TI TPS53311RGTT

TPS53311
www.ti.com
SLUSA41 – JUNE 2010
3-A Step-Down Regulator with Integrated Switcher
Check for Samples: TPS53311
FEATURES
LOW VOLTAGE APPLICATIONS
•
•
•
1
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
TI Proprietary Integrated MOSFET and
Packaging Technology
Continuous 3-A Output Current
Supports All MLCC Output Capacitor
Supports Skip Mode for Light Load Control
Optimized Efficiency at Light and Heavy Loads
Voltage Mode Control
Supports Master-Slave Interleaved Operation
Synchronization up to ±20% of Nominal
Frequency
Conversion Voltage Range Between 2.9 V and
6.0 V
Soft-Stop Output Discharge During Disable
Adjustable Output Voltage Ranging Between
0.6 V and 0.84 V × VIN
Overcurrent, Overvoltage and
Over-Temperature Protection
Small 3 × 3 , 16-Pin QFN Package
Open-Drain Power Good Indication
Internal Boot Strap Switch
Low RDS(on), 24 mΩ with 3.3-V Input and 19-mΩ
with 5-V Input
5-V Step-down Rail
3.3-V Step-down Rail
DESCRIPTION
TPS53311 is a fully integrated synchronous buck
regulator using the TI's proprietary SmoothPMW™
voltage mode control. It is designed for 3.3-V and 5-V
step-downs where system size is at a premium, and
where performance and optimized component lists
are mandatory.
The TPS53311 features a 1.1-MHz switching
frequency, SKIP mode operation support, pre-bias
startup, internal softstart, output soft discharge,
internal VBST switch, power good, EN/input UVLO,
overcurrent,
overvoltage,
undervoltage
and
over-temperature protections and all ceramic output
capacitor support. It supports supply voltage from
2.9 V to 3.5 V and conversion voltage from 2.9 V to
6.0 V, and output voltage is adjustable from 0.6 V to
0.84 V × VIN.
The TPS53311 is available in the 3 mm × 3 mm
16-pin QFN package (Green RoHs compliant and Pb
free) with TI proprietary Integrated MOSFET and
packaging technology and operates between –40°C
and 85°C.
TYPICAL APPLICATION CIRCUIT
Output All MLCCs
VIN
2.9 V to 6 V
VDD
2.9 V to 3.5 V
13
14
5
VIN
VIN
6
7
CBST
SW SW SW
12 VDD
VBST
4
PGD
3
VIN
11 AGND
SYNC
2
SYNC
EN
1
EN
8
PS
TPS53311
PGD
FB 10
PGND PGND
15
Pad
COMP
9
16
UDG-10027
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
SmoothPMW is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010, Texas Instruments Incorporated
TPS53311
SLUSA41 – JUNE 2010
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION
TA
PACKAGE
–40°C to
85°C
Plastic QFN
(RGT)
ORDERABLE DEVICE
NUMBER
PINS
OUTPUT SUPPLY
MINIMUM
QUANTITY
TPS53311RGTR
16
Tape and reel
3000
TPS53311RGTT
16
Mini reel
250
ECO PLAN
Green (RoHS and no Pb/Br)
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
VALUE
MIN
Input voltage range
VIN, EN
–0.3
7
VBST
–0.3
17
VBST(with respect to SW)
–0.3
7
FB, PS, VDD
–0.3
3.7
–0.3
7
–3
10
DC
SW
Output voltage range
Electrostatic Discharge
UNIT
MAX
Pulse < 20ns, E= 5mJ
PGD
–0.3
7
COMP, SYNC
–0.3
3.7
PGND
–0.3
V
V
0.3
Human Body Model (HBM)
2000
Charged Device Model (CDM)
V
500
Ambient temperature
TA
–40
85
˚C
Storage temperature
Tstg
–55
150
˚C
Junction temperature
TJ
–40
150
˚C
300
˚C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
(1)
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
VALUE
MIN
Input voltage range
3.3
3.5
2.9
VDD
2.9
VBST
–0.1
13.5
VBST(with respect to SW)
–0.1
6
EN
–0.1
6
FB, PS
–0.1
3.5
–1
6.5
–0.1
6
COMP, SYNC
–0.1
3.5
PGND
–0.1
0.1
–40
125
Submit Documentation Feedback
UNIT
6
PGD
Junction temperature range, TJ
2
MAX
VIN
SW
Output voltage range
NOM
V
V
°C
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
TPS53311
www.ti.com
SLUSA41 – JUNE 2010
PACKAGE DISSIPATION RATINGS
PACKAGE
THERMAL IMPEDANCE,
JUNCTION TO THERMAL PAD
THERMAL IMPEDANCE,
JUNCTION TO CASE
THERMAL IMPEDANCE,
JUNCTION TO AMBIENT
16-Pin Plastic QFN (RGT)
5°C/W
16°C/W
40°C/W
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
3
TPS53311
SLUSA41 – JUNE 2010
www.ti.com
ELECTRICAL CHARACTERISTICS
over recommended free-air temperature range, VIN = 3.3 V, VVDD = 3.3 V, PGND = GND (Unless otherwise noted).
