SN74ALB16244 16-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCBS647C – AUGUST 1995 – REVISED JULY 1997 D D D D D D D DGG OR DL PACKAGE (TOP VIEW) Member of the Texas Instruments Widebus Family State-of-the-Art Advanced Low-Voltage BiCMOS (ALB) Technology Design for 3.3-V Operation Schottky Diodes on All Inputs to Eliminate Overshoot and Undershoot Industry Standard ’16244 Pinout Distributed VCC and GND Pin Configuration Minimizes High-Speed Switching Noise Flow-Through Architecture Optimizes PCB Layout Package Options Include Plastic 300-mil Shrink Small-Outline (DL) and Thin Shrink Small-Outline (DGG) Packages 1OE 1Y1 1Y2 GND 1Y3 1Y4 VCC 2Y1 2Y2 GND 2Y3 2Y4 3Y1 3Y2 GND 3Y3 3Y4 VCC 4Y1 4Y2 GND 4Y3 4Y4 4OE description The SN74ALB16244 16-bit buffer and line driver is designed for high-speed, low-voltage (3.3-V) VCC operation. This device is intended to replace the conventional driver in any speed-critical path. The small propagation delay is achieved using a unity gain amplifier on the input and feedback resistors from input to output, which allows the output to track the input with a small offset voltage. 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 17 32 18 31 19 30 20 29 21 28 22 27 23 26 24 25 2OE 1A1 1A2 GND 1A3 1A4 VCC 2A1 2A2 GND 2A3 2A4 3A1 3A2 GND 3A3 3A4 VCC 4A1 4A2 GND 4A3 4A4 3OE The device can be used as four 4-bit buffers, two 8-bit buffers, or one 16-bit buffer. This device provides true outputs and symmetrical active-low output-enable (OE) inputs. The SN74ALB16244 is characterized operation from –40°C to 85°C. for FUNCTION TABLE (each buffer) INPUTS OE A OUTPUT Y L H H L L L H X Z Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus is a trademark of Texas Instruments Incorporated. Copyright 1997, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN74ALB16244 16-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCBS647C – AUGUST 1995 – REVISED JULY 1997 logic symbol† 1OE 2OE 1 EN1 48 25 3OE 4OE 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 3A1 3A2 3A3 3A4 4A1 4A2 4A3 4A4 24 EN2 EN3 EN4 47 1 1 46 3 44 5 43 6 41 40 1 2 8 9 38 11 37 12 36 13 35 1 3 14 33 16 32 17 30 19 1 4 29 20 27 22 26 23 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 2 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 3Y1 3Y2 3Y3 3Y4 4Y1 4Y2 4Y3 4Y4 SN74ALB16244 16-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCBS647C – AUGUST 1995 – REVISED JULY 1997 logic diagram (positive logic) 1OE 1A1 1A2 1A3 1A4 2OE 2A1 2A2 2A3 2A4 1 3OE 47 2 46 3 44 5 43 6 1Y1 3A1 1Y2 3A2 1Y3 3A3 1Y4 3A4 48 4OE 41 8 40 9 38 11 37 12 2Y1 4A1 2Y2 4A2 2Y3 4A3 2Y4 4A4 25 36 13 35 14 33 16 32 17 3Y1 3Y2 3Y3 3Y4 24 30 19 29 20 27 22 26 23 4Y1 4Y2 4Y3 4Y4 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.6 V Input voltage range, VI: Except I/O ports (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 4.6 V I/O ports (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Output voltage range, VO (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous current through each VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA Package thermal impedance, θJA (see Note 3): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89°C/W DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. This value is limited to 4.6 V maximum. 3. The package thermal impedance is calculated in accordance with JESD 51. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN74ALB16244 16-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCBS647C – AUGUST 1995 – REVISED JULY 1997 recommended operating conditions MIN MAX 3 3.6 V High-level output current –25 mA Low-level output current 25 mA 5 ns/V 85 °C VCC IOH† Supply voltage IOL† ∆t/∆v Input transition rise or fall rate Outputs enabled TA Operating free-air temperature † Refer to Figures 1 and 2 for typical I/O ranges. –40 UNIT electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK II TEST CONDITIONS Data inputs VCC = 3 V II = 18 mA II = –18 mA Control inputs VCC = 3.6 V, VI = VCC or GND 3.6 OE low MAX UNIT VCC–1.2 –1.2 V ±10 µA 0.6 mA 25 µA 0.4 OE high VCC = 3 3.6 6V OE low VI = 0 –0.8 –1 mA –60 µA 0.6 20 µA –0.1 –50 µA 3.7 5.6 mA 0.8 mA 600 µA OE high IOZH IOZL VCC = 3.6 V, VCC = 3.6 V, VO = 3 V VO = 0.5 V ICC/buffer ICCZ VCC = 3.6 V, VCC = 3.6 V, IO = 0, VI = VCC or GND Control inputs = VCC or GND ∆ICC§ VCC = 3 V to 3.6 V, One input at VCC – 0.6 V, Other inputs at VCC or GND Ci VI = 3 V or 0 VO = 3 V or 0 Co TYP‡ –0.9 VI = VCC Data inputs MIN 4.5 pF 5.5 pF ‡ All typical values are at VCC = 3.3 V, TA = 25°C. § This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 3) FROM (INPUT) TO (OUTPUT) tpd A Y 0.6 1.3 2 ns ten OE Y 1.3 2.5 4.7 ns tdis OE Y 1.8 2.8 4.2 ns ‡ All typical values are at VCC = 3.3 V, TA = 25°C. 4 VCC = 3.3 V ± 0.3 V MIN TYP‡ MAX PARAMETER POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 UNIT SN74ALB16244 16-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCBS647C – AUGUST 1995 – REVISED JULY 1997 OUTPUT VOLTAGE HIGH vs INPUT VOLTAGE VOH – Output Voltage – V 3.5 3 2.5 –100 µA –25 mA –6 mA 2 1.5 1.5 2 2.5 3 3.5 4 VI – Input Voltage – V Figure 1. VOH Over Recommended Free-Air Temperature Range OUTPUT VOLTAGE LOW vs INPUT VOLTAGE 2 VOL – Output Voltage – V 1.5 25 mA 1 100 µA 0.5 6 mA 0 0 0.5 1 1.5 2 VI – Input Voltage – V Figure 2. VOL Over Recommended Free-Air Temperature Range POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN74ALB16244 16-BIT BUFFER/DRIVER WITH 3-STATE OUTPUTS SCBS647C – AUGUST 1995 – REVISED JULY 1997 PARAMETER MEASUREMENT INFORMATION 6V S1 500 Ω From Output Under Test Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 6V GND LOAD CIRCUIT tw 3V 3V Timing Input 0V 0V VOLTAGE WAVEFORMS PULSE DURATION th 3V Data Input 1.5 V 1.5 V 0V 3V Output Control (low-level enabling) VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 1.5 V 1.5 V 1.5 V 0V tPZL 3V 1.5 V 0V tPLH Output 1.5 V 1.5 V tsu Input 1.5 V Input Output Waveform 1 S1 at 6 V (see Note B) 3V 1.5 V VOL + 0.3 V tPZH tPHL VOH 1.5 V tPLZ 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES VOL tPHZ Output Waveform 2 S1 at GND (see Note B) 1.5 V VOH VOH – 0.3 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 Ω, tr 2.5 ns, tf 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. v Figure 3. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 v v IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated