMA500
can also be used as an EA driver amplifier or as a transimpedance amplifier (TIA) for photoreceiver
applications.
•
ELECTRICAL SPECIFICATIONS @ TAmbient = 25°C
(VDD = +4.0V, VGG = -3.0V; VGC = +1.5V; ZIN = ZOUT = 50Ω)
Parameter
Symbol
3dB Operating Bandwidth
BW
23
GHz
Small Signal Gain
S21
13
dB
Operating Current
IOP
100
mA
Input Return Loss
S11
-12
dB
Output Return Loss
S22
-12
dB
Gain Control
GC
VGC = 0V to 1.5V
6
dB
Group Delay Variation
∆τgrp
Over Bandwidth
±20
ps
Rise/Fall time, 20%-80%
τR/F
Output Voltage at Saturation
VOUT
10Gb/sec, NRZ, VIN = 2Vpp
4
V
Saturated Output Power
PSAT
VIN = 2Vpp
20
dBm
Phone: (408) 988-1845
Fax: (408) 970-9950
Test Conditions
Min
Typ
20
http:// www.filss.com
Max
30
Units
ps
Revised: 3/15/02
Email: [email protected]
FMA500
Preliminary Data Sheet
OC-192 MODULATOR PRE-DRIVER AMPLIFIER
•
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Test Conditions
Drain Voltage
VDD
Operating Current
Min
Max
Units
TAmbient = 22 ± 3 °C
5.0
V
IOP
TAmbient = 22 ± 3 °C
150
mA
RF Input Power
PIN
TAmbient = 22 ± 3 °C
12
dBm
Channel Operating Temperature
TCH
TAmbient = 22 ± 3 °C
150
ºC
Storage Temperature
Maximum Assembly Temperature
(1 min. max.)
TSTG
—
165
ºC
TMAX
—
300
ºC
-65
Notes:
• Operating conditions that exceed the Absolute Maximum Ratings could result in permanent damage to the device.
• Recommended Continuous Operating Limits should be observed for reliable device operation.
• This PHEMT is susceptible to damage from Electrostatic Discharge. Proper precautions should be used when handling these
devices.
•
MEASURED PERFORMANCE: 10 Gb/s NRZ Eye Test
(VDD = +4.0V, VGG = -3.0V; VGC = +1.5V; ZIN = ZOUT = 50Ω)
Phone: (408) 988-1845
Fax: (408) 970-9950
http:// www.filss.com
Revised: 3/15/02
Email: [email protected]
Preliminary Data Sheet
FMA500
OC-192 MODULATOR PRE-DRIVER AMPLIFIER
•
ASSEMBLY DIAGRAM
GND
Chip capacitor: 100nF
VDD=3~5V
Inductor for
drain = 300uH
Gate bias: VGG = -3.0 V
Gain control: VGC = +1.5 V
Notes:
• Apply VGG first, then VGC and VDD.
• Disconnect VGC first, then VDD and VGG when turning off.
• Recommended lead bond technique is thermocompression wedge bonding with 0.001” (25µm) diameter wire. The
bond tool force shall be 35-38 gram. Bonding stage temperature shall be 230-240°C, heated tool (150-160°C) is
recommended. Ultrasonic bonding is not recommended.
• The recommended die attach is Ablebond silver epoxy, the stabilize bake temperature is set at 150°C for 45 minutes.
• Bond on bond or stitch bonds acceptable.
• Conductor over conductor acceptable. Conductors must not short.
Phone: (408) 988-1845
Fax: (408) 970-9950
http:// www.filss.com
Revised: 3/15/02
Email: [email protected]
Preliminary Data Sheet
FMA500
OC-192 MODULATOR PRE-DRIVER AMPLIFIER
•
MECHANICAL OUTLINE
Notes:
• All units are in microns (µm).
• All pads are 100 X 100 µm2.
•
HANDLING PRECAUTIONS
To avoid damage to the devices care should be exercised during handling. Proper Electrostatic
Discharge (ESD) precautions should be observed at all stages of storage, handling, assembly, and
testing. These devices should be treated as Class 1A (0-500 V). Further information on ESD control
measures can be found in MIL-STD-1686 and MIL-HDBK-263.
All information and specifications are subject to change without notice.
Phone: (408) 988-1845
Fax: (408) 970-9950
http:// www.filss.com
Revised: 3/15/02
Email: [email protected]