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY: VOLTAGE, CURRENTS, and UVLO
VIN
VIN supply voltage
Nominal input voltage range
IVINSDN
VIN shutdown current
EN = 'LO'
2.9
VUVLO
VIN UVLO threshold
Ramp up; EN = 'HI'
2.8
V
VUVLOHYS
VIN UVLO hysteresis
VIN UVLO Hysteresis
130
mV
VDD
Internal circuitry supply voltage
Nominal 3.3-V input voltage range
IDDSDN
VDD shut down current
EN = 'LO'
IDD
Standby current
VDDUVLO
3.3V UVLO threshold
VDDUVLOHYS
3.3V UVLO hysteresis
2.9
6.0
V
3
µA
3.3
3.5
V
5
µA
EN = 'HI', no switching
2.2
3.5
mA
Ramp up; EN =’HI’
2.8
V
75
mV
VOLTAGE FEEDBACK LOOP: VREF AND ERROR AMPLIFIER
VVREF
VREF
Internal precision reference voltage
0.6
0°C ≤ TA ≤ 85°C
V
–1%
1%
–1.25%
1.25%
TOLVREF
VREF Tolerance
UGBW (1)
Unity gain bandwidth
14
MHz
AOL (1)
Open loop gain
80
dB
IFBINT
IEAMAX
(1)
SR (1)
–40°C ≤ TA ≤ 85°C
FB input leakage current
Sourced from FB pin
Output sinking and sourcing
current
CCOMP = 20 pF
30
Slew rate
nA
5
mA
5
V/µs
OCP: OVER CURRENT AND ZERO CROSSING
IOCPL
Overcurrent limit on upper FET
When IOUT exceeds this threshold for 4
consecutive cycles. VIN=3.3 V,
VOUT=1.5 V with 1-µH inductor, TA = 25°C
4.2
4.5
4.8
A
IOCPH
One time overcurrent latch off
on the lower FET
Immediately shut down when sensed current
reach this value. VIN=3.3 V,
VOUT=1.5 V with 1-µH inductor, TA = 25°C
4.8
5.1
5.5
A
VZXOFF (1)
Zero crossing comparator
internal offset
PGND – SW, SKIP mode
–4.5
–3.0
–1.5
mV
PROTECTION: OVP, UVP, PGD, AND INTERNAL THERMAL SHUTDOWN
VOVP
Overvoltage protection
threshold voltage
Measured at FB wrt. VREF
114%
117%
120%
VUVP
Undervoltage protection
threshold voltage
Measured at FB wrt. VREF
80%
83%
86%
VPGDL
PGD low threshold
Measured at FB wrt. VREF
80%
83%
86%
VPGDU
PGD upper threshold
Measured at FB wrt. VREF.
114%
117%
120%
VINMINPG
Minimum Vin voltage for valid
PGD at start up.
Measured at VIN with 1-mA (or 2-mA) sink
current on PGD pin at start up
THSD (1)
Thermal shutdown
Latch off controller, attempt soft-stop
THSDHYS (1)
Thermal Shutdown hysteresis
Controller restarts after temperature has dropped
(1)
4
1
130
140
40
V
150
°C
°C
Ensured by design. Not production tested.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
TPS53311
www.ti.com
SLUSA41 – JUNE 2010
ELECTRICAL CHARACTERISTICS (continued)
over recommended free-air temperature range, VIN = 3.3 V, VVDD = 3.3 V, PGND = GND (Unless otherwise noted).
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
0.2
0.4
V
0
2
µA
LOGIC PINS: I/O VOLTAGE AND CURRENT
VPGPD
PGD pull down voltage
Pull-down voltage with 4-mA sink current
IPGLK
PGD leakage current
Hi-Z leakage current, apply 3.3-V in off state
RENPU
Enable pull up resistor
VENH
EN logic high threshold
VENHYS
EN hysteresis
1.35
1.10
Level 1 to level 2
PSTHS
PS mode threshold voltage
–2
(2)
MΩ
1.18
1.30
V
0.18
0.24
V
0.12
Level 2 to level 3
0.4
Level 3 to level 4
0.8
Level 4 to level 5
1.4
Level 5 to level 6
V
2.2
IPS
PS source
10-µA pull-up current when enabled.
8
fSYNCSL
Slave SYNC frequency range
Versus nominal switching frequency
–20%
PWSYNC
SYNC low pulse width
110
ns
ISYNC
SYNC pin sink current
10
µA
1.0
V
0.5
V
(3)
VSYNCTHS
VSYNCHYS
(3)
SYNC threshold
Falling edge
SYNC hysteresis
10
12
µA
20%
BOOT STRAP: VOLTAGE AND LEAKAGE CURRENT
IVBSTLK
VBST leakage current
VIN = 3.3V, VVBST = 6.6 V, TA = 25°C
1
µA
TIMERS: SS, FREQUENCY, RAMP, ON-TIME AND I/O TIMING
tSS_1
Delay after EN asserting
EN = 'HI', master or HEF mode
0.2
ms
tSS_2
Delay after EN asserting
EN = 'HI', slave waiting time
0.5
ms
tSS_3
Soft-start ramp-up time
Rising from VSS = 0 V to VSS = 0.6 V
0.4
ms
tPGDENDLY
PGD startup delay time
Rising from VSS = 0 V to VSS = 0.6 V,
from VSS reaching 0.6 V to VPGD going high
0.4
ms
tOVPDLY
Overvoltage protection delay
time
Time from FB out of +20% of VREF to OVP fault
tUVPDLY
Undervoltage protection delay
time
Time from FB out of -20% of VREF to UVP fault
fSW
Switching frequency control
Forced CCM mode
Ramp amplitude
tMIN(off)
DMAX
RSFTSTP
(2)
(3)
(3)
Minimum OFF time
Maximum duty cycle, FCCM
mode and DE mode
Maximum duty cycle, HEF
mode
Soft-discharge transistor
resistance
1.0
1.7
2.5
11
0.99
2.9 V < VIN < 6.0 V
1.1
µs
1.21
VIN/4
100
140
HEF mode
175
250
89%
75%
81%
MHz
V
FCCM mode or DE mode
84%
µs
ns
fSW = 1.1 MHz, 0°C ≤ TA ≤ 85°C
VEN = Low, VIN = 3.3 V, VOUT = 0.5 V
60
Ω
See PS pin description for levels.
Ensured by design. Not production tested.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
5
TPS53311
SLUSA41 – JUNE 2010
www.ti.com
EN
1
SYNC
2
PGND
PGND
VIN
VIN
RGT Package
(Top View)
16
15
14
13
12
VDD
11
AGND
TPS53311
VBST
4
9
COMP
5
6
7
8
PS
FB
SW
10
SW
3
SW
PGD
PIN FUNCTIONS
I/O (1)
PIN
DESCRIPTION
NAME
NO.
AGND
11
G
Device analog ground terminal.
COMP
9
O
Error amplifier compensation terminal. Type III compensation method is recommended for stability.
EN
1
I
Enable. Internally pulled up to VDD with a 1.35-MΩ resistor.
FB
10
I
Voltage feedback. Use for OVP, UVP and PGD determination.
PGD
3
O
Power good output flag. Open drain output. Pull up to an external rail via a resistor.
P
IC power GND terminal.
PGND
15
16
PS
8
I
Mode configuration pin (with 10 µA current):
Connecting to ground: Forced CCM slave
Pulled high or floating (internal pulled high): Forced CCM master
Connect with 24.3 kΩ to GND: DE slave
Connect with 57.6 kΩ to GND: HEF mode
Connect with 105 kΩ to GND : reserved mode
Connect with 174 kΩ to GND: DE master.
SYNC
2
B
Synchronization signal for input interleaving. Master SYNC pin sends out 180° out-of-phase signal to slave
SYNC. SYNC frequency must be within ±20% of slave nominal frequency.
B
Output inductor connection to integrated power devices.
5
SW
6
7
VBST
4
P
Supply input for high-side MOSFET (bootstrap terminal). Connect capacitor from this pin to SW terminal.
VDD
12
P
Input bias supply for analog functions.
P
Gate driver supply and power conversion voltage.
VIN
(1)
6
13
14
I – Input; B – Bidirectional; O – Output; G – Ground; P – Supply (or Ground)
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
TPS53311
www.ti.com
SLUSA41 – JUNE 2010
FUNCTIONAL BLOCK DIAGRAM
0.6 V–17%
UV/OV
Threshold
Generation
0.6 V
+
0.6 V+17%
VIN
14
13
+
OV
Control
Logic
HDRV
PWM
+
COMP
9
E/A
0.6 V
+
Ramp
4
VBST
5
SW
6
SW
7
SW
VIN UVLO
UV
FB 10
VIN
+
XCON
PWM
LL One-Shot
Overtemp
VOUT Discharge
SS
LDRV
15 PGND
16 PGND
OSC
Enable
Control
OCP Logic
Mode
Scanner
VDD UVLO
12 VDD
2
1
8
3
11
SYNC
EN
PS
PGD
AGND
TPS53311
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
UDG-10028
7
TPS53311
SLUSA41 – JUNE 2010
www.ti.com
TYPICAL CHARACTERISTICS
Inductor IN06142 (1 µH, 5.4 mΩ) is used.
h – Efficiency – %
96
96
VOUT = 2.5 V
VOUT = 2.5 V
94
94
92
92
90
90
88
88
VOUT = 1.2 V
86
VOUT = 1.2 V
86
VOUT = 1.5 V
VOUT = 1.5 V
VOUT = 1.8 V
VOUT = 1.8 V
84
84
Skip Mode
VIN = 3.3 V
82
FCCM Mode
VIN = 3.3 V
82
80
80
0
0.5
1.0
1.5
2.0
2.5
0
3.0
0.5
IOUT – Output Current – A
2.0
2.5
3.0
Figure 2. Efficiency vs. Output Current, FCCM, VIN = 3.3 V
96
96
VOUT = 2.5 V
VOUT = 2.5 V
94
94
92
92
90
88
VOUT = 1.5 V
86
VOUT = 1.8 V
VOUT = 1.2 V
84
h – Efficiency – %
h – Efficiency – %
1.5
IOUT – Output Current – A
Figure 1. Efficiency vs. Output Current, Skip Mode, VIN =
3.3 V
90
88
VOUT = 1.5 V
86
VOUT = 1.8 V
VOUT = 1.2 V
84
Skip Mode
VIN = 5 V
82
FCCM Mode
VIN = 5 V
82
80
80
0
0.5
1.0
1.5
2.0
2.5
3.0
0
IOUT – Output Current – A
0.5
1.0
1.5
2.0
2.5
3.0
IOUT – Output Current – A
Figure 3. Efficiency vs. Output Current, Skip Mode, VIN = 5
V
8
1.0
Figure 4. Efficiency vs. Output Current, FCCM, VIN = 5 V
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
TPS53311
www.ti.com
SLUSA41 – JUNE 2010
TYPICAL CHARACTERISTICS (continued)
Inductor IN06142 (1 µH, 5.4 mΩ) is used.
0.5
0.620
0.615
VFB – Feedback Voltage – V
0.3
Output Voltage Change (%)
0.610
0.605
0.600
0.595
0.590
0.1
– 0.1
– 0.3
VIN = 5.0 V
VIN = 3.3 V
0.585
0.580
–40 –25 –10
– 0.5
5
20
35
50
65
80
0
95 110 125
0.5
1.0
2.0
2.5
3.0
Output Current (A)
TA – Ambient Temperature – °C
Figure 5. Feedback Voltage vs. Ambient Temperature
Figure 6. Output Voltage Change vs. Output Current
10 k
10 k
Mode
FCCM
HEF
DE
Mode
FCCM
HEF
DE
1000
Frequency (kHz)
Frequency (kHz)
1.5
100
1000
100
VIN = 3.3 V
10
0.01
0.1
1.0
VIN = 5.0 V
10
10
0.01
Output Current (A)
0.1
1.0
10
Output Current (A)
Figure 7. Frequency vs. Output Current at VIN = 3.3 V
Figure 8. Frequency vs. Output Current at VIN = 5.0 V
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
9
TPS53311
SLUSA41 – JUNE 2010
www.ti.com
TYPICAL CHARACTERISTICS (continued)
Inductor IN06142 (1 µH, 5.4 mΩ) is used.
HEF Mode
VIN = 3.3 V
IOUT = 0 A
HEF Mode
VIN = 3.3 V
IOUT = 0 A
EN (5 V/div)
EN (5 V/div)
0.5 V pre-biased
VOUT (1 V/div)
VOUT (1 V/div)
PGD (5 V/div)
PGD (5 V/div)
t – Time – 200 ms/div
t – Time – 200 ms/div
Figure 9. Normal Start Up Waveform
Figure 10. Pre-Bias Start Up Waveform
90
80
EN (5 V/div)
HEF Mode
VIN = 3.3 V
IOUT = 0 A
No Air Flow
VOUT (1 V/div)
PGD (5 V/div)
Temperature (C)
70
60
50
40
30
t – Time – 4 ms/div
VIN = 3.3 V @
VOUT = 0.6 V
VOUT = 1.2 V
VOUT = 1.8 V
VOUT = 2.5 V
20
0.0
0.5
VIN = 5 V @
VOUT = 0.6 V
VOUT = 1.2 V
VOUT = 1.8 V
VOUT = 2.5 V
VOUT = 3.3 V
1.0
1.5
2.0
2.5
3.0
Output Current (A)
Figure 11. Soft-Stop Waveform
10
Submit Documentation Feedback
Figure 12. Safe Operating Area
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
TPS53311
www.ti.com
SLUSA41 – JUNE 2010
APPLICATION INFORMATION
APPLICATION CIRCUIT DIAGRAM
L1
1 mH
Output all MLCCs
VIN
C5
22 mF
R6
2.2 W
C6
0.1 mF
C8
1 mF
13
14
VIN
VIN
5
6
COUT
3 x 22 mF
7
C4
VIN
0.1 mF
SW SW SW
12 VDD
VBST
4
PGD
3
R7
20 kW
11 AGND
TPS53311
SYNC
EN
2
SYNC
1
EN
8
PS
FB 10
C2 22 nF
R5
57.6 kW
PGD
PGND PGND COMP
15
R3
20 W
R4
4.02 kW
R1
9
4.02 kW
R2
4.02 kW
C3
100 pF
16
C1
2.2 nF
UDG-10029
Figure 13. Typical 3.3-V input Application Circuit Diagram
OVERVIEW
The TPS53311 is a high-efficiency switching regulator with two integrated N-channel MOSFETs and is capable
of delivering up to 3 A of load current. The TPS53311 provides output voltage between 0.6 V and 0.84 × VIN from
2.9 V to 6.0 V wide input voltage range.
This device employs five operation modes to fit various application needs. The master/slave mode enables a
two-phase interleaved operation to reduce input ripple. The skip mode operation provides reduced power loss
and increases the efficiency at light load. The unique, patented PWM modulator enables smooth light load to
heavy load transition while maintaining fast load transient.
OPERATION MODE
The TPS53311 offers five operation modes determined by the PS pin connections listed in Table 1.
Table 1. Operation Mode Selection
PS PIN CONNECTION
OPERATION MODE
AUTO-SKIP AT LIGHT LOAD
GND
FCCM Slave
24.3 kΩ to GND
DE Slave
√
57.6 kΩ to GND
HEF Mode
√
174 kΩ to GND
DE Master
√
Floating or pulled to VDD
FCCM Master
MASTER/SLAVE SUPPORT
Slave
Slave
Master
Master
In forced continuous conduction mode (FCCM), the high-side FET is ON during the on-time and the low-side FET
is ON during the off-time. The switching is synchronized to the internal clock thus the switching frequency is
fixed.
In diode emulation mode (DE), the high-side FET is ON during the on-time and low-side FET is ON during the
off-time until the inductor current reaches zero. An internal zero-crossing comparator detects the zero crossing of
inductor current from positive to negative. When the inductor current reaches zero, the comparator sends a
signal to the logic control and turns off the low-side FET.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
11
TPS53311
SLUSA41 – JUNE 2010
www.ti.com
When the load is increased, the inductor current is always positive and the zero-crossing comparator does not
send a zero-crossing signal. The converter enters into continuous conduction mode (CCM) when no
zero-crossing is detected for two consecutive PWM pulses. The switching synchronizes to the internal clock and
the switching frequency is fixed.
In high-efficiency mode (HEF), the operation is the same as diode emulation mode at light load. However, the
converter does not synchronize to the internal clock during CCM. Instead, the PWM modulator determines the
switching frequency.
LIGHT LOAD OPERATION
In skip modes (DE and HEF) when the load
inductor current becomes negative by the end
turned off when the inductor current reaches
increased compared to the normal PWM mode
loss is reduced, thereby improving efficiency.
current is less than one-half of the inductor peak current, the
of off-time. During light load operation, the low-side MOSFET is
zero. The energy delivered to the load per switching cycle is
operation and the switching frequency is reduced. The switching
In both DE and HEF mode, the switching frequency is reduced in discontinuous conduction mode (DCM). When
the load current is 0 A, the minimum switching frequency is reached. The difference between VVBST and VSW
must be maintained at a value higher than 2.4 V.
FORCED CONTINUOUS CONDUCTION MODE
When the PS pin is grounded or greater than 2.2 V, the TPS53311 is operating in forced continuous conduction
mode in both light-load and heavy-load conditions. In this mode, the switching frequency remains constant over
the entire load range, making it suitable for applications that need tight control of switching frequency at a cost of
lower efficiency at light load.
SOFT START
The soft-start function reduces the inrush current during the start up sequence. A slow-rising reference voltage is
generated by the soft-start circuitry and sent to the input of the error amplifier. When the soft-start ramp voltage
is less than 600 mV, the error amplifier uses this ramp voltage as the reference. When the ramp voltage reaches
600 mV, the error amplifier switches to a fixed 600-mV reference. The typical soft-start time is 400 µs.
POWER GOOD
The TPS53311 monitors the voltage on the FB pin. If the FB voltage is between 83% and 117% of the reference
voltage, the power good signal remains high. If the FB voltage falls outside of these limits, the internal open drain
output pulls the power good pin (PGD) low.
During start-up, the power good signal is delayed for 400 µs after the FB voltage falls to within the power good
limits. There is also 10-µs delay during the shut down sequence.
UNDERVOLTAGE LOCKOUT (UVLO) FUNCTION
The TPS53311 provides undervoltage lockout (UVLO) protection for both power input (VIN) and bias input (VDD)
voltage. If either of them is lower than the UVLO threshold voltage minus the hysteresis, the device shuts off.
When the voltage rises above the threshold voltage, the device restarts. The typical UVLO rising threshold is 2.8
V for both VIN and VVDD. A hysteresis voltage of 130 mV for VIN and 75 mV for VVDD is also provided to prevent
glitch.
OVERCURRENT PROTECTION
The TPS53311 continuously monitors the current flowing through the high-side and the low-side MOSFETs. If
the current through the high-side FET exceeds 4.5 A, the high-side FET turns off and the low-side FET turns on.
An overcurrent (OC) counter starts to increment each occurrence of an overcurrent event. The converter shuts
down immediately when the OC counter reaches four. The OC counter resets if the detected current is less 4.5 A
after an OC event.
12
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
TPS53311
www.ti.com
SLUSA41 – JUNE 2010
Another set of overcurrent circuitry monitors the current flowing through low-side FET. If the current through the
low-side FET exceeds 5.1 A, the overcurrent protection is enabled and immediately turns off both the high-side
and the low-side FETs . The device is fully protected against overcurrent during both on-time and off-time. This
protection is latched. Please refer to the TPS53310 data sheet (SLUSA68) for information on hiccup overcurrent
protection.
OVERVOLTAGE PROTECTION
The TPS53311 monitors the voltage divided feedback voltage to detect overvoltage and undervoltage conditions.
When the feedback voltage is greater than 117% of the reference, the high-side MOSFET turns off and the
low-side MOSFET turns on. The output voltage then drops until it reaches the undervoltage threshold. At that
point the low-side MOSFET turns off and the device enters a high-impedance state.
UNDERVOLTAGE PROTECTION
When the feedback voltage is lower than 83% of the reference voltage, the undervoltage protection timer starts.
If the feedback voltage remains lower than the undervoltage threshold voltage after 10 ms, the device turns off
both the high-side and the low-side MOSFETs and goes into a high-impedance state. This protection is latched.
OVERTEMPERATURE PROTECTION
The TPS53311 continuously monitors the die temperature. If the die temperature exceeds the threshold value
(140˚C typical), the device shuts off. When the device temperature falls to 40˚C below the overtemperature
threshold, it restarts and returns to normal operation.
OUTPUT DISCHARGE
When the enable pin is low, the TPS53311 discharges the output capacitors through an internal MOSFET switch
between SW and PGND while high-side and low-side MOSFETs remain off. The typical discharge switch-on
resistance is 60 Ω. This function is disabled when VIN is less than 1 V.
MASTER/SLAVE OPERATION AND SYNCHRONIZATION
Two TPS53311 can operate interleaved when configured as master/slave. The SYNC pins of the two devices are
connected together for synchronization. In CCM, the master device sends the 180° out-of-phase pulse to the
slave device through the SYNC pin, which determines the leading edge of the PWM pulse. If the slave device
does not receive the SYNC pulse from the master device or if the SYNC connection is broken during operation,
the slave device continues to operate using its own internal clock.
The SYNC pin of the slave device can also connect to external clock source within ±20% of the 1.1-MHz
switching frequency. The falling edge of the SYNC triggers the rising edge of the PWM signal.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
13
TPS53311
SLUSA41 – JUNE 2010
www.ti.com
EXTERNAL COMPONENTS SELECTION
1. DETERMINE THE VALUE OF R1 AND R2
The output voltage is programmed by the voltage-divider resistor, R1 and R2 shown in Figure 13. R1 is
connected between the FB pin and the output, and R2 is connected between the FB pin and GND. The
recommended value for R1 is from 1 kΩ to 5 kΩ. Determine R2 using equation in Equation 1.
0.6
R2 =
´ R1
VOUT - 0.6
(1)
2. CHOOSE THE INDUCTOR
The inductance value should be determined to give the ripple current of approximately 20% to 40% of maximum
output current. The inductor ripple current is determined by Equation 2:
IL(ripple ) =
(VIN - VOUT )´ VOUT
1
´
L ´ fSW
VIN
(2)
The inductor also needs to have low DCR to achieve good efficiency, as well as enough room above peak
inductor current before saturation.
3. CHOOSE THE OUTPUT CAPACITOR(S)
The output capacitor selection is determined by output ripple and transient requirement. When operating in CCM,
the output ripple has three components:
VRIPPLE = VRIPPLE(C ) + VRIPPLE(ESR ) + VRIPPLE(ESL )
(3)
VRIPPLE(C ) =
IL(ripple )
8 ´ COUT ´ fSW
(4)
VRIPPLE(ESR ) = IL(ripple ) ´ ESR
(5)
V ´ ESL
VRIPPLE(ESL ) = IN
L
(6)
When ceramic output capacitors are used, the ESL component is usually negligible. In the case when multiple
output capacitors are used, ESR and ESL should be the equivalent of ESR and ESL of all the output capacitor in
parallel.
When operating in DCM, the output ripple is dominated by the component determined by capacitance. It also
varies with load current and can be expressed as shown in Equation 7.
VRIPPLE(DCM) =
(a ´ I (
L ripple ) - IOUT
2
)
2 ´ COUT ´ fSW ´ IL(ripple )
where
•
a=
14
a is the DCM on-time coefficient and can be expressed in Equation 8 (typical value 1.25)
(7)
tON(DCM)
tON(CCM)
(8)
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
TPS53311
www.ti.com
SLUSA41 – JUNE 2010
IL
VOUT
a x IL(ripple)
VRIPPLE
IOUT
T1
axT
UDG-10055
Figure 14. DCM VOUT Ripple Calculation
4. CHOOSE THE INPUT CAPACITOR
The selection of input capacitor should be determined by the ripple current requirement. The ripple current
generated by the converter needs to be absorbed by the input capacitors as well as the input source. The RMS
ripple current from the converter can be expressed in Equation 9.
IIN(ripple ) = IOUT ´ D ´ (1 - D )
where
•
D is the duty cycle and can be expressed as shown in Equation 10
(9)
V
D = OUT
VIN
(10)
To minimize the ripple current drawn from the input source, sufficient input decoupling capacitors should be
placed close to the device. The ceramic capacitor is recommended because it provides low ESR and low ESL.
The input voltage ripple can be calculated as shown in Equation 11 when the total input capacitance is
determined.
´D
I
VIN(ripple ) = OUT
fSW ´ CIN
(11)
5. COMPENSATION DESIGN
The TPS53311 uses voltage mode control. To effectively compensate the power stage and ensure fast transient
response, Type III compensation is typically used.
The control to output transfer function can be described in Equation 12.
1 + s ´ COUT ´ ESR
GCO = 4 ´
æ
ö
L
+ COUT ´ (ESR + DCR) ÷ + s2 ´ L ´ COUT
1+ s ´ ç
+
DCR
R
LOAD
è
ø
(12)
The output L-C filter introduces a double pole which can be calculated as shown in Equation 13.
1
fDP =
2 ´ p ´ L ´ COUT
(13)
The ESR zero can be calculated as shown in Equation 14.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
15
TPS53311
SLUSA41 – JUNE 2010
fESR =
www.ti.com
1
2 ´ p ´ ESR ´ COUT
(14)
Figure 15 and Figure 16 show the configuration of Type III compensation and typical pole and zero locations.
Equation 16 through Equation 20 describe the compensator transfer function and poles and zeros of the Type III
network.
C3
C1
C2
R4
R3
COMP
+
VREF
R2
Gain (dB)
R1
UGD-10058
fZ1
fZ2
fP2
fP3
Frequency
UDG-10057
Figure 15. Type III Compensation Network
Configuration Schematic
GEA =
(1 + s ´ C1 ´ (R1 + R3 ))(1 + s ´ R4 ´ C2 )
æ
C ´C ö
(s ´ R1 ´ (C2 + C3 ))´ (1 + s ´ C1 ´ R3 )´ ç 1 + s ´ R4 C 2 + C3 ÷
è
fZ1 =
Figure 16. Type III Compensation Gain Plot and
Zero/Pole Placement
2
3
ø
1
2 ´ p ´ R 4 ´ C2
(15)
(16)
1
1
fZ2 =
@
2 ´ p ´ (R1 + R3 ) ´ C1 2 ´ p ´ R1 ´ C1
(17)
fP1 = 0
(18)
1
fP2 =
2 ´ p ´ R3 ´ C1
(19)
1
1
fP3 =
@
æ C ´ C3 ö 2 ´ p ´ R 4 ´ C3
2 ´ p ´ R4 ´ ç 2
÷
è C2 + C3 ø
(20)
The two zeros can be placed near the double pole frequency to cancel the response from the double pole. One
pole can be used to cancel ESR zero, and the other non-zero pole can be placed at half switching frequency to
attenuate the high frequency noise and switching ripple. Suitable values can be selected to achieve a
compromise between high phase margin and fast response. A phase margin higher than 45 degrees is required
for stable operation.
For DCM operation, a C3 between 56 pF and 150 pF is recommended for output capacitance between 20 µF to
200 µF.
16
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
TPS53311
www.ti.com
SLUSA41 – JUNE 2010
Figure 17 shows the master/slave configuration schematic for a design with a 3.3-V input.
L1
1 mH
Output all MLCCs
VIN
3.3 V
C5
22 mF
C6
0.1 mF
R6
2.2 W
C8
1 mF
13
14
VIN
VIN
5
6
COUT
3 x 22 mF
7
C4
VIN
0.1 mF
SW SW SW
12 VDD
VBST
4
PGD
3
R7
20 kW
PGD_Master R3
20 W
11 AGND
TPS53311
EN_Master
2
SYNC
1
EN
8
PS
FB 10
PGND PGND COMP
15
R1
9
4.02 kW
R2
4.02 kW
C3
100 pF
16
L1
1 mH
Output all MLCCs
C6
0.1 mF
R6
2.2 W
C8
1 mF
13
14
VIN
VIN
5
6
7
C4
VIN
0.1 mF
VBST
4
PGD
3
R7
20 kW
PGD_Master R3
20 W
11 AGND
TPS53311
2
SYNC
1
EN
8
PS
FB 10
PGND PGND COMP
15
VOUT = 1.5 V
COUT
3 x 22 mF
SW SW SW
12 VDD
EN_Slave
C1
2.2 nF
R4
C2 2.2 nF 4.02 kW
VIN
C5
22 mF
VOUT = 1.2 V
R4
C2 2.2 nF 4.02 kW
9
16
C1
2.2 nF
R1
4.02 kW
R2
4.02 kW
C3
100 pF
UDG-10059
Figure 17. Master/Slave Configuration Schematic
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
17
TPS53311
SLUSA41 – JUNE 2010
www.ti.com
LAYOUT CONSIDERATIONS
Good layout is essential for stable power supply operation. Follow these guidelines for a clean PCB layout:
• Separate the power ground and analog ground planes. Connect them together at one location.
• Use four vias to connect the thermal pad to power ground.
• Place VIN and VDD decoupling capacitors as close to the device as possible.
• Use wide traces for VIN, VOUT, PGND and SW. These nodes carry high current and also serve as heat sinks.
• Place feedback and compensation components as close to the device as possible.
• Keep analog signals (FB, COMP) away from noisy signals (SW, SYNC, VBST).
• Refer to TPS53311 evaluation module for a layout example.
18
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS53311
PACKAGE OPTION ADDENDUM
www.ti.com
24-Jun-2010
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
TPS53311RGTR
ACTIVE
QFN
RGT
16
3000
Green (RoHS
& no Sb/Br)
TPS53311RGTT
ACTIVE
QFN
RGT
16
250
Green (RoHS
& no Sb/Br)
Lead/
Ball Finish
MSL Peak Temp
(3)
(Requires Login)
CU NIPDAU Level-2-260C-1 YEAR
Call TI
Samples
Level-2-260C-1 YEAR
Purchase Samples
Request Free Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated