INTEL N82503

82503
DUAL SERIAL TRANSCEIVER (DST)
82503 PRODUCT FEATURE SET OVERVIEW
Y
Single Component Ethernet* Interface
to Both 802.3 10BASE-T and AUI
Y
Automatic or Manual Port Selection
Y
Y
Manchester Encoder/Decoder and
Clock Recovery
No Glue Interface to Industry-Standard
LAN Controllers
Ð Intel 82586, 82590, 82593 and 82596
Ð AMD 7990 (LANCE*)
Ð National Semiconductor 8390 and
83932 (SONIC*)
Ð Western Digital 83C690
Ð Fujitsu 86950 (Etherstar*)
Y
Diagnostic Loopback
Y
Reset, Low Power Modes
Y
Network Status Indicators
Y
Defeatable Jabber Timer
Y
User Test Modes
Y
10 MHz Transmit Clock Generator
Y
One Micron CHMOS** IV (Px48)
Technology
Y
Single 5-V Supply
INTERFACE FEATURES
TPE
Y
Y
Complies with 10BASE-T, IEEE Std.
802.3i-1990 for Twisted Pair Ethernet
Selectable Polarity Switching
Y
Direct Interface to TPE Analog Filters
Y
On-Chip TPE Squelch
Y
Defeatable Link Integrity (LI)
Y
Support of Cable Lengths l 100m
AUI
Y
Complies with IEEE 802.3 AUI Standard
Y
Direct Interface to AUI Transformers
Y
On-Chip AUI Squelch
A block diagram of a typical application is shown in Figure 1. The 82503 Dual Serial Transceiver is a high-integration CMOS device designed to simplify interfacing industry standard Ethernet LAN Controllers to IEEE
802.3 local area network applications (10BASE5, 10BASE2, and 10BASE-T). The component supports both
an attachment unit interface (AUI) and a Twisted Pair Ethernet interface (TPE). It allows OEMs to design a
state-of-the-art media interface that is jumperless and fully automatic. The 82503 includes on-chip AUI and
TPE drivers and receivers; it offers designers a cost-effective, integrated solution for interfacing LAN controllers to the wire medium.
**CHMOS is a patented process of Intel Corporation.
*Ethernet is a registered trademark of Xerox Corporation.
LANCE is a registered trademark of Advanced Micro Devices.
Etherstar is a registered trademark of Fujitsu Electronics.
Sonic is a registered trademark of National Semiconductor Corporation.
*Other brands and names are the property of their respective owners.
Information in this document is provided in connection with Intel products. Intel assumes no liability whatsoever, including infringement of any patent or
copyright, for sale and use of Intel products except as provided in Intel’s Terms and Conditions of Sale for such products. Intel retains the right to make
changes to these specifications at any time, without notice. Microcomputer Products may have minor variations to this specification known as errata.
COPYRIGHT © INTEL CORPORATION, 1996
October 1995
Order Number: 290421-004
82503 Dual Serial Transceiver (DST)
CONTENTS
PAGE
1.0 82503 PRODUCT FEATURES ÀÀÀÀÀÀÀÀÀ 3
2.0 PIN DEFINITION ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 5
2.1 Power Pins ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 6
2.2 Clock Pins ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 6
2.3 AUI Pins ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 6
2.4 TPE Pins ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 7
2.5 Controller Interface Pins ÀÀÀÀÀÀÀÀÀÀÀÀÀ 7
2.6 Mode Pins ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 8
2.7 LED Pins ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 9
3.0 82503 ARCHITECTURE ÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 10
3.1 Clock Generation ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 10
3.2 Transmit Blocks ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 10
3.3 Receive Blocks ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 11
3.4 Collision Detection ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 13
3.5 Link Integrity ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 13
3.6 Jabber Function ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 13
3.7 TPE Loopback ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 13
3.8 SQE Test Function ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 14
3.9 Port Selection ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 14
3.10 LED Description ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 14
3.11 Polarity Switching ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 14
3.12 Controller Interface ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 15
2
CONTENTS
PAGE
4.0 RESET, LOW POWER AND TEST
MODES ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 16
4.1 Reset ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 16
4.2 Low Power and High Impedance
Modes ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 16
4.3 Diagnostic Loopback ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 16
4.4 Customer Test Modes (Continuous
AUI/TPE Transmit) ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 16
5.0 APPLICATION EXAMPLE ÀÀÀÀÀÀÀÀÀÀÀÀ 17
5.1 Introduction ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 17
5.2 Design Guidelines ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 17
5.3 Layout Guidelines ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 17
6.0 PACKAGE THERMAL
SPECIFICATIONS ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 19
7.0 ELECTRICAL SPECIFICATIONS
AND TIMINGS ÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀÀ 20
82503
290421 – 1
Figure 1. Application Block Diagram
1.0
82503 PRODUCT FEATURES
The 82503 incorporates all the active circuitry required to interface Ethernet controllers to 10BASE-T
networks or the attachment unit interface (AUI). It
supports a direct no-glue interface to Intel’s family of
high-performance LAN controllers (82586, 82590,
82593, and 82596). The 82503 also provides a direct no-glue interface to the National Semiconductor
8390 and 83932 (SONIC), the Western Digital
83C690, the Advanced Micro Devices 7990
(LANCE) and 79C900 (ILACC), and the Fujitsu
86950 (Etherstar) controllers.
This component includes three advanced features:
jumperless two-port design capability, automatic port
selection, and polarity switching. The jumperless
TPE or AUI port selection capability allows designers maximum ease-of-use and network flexibility. Automatic port selection ensures complete software
compatibility with existing 10BASE2 and 10BASE5
software drivers. The 82503’s polarity switching feature will detect and correct polarity errors on the
twisted pairÐthe most common wiring fault in twisted pair networks.
The 82503 contains all the circuitry needed to meet
the 10BASE-T specification, including link integrity, a
jabber timer and internal predistortion. Deselecting
link integrity allows the component to be used in
some prestandard networks. The 82503’s jabber
timer prevents the station from continuously transmitting and is defeatable for simple design charac-
terization. The predistortion circuitry eliminates line
overcharge and reduces jitter on 10BASE-T links.
The 82503 can also support twisted pair cable
lengths of up to 200m when placed in TPE Extended
Squelch Mode (XSQ).
This component incorporates six LED drivers to display transmit data, receive data, collision, link integrity, polarity faults and port selections, allowing for
complete network monitoring by the user. The transmit, receive and collision LEDs indicate the rate of
activity by the frequency of flashing. The 82503 also
has a low power mode. During low power, many of
the 82503’s pins are in a high-impedance state to
facilitate board-level testing.
The 82503’s diagnostic loopback control enables it
to route a transmission signal from the LAN controller through its Manchester encoder-decoder circuitry
and back to the LAN controller. This provides effective network node fault detection and isolation capabilities. In addition, the 82503 supports diagnostic
test modes that generate continuous tranmission of
data through the twisted pair port, allowing designers to measure the analog performance of their design.
The 82503 is available in 44-lead PLCC and 44-lead
QFP packages and is fabricated with Intel’s lowpower, high-speed, CHMOS IV technology using a
single 5-V supply.
3
82503
290421 – 2
Figure 2. 82503 Functional Block Diagram
4
82503
2.0
PIN DEFINITION
290421 – 3
Figure 3. 44-Lead PLCC Pin Configuration
290421 – 44
Figure 4. 44-Lead QFP Pin Configuration
5
82503
2.1 Power Pins
PLCC
Pin
QFP
Pin
Type
VSS(1)
7, 17, 39
1, 11, 33
Supply
(1)
Symbol
VCC
Name and Function
Digital Ground.
6, 18, 40
44, 12, 34
Supply
Digital VCC. A 5-V g 5% Power Supply.
VCCA(1)
28
22
Supply
Analog VCC. A 5-V g 5% Power Supply.
VSSA(1)
29
23
Supply
Analog Ground.
NOTE:
1. VCC and VCCA must be connected to the same power supply. VSS and VSSA must be connected to the same ground.
Separate decoupling and noise conditioning (e.g., ferrite beads) should be used.
2.2 Clock Pins
Symbol
PLCC
Pin
QFP
Pin
Type
X1
21
15
I
CLOCK CRYSTAL. A 20 MHz crystal input. This pin can be driven
with an external MOS level clock when X2 is left floating.
X2
20
14
O
CLOCK CRYSTAL. A 20 MHz crystal output. X1 can be driven with
an external MOS level clock when this pin is left floating.
PLCC
Pin
QFP
Pin
Type
Name and Function
TRMT
TRMT
27
26
21
20
O
O
TRANSMIT PAIR. A differential output driver pair that drives the
transmit pair of the transceiver cable. The output bit stream is
Manchester encoded. Following the last transition, which is positive
at TRMT, the differential voltage is reduced to zero volts.
RCV
RCV
31
30
25
24
I
I
RECEIVE PAIR. A differentially driven input pair which is tied to the
receive pair of the Ethernet transceiver cable. The first transition on
RCV is negative-going to indicate the beginning of the frame. The
last transition is positive-going to indicate the end of the frame. The
received bit stream is assumed to be Manchester encoded.
CLSN
CLSN
25
24
19
18
I
I
COLLISION PAIR. A differentially driven input pair tied to the
collision presence pair of the Ethernet transceiver cable. The
collision presence signal is a 10 MHz square wave. The first
transition at CLSN is negative-going to indicate the beginning of the
signal; the last transition is positive-going to indicate the end of the
signal.
Name and Function
2.3 AUI Pins
Symbol
6
82503
2.4 TPE Pins
PLCC
Pin
QFP
Pin
Type
Name and Function
TDH
TDH
TDL
TDL
35
37
34
36
29
31
28
30
O
O
O
O
TP TRANSMIT PAIR DRIVERS. These four outputs constitute the
twisted-pair drivers, which have predistortion capabilities. The TDH/
TDH outputs generate the 10 Mb/s Manchester Encoded data. The
TDL/TDL outputs mirror the TDH/TDH outputs except for fat bit
occurrences (100 ns pulses). During the second half of a fat bit
(either high or low), the TDL/TDL outputs are inverted with respect
to TDH/TDH outputs. This signal behavior reduces the amount of
jitter by preventing overcharge on the twisted pair medium.
RD
RD
32
33
26
27
I
I
TP RECEIVE PAIR. The differential twisted pair receiver. The
receiver pair is connected to the twisted pair medium and is driven
with 10 Mb/s Manchester encoded data.
Symbol
2.5 Controller Interface Pins
PLCC
Pin
QFP
Pin
Type
TxC
9
3
O
TRANSMIT CLOCK. A 10 MHz clock output tied directly to the
transmit clock pin of the Ethernet controller. Changes sense
depending on controller selected. Active low for Intel and Fujitsu
controller interfaces, active high for National and AMD interfaces.
Can drive one TTL load.
TxD
16
10
I
TRANSMIT DATA. TTL input. NRZ serial data is clocked in on TxD
from the Ethernet controller. Connects directly to the transmit data
pin of the Ethernet controller.
RTS
15
9
I
REQUEST TO SEND. TTL input. An active low input signal
synchronous to TxC which enables data transmission on the active
port. Changes sense depending on controller selected. Active low
for the Intel controller interface, active high for National, AMD, and
Fujitsu interfaces.
RxC
14
8
O
RECEIVE CLOCK. A 10 MHz clock output tied directly to the
receive clock pin of the Ethernet controller. This clock is the
recovered clock from incoming data on the active port. Changes
sense depending on controller selected. Active low for Intel and
Fujitsu controller interfaces, active high for National and AMD
interfaces. Can drive one TTL load.
RxD
13
7
O
RECEIVE DATA. Received NRZ data (synchronous to RxC) passed
to the Ethernet controller. Connect directly to the receive data pin of
the controller. Can drive one TTL load.
CRS
10
4
O
CARRIER SENSE. Output that alerts the Ethernet controller that
data is present on the active port. Connects directly to the carrier
sense pin of the Ethernet controller. Changes sense depending on
controller mode selected. Active low for Intel controller interface,
active high for National, AMD, and Fujitsu interfaces. Can drive one
TTL load.
CDT
12
6
O
COLLISION DETECT. Output that indicates presence of a collision.
Connects directly to the collision detect pin of the Ethernet
controller. Changes sense depending on controller selected. Active
low for Intel and Fujitsu controller interfaces, active high for National
and AMD interfaces. Can drive one TTL load.
Symbol
Name and Function
7
82503
2.6 Mode Pins
PLCC
Pin
QFP
Pin
Type
Name and Function
TPE/AUI
2
40
I/O
PORT SELECT. TTL input/LED output. If APORT is low,
TPE/AUI is an input and selects either the TPE port (TPE/AUI
high) or AUI port (TPE/AUI low). If APORT is high, the 82503 will
indicate the port selected by driving TPE/AUI high (TPE) or low
(AUI). TPE/AUI can drive an LED pull-up.
APORT
3
41
I
AUTOMATIC PORT SELECTION. TTL input. When high, 82503
will automatically select TPE or AUI port based on presence of
valid link beats or frames on the TPE receive input. Mode
selected will be indicated on TPE/AUI.
APOL/XSQ
4
42
I
AUTOMATIC POLARITY CORRECTION/EXTENDED
SQUELCH ENABLE. TTL input. When high, the extended
squelch mode is disabled and automatic polarity correction is
enabled. Both junctions (APOL and XSQ) are enabled when this
pin is at a high impedance state. When low, both functions
become disabled. The presence of a polarity fault on the TPE
receive pair is indicated on POLED regardless of the state of
APOL.
LID
38
32
I
LINK INTEGRITY DISABLE. TTL input. If high, link integrity
function is disabled. If low, link integrity function is enabled.
CS0
CS1
5
8
43
2
I
I
CONTROLLER SELECT. Selects the appropriate interface for
the desired Ethernet controller. When CS0/1 e 0/0, supports
Intel controllers. When CS0/1 e 0/1, supports Fujitsu
controllers. When CS0/1 e 1/0, supports Western Digital and
National controllers. When CS0/1 e 1/1, supports AMD
controllers. (See Table 2.)
LPBK
11
5
I
LOOPBACK. TTL input. An active low input signal that causes
the 82503 to enter diagnostic loopback mode. The twisted pair
or AUI medium will be removed from the circuit, thus isolating
the node from the network. When not connected, this pin
assumes the inactive (high) state. Diagnostic loopback does not
disable the operation of the link integrity processor, link beat
generator, or automatic port selection.
JABD
23
17
I
JABBER DISABLE. TTL input. When high, this pin disables the
jabber function. When low, the jabber function is enabled and
the device performs AUI or TP jabber protection for the active
port. If this pin and TEST are asserted during a falling edge of
RESET, the 82503 enters its low power mode; when either this
pin or TEST deasserts, then the 82503 transitions to its normal
operating mode.
TEST
19
13
I
TEST MODE ENABLE. TTL input. When TEST is high and
RESET is deasserted, a customer test mode is directly
accessed. When driven low, test mode is disabled. If this pin and
JABD are asserted during a falling edge of RESET, the 82503
enters its low power mode; when either this pin or JABD
deasserts, then the 82503 transitions to its normal operating
mode.
RESET
22
16
I
RESET. TTL input. When high, resets internal circuitry. On the
falling edge of RESET, either test mode or low power mode can
be entered depending on the state of JABD and TEST.
Symbol
8
82503
2.7 LED Pins
Symbol
PLCC
Pin
QFP
Pin
Type
Name and Function
TxLED
42
36
I/O
TRANSMIT LED. LED output. Indicates transmit status of the AUI or
TPE port. Normally off (high) output. Turns on to indicate
transmission. Flashes at a rate dependent on the level of transmit
activity. Upon entering a customer test mode, this pin must be
driven high either through an LED, or a resistor.
RxLED
43
37
I/O
RECEIVE LED. LED output. Indicates receive status of the AUI or
TPE port. Normally off (high) output. Turns on to indicate reception.
Flashes at a rate dependent on the level of receive activity. Upon
entering a customer test mode, this pin must be driven high either
through an LED, or a resistor.
COLED
44
38
I/O
COLLISION LED. LED output. Indicates collision status of the AUI
or TPE port. Normally off (high) output. Turns on to indicate
collision. Flashes at a rate dependent on the level of collision
activity. This pin is also used to determine which customer test
modes are entered.
LILED
41
35
O
LINK INTEGRITY LED. LED output. Normally on (low) output which
indicates good link integrity on the TPE port during TPE mode.
Remains on when link integrity function has been disabled. Turns off
during AUI mode or when link integrity fails in TPE mode. Minimum
off time is 100 ms, minimum on time is set by the link integrity
function.
POLED
1
39
O
POLARITY INDICATION. LED output. If the 82503 detects that the
receive TPE wires are reversed, POLED will turn on (low) to indicate
the fault. POLED remains on even if APOL/XSQ is high and the
82503 has automatically corrected for the reversed wires.
NOTE:
1. The LED outputs have a weak pull-up capable of sourcing 500 mA. They can sink 10 mA while still meeting TTL levels. All
LEDs can be used as indication pins if no LED is needed. Some of these outputs include pulse width conditioning, which
should be accounted for in software.
9
82503
3.0
82503 ARCHITECTURE
3.2 Transmit Blocks
3.1 Clock Generation
3.2.1 MANCHESTER ENCODER
A 20 MHz parallel resonant crystal is used to control
the clock generation oscillator, which provides the
basic 20 MHz clock source. An internal divide-bytwo counter generates the 10 MHz g 0.01% clock
required by the IEEE 802.3 specification.
The 20 MHz clock is used to Manchester-encode
data on the TxD input. This clock is also divided by
two to produce the 10 MHz clock the LAN controller
needs for synchronizing its RTS and TxD signals.
We recommend a crystal that meets the following
specifications be used.
# Quartz Crystal
# 20 MHz g 0.002% at 25§ C
# Accuracy g 0.005% over full operating temperature, 0§ C to a 70§ C
# Parallel resonant with 20 pF Load Fundamental
Mode
# Maximum Series Resistance: RSERIES e 30X
Several vendors have such crystals; either-off-the
shelf or custom made. Two possible vendors are:
1. M-Tron Industries, Inc.
Yankton, SD 57078
Specifications;
Part No. HC49 with 20 MHz, 50 PPM over 0§ C to
a 70§ C, and 20 pF fundamental load.
2. Crystek Corporation
100 Crystal Drive
Ft. Myers, FL 33907
Part No. 013212
The accuracy of the Crystal Oscillator frequency depends on the PC board characteristics, therefore it is
advisable to keep the X1 and X2 traces as short as
possible. The optimum value of C1 and C2 should
be determined experimentally under nominal operating conditions. The typical value of C1 and C2 is
between 22 pF and 35 pF.
An external 20 MHz MOS-level clock may be applied
to pin X1, if pin X2 is left floating.
10
Data encoding and transmission begins with RTS
asserting. Since the first bit of a transmission is a 1,
the first transition is always negative on the transmit
outputs (TRMT or TD pins). Transmission ends
when RTS deasserts. The last transition is always
positive at the transmit outputs (TRMT or TD pins)
and may occur at the center of the bit cell if the last
data bit to be transmitted is a 1, or at the boundary
of the bit cell if the last data bit to be sent is a 0.
Immediately after the end of a transmission, all signals on the RCV pair (when AUI mode is selected)
are inhibited for 4 to 5 ms. This dead time is necessary for proper operation of the SQE (heartbeat)
test.
3.2.2 AUI CABLE DRIVER
The AUI cable driver (TRMT pair) is a differential
circuit, which interfaces to the AUI cable through a
pulse transformer.
High voltage protection is achieved by using a transformer to isolate the transmit pins (TRMT pair) from
the transceiver cable. The total transmit circuit inductance, including the 802.3 transceiver transformers, should be a minimum of 27 mH for Ethernet applications.
3.2.3 TWISTED PAIR CABLE DRIVER
The twisted pair line drivers (TD pairs) begin transmitting the serial Manchester bit stream 3 bit times
after RTS is asserted. The line drivers use a predistortion algorithm to improve jitter performance for up
to 100 meters of twisted pair cable. The line drivers
reduce their drive level during the second half of
‘‘fat’’ (100 ns) Manchester pulses and maintain a full
drive level during all ‘‘thin’’ (50 ns) pulses and during
the first half of the ‘‘fat’’ pulses. This reduces line
overcharging during ‘‘fat’’ pulses, a major source of
jitter.
82503
290421 – 4
Figure 5. TPE Predistortion
3.3 Receive Blocks
3.3.1 MANCHESTER DECODER AND CLOCK
RECOVERY
The 82503 performs Manchester decoding and timing recovery of the incoming data in AUI and TPE
modes.
The Manchester-encoded data stream is decoded to
separate the Receive Clock (RxC) and the Receive
Data (RxD) from the differential signal. The 82503
uses an advanced digital technique to perform the
decoding function. The use of digital circuitry instead
of analog circuitry (e.g., a phase-lock loop) to perform the decoding ensures that the decoding function is less sensitive to variations in operating conditions.
A high-resolution phase reference is used to digitize
the phase of the incoming data bit-center transition.
The digitizer has a phase resolution of 1/32 of a bit
time.
The digitized phase is filtered by a digital low-pass
filter to remove rapid phase variations, i.e., phase
jitter. Slow phase variations, such as those caused
by small differences between the data frequency
and the clock frequency, are not filtered by the lowpass filter.
The RxC generator digitally sets the phases of the
two RxC transitions to respectively lead and lag the
bit-center transition by (/4 bit time. RxC is used to
recover RxD by sampling the incoming data with an
edge-triggered flip-flop.
Lock is achieved by reducing the time constant of
the digital filter to zero at the start of a new frame.
Any uncertainty in the bit-center phase of the first
transition that is caused by jitter is subsequently removed by gradually increasing the filter time constant during the following preamble. By that time, the
phase of the bit center is output by the filter, and
lock is achieved. Lock is achieved within the first 14
bit times as seen by the AUI inputs. The maximum
bit-cell timing distortion (jitter) tolerated by the Manchester decoder circuitry is g 12 ns (preamble),
g 18 ns (data) for AUI, and g 13.5 ns for TPE (data
and preamble).
11
82503
290421 – 5
Figure 6. Manchester Decoder and Clock Recovery
3.3.2 AUI RECEIVE AND COLLISION BUFFERS
The AUI receive and collision inputs are driven
through isolation transformers to provide high voltage protection and DC common mode voltage rejection. The incoming signals are converted to digital
levels and passed to the Manchester decoder and
collision detection circuitry.
3.3.3 AUI RECEIVE AND COLLISION
SQUELCH CIRCUITS
Both the receive (RCV) and collision (CLSN) pairs
have the following squelch characteristics.
# The squelch circuits are turned on at idle.
# A pulse is rejected if the peak differential voltage
is more positive than b 160 mV regardless of
pulse width.
# A pulse is considered valid if its peak differential
voltage is more negative than b 300 mV and its
width, measured at b 285 mV, is greater than
25 ns.
# The squelch circuits are disabled by the first valid
negative differential pulse on either the AUI receive (RCV) or the AUI collision (CLSN) pair.
# If a positive differential pulse occurs on either the
AUI receive or collision pairs for greater than
160 ns, End of Frame (EOF) is assumed and the
squelch circuitry is turned on.
3.3.4 TPE RECEIVE BUFFER
The TPE receive pins (RD and RD) are connected to
the twisted pair medium through an analog front
end. The analog front end contains the line coupling
12
devices and EMI filters necessary to conform to the
10BASE-T standards and local RF regulations. The
input differential voltage range for the TPE receiver
is greater than 500 mV and less than 3.1V differential.
3.3.5 TPE RECEIVE SQUELCH CIRCUITS
The TPE receive buffer distinguishes valid receive
differential data, link test pulses, and the idle condition according to the requirements of the 10BASE-T
standard. Signals at the output of the EMI filter (thus
at the RD and RD pair) are rejected as follows:
# All differential pulses of peak magnitude less than
300 mV are rejected.
# All continuous sinusoids with a differential amplitude less than 6.2 VPP and a frequency less than
2 MHz are rejected.
# All sine waves of single cycle duration starting
with phase 0§ or 180§ that have an amplitude less
than 6.2 VPP, and a frequency of 2 MHz to
16 MHz are rejected, if the single cycle is preceeded and followed by 4 bit times of silence
(i.e., a signal less than 300 mV).
3.3.6 TPE Extended Squelch Mode
By placing the 82503 into TPE extended squelch
mode, the 82503 can support cable lengths greater
than the 100m specified in the 10Base-T IEEE standard (802.3i-1990). The squelch thresholds for the
signals at the RD/RD pair are typically reduced by
4.5 dB. This allows Grade 5 twisted-pair cable to be
used to overcome attenuation and multipair crosstalk for cable lengths up to 200 meters.
82503
TPE extended squelch mode is enabled by presenting a high-impedance ( l 100 KX) at the APOL/XSQ
pin. This can be done by floating the APOL/XSQ pin,
tying APOL/XSQ low through a 100 KX resistor, or
driving APOL/XSQ with a three-state buffer. When
driven high or low using a TTL driver or a low impedance pull-up or pull-down ( k 2 KX) extended
squelch is disabled and the driven level at the
APOL/XSQ pin determines the state of the polaritycorrection function (APOL/XSQ e 1 enables polarity correction, APOL/XSQ e 0 disables polarity correction). The TPE extended squelch feature is transparent to previous steppings of the 82503. Polarity
correction is always enabled when the TPE extended-squelch feature is enabled (APOL/XSQ e Z).
The APOL/XSQ pin senses a high-impedance state
by an active-polling circuit implemented at the pin.
Two small polling devices attempt to pull the APOL/
XSQ pin up to VCC and down to VSS. If the pin is in a
high-impedance state, the devices will be successful
in pulling the APOL/XSQ pin high and low. If the pin
is driven high or low, the polling devices will not be
able to successfully pull the pin in the opposite direction. In this way, an internal state machine can
correctly determine one of three states of the
APOL/XSQ pin. The pin is polled every 25.6 ms.
to the twisted pair medium as an indication to the
remote MAU that the link is good. These pulses will
be transmitted 8 ms to 24 ms after the end of the
last transmission or link test pulse.
The link integrity function continuously monitors activity on the receive circuit. If neither valid data nor
link test pulses are received, the link integrity processor declares the link bad, and disables transmission and reception on the media, loopback, and the
SQE test function. Transmission of link test pulses
and monitoring receive activity are not affected. The
idle time required for the link integrity processor to
determine the link is bad is 50 ms to 150 ms.
Once a frame or a sequence of 2 to 10 valid consecutive link test pulses are detected, the Link Integrity
Processor declares the link is good, and reconnects
the transmitter and receiver.
The link integrity function can be disabled by driving
the LID pin high or by disabling automatic port selection (APORT e 0) and selecting the AUI port. This
option is intended primarily for use with pre10BASE-T networks.
3.6 Jabber Function
3.4 Collision Detection
3.4.1 AUI COLLISION DETECTION
Collision detection in the AUI mode is performed by
the attached transceiver, and signalled to the 82503
on the CLSN pair. A 10 MHz a 25%, or b 15%,
square wave with transition times between 35 ns
and 70 ns indicates the collision. The 82503 reports
this to the LAN controller on the CDT pin.
3.4.2 TPE COLLISION DETECTION
Collision detection in the TPE mode is indicated by
simultaneous transmission and reception on the
twisted pair link segment. The CDT signal is asserted for the duration of both RTS and the presence of
received data; CRS is asserted for the duration of
either RTS or the presence of received data. During
a collision, the source of RxD will be the received
data. If the received data stream ends before the
transmit data stream, the RxD source will be
changed to transmit data stream until it ends.
The 82503 contains a jabber timer to implement the
jabber function. If a transmission continues beyond
the limits specified, the jabber function inhibits further transmission and asserts the collision indicator,
CDT. The limits for jabber transmission are 20 ms to
150 ms in TPE Mode, and 8 ms to 16 ms in AUI
mode. For both AUI and TPE mode, the transmission inhibit period extends until the 82503 detects
sufficient idle time (between 250 ms and 750 ns) on
the RTS signal. The jabber function can be disabled
by driving the JABD high.
In TPE mode the link integrity function continues to
operate even if the jabber function is inhibiting transmission. Link test pulses continue to be sent and the
receive circuit continues to be monitored. Additionally, the link integrity function reconnects to a restored
link without waiting for the transmit input to go idle
when the jabber function is inhibiting transmission.
3.7 TPE Loopback
3.5 Link Integrity
In TPE mode the 82503 implements the transmit to
receive loopback (DO to DI) mode specified in the
10BASE-T standard. This mode loops back transmitted data through the receive path.
The 82503 supports the link integrity function as defined by 10BASE-T. During long periods of idle on
the transmitter, link test pulses will be transmitted on
This function is required to maintain full compatibility
with coax MAUs where the data loopback is a natural result of the architecture.
13
82503
The transmit to receive loopback function is disabled
when the jabber function or link integrity function is
inhibiting transmission.
3.8 SQE Test Function
The 82503 supports the SQE test function when in
TPE mode or in Diagnostic Loopback mode. The
82503 will assert its CDT pin within 0.6 ms to 1.6 ms
after the end of a transmission, and it will remain
asserted for 5- to 15-bit times. If the 82503 is in the
TPE mode and is not in diagnostic loopback mode,
the link integrity function will disable the SQE test
function when it detects a bad link.
3.10 LED Description
The 82503 supports six LED pins to indicate the
status of important states; TPE/AUI, TxLED,
POLED, LILED, RxLED, COLED. Each pin is capable
of directly driving an LED.
3.10.1 TPE/AUI
When automatic port selection is enabled (APORT is
high), TPE/AUI becomes an LED output and turns
off if TPE mode is selected and on if AUI mode is
selected.
3.10.2 TxLED
3.9 Port Selection
The 82503 features both manual and automatic port
selection. To enable automatic port selection, connect APORT to VCC. The 82503 then starts in TPE
mode and monitors link integrity. If the link is good,
the 82503 stays in TPE mode and pulls TPE/AUI
high to indicate that the TPE port was selected. If
link integrity fails, the 82503 switches to AUI mode
and pulls TPE/AUI low to indicate that the AUI port
is now active. TPE/AUI can drive an LED to indicate
port selection (on for AUI, off for TPE mode). Note
that LILED will be on if TPE mode is selected and off
if AUI mode is selected. If link integrity is disabled
while automatic port selection is enabled, the 82503
defaults to TPE mode. If the 82503 changes ports
while RTS is active, transmission is terminated with
an End of Frame marker on the old port. Transmission of the remaining packet fragment is not allowed
on the new port. Transmissions will begin with a
complete data packet.
The port can be manually selected by driving
APORT low. TPE/AUI e 0 selects AUI mode, and
TPE/AUI e 1 TPE mode. When the port is manually
selected, the circuitry for the unused port is powered
down. Changing ports requires 100 ms to allow the
circuitry for the new port to resume normal operation.
Table 1. Port Selection
Configuration
State
LID APORT TPE/AUI
X
X
0
1
0
0
1
1
0
1
X*
X*
AUI (TPE Port Powered Down)
TPE (AUI Port Powered Down)
Automatic Port Selection
TPE
NOTE:
*TPE/AUI is an output pin when APORT e 1.
Transmit status. This LED is normally off and flashes
at 2.5 Hz, 5 Hz, and 10 Hz to indicate respectively a
low, medium, and high rate of transmit activity.
3.10.3 RxLED
Receive LED. This LED is normally off and flashes at
2.5 Hz, 5 Hz, and 10 Hz to indicate respectively a
low, medium, and high rate of receive activity.
3.10.4 COLED
Collision LED. This LED is normally off and flashes
at 2.5 Hz, 5 Hz, and 10 Hz to indicate respectively a
low, medium, and high rate of collision activity.
3.10.5 POLED
Polarity Fault. This LED is normally off and turns on
to indicate a polarity fault in the receive pair of the
10BASE-T link. Operation of this pin is not affected
by the state of the polarity correction function
(APOL/XSQ e X).
3.10.6 LILED
Link Integrity status. When Aport is enabled
(APORT e 1), this LED is normally on (driven low)
to indicate the presence of a valid 10BASE-T link
when the TPE port is active. The LED will turn off
(driven high) when the link fails. When link integrity is
disabled (LID e 1) while APORT is enabled
(APORT e 1) this LED is turned on (driven low). If
APORT is disabled (APORT e 0) and the AUI port is
manually selected (TPE/AUI e 0) the LED output is
tristated.
3.11 Polarity Switching
In TPE mode, the 82503 monitors receive link beats
and end-of-frame delimiters for a possible receiver
14
82503
290421 – 6
Figure 7. Polarity Fault State Diagram
polarity error due to crossed wires. If Pin 4 of the
82503 is high and the TPE receive pins are reversed, the 82503 will correct the error by reversing
the signals internally, and turn POLED on (low) to
indicate that the fault has been detected and corrected. The polarity correction function is defeatable
by driving the APOL/XSQ input low. However, the
polarity fault will continue to be indicated on the
POLED.
3.12 Controller Interface
Connecting the 82503 to one of the Intel Ethernet
controllers (82586, 82590, 82593, 82596) requires
no additional components. Simply drive CS0 and
CS1 both low, and connect TxC, TxD, RTS, RxC,
RxD, CRS, CDT, and LPBK to the corresponding
controller pins.
The 82503 also works with other Ethernet controllers without additional components, including the
National Semiconductor 8390 and 83932 (SONIC),
Western Digital 83C690, Fujitsu 86950 (Etherstar),
depending on the state of and CS0 and CS1 inputs.
The interface of the 82503 to the AMD 7990
(LANCE) requires external logic to control the LPBK
pin of the 82503. Note that when an AMD LAN controller is used to interface to the 82503, the LPBK
pin of the 82503 becomes active high. That is, the
82503 enters diagnostic loopback mode when LPBK
pin is high and is in normal operation mode when
LPBK pin is low.
The logic sense of the 82503 controller pins will
change and should be connected to the controller
pins according to the following table.
15
82503
Table 2. Controller Interface Selection
82503
Pin
Intel
Controller
825XX
National, WD
Controllers
8390, 83C690,
83832 (SONIC)
AMD
Controller
7990 (LANCE),
79C900 (ILACC)
Fujitsu
Controllers
86950 (Etherstar)
CS0(1)
CS1
0
0
1
0
1
1
0
1
Pin
Pin
Sense
Pin
Sense
Pin
Sense
Pin
Sense
TxC
TxD
RTS
RxC
RxD
CRS
CDT
LPBK
TxC
TxD
RTS
RxC
RxD
CRS
CDT
LPBK
Low
High
Low
Low
High
Low
Low
Low
TXC
TXD
TXE
RXC
RXD
CRS
COL
LPBK
High
High
High
High
High
High
High
High
TCLK
TX
TENA
RCLK
RX
RENA
CLSN
High
High
High
High
High
High
High
TCKN
TXD
TEN
RCKN
RXD
XCD
XCOL
LPBK
Low
High
High
Low
High
High
Low
High
(Note 2)
NOTES:
1. CS0 and CS1 are intended to be static pins only. Switching CS0 and CS1 during network reception or transmission will
produce unpredictable results.
2. Refer to Section 3.12.
4.0
RESET, LOW-POWER AND
TEST MODES
4.1 Reset
When RESET is asserted the device resets its internal circuits. RESET is required after power up, and
before data can be transmitted or received. It is allowed any time thereafter, but any existing receive or
transmit activity will be lost, and all state machines
(Link integrity, Jabber, and Polarity Correction) return to their initial states. TEST must be held low for
a device reset to prevent entering a test for low power mode. During RESET, TxC continues without interruption (in Fujitsu mode both TxC and RxC run
continuously).
4.2 Low Power and High Impedance
Modes
When RESET is deasserted while both TEST and
JABD are held high, the 82503 enters its low power
and high impedance modes. The majority of internal
circuitry is powered down, and many inputs and outputs are three-stated. These pins are: APORT,
APOL/XSQ, LID, TPE/AUI, POLED, LILED, RTS,
LPBK, RxD, TxD, CRS and CDT. When either JABD
or TEST is deasserted, the device begins a power
on cycle which lasts less than 1 ms. During this cycle, all inputs are ignored and all transmissions are
disabled. If RTS is active when the device returns to
normal operation, the remainder of that packet fragment is not transmitted. Normal transmissions are
resumed at the start of the first complete data packet.
16
4.3 Diagnostic Loopback
This is a diagnostic test mode to help in fault isolation and detection. Serial NRZ data input on TxD is
Manchester encoded and then looped back through
the Manchester decoder (TMD) appearing at the
RxD output. Collision detect is asserted following
each transmission to simulate the SQE test. Output
cable drivers and input amplifiers are disconnected
from the controller interface pins while in this mode.
The link integrity and polarity fault detection functions are not inhibited by diagnostic loopback mode.
If otherwise enabled, they continue to function.
4.4 Customer Test Mode
(Continuous AUI/TPE Transmit)
In this mode, the 82503 continuously transmits data
without the intervention of a LAN controller. Transmission is at 10 MHz (11-bit pattern), and can occur
on either the TPE or AUI port. The jabber timer is
disabled in this mode, allowing users to easily test
the 10BASE-T harmonic content specification and
the quality of their analog front end design without
complex software exercisers.
Customer Test ModeÐand Low Power Mode are selected at the deassertion of RESET as shown in the
following table. (Note that the 82503 must be in nonloopback mode before it can enter the customer test
mode.)
82503
Table 3. Test and Low Power Mode Selection
RESET
TEST
JABD
TxLED(1)
RxLED(1)
COLED(1)
v
v
v
0
X
X
X
X
1
0
1
1
1
Cont Tx 10 MHz
1
1
X
X
X
Low Power
Mode Selected
Normal Mode
NOTE:
1. A standard LED connection to these pins is sufficient to pull them to a logic 1.
The port on which the continuous transmit appears
is determined by the APORT and TPE/AUI pins. If
automatic port selection is enabled (APORT e 1)
then the TPE port broadcasts the continuous transmit. If manual port selection is enabled (APORT e
0), then TPE/AUI selects the port (1 for TPE, 0 for
AUI). Test mode is disabled when TEST is deasserted and the device is reset.
5.0
APPLICATION EXAMPLE
5.1 Introduction
The 82503 is designed to work directly with the Intel
LAN controllers (82586, 82590, 82593, and 82596),
as well as AMD’s Am7990, National Semiconductor’s 8390, Western Digital’s 82C690, and Fujitsu’s
86950. The serial interface signals connect directly
between one of the aforementioned LAN controllers
and the 82503 without the need for external logic.
This example is targeted toward interfacing the
82503 to the Intel 82596 in a two-port (TPE/AUI)
application.
Terminating Resistors
The terminating resistors used across the receive
and collision pairs are recommended to be 78.7 X
g 1%.
Analog Front-End
The 82503 provides six TPE pins (TDH, TDH, TDL,
TDL, RD, and RD) that connect to the Analog Front
End through a resistor summing network (Figure 7).
AFE solutions can be made discretely or purchased
from several manufacturers. Two different solutions
are described in Application Note 356. The example
shown here uses a Pulse Engineering AFE package
PE65434 which includes EMI filter, isolation transformer, and common mode choke. The output of the
AFE connects directly to the 10BASE-T connector
(RJ-45).
Decoupling
It is recommended that 0.01 mF X7R and 0.001 mF
NPO decoupling capacitors be placed between the
VCCA and VCCD of the 82503 to VSSA and VSSD.
Clock Generation
5.2 Design Guidelines
AUI Pulse Transformer
In order to meet the 16V fault tolerance specification
of 802.3 a pulse transformer is recommended for the
transmit, receive and collision pairs. The transformer
should be placed between the TRMT, RCV, and
CLSN pairs of the 503, and the DO, DI, and CI pairs
respectively, of the AUI (DB-15 connector). The
pulse transformer should have a parallel inductance
of 75 mH minimum (100 mH recommended).
Several vendors stock such transformers. Two possible vendors are:
1. Pulse Engineering (P/N PE-64103)
2. Valor Electronics (P/N LT6003)
The clock input to the 82503 can be from a clock
oscillator or a crystal. If a clock oscillator is used, X1
should be driven, and X2 left floating. If a crystal
oscillator is used, refer to Section 3.1 for crystal
specifications.
A complete 82596/82503 TPE/AUI Ethernet Solution is shown at the end of this section.
5.3 Layout Guidelines
General
The analog section, as well as, the entire board itself
should conform to good high-frequency practices
and standards to minimize switching transients and
parasitic interaction between various circuits. To
achieve this, the following guidelines are presented.
17
82503
290421 – 7
Figure 8. Application Example Schematic
18
82503
Make power supply and ground traces as thick as
possible. This will reduce high-frequency cross coupling caused by the inductance of thin traces.
Connect logic and chassis ground together.
Separate and decouple all of the analog and digital
power supply lines.
Close signal paths to ground as close as possible to
their sources to avoid ground loops and noise cross
coupling.
Use high-loss magnetic beads on power supply distribution lines.
Crystal
The crystal should be adjacent to the 82503 and
trace lengths should be as short as possible. The X1
and X2 traces should be symmetrical.
82503 Analog Differential Signals
The differential signals from the 82503 to the transformers, analog front end, and the connectors
should be symmetrical for each pair and as short as
possible. Differential signal layout should be performed to a characteristic impedance of 78X (for
AUI) or 100X (for TPE).
As a general rule, the trace widths should be one to
three times the distance between the PCB layers to
eliminate excessive trace inductance.
The differential signals should also be isolated from
the high speed logic signals on the same layer as
well as on any sublayers of the PCB.
Group each of the circuits together, but keep them
separate from each other. Separate their grounds.
In layout, the circuitry from the connectors to the
filter network, should have the ground plane removed from beneath it. This will prevent ground
noise from being induced into the analog front end.
All trace bends should not exceed 45 degrees.
6.0
PACKAGE THERMAL
SPECIFICATIONS
The 82503 Dual Serial Transceiver is specified for
operation when case temperature (TC) is within the
range of 0§ C to a 85§ C. The case temperature can
be measured in any environment, to determine if the
82503 is within the specified operating range. The
case temperature should be measured at the center
of the top surface opposite the pins.
The acceptable operating ambient temperature (TA)
is guaranteed as long as TC is not violated. The ambient temperature can be calculated from the ija
and ijc from the following equations:
TJ e TC a P c ijc
TJ e TA a P c ija
TA e TC b P c (ija b ijc)
Values for ija and ijc are given in Table 4 for the 44lead PLCC and 44-lead QFP packages. Various values for ija at different airflows. Table 5 shows the
maximum TA allowable (without exceeding TC) at
various airflows.
Table 4. Thermal Resistance
(§ C/Watt) ijc and ija
ija vs AirflowÐft/min (m/s)
Package ijc 0 200
400
600
800 1000
(0) (1.01) (2.03) (3.04) (4.06) (5.07)
44-Lead 19 57
PLCC
48
43
41
39
37
44-Lead 26 98
QFP
94
78
70
66
64
Table 5. Maximum TA at Various Airflows
ija vs AirflowÐft/min (m/s)
Package
0
200
400
600
800
1000
(0) (1.01) (2.03) (3.04) (4.06) (5.07)
44-Lead
PLCC
66
71
73
74
75
76
44-Lead
QFP
49
51
59
63
65
66
19
82503
7.0
ELECTRICAL SPECIFICATIONS
AND TIMINGS
NOTICE: This is a production data sheet. The specifications are subject to change without notice.
*WARNING: Stressing the device beyond the ‘‘Absolute
Maximum Ratings’’ may cause permanent damage.
These are stress ratings only. Operation beyond the
‘‘Operating Conditions’’ is not recommended and extended exposure beyond the ‘‘Operating Conditions’’
may affect device reliability.
ABSOLUTE MAXIMUM RATINGS
Case Temperature Under Bias ÀÀÀÀÀÀÀ0§ C to a 85§ C
Storage Temperature ÀÀÀÀÀÀÀÀÀÀ b 65§ C to a 140§ C
All Output and Supply Voltages ÀÀÀÀÀ b 0.5V to a 7V
All Input Voltages ÀÀÀÀÀÀÀÀÀÀÀÀÀ b 1.0V to a 6.0V(1)
DC CHARACTERISTICS
Symbol
(TC e 0§ C to a 85§ C, VCC e 5V g 5%, VCCA e 5V g 5%)
Parameter
Max
Units
b 0.3
0.8
V
2.0
VCC
V
Input Leakage Current
g 10
mA
VOL(MOS)(3)
Output Low Voltage
0.45
V
IOL e 4 mA
VOH(MOS)
Output High Voltage
V
IOH e b 500 mA
VOL(LED)(4)
Output Low Voltage
V
IOL e 10 mA
VOH(LED)
Output High Voltage
V
IOH e b 500 mA
ILP
Leakage Current, Low
Power Mode(5)
mA
0.0V s VI s VCC
RDIFF
Input Differential Resistance(6)
10
kX
dc
VIDF(TPE)(7)
Input Differential Accept
Input Differential Reject
Input Differential Accept (XSQ)
Input Differential Reject (XSQ)
g 0.500
5 MHz s f s 10 MHz
g 0.180
VP
VP
VP
VP
13
X
lILOADl e 25 mA
g 1.5
g 0.160
VP
VP
g 1.20
V
VIL(TTL)(2)
Input Low Voltage
VIH(TTL)(2)
Input High Voltage
ILI(2)
Min
3.9
0.45
3.9
g 10
(Note 8)
RS(TPE)(8)
Output Source Resistance
VIDF(AUI)(9)
Input Differential Accept
Input Differential Reject
g 0.300
Output Differential Voltage
g 0.450
VODF(AUI)(10)
g 3.1
g 0.300
6
g 3.1
Test Conditions
0.0V s VI s VCC, RESET e 1
NOTES:
1. The voltage levels for RCV, CLSN, and RD pairs are b0.75V to a 8.5V.
2. TTL Input Pins: TxD, RTS, TPE/AUI, APORT, APOL/XSQ, LID, CS0, CS1, LPBK, JABD, TEST, RESET.
3. MOS Output Pins: TxC, RxD, RxC, CRS, CDT.
4. LED Pins: TPE/AUI, TxLED, RxLED, COLED, POLED, LILED. VOL measured 10 ns after falling edge of TxC.
5. Pins: APORT, APOL/XSQ, LID, TPE/AUI, POLED, LILED, RTS, LPBK, RxD, TxD, CRS,
CDT, CS0, CS1, JABD, TEST, and RESET.
6. Pins: RD to RD, RCV to RCV, and CLSN to CLSN.
7. TPE Input Pins: RD, and RD. See Section 3.3.4 and Section 3.3.5.
8. Typically it is b4.5 dB below normal squelch level.
9. TPE Output Pins: TDH, TDH, TDL, and TDL. RS measures VCC or VSS to Pin.
10. AUI Input Pins: RCV, and CLSN pairs.
11. AUI Output Pins: TRMT pair.
20
82503
DC CHARACTERISTICS
Symbol
(TC e 0§ C to a 85§ C, VCC e 5V g 5%, VCCA e 5V g 5%) (Continued)
Parameter
Min
Max
Units
IOSC(AUI) AUI Output Short Circuit Current
g 150
mA
VU(AUI)
b 100
mV
Output Differential Undershoot
VODI(AUI) Differential Idle Voltage(11)
Test Conditions
Short Circuit to VCC or GND
g 40
mV
ICC(HOT)
Power Supply Current(12)
65
mA
APORT e 1
ICC
Power Supply Current
75
mA
APORT e 1
ICC
Power Supply Current
60
mA
APORT e 0
ICCSB
Standby Supply Current(13)
1
mA
Low Power Mode, 20 mA Typical
PD (HOT) Power Dissipation(12)
0.38
W
APORT e 1, Continuous Transmission
on AUI
PD
Power Dissipation
0.40
W
APORT e 1, Continuous Transmission
on AUI
PDSB
Standby Power Dissipation(13)
5.25
mW
Low Power Mode, 105 mW Typical
CIN(14)
Input Capacitance
10
pF
at f e 1 MHz
NOTES:
11. Measured 8.0 ms after last positive transition of data packet.
12. ICC HOT measurements made at TC e a 85§ C. Additionally, TRMT, TRMT, TDH, TDH, TDL, TDL are loaded with 20 pF
and load resistors removed.
13. Pins CS0 and CS1 connected to VCC or VSS through a 2.5 kX (or less) resistor. ICCSB is typically at 20 mA after 30s
from power down assertionÐnot tested.
14. Characterized, not tested. (Controller interface and mode pins only.)
AC TIMING CHARACTERISTICS
290421 – 9
290421 – 8
Figure 9. MOS Input Voltage Levels
(TTL Compatible) for Timing Measurements
(TxD, RTS, TPE/AUI, APORT, APOL/XSQ,
LID, LPBK, JABD, TEST, and RESET).
290421 – 10
Figure 11. Voltage Levels for Differential Input
Timing Measurements (RCV and CLSN Pairs).
Figure 10. Voltage Levels for MOS Level
Output Timing Measurements
(TxC, RxD, RxC, CRS, and CDT).
290421 – 11
Figure 12. Voltage Levels for TRMT Pair
Output Timing Measurements.
21
82503
AC TIMING CHARACTERISTICS (Continued)
290421 – 13
Figure 14. Voltage Levels for Differential Input
Timing Measurements (RD Pair).
290421 – 12
Figure 13. Voltage Levels for
TDH, TDL, TDH, and TDL.
AC MEASUREMENT CONDITIONS
1. TC e 0§ C to a 85§ C, VCC e 5V g 5%.
2. The AC MOS, TTL and differential signals are referred to in Figures, 8, 9, 10, 11, 12, and 13.
3. AC loads
a. MOS: 20 pF total capacitance to ground.
b. AUI Differential: a 10 pF total capacitance from each terminal to ground and a load resistor of 78X g 1%
in parallel with a 27 mH g 1% inductor between terminals.
c. TPE: 20 pF total capacitance to ground.
4. All parameters become valid 200 ms after the supply voltage and input clock has stabilized, or after RESET
deasserts.
CLOCK TIMING (15)
Symbol
Parameter
Min
Typ
Max
Units
t1
X1 Cycle Time
49.995
t2
X1 Fall Time
t3
X1 Rise Time
t4
X1 Low Time
15
ns
t5
X1 High Time
15
ns
50.005
ns
5
ns
5
ns
NOTE:
15. Refers to External Clock Input.
290421 – 14
Figure 15. X1 Input Voltage Levels for Timing Measurements
22
82503
Controller Interface Timings (Intel Mode)
TRANSMIT TIMINGS (Intel)
Symbol
Parameter
t10
TxC Cycle Time
t11
TxC High/Low Time
t12
TxC Rise/Fall Time
t13
TxD and RTS Rise/Fall Time
t14
TxD Setup Time to TxC
t15
t16
t17
Min
Typ
99.99
v
TxD Hold Time from TxCv
RTS Setup Time to TxCv
RTS Hold Time from TxCv
Max
Units
100.01
ns
40
ns
5
ns
10
ns
45
ns
0
ns
45
ns
0
ns
290421 – 15
Figure 16. Transmit Timing (Intel)
23
82503
RECEIVE TIMING (Intel)
Symbol
Parameter
Min
Typ
100
Max
Units
t20
RxC Cycle Time
96
t21
RxC High Time
36
t22
RxC Low Time
40
t23
RxC Rise/Fall Time
t24
RxC Delay from CRS
t25
RxD Rise/Fall Time
t26
RxD Setup from RxC
ns
RxD Hold from RxC
v
v
30
t27
30
ns
t28
CRS Deassertion Hold Time from RxC High
10
v
ns
ns
ns
1100
5
ns
1400
ns
5
ns
40
ns
290421 – 16
Figure 17. Receive Timing (Intel)
24
82503
Controller Interface Timings (National Mode)
TRANSMIT TIMINGS (National)
Symbol
Parameter
Min
Typ
Max
Units
100.01
ns
t30
TXC Cycle Time(16)
99.99
t31
TXC High/Low Time
40
t32
TXC Rise/Fall Time at 20% to 80%
t33
TXD Setup Time to TXC
20
ns
t34
TXD Hold Time from TXC
0
ns
t35
t36
u
u
TXE Setup Time to TXCu
TXE Hold Time from TXCu
50
ns
5
ns
20
ns
0
ns
NOTE:
16. All delay and width measurements on TxC are made at 1.5V.
290421 – 17
Figure 18. Transmit Timing (National)
25
82503
RECEIVE TIMINGS (National)
Symbol
Parameter
Min
Typ
Max
Units
60
ns
t40
RxC Cycle Time
96
100
t41
RxC High/Low Time(17)
40
50
t42
RxC Rise/Fall Time at 20% to 80%
5
ns
t43
RXD Rise/Fall Time at 20% to 80%
5
ns
t44
RXD Setup Time to RxC
t45
RXD Hold Time from RxC
t46
RxC Delay from CRS
t47
RxC Continuing Beyond CRS
u
u
ns
30
ns
20
ns
u
v
1400
ns
5
cycles
NOTE:
17. All delay and width measurements on RXC are made at 1.5V.
290421 – 18
Figure 19. Receiving Timings (National)
26
82503
Controller Interface Timing (AMD Mode)
TRANSMIT TIMINGS(18) (AMD)
Symbol
t50
Parameter
Min
TCLK Cycle Time
Typ
99.99
(@
Max
Units
100.01
ns
t51
TCLK High Time
0.8V to 2.0V)
45
50
58
ns
t52
TCLK Low Time ( @ 2.0V to 0.8V)
45
50
58
ns
2.5
5
t53
TCLK Rise/Fall Time
t54
TX Setup Time to TCLK
t55
t56
t57
(@
0.8V to 2.0V)
u
TX Hold Time from TCLKu
TENA Setup Time to TCLKu
TENA Hold Time from TCLKu
ns
20
ns
5
ns
20
ns
5
ns
NOTE:
18. Delay times for TX, TENA, and TCLK are measured from 0.8V for falling edges, and 2.0V for rising edges.
290421 – 19
Figure 20. Transmit Timings (AMD)
27
82503
RECEIVE TIMINGS(19) (AMD)
Symbol
Parameter
Min
Typ
Max
Units
t60
RCLK Cycle Time
96
100
ns
t61
RCLK High Time ( @ 0.8V to 2.0V)
38
50
ns
t62
RCLK Low Time ( @ 2.0V to 0.8V)
38
t63
RCLK Rise/Fall Time ( @ 0.8V to 2.0V)
t64
RX Rise/Fall Time ( @ 0.8V to 2.0V)
t65
RX Hold time from RCLK
t66
u
RX Setup Time to RCLKu
t67
RENA Deassertion Hold Time from RCLK
t68
RCLK Delay from RENA
50
ns
2.5
5
ns
2.5
5
ns
10
ns
45
u
40
ns
50
u
80
ns
450
ns
NOTE:
19. Delay times for RX, RENA, and RCLK are measured from 0.8V for falling edges and 2.0V for rising edges.
290421 – 20
Figure 21. Receive Timings (AMDÐStart of Frame)
290421 – 21
Figure 22. Receive Timings (AMDÐEnd of Frame)
28
82503
Controller Interface Timings (Fujitsu Mode)
TRANSMIT TIMINGS (Fujitsu)
Symbol
Parameter
t70
TCKN Cycle Time
t71
TCKN High/Low Time(20)
t72
TCKN Rise/Fall Time at 20% to 80%
t73
TXD Setup Time to TCKN
t74
t75
t76
v(20)
TXD Hold Time from TCKNv(20)
TEN Setup Time to TCKNv(20)
TEN Hold Time from TCKNv(20)
Min
Typ
99.99
40
Max
Units
100.01
ns
5
ns
50
ns
20
ns
0
ns
20
ns
0
ns
NOTE:
20. Timing measurements are referenced at 1.5V level.
290421 – 22
Figure 23. Transmit Timings (Fujitsu)
29
82503
RECEIVE TIMINGS (Fujitsu)
Symbol
Parameter
Min
Typ
t80
RCKN Cycle Time
96
100
t81
RCKN High/Low Time(21)
35
50
t82
RCKN Rise/Fall Time at 20% to 80%
t83
RXD Setup Time from RCKN
20
t84
v(21)
RXD Hold Time from RCKNv(21)
t85
XCD Assertion Hold Time from RCKN
v(21)
XCD Deassertion Hold Time from RCKNv(21)
XCD Deassertion Setup Time from RCKNv(21)
RCKN Delay from XCDu(21)
0
t86
t87
t88
Max
Units
ns
60
ns
5
ns
ns
10
ns
10
ns
120
80
ns
130
ns
1400
ns
NOTE:
21. Timing measurements are referenced at 1.5V.
290421 – 23
Figure 24. Receive Timings (FujitsuÐStart of Frame)
290421 – 24
Figure 25. Receive Timings (FujitsuÐEnd of Frame)
30
82503
TPE Timings
TPE TRANSMIT TIMINGS
Symbol
Parameter
Max
Units
2
bits
TxD to TD Steady State Propagation Delay
400
ns
TxD to TD Startup Delay
600
ns
1.5
3
ns
2
5
ns
t90
TxD to TD Bit Loss at Start of Packet
t91
t92
(@
Min
VCC/2)
Typ
t93
TDH and TDL Pairs Edge Skew
t94
TDH and TDL Pairs Rise/Fall Times ( @ 0.5V to VCC b 0.5V)
t95
TDH and TDL Pairs Bit Cell Center to Center
99
100
101
ns
t96
TDH and TDL Pairs Bit Cell Center to Boundary
49
50
51
ns
t97
TDH and TDL Pairs Return to Zero from Last TDH
t98
Link Test Pulse Width
t99
Last TD Activity to Link Test Pulse
t100
Link Test Pulse to Data Separation
u
250
400
ns
100
102
ns
8
13
24
ms
190
200
98
ns
290421 – 25
Figure 26. TPE Transmit Timings (Start of Frame)
290421 – 26
Figure 27. TPE Transmit Timings (End of Frame)
31
82503
290421 – 27
Figure 28. TPE Transmit Timings (Link Test Pulse)
TPE RECEIVE TIMINGS
Symbol
Parameter
Min
4
Typ
Max
Units
19
bits
1
bits
t105
RD to RxD Bit Loss at Start of Packet
t106
RD to RxD Invalid Bits Allowed at Start of Packet
t107
RD to RxD Steady State Propagation Delay
400
ns
t108
RD to RxD Start UP Delay
2.4
ms
t109
RD Pair Bit Cell Center Jitter
g 13.5
ns
t110
RD Pair Bit Cell Boundary Jitter
g 13.5
ns
t111
RD Pair Held High from Last Valid Positive Transition
400
ns
t112
CRS Assertion Delay (Intel, NS, and Fuji Mode)
(AMD Mode)
700
1500
ns
ns
t113
CRS Deassertion Delay
450
ns
230
290421 – 28
Figure 29. TPE Receive Timings (Start of Frame)
32
82503
290421 – 29
Figure 30. TPE Receive Timings (End of Frame)
TPE COLLISION TIMINGS
Symbol
Parameter
Min
Typ
Max
Units
t115
Onset of Collision (RD Pair and RTS Active) to CDT Assert
900
ns
t116
End of Collision (RD Pair or RTS Inactive) to CDT Deassert
900
ns
t117
CDT Assert to RxD Sourced from RD Pair
900
ns
t118
CDT Deassert (RD Pair Inactive) to RxD Sourced from TxD
900
ns
290421 – 30
Figure 31. TPE Collision Timings (Start of Collision)
33
82503
290421 – 31
Figure 32. TPE Collision Timings (End of Collision)
TPE LINK INTEGRITY TIMINGS
Symbol
Parameter
Min
Typ
Max
Units
t120
Last RD Activity to Link Fault (Link Loss Timer)
50
100
150
ms
t121
Minimum Received Linkbeat Separation(20)
2
5
7
ms
t122
Maximum Received Linkbeat Separation(21)
25
50
150
ms
NOTES:
20. Linkbeats closer in time to this value are considered noise, and are rejected.
21. Linkbeats further apart in time than this value are not considered consecutive, and are rejected.
290421 – 32
Figure 33. TPE Link Integrity Timings
34
82503
AUI Timings
AUI TRANSMIT TIMINGS
Symbol
Parameter
Min
Typ
Max
Units
200
ns
3
5
ns
100
100.5
ns
50.5
ns
t125
TxD to TRMT Pair Steady State Propagation Delay
t126
TRMT Pair Rise/Fall Times
t127
Bit Cell Center to Bit Cell Center of TRMT Pair
99.5
t128
Bit Cell Center to Bit Cell Boundary of TRMT Pair
49.5
50
t129
TRMT Pair Held at Positive Differential at Start of Idle
200
t130
TRMT Pair Return to s 40 mV from Last Positive Transition
ns
8.0
ms
290421 – 33
Figure 34. AUI Transmit Timings
AUI RECEIVE TIMINGS
Symbol
Parameter
Min
Typ
Max
Units
t135
RCV Pair Rise/Fall Times
10
ns
t136
RCV Pair Bit Cell Center Jitter in Preamble
g 12
ns
t137
RCV Pair Bit Cell Center/Boundary Jitter in Data
g 18
t138
RCV Pair Idle Time after Transmission
t139
RCV Pair Return to Zero from Last Positive Transition
t140
CRS Assertion Delay (Intel, National, Fujitsu Modes)
(AMD Mode)
t141
CRS Deassertion Delay
t142
CRS Inhibited after Frame Transmission
8
160
ns
100
1050
4
ns
ms
4.3
ns
ns
350
ns
5
ms
290421 – 34
Figure 35. AUI Receive Timings
35
82503
AUI COLLISION TIMINGS
Symbol
Parameter
Min
Typ
80
Max
Units
118
ns
10
ns
70
ns
t145
CLSN Pair Cycle Time
t146
CLSN Pair Rise/Fall Times
t147
CLSN Pair Return to Zero from Last Positive Transition
160
t148
CLSN Pair High/Low Times
35
t149
CDT Assertion Time
75
ns
t150
CDT Deassertion Time
300
ns
t151
CRS Deassertion Time (Intel Mode Only, RCV Pair Idle)
450
ns
ns
290421 – 35
Figure 36. AUI Collision Timings
AUI NOISE FILTER TIMINGS
Symbol
Parameter
Min
(@
t152
RCV Pair Noise Filter Pulse Width Accept
t153
CLSN Pair Noise Filter Pulse Width Accept ( @ b 285 mV)
b 285 mV)
Typ
36
Units
25
ns
25
ns
290421 – 36
Figure 37. AUI Noise Filter Timings
Max
82503
LOOPBACK TIMINGS
Symbol
Parameter
Min
Typ
Max
Units
t155
TxD to RxD Bit Loss at Start of Packet
16
bits
t156
TxD to RxD Steady State Propagation Delay
600
ns
t157
TxD to RxD Startup Delay
2.2
ms
t158
SQE Test Wait Time
0.6
1.2
1.6
ms
t159
SQE Test Duration
0.5
0.8
1.5
t160
LPBK Setup/Hold Times to RTS(22)
1.0
ms
ms
NOTE:
22. Guarantees proper processing of transmitted packets. Violation of this specification will not result in spurious data transmission. Incoming data packets occuring during transitions on LPBK will not be accepted.
290421 – 37
Figure 38. Loopback Timings
37
82503
JABBER TIMINGS
Symbol
Parameter
Min
Typ
Max
Units
t165
Maximum Length Transmission before Jabber Fault (TPE)
20
25
150
ms
t166
Maximum Length Transmission before Jabber Fault (AUI)
10
13
18
ms
t167
Minimum Idle Time to Clear Jabber Function
250
420
750
ms
290421 – 38
Figure 39. Jabber Timings
LED TIMINGS
Symbol
Parameter
Min
t170
TxLED, RxLED, COLED On Time
50
Typ
Max
Units
450
ms
t171
TxLED, RxLED, COLED Off Time
50
ms
t172
LILED On Time
50
ms
t173
LILED Off Time
100
ms
290421 – 39
Figure 40. LED Timings
38
82503
MODE TIMINGS(23, 24)
Symbol
Parameter
Min
v
u
Typ
Max
Units
t175
Mode Pins Setup to RTS
100
ms
t176
Mode Pins Hold from RTS
100
ms
t177
Mode Pins Setup to RD Active(25)
100
ms
t178
Mode Pins Hold from RD Active(25)
100
ms
NOTES:
23. Guarantees Proper processing of data packets. Violation of these specifications will not affect the integrity of the network.
24. Mode pins are: APORT, APOL/XSQ, LID, JABD, and TPE/AUI.
25. Any data received within 100 ms of a mode transmission will be considered invalid.
290421 – 53
Figure 41. Mode Timings
39
82503
RESET, TEST, AND LOW POWER MODE TIMINGS
Symbol
Parameter
Min
v
t180
TEST and JABD Setup Time to RESET
t181
RESET Pulse Width
t182
Low Power Mode Deactivation from TEST and JABD
Typ
Max
Units
50
ns
300
ns
v
1
ms
290421 – 41
Figure 42. Reset Timings (Test Mode)
290421 – 43
Figure 43. Reset Timings (Start of Low Power Mode)
290421 – 42
Figure 44. Reset Timings (End of Low Power Mode)
40
82503
PACKAGE DIMENSIONS
PLASTIC LEADED CHIP CARRIER
290421 – 45
Figure 45. Principle Dimensions and Data
290421 – 46
Figure 46. Molded Details
41
82503
290421 – 47
Figure 47. Terminal Details
290421 – 48
Figure 48. Standard Package Bottom View (Tooling Option 1)
42
82503
290421 – 49
Figure 49. Standard Package Bottom View (Tooling Option II)
290421 – 50
Figure 50. Detail J. Terminal Detail
43
82503
290421 – 51
Figure 51. Detail L. Terminal Details
NOTES:
The above diagrams use a 20-lead PLCC package to show symbols for package dimensions. The table below indicates
dimensions in mm that are specific to the 44-lead PLCC package.
1. All dimensions and tolerances conform to ANSI Y14.5M-1982.
2. Datum plane ÐHÐ located at top of mold parting line and coincident with top of lead, where lead exits plastic body.
3. Datums D – E and F– G to be determined where center leads exit plastic body at datum plane ÐHÐ.
4. To be determined at seating plane ÐCÐ.
5. Dimensions D1 and E1 do not include mold protrusion.
6. Pin 1 identifier is located within one of the two defined zones.
7. Locations to datum ÐAÐ and ÐBÐ to be determined at plane ÐHÐ.
8. These two dimensions determine maximum angle of the lead for certain socket applications. If unit is intended to be
socketed, it is advisable to review these dimensions with the socket supplier.
9. Controlling dimension, inch.
10. All dimensions and tolerances include lead trim offset and lead plating finish.
11. Tweezing surface planarity is defined as the furthest any lead on a side may be from the datum. The datum is established by touching the outermost lead on that side and parallel to D –E or F –G.
Symbol
44
Description
Min
Max
A
Overall Height
4.19
4.57
A1
Distance from Lead Shoulder to Seating Plane
2.29
3.05
D
Overall Package Dimension
17.4
17.7
D1
Plastic Body Dimension
16.5
16.7
D2
Foot Print
15.0
16.0
E
Overall Package Dimension
17.4
17.7
E1
Plastic Body Dimension
16.5
16.7
E2
Foot Print
15.0
16.0
CP
Seating Plans Coplanarity
0.00
0.10
TCP
Tweezing Coplanarity
0.00
0.10
LT
Lead Thickness
0.23
0.38
82503
44-LEAD QUAD FLATPACK PACKAGE
290421 – 52
Figure 52. 44-Lead Quad Flatpack Package
Symbol
Description
Min
Nom
Max
A
Package Height
2.35
A1
Stand Off
B
Lead Width
0.2
0.3
0.4
C
Lead Thickness
0.1
0.15
0.2
D1
Package Body
E1
Package Body
e1
Lead Pitch
0.65
0.8
0.95
D
Terminal Dimension
12.0
12.4
12.8
E
Terminal Dimension
12
12.4
12.8
L1
Foot Length
0.38
0.58
0.78
Y
Coplanarity
T
Lead Angle
0
0.60
10
10
0.1
0
10§
NOTE:
Unless otherwise specified, all units are in millimeters.
45