MOSEL V55C2128164VT

MOSEL VITELIC
V55C2128164V(T/B)
128Mbit LOW-POWER SDRAM
2.5 VOLT, TSOP II / BGA PACKAGE
8M X 16
PRELIMINARY
6
7PC
7
8PC
10
System Frequency (fCK)
166 MHz
143 MHz
143 MHz
125 MHz
100MHz
Clock Cycle Time (tCK3)
6 ns
7 ns
7 ns
8 ns
10 ns
Clock Access Time (tAC3) CAS Latency = 3
5.4 ns
5.4 ns
5.4 ns
6 ns
7 ns
Clock Access Time (tAC2) CAS Latency = 2
5.4 ns
5.4 ns
6 ns
6 ns
8 ns
Clock Access Time (tAC1) CAS Latency = 1
19 ns
19 ns
19 ns
19 ns
22 ns
■
■ Programmable Power Reduction Feature by partial array activation during Self-Refresh
■ Operating Temperature Range
Commercial (0°C to 70°C)
Features
■ 4 banks x 2Mbit x 16 organization
■ High speed data transfer rates up to 166 MHz
■ Full Synchronous Dynamic RAM, with all signals
referenced to clock rising edge
■ Single Pulsed RAS Interface
■ Data Mask for Read/Write Control
■ Four Banks controlled by BA0 & BA1
■ Programmable CAS Latency:1, 2, 3
■ Programmable Wrap Sequence: Sequential or
Interleave
■ Programmable Burst Length:
1, 2, 4, 8, Full page for Sequential Type
1, 2, 4, 8 for Interleave Type
■ Multiple Burst Read with Single Write Operation
■ Automatic and Controlled Precharge Command
■ Random Column Address every CLK (1-N Rule)
■ Power Down Mode and Clock Suspend Mode
■ Deep Power Mode
■ Auto Refresh and Self Refresh
■ Refresh Interval: 4096 cycles/64 ms
■ Available in 54-ball FBGA, with 9x6 ball array
with 3 depupulated rows, 9x8 mm and 54 pin
TSOP II
■ VDD=2.5V, VDDQ=1.8V
Extended (-25°C to +85°C)
Device Usage Chart
Operating
Temperature
Range
Package Outline
T/B
6
7PC
7
8PC
10
Temperature
Mark
0°C to 70°C
•
•
•
•
•
•
Commercial
-25°C to 85°C
•
•
•
•
•
•
Extended
V55C2128164V(T/B) Rev. 1.2 August 2002
Access Time (ns)
1
V55C2128164V(T/B)
MOSEL VITELIC
V 55 C 2 12816
Mosel Vitelic
Manufactured
BGA
Pkg.
C=CMOS Family
Pin Count
B
Speed
6 ns
7 ns
8 ns
10 nsComponent
Device
Number
Low Power
Synchronous DRAM
Description
4 S X B
Package
2.5V Supply Voltage
54
128Mb(4K Refresh)
4 Banks
Component Rev Level
A = 0.14um
S=SSTL
60 Pin WBGA PIN CONFIGURATION
Top View
Pin Configuration for x16 devices:
1
2
3
7
8
9
VSS DQ15 VSSQ
A
VDDQ DQ0
VDD
DQ14 DQ13 VDDQ
B
VSSQ DQ2
DQ1
DQ12 DQ11 VSSQ
C
VDDQ DQ4
DQ3
DQ10 DQ9 VDDQ
D
VSSQ DQ6
DQ5
DQ8
NC
VSS
E
VDD LDQM DQ7
UDQM CLK
CKE
F
CAS
RAS
WE
NC
A11
A9
G
BA0
BA1
CS
A8
A7
A6
H
A0
A1
A10
VSS
A5
A4
J
A3
A2
VDD
< Top-view >
V55C2128164V(T/B) Rev.1.2 August 2002
2
V55C2128164V(T/B)
MOSEL VITELIC
V 55 C 2 12816 4 S X T
Mosel Vitelic
Manufactured
Low Power
Synchronous DRAM
Description
Pkg.
Speed
6 ns
7 ns
8 ns
10 ns Component
Device
Number
C=CMOS Family
Pin Count
Package
2.5V Supply Voltage
TSOP-II
T
54
8Mx16(4K Refresh)
4 Banks
Component Rev Level
A = 0.14um
S=STTL
54 Pin Plastic TSOP-II
PIN CONFIGURATION
Top View
VCC
I/O1
VCCQ
I/O2
I/O3
VSSQ
I/O4
I/O5
VCCQ
I/O6
I/O7
VSSQ
I/O8
VCC
LDQM
WE
CAS
RAS
CS
BA0
BA1
A10
A0
A1
A2
A3
VCC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
V55C2128164V(T/B) Rev. 1.2 August 2002
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
Pin Names
VSS
I/O16
VSSQ
I/O15
I/O14
VCCQ
I/O13
I/O12
VSSQ
I/O11
I/O10
VCCQ
I/O9
VSS
NC
UDQM
CLK
CKE
NC
A11
A9
A8
A7
A6
A5
A4
VSS
3
CLK
Clock Input
CKE
Clock Enable
CS
Chip Select
RAS
Row Address Strobe
CAS
Column Address Strobe
WE
Write Enable
A0–A11
Address Inputs
BA0, BA1
Bank Select
I/O1–I/O16
Data Input/Output
LDQM, UDQM
Data Mask
VCC
Power (+2.5V)
VSS
Ground
VCCQ
Power for I/O’s (+1.8V)
VSSQ
Ground for I/O’s
NC
Not connected
V55C2128164V(T/B)
MOSEL VITELIC
Description
The V55C2128164V(T/B) is a four bank Synchronous DRAM organized as 4 banks x 2Mbit x 16. The
V55C2128164V(T/B) achieves high speed data transfer rates up to 166 MHz by employing a chip architecture
that prefetches multiple bits and then synchronizes the output data to a system clock
All of the control, address, data input and output circuits are synchronized with the positive edge of an externally supplied clock.
Operating the four memory banks in an interleaved fashion allows random access operation to occur at
higher rate than is possible with standard DRAMs. A sequential and gapless data rate of up to 166 MHz is
possible depending on burst length, CAS latency and speed grade of the device.
Signal Pin Description
Pin
Type
Signal
Polarity
Function
CLK
Input
Pulse
Positive
Edge
The system clock input. All of the SDRAM inputs are sampled on the rising edge of the
clock.
CKE
Input
Level
Active High Activates the CLK signal when high and deactivates the CLK signal when low, thereby
initiates either the Power Down mode or the Self Refresh mode.
CS
Input
Pulse
Active Low CS enables the command decoder when low and disables the command decoder when
high. When the command decoder is disabled, new commands are ignored but previous
operations continue.
RAS, CAS
WE
Input
Pulse
Active Low When sampled at the positive rising edge of the clock, CAS, RAS, and WE define the
command to be executed by the SDRAM.
A0 - A11
Input
Level
—
During a Bank Activate command cycle, A0-A11 defines the row address (RA0-RA11)
when sampled at the rising clock edge.
During a Read or Write command cycle, A0-An defines the column address (CA0-CAn)
when sampled at the rising clock edge.CAn depends from the SDRAM organization:
• 8M x 16 SDRAM CA0–CA8.
In addition to the column address, A10(=AP) is used to invoke autoprecharge operation
at the end of the burst read or write cycle. If A10 is high, autoprecharge is selected and
BA0, BA1 defines the bank to be precharged. If A10 is low, autoprecharge is disabled.
During a Precharge command cycle, A10(=AP) is used in conjunction with BA0 and BA1
to control which bank(s) to precharge. If A10 is high, all four banks will BA0 and BA1 are
used to define which bank to precharge.
BA0,
BA1
Input
Level
—
Selects which bank is to be active.
DQx
Input
Output
Level
—
Data Input/Output pins operate in the same manner as on conventional DRAMs.
LDQM
UDQM
Input
Pulse
Active High The Data Input/Output mask places the DQ buffers in a high impedance state when sampled high. In Read mode, DQM has a latency of two clock cycles and controls the output
buffers like an output enable. In Write mode, DQM has a latency of zero and operates as
a word mask by allowing input data to be written if it is low but blocks the write operation
if DQM is high.
VCC, VSS Supply
VCCQ
VSSQ
Supply
Power and ground for the input buffers and the core logic.
—
V55C2128164V(T/B) Rev. 1.2 August 2002
—
Isolated power supply and ground for the output buffers to provide improved noise
immunity.
4
V55C2128164V(T/B)
MOSEL VITELIC
Operation Definition
All of SDRAM operations are defined by states of control signals CS, RAS, CAS, WE, and DQM at the
positive edge of the clock. The following list shows the thruth table for the operation commands.
Device
State
CKE
n-1
CKE
n
CS
RAS
CAS
WE
DQM
A0-9,
A11
A10
BS0
BS1
Idle3
H
X
L
L
H
H
X
V
V
V
Active3
H
X
L
H
L
H
X
V
L
V
Active
3
H
X
L
H
L
H
X
V
H
V
Write
Active
3
H
X
L
H
L
L
X
V
L
V
Write with Autoprecharge
Active3
H
X
L
H
L
L
X
V
H
V
Row Precharge
Any
H
X
L
L
H
L
X
X
L
V
Precharge All
Any
H
X
L
L
H
L
X
X
H
X
Mode Register Set
Idle
H
X
L
L
L
L
X
V
V
V
No Operation
Any
H
X
L
H
H
H
X
X
X
X
Device Deselect
Any
H
X
H
X
X
X
X
X
X
X
Auto Refresh
Idle
H
H
L
L
L
H
X
X
X
X
Self Refresh Entry
Idle
H
L
L
L
L
H
X
X
X
X
Idle
(Self Refr.)
H
X
X
X
L
H
L
H
H
X
X
X
X
X
Idle
Active4
H
X
X
X
H
L
L
H
H
X
X
X
X
X
Any
(Power
Down)
H
X
X
X
L
H
L
H
H
L
X
X
X
X
Data Write/Output Enable
Active
H
X
X
X
X
X
L
X
X
X
Data Write/Output Disable
Active
H
X
X
X
X
X
H
X
X
X
Idle
H
L
L
H
H
L
H
X
X
X
Deep powerDown
L
H
X
X
X
X
H
X
X
X
Operation
Row Activate
Read
Read w/Autoprecharge
Self Refresh Exit
Power Down Entry
Power Down Exit
Deep Pwoer Down Entry
Deep Pwoer Down Exit
Notes:
1. V = Valid , x = Don’t Care, L = Low Level, H = High Level
2. CKEn signal is input level when commands are provided, CKEn-1 signal is input level one clock before the commands
are provided.
3. These are state of bank designated by BS0, BS1 signals.
4. Power Down Mode can not entry in the burst cycle.
5. After Deep Power Down mode exit a full new initialization of memory device is mandatory
V55C2128164V(T/B) Rev. 1.2 August 2002
5
V55C2128164V(T/B)
MOSEL VITELIC
rameters to be set as shown in the previous table.
Power On and Initialization
The default power on state of the mode register is
supplier specific and may be undefined. The
following power on and initialization sequence
guarantees the device is preconditioned to each
users specific needs. Like a conventional DRAM,
the Synchronous DRAM must be powered up and
initialized in a predefined manner. During power on,
all VCC and VCCQ pins must be built up
simultaneously to the specified voltage when the
input signals are held in the “NOP” state. The power
on voltage must not exceed VCC+0.3V on any of
the input pins or VCC supplies. The CLK signal
must be started at the same time. After power on,
an initial pause of 200 µs is required followed by a
precharge of both banks using the precharge
command. To prevent data contention on the DQ
bus during power on, it is required that the DQM and
CKE pins be held high during the initial pause
period. Once all banks have been precharged, the
Mode Register and Low Power Mode Register Set
Command must be issued to initialize the Mode
Register. A minimum of two Auto Refresh cycles
(CBR) are also required.These may be done before
or after programming the Mode Register. Failure to
follow these steps may lead to unpredictable startup modes.
Low Power Mode Register
The Low Power Mode Register controls functions
beyond those controlled by the Mode Register.
These additional functions are unique to the LowPower DRM and includes a Refresh Period field
(TCR) for temperature compensated self-refresh
and a Partial-Array Self-Refresh field (PAS). The
PASR field is used to specify whether only one
quarter (bank 0), one half (bank 0+1) or all banks of
the SDRAM array are enabled. Disabled banks will
not be refreshed in Self-Refresh mode and written
data will be lost. When only bank 0 is selected, it’s
possible to partially select only half or mone quarter
of bank 0. The TCR field has four entries to set Refresh Period during self-refresh depending on the
case temperature of the Low power RAM. It’s required during the initialization seuqence and can be
modified when the part id idle.
Read and Write Operation
When RAS is low and both CAS and WE are high
at the positive edge of the clock, a RAS cycle starts.
According to address data, a word line of the selected bank is activated and all of sense amplifiers associated to the wordline are set. A CAS cycle is
triggered by setting RAS high and CAS low at a
clock timing after a necessary delay, tRCD, from the
RAS timing. WE is used to define either a read
(WE = H) or a write (WE = L) at this stage.
SDRAM provides a wide variety of fast access
modes. In a single CAS cycle, serial data read or
write operations are allowed at up to a 125 MHz
data rate. The numbers of serial data bits are the
burst length programmed at the mode set operation,
i.e., one of 1, 2, 4, 8. Column addresses are segmented by the burst length and serial data accesses
are done within this boundary. The first column address to be accessed is supplied at the CAS timing
and the subsequent addresses are generated automatically by the programmed burst length and its
sequence. For example, in a burst length of 8 with
interleave sequence, if the first address is ‘2’, then
the rest of the burst sequence is 3, 0, 1, 6, 7, 4, and
5.
Programming the Mode Register
The Mode register designates the operation
mode at the read or write cycle. This register is divided into 4 fields. A Burst Length Field to set the
length of the burst, an Addressing Selection bit to
program the column access sequence in a burst cycle (interleaved or sequential), a CAS Latency Field
to set the access time at clock cycle and a Operation mode field to differentiate between normal operation (Burst read and burst Write) and a special
Burst Read and Single Write mode. The mode set
operation must be done before any activate command after the initial power up. Any content of the
mode register can be altered by re-executing the
mode set command. All banks must be in precharged state and CKE must be high at least one
clock before the mode set operation. After the mode
register is set, a Standby or NOP command is required. Low signals of RAS, CAS, and WE at the
positive edge of the clock activate the mode set operation. Address input data at this timing defines pa-
V55C2128164V(T/B) Rev.1.2 August 2002
6
V55C2128164V(T/B)
MOSEL VITELIC
Address Input for Mode Set (Mode Register Operation)
BA1 BA0 A11 A10 A9
A8
Operation Mode
A7
A6
A5
A4
A3
A2
A1
A0
CAS Latency
BT
Burst Length
Address Bus (Ax)
Mode Register
Burst Type
Operation Mode
BA1 BA0 A11 A10 A9 A8 A7
Mode
A3
Type
0
Sequential
1
Interleave
0
0
0
0
0
0
0
Burst Read/Burst
Write
0
0
0
0
1
0
0
Burst Read/Single
Write
Burst Length
CAS Latency
A6
0
0
A5
0
0
A4
0
1
Length
Latency
A2
A0
Reserve
Sequential
Interleave
0
0
0
1
1
2
0
0
1
2
2
4
1
0
1
0
0
1
1
3
0
1
0
4
1
0
0
Reserve
0
1
1
8
8
1
0
1
Reserve
1
0
0
Reserve
Reserve
1
1
0
Reserve
1
0
1
Reserve
Reserve
1
1
1
Reserve
1
1
0
Reserve
Reserve
1
1
1
Full page
Reserve
with an operation change from a read to a write is
possible by exploiting DQM to avoid bus contention.
When two or more banks are activated
sequentially, interleaved bank read or write
operations are possible. With the programmed
burst length, alternate access and precharge
operations on two or more banks can realize fast
serial data access modes among many different
pages. Once two or more banks are activated,
column to column interleave operation can be done
between different pages.
Similar to the page mode of conventional
DRAM’s, burst read or write accesses on any column address are possible once the RAS cycle
latches the sense amplifiers. The maximum tRAS or
the refresh interval time limits the number of random
column accesses. A new burst access can be done
even before the previous burst ends. The interrupt
operation at every clock cycles is supported. When
the previous burst is interrupted, the remaining addresses are overridden by the new address with the
full burst length. An interrupt which accompanies
V55C2128164V(T/B) Rev. 1.2 August 2002
A1
7
V55C2128164V(T/B)
MOSEL VITELIC
Low Power Mode Register Table
BA1 BA0 A11 A10 A9
1*)
0*)
A8
A7
A6
A5
A4
all have to be set to "0"
A3
A2
TCR
A1
Address Bus (Ax)
A0
Mode Register
PASR
Self-Refresh:
Temperature-Compensated
A4
A3
Max case temp
0
0
70OC
0
1
45OC
1
0
15OC
1
1
85OC
Partial-Array Self Refresh:
A1
A0
banks to be self-refreshed
0
0
0
all banks
0
0
1
1/2 array (BA1=0)
0
1
0
1/4 array (BA1=0, BA0=0)
0
1
1
Reserved
1
0
0
Reserved
1
0
1
1/8 array (BA1=BA0=0, A11=0)
1
1
0
1/16 array (BA1=BA0=0,
A11=A10=0)
1
1
1
Reserved
A2
*)BA1 and BA0 must be 1, 0 to select the Extended Mode Register (Vs. the Mode Register)
The Low Power Mode Register must be set during the initialization sequence. Once the device is operational, the
Low Power Mode Register set can be issued anytime when the part is idle.
V55C2128164V(T/B) Rev. 1.2 August 2002
8
V55C2128164V(T/B)
MOSEL VITELIC
Burst Length and Sequence:
Burst Starting Address
Length
(A2 A1 A0)
2
xx0
xx1
4
x00
x01
x10
x11
8
000
001
010
011
100
101
110
111
Full Page
nnn
Sequential Burst Addressing
(decimal)
0, 1
1, 0
0,
1,
2,
3,
0
1
2
3
4
5
6
7
1
2
3
4
5
6
7
0
2
3
4
5
6
7
0
1
0, 1
1, 0
1,
2,
3,
0,
2,
3,
0,
1,
3
4
5
6
7
0
1
2
4
5
6
7
0
1
2
3
0,
1,
2,
3,
3
0
1
2
5
6
7
0
1
2
3
4
Cn, Cn+1, Cn+2
6
7
0
1
2
3
4
5
7
0
1
2
3
4
5
6
0
1
2
3
4
5
6
7
1
0
3
2
5
4
7
6
2
3
0
1
6
7
4
5
1,
0,
3,
2,
3
2
1
0
7
6
5
4
2,
3,
0,
1,
4
5
6
7
0
1
2
3
3
2
1
0
5
4
7
6
1
0
3
2
6
7
4
5
2
3
0
1
7
6
5
4
3
2
1
0
Not supported
a data mask function for writes. When DQM is
a data mask function for writes. When DQM is activated, the write operation at the next clock is prohibited (DQM Write Mask Latency tDQW = zero clocks).
Refresh Mode
SDRAM has two refresh modes, Auto Refresh
and Self Refresh. Auto Refresh is similar to the CAS
-before-RAS refresh of conventional DRAMs. All of
banks must be precharged before applying any refresh mode. An on-chip address counter increments
the word and the bank addresses and no bank information is required for both refresh modes.
The chip enters the Auto Refresh mode, when
RAS and CAS are held low and CKE and WE are
held high at a clock timing. The mode restores word
line after the refresh and no external precharge
command is necessary. A minimum tRC time is required between two automatic refreshes in a burst
refresh mode. The same rule applies to any access
command after the automatic refresh operation.
The chip has an on-chip timer and the Self Refresh mode is available. It enters the mode when
RAS, CAS, and CKE are low and WE is high at a
clock timing. All of external control signals including
the clock are disabled. Returning CKE to high enables the clock and initiates the refresh exit operation. After the exit command, at least one tRC delay
is required prior to any access command.
Power Down
In order to reduce standby power consumption, a
power down mode is available. All banks must be
precharged and the necessary Precharge delay
(trp) must occur before the SDRAM can enter the
Power Down mode. Once the Power Down mode is
initiated by holding CKE low, all of the receiver circuits except CLK and CKE are gated off. The Power
Down mode does not perform any refresh operations, therefore the device can’t remain in Power
Down mode longer than the Refresh period (tref) of
the device. Exit from this mode is performed by taking CKE “high”. One clock delay is required for
mode entry and exit.
Auto Precharge
Two methods are available to precharge
SDRAMs. In an automatic precharge mode, the
CAS timing accepts one extra address, CA10, to
determine whether the chip restores or not after the
operation. If CA10 is high when a Read Command
is issued, the Read with Auto-Precharge function
is initiated. The SDRAM automatically enters the
precharge operation one clock before the last data
out for CAS latencies 2, two clocks for CAS latencies 3 and three clocks for CAS latencies 4. If CA10
is high when a Write Command is issued, the Write
DQM Function
DQM has two functions for data I/O read and
write operations. During reads, when it turns to
“high” at a clock timing, data outputs are disabled
and become high impedance after two clock delay
(DQM Data Disable Latency tDQZ ). It also provides
V55C2128164V(T/B) Rev. 1.2 August 2002
Interleave Burst Addressing
(decimal)
9
V55C2128164V(T/B)
MOSEL VITELIC
with Auto-Precharge function is initiated. The
SDRAM automatically enters the precharge operation a time delay equal to tWR (Write recovery time)
after the last data in.
Burst Termination
Once a burst read or write operation has been initiated, there are several methods in which to terminate the burst operation prematurely. These
methods include using another Read or Write Command to interrupt an existing burst operation, use a
Precharge Command to interrupt a burst cycle and
close the active bank, or using the Burst Stop Command to terminate the existing burst operation but
leave the bank open for future Read or Write Commands to the same page of the active bank. When
interrupting a burst with another Read or Write
Command care must be taken to avoid I/O contention. The Burst Stop Command, however, has the
fewest restrictions making it the easiest method to
use when terminating a burst operation before it has
been completed. If a Burst Stop command is issued
during a burst write operation, then any residual
data from the burst write cycle will be ignored. Data
that is presented on the I/O pins before the Burst
Stop Command is registered will be written to the
memory.
Precharge Command
There is also a separate precharge command
available. When RAS and WE are low and CAS is
high at a clock timing, it triggers the precharge
operation. Three address bits, BA0, BA1 and A10
are used to define banks as shown in the following
list. The precharge command can be imposed one
clock before the last data out for CAS latency = 2,
two clocks before the last data out for CAS latency
= 3. Writes require a time delay twr from the last
data out to apply the precharge command.
Bank Selection by Address Bits:
A10
BA0 BA1
0
0
0
Bank 0
0
0
1
Bank 1
0
1
0
Bank 2
0
1
1
Bank 3
1
X
X
all Banks
Deep Power Down Mode
TheDeep Power Down mode is an unique functi
on with very low standby currents. All internal volat
ge generators inside the RAM are stopped and all
memory data is lost in this mode. To enter the Deep
Power Down mode all banks must be precharged.
Recommended Operation and Characteristics
TA = 0 to 70 °C(Commercial)/-25 to 85 °C(Extended); VSS = 0 V; VCC= 2.5 V,VCCQ = 1.8V
Limit Values
Parameter
Symbol
min.
max.
Unit
VCC
2.3
2.9
V
I/O Supply Voltage
VCCQ
1.65
2.9
V
1, 2
Input high voltage
VIH
0.8xVCCQ
Vcc+0.3
V
1, 2
Input low voltage
VIL
– 0.3
0.3
V
1, 2
Output high voltage (IOUT = – 4.0 mA)
VOH
VCCQ-0.2
–
V
Output low voltage (IOUT = 4.0 mA)
VOL
–
0.4
V
Input leakage current, any input
(0 V < VIN < 3.6 V, all other inputs = 0 V)
II(L)
–5
5
µA
Output leakage current
(DQ is disabled, 0 V < VOUT < VCC )
IO(L)
–5
5
µA
Supply voltage
Notes
Note:
1. All voltages are referenced to VSS.
2. VIH may overshoot to VCC + 0.8 V for pulse width of < 4ns with 2.5V. VIL may undershoot to -0.8 V for pulse width < 4.0 ns with
2.5V. Pulse width measured at 50% points with amplitude measured peak to DC reference.
V55C2128164V(T/B) Rev. 1.2 August 2002
10
V55C2128164V(T/B)
MOSEL VITELIC
Absolute Maximum Ratings*
Operating temperature range (commercial)0 to 70 °C
Operating temperature range (extended) -25 to 85 °C
Storage temperature range ............... -55 to 150 °C
Input/output voltage .................. -0.3 to (VCC+0.3) V
Power supply voltage .......................... -0.3 to 3.6 V
Power dissipation .......................................... 0.7 W
Data out current (short circuit) ...................... 50 mA
*Note:
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage of the device.
Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
Operating Currents TA = 0 to 70 °C(Commercial)/-25 to 85 °C(Extended);
VSS = 0 V; VCC= 2.5 V,VCCQ = 1.8V(Recommended Operating Conditions unless otherwise noted)
Max.
Symbol
Parameter & Test Condition
-6
-7 / -7PC
-8PC
10
Unit
Note
ICC1
Operating Current
tRC = tRCMIN., tRC = tCKMIN.
Active-precharge command cycling, without Burst Operation
1 bank operation
190
170
150
130
mA
7
Precharge Standby Current
in Power Down Mode
CS =VIH, CKE≤ VIL(max)
tCK = min.
1.5
1.5
1.5
1.5
mA
7
tCK = Infinity
1
1
1
1
mA
7
Precharge Standby Current
in Non-Power Down Mode
ICC2NS
CS =VIH, CKE≥ VIL(max)
tCK = min.
55
45
35
25
mA
tCK = Infinity
5
5
5
5
mA
CKE ≥ VIH(MIN.)
65
55
45
35
mA
CKE ≤ VIL(MAX.)
(Power down mode)
10
10
10
10
mA
ICC2P
ICC2PS
ICC2N
ICC3N
ICC3P
No Operating Current
tCK = min, CS = VIH(min)
bank ; active state ( 4 banks)
ICC4
Burst Operating Current
tCK = min
Read/Write command cycling
130
110
90
70
mA
7,8
ICC5
Auto Refresh Current
tCK = min
Auto Refresh command cycling
270
250
210
190
mA
7
ICC7
Deep Power down Current
10
10
10
10
uA
Notes:
7. These parameters depend on the cycle rate and these values are measured by the cycle rate under the minimum value of tCK and
tRC. Input signals are changed one time during tCK.
8. These parameter depend on output loading. Specified values are obtained with output open.
V55C2128164V(T/B) Rev. 1.2 August 2002
11
V55C2128164V(T/B)
MOSEL VITELIC
Temperature Compensated/Partial Array Self-Refresh Currents
Parameter & Test Condition
Self Refresh Current
Self refresh Mode
CKE=0.2V, tck=infinity,
full array activations, all banks
Self Refresh Current
Self refresh Mode
CKE=0.2V, tck=infinity,
1/2 array activations, Bank 0+1
Self Refresh Current
Self refresh Mode
CKE=0.2V, tck=infinity,
1/4 array activations, Bank 0
Self Refresh Current
Self refresh Mode
CKE=0.2V, tck=infinity,
1/8 array activations, Bank 0
Self Refresh Current
Self refresh Mode
CKE=0.2V, tck=infinity,
1/16 array activations, Bank 0
V55C2128164V(T/B) Rev. 1.2 August 2002
Symb.
Max.
Unit
ICC6
520
uA
70OC max
350
uA
45OC max
250
uA
15OC max
210
uA
380
uA
70OCmax
250
uA
45OC max
180
uA
15OCmax
160
uA
270
uA
70OC max
180
uA
45OC max
130
uA
15OC max
120
uA
190
uA
70OC max
140
uA
45OC max
100
uA
15OC max
90
uA
130
uA
70OC max
110
uA
45OC max
90
uA
15OC max
80
uA
Extended Mode
Register M[4:3]
Tcase[OC]
85OC max
85OC max
ICC6
85OC max
ICC6
85OC max
ICC6
85OC max
ICC6
12
V55C2128164V(T/B)
MOSEL VITELIC
AC Characteristics 1,2, 3
TA = 0 to 70 °C(Commercial)/-25 to 85 °C(Extended);VSS = 0 V; VCC= 2.5 V,VCCQ = 1.8V, tT=1 ns
Limit Values
-6
#
Symbol Parameter
-7PC
-8PC
-7
-10
Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Unit Note
Clock and Clock Enable
1
2
3
tCK
tCK
tAC
Clock Cycle Time
CAS Latency = 3
CAS Latency = 2
CAS Latency = 1
6
7.5
20
–
–
–
7
7.5
20
–
–
–
7
10
20
–
–
–
8
10
20
–
–
–
10
12
25
–
–
–
ns
ns
ns
Clock Frequency
CAS Latency = 3
CAS Latency = 2
CAS Latency = 1
–
–
–
166
133
50
–
–
–
143
133
50
–
–
–
143
100
50
–
–
–
125
100
50
–
–
–
100
83
40
MHz
MHz
MHz
Access Time from Clock
CAS Latency = 3
CAS Latency = 2
CAS Latency = 1
–
_
_
5.4
5.4
19
–
_
_
5.4
5.4
19
–
_
_
5.4
6
19
–
_
_
6
6
19
–
_
_
7
8
22
ns
ns
ns
2, 4
4
tCH
Clock High Pulse Width
2.5
–
2.5
–
2.5
–
3
–
3
–
ns
5
tCL
Clock Low Pulse Width
2.5
–
2.5
–
2.5
–
3
–
3
–
ns
6
tT
Transition Tim
0.3
1.2
0.3
1.2
0.3
1.2
0.5
10
0.5
10
ns
Setup and Hold Times
7
tIS
Input Setup Time
1.5
–
1.5
–
1.5
–
2
–
2.5
–
ns
5
8
tIH
Input Hold Time
0.8
–
0.8
–
0.8
–
1
–
1
–
ns
5
9
tCKS
Input Setup Time
1.5
–
1.5
–
1.5
–
2
–
2.5
–
ns
5
10
tCKH
CKE Hold Time
0.8
–
0.8
–
0.8
–
1
–
1
–
ns
5
11
tRSC
Mode Register Set-up Time
12
–
14
–
14
–
16
–
20
–
ns
12
tSB
Power Down Mode Entry Time
0
6
0
7
0
7
0
8
0
8
ns
Row to Column Delay Time
12
–
15
–
15
–
20
–
20
–
ns
6
–
15
–
15
–
20
–
20
–
ns
6
100K
45
100k
50
100k
ns
6
Common Parameters
13
tRCD
14
tRP
Row Precharge Time
15
15
tRAS
Row Active Time
40
16
tRC
Row Cycle Time
60
–
60
–
60
–
60
–
70
–
ns
6
17
tRRD
Activate(a) to Activate(b) Command
Period
12
–
14
–
14
–
16
–
20
–
ns
6
18
tCCD
CAS(a) to CAS(b) Command Period
1
–
1
–
1
–
1
–
1
–
CLK
100K 42 100K 42
Refresh Cycle
V55C2128164V(T/B) Rev. 1.2 August 2002
13
V55C2128164V(T/B)
MOSEL VITELIC
AC Characteristics (Cont’d)
Limit Values
-6
#
Symbol Parameter
19
tREF
20
tSREX
-7PC
-8PC
-7
-10
Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Unit Note
Refresh Period (4096 cycles)
—
64
—
64
—
64
—
64
—
64
ms
Self Refresh Exit Time
1
—
1
—
1
—
1
—
1
—
CLK
Read Cycle
21
tOH
Data Out Hold Time
3
–
3
–
3
–
3
–
3
–
ns
22
tLZ
Data Out to Low Impedance Time
1
–
1
–
1
–
1
–
1
–
ns
23
tHZ
Data Out to High Impedance Time
3
6
3
7
3
7
3
7
3
7
ns
24
tDQZ
DQM Data Out Disable Latency
–
2
–
2
–
2
–
2
–
2
CLK
Write Recovery Time
1
–
1
–
1
–
1
–
1
–
CLK
DQM Write Mask Latency
0
–
0
–
0
–
0
–
0
–
CLK
2
7
Write Cycle
25
tWR
26
tDQW
Notes for AC Parameters:
1. For proper power-up see the operation section of this data sheet.
2. AC timing tests are referenced to the 0.9V crossover point for VCCQ=1.8V components. The transition time is measured between VIH and V IL. All AC measurements assume tT = 1ns with the AC output load circuit shown in
Figure 1.
tCK
VIH
CLK
VIL
+ 1.4 V
tT
tCS
tCH
50 Ohm
1.4V
COMMAND
Z=50 Ohm
tLZ
I/O
tAC
tAC
50 pF
tOH
1.4V
OUTPUT
tHZ
Figure 1.
4. If clock rising time is longer than 1 ns, a time (tT/2 – 0.5) ns has to be added to this parameter.
5. If tT is longer than 1 ns, a time (tT – 1) ns has to be added to this parameter.
6. These parameter account for the number of clock cycle and depend on the operating frequency of the clock, as
follows:
the number of clock cycle = specified value of timing period (counted in fractions as a whole number)
Self Refresh Exit is a synchronous operation and begins on the 2nd positive clock edge after CKE returns high.
Self Refresh Exit is not complete until a time period equal to tRC is satisfied once the Self Refresh Exit command
is registered.
7. Referenced to the time which the output achieves the open circuit condition, not to output voltage levels
V55C2128164V(T/B) Rev. 1.2 August 2002
14
V55C2128164V(T/B)
MOSEL VITELIC
Timing Diagrams
1. Bank Activate Command Cycle
2. Burst Read Operation
3. Read Interrupted by a Read
4. Read to Write Interval
4.1 Read to Write Interval
4.2 Minimum Read to Write Interval
4.3 Non-Minimum Read to Write Interval
5. Burst Write Operation
6. Write and Read Interrupt
6.1 Write Interrupted by a Write
6.2 Write Interrupted by Read
7. Burst Write & Read with Auto-Precharge
7.1 Burst Write with Auto-Precharge
7.2 Burst Read with Auto-Precharge
8. Burst Termination
8.1 Termination of a Burst Write Operation
8.2 Termination of a Burst Write Operation
9. AC- Parameters
9.1 AC Parameters for a Write Timing
9.2 AC Parameters for a Read Timing
10. Mode Register Set
11. Power on Sequence and Auto Refresh (CBR)
12. Power Down Mode
13. Self Refresh (Entry and Exit)
14. Auto Refresh (CBR)
V55C2128164V(T/B) Rev. 1.2 August 2002
15
V55C2128164V(T/B)
MOSEL VITELIC
Timing Diagrams (Cont’d)
15. Random Column Read ( Page within same Bank)
15.1 CAS Latency = 2
15.2 CAS Latency = 3
16. Random Column Write ( Page within same Bank)
16.1 CAS Latency = 2
16.2 CAS Latency = 3
17. Random Row Read ( Interleaving Banks) with Precharge
17.1 CAS Latency = 2
17.2 CAS Latency = 3
18. Random Row Write ( Interleaving Banks) with Precharge
18.1 CAS Latency = 2
18.2 CAS Latency = 3
19. Precharge Termination of a Burst
19.1 CAS Latency = 2
19.2 CAS Latency = 3
V55C2128164V(T/B) Rev. 1.2 August 2002
16
V55C2128164V(T/B)
MOSEL VITELIC
1. Bank Activate Command Cycle
(CAS latency = 3)
T0
T1
T
T
T
T
T
CLK
..........
ADDRESS
Bank A
Col. Addr.
Bank A
Row Addr.
Bank A
Row Addr.
Bank B
Row Addr.
..........
tRCD
COMMAND
Bank A
Activate
tRRD
NOP
Write A
with Auto
Precharge
NOP
Bank B
Activate
..........
Bank A
Activate
NOP
: “H” or “L”
tRC
2. Burst Read Operation
(Burst Length = 4, CAS latency = 2, 3)
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
COMMAND
READ A
NOP
CAS latency = 2
tCK2, I/O’s
CAS latency = 3
tCK3, I/O’s
V55C2128164V(T/B) Rev. 1.2 August 2002
NOP
DOUT A0
NOP
NOP
DOUT A2
DOUT A1
DOUT A0
17
DOUT A1
NOP
NOP
DOUT A3
DOUT A2
DOUT A3
NOP
NOP
V55C2128164V(T/B)
MOSEL VITELIC
3. Read Interrupted by a Read
(Burst Length = 4, CAS latency = 2, 3)
T0
T1
READ A
READ B
T2
T3
T4
T5
T6
T7
T8
CLK
COMMAND
CAS latency = 2
NOP
DOUT A0
tCK2, I/O’s
CAS latency = 3
tCK3, I/O’s
NOP
NOP
NOP
NOP
DOUT B0
DOUT B1
DOUT B2
DOUT B3
DOUT A0
DOUT B0
DOUT B1
DOUT B2
T3
T4
T5
T6
NOP
NOP
DOUT B3
4.1 Read to Write Interval
(Burst Length = 4, CAS latency = 3)
T0
T1
T2
T7
T8
CLK
Minimum delay between the Read and Write Commands = 4+1 = 5 cycles
tDQW
DQM
tDQZ
COMMAND
NOP
READ A
I/O’s
NOP
NOP
NOP
WRITE B
DIN B0
DOUT A0
Must be Hi-Z before
the Write Command
: “H” or “L”
V55C2128164V(T/B) Rev. 1.2 August 2002
NOP
18
NOP
NOP
DIN B1
DIN B2
V55C2128164V(T/B)
MOSEL VITELIC
4.2 Minimum Read to Write Interval
(Burst Length = 4, CAS latency = 2)
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
tDQW
DQM
tDQZ
1 Clk Interval
COMMAND
NOP
NOP
BANK A
ACTIVATE
NOP
READ A
WRITE A
NOP
NOP
NOP
DIN A1
DIN A2
DIN A3
Must be Hi-Z before
the Write Command
CAS latency = 2
DIN A0
tCK2, I/O’s
: “H” or “L”
4.3 Non-Minimum Read to Write Interval
(Burst Length = 4, CAS latency = 2, 3)
T0
T1
T2
T3
T4
T5
T6
T7
T8
NOP
NOP
DIN B0
DIN B1
DIN B2
DIN B0
DIN B1
DIN B2
CLK
tDQW
DQM
tDQZ
COMMAND
NOP
READ A
NOP
NOP
READ A
NOP
WRITE B
CAS latency = 2
tCK1, I/O’s
DOUT A0
DOUT A1
Must be Hi-Z before
the Write Command
CAS latency = 3
tCK2, I/O’s
DOUT A0
: “H” or “L”
V55C2128164V(T/B) Rev. 1.2 August 2002
19
V55C2128164V(T/B)
MOSEL VITELIC
5. Burst Write Operation
(Burst Length = 4, CAS latency = 2, 3)
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
COMMAND
NOP
I/O’s
WRITE A
DIN A0
NOP
NOP
NOP
DIN A1
DIN A2
DIN A3
The first data element and the Write
are registered on the same clock edge.
NOP
NOP
NOP
NOP
don’t care
Extra data is ignored after
termination of a Burst.
6.1 Write Interrupted by a Write
(Burst Length = 4, CAS latency = 2, 3)
T0
T1
T2
WRITE A
WRITE B
T3
T4
T5
T6
T7
T8
CLK
COMMAND
NOP
NOP
NOP
NOP
DIN B1
DIN B2
DIN B3
1 Clk Interval
I/O’s
DIN A0
V55C2128164V(T/B) Rev. 1.2 August 2002
DIN B0
20
NOP
NOP
NOP
V55C2128164V(T/B)
MOSEL VITELIC
6.2 Write Interrupted by a Read
(Burst Length = 4, CAS latency = 2, 3)
T0
T1
T2
WRITE A
READ B
T3
T4
T5
T6
T7
T8
CLK
COMMAND
NOP
CAS latency = 2
tCK2, I/O’s
CAS latency = 3
tCK3, I/O’s
DIN A0
don’t care
DIN A0
don’t care
NOP
NOP
NOP
DOUT B0
don’t care
NOP
NOP
NOP
DOUT B1
DOUT B2
DOUT B3
DOUT B0
DOUT B1
DOUT B2
DOUT B3
Input data must be removed from the I/O’s at least one clock
cycle before the Read dataAPpears on the outputs to avoid
data contention.
7. Burst Write with Auto-Precharge
Burst Length = 2, CAS latency = 2, 3)
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
COMMAND
BANK A
ACTIVE
NOP
NOP
WRITE A
NOP
NOP
Auto-Precharge
I/O’s
DIN A0
DIN A1
tWR
NOP
tRP
tWR
CAS latency = 2
NOP
*
tRP
CAS latency = 3
I/O’s
DIN A0
DIN A1
*
Begin Autoprecharge
Bank can be reactivated after trp
V55C2128164V(T/B) Rev. 1.2 August 2002
21
NOP
V55C2128164V(T/B)
MOSEL VITELIC
7.2 Burst Read with Auto-Precharge
Burst Length = 4, CAS latency = 2, 3)
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
COMMAND
READ A
NOP
CAS latency = 2
tCK2, I/O’s
CAS latency = 3
tCK3, I/O’s
NOP
DOUT A0
NOP
NOP
*
DOUT A1
NOP
*
NOP
NOP
tRP
DOUT A2
DOUT A0
NOP
DOUT A1
DOUT A3
tRP
DOUT A2
DOUT A3
*
Begin Autoprecharge
Bank can be reactivated after tRP
V55C2128164V(T/B) Rev. 1.2 August 2002
22
V55C2128164V(T/B)
MOSEL VITELIC
8.1 Termination of a Burst Read Operation
(CAS latency = 2, 3)
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
COMMAND
READ A
NOP
CAS latency = 2
tCK2, I/O’s
NOP
NOP
Burst
Stop
DOUT A0
DOUT A1
DOUT A2
DOUT A3
DOUT A0
DOUT A1
DOUT A2
CAS latency = 3
tCK3, I/O’s
NOP
NOP
NOP
NOP
DOUT A3
8.2 Termination of a Burst Write Operation
(CAS latency = 2, 3)
T0
T1
T2
T3
T4
T5
T6
T7
T8
CLK
COMMAND
NOP
WRITE A
NOP
NOP
DIN A1
DIN A2
Burst
Stop
NOP
CAS latency = 2,3
I/O’s
DIN A0
don’t care
Input data for the Write is masked.
V55C2128164V(T/B) Rev. 1.2 August 2002
23
NOP
NOP
NOP
V55C2128164V(T/B) Rev. 1.2 August 2002
24
I/O
DQM
Addr
AP
BA
WE
CAS
RAS
CS
CKE
CLK
Hi-Z
tCH
tAS
tCKS
T0
T3
tCK2
tRCD
tAH
tCH
tCS
T2
Ax0
CAx
T4
Ax1
T5
Ax2
tRC
RBx
RBx
T6
Ax3
T7
Bx0
CBx
T9
T10
Bx1
Bx2
RAy
RAy
Bx3
tDS
Begin Auto Precharge
Bank A
T8
Activate
Write with
Activate
Write with
Activate
Command Auto Precharge Command Auto Precharge Command
Bank A
Command
Bank B
Command
Bank A
Bank A
Bank B
RAx
RAx
tCL
T1
9.1 AC Parameters for Write Timing
T13
T14
Ay1
tDH
Ay2
Ay3
Begin Auto Precharge
Bank B
T12
Write
Command
Bank A
Ay0
RAy
T11
T16
Precharge
Command
Bank A
tDPL
T15
tRP
T20
Activate
Command
Bank B
RBy
RBy
T19
tCKH
tRRD
T18
Activate
Command
Bank A
RAz
RAz
T17
T21
T22
Burst Length = 4, CAS Latency = 2
MOSEL VITELIC
V55C2128164V(T/B)
V55C2128164V(T/B) Rev. 1.2 August 2002
25
I/O
DQM
Addr
AP
BA
WE
CAS
RAS
CS
CKE
CLK
Hi-Z
tCL
tCKS
tCH
T0
tAS
RAx
RAx
tCS
tRCD
tAH
tCH
tCK2
T2
Activate
Command
Bank A
T1
9.2 AC Parameters for Read Timing
tRRD
CAx
T4
Read
Command
Bank A
T3
tLZ
tAC2
tAC2
Ax0
tOH
tRAS
RBx
RBx
T6
Activate
Command
Bank B
T5
RBx
T8
Read with
Auto Precharge
Command
Bank B
tHZ
Ax1
tRC
T7
T10
Precharge
Command
Bank A
Bx0
Begin Auto
Precharge
Bank B
T9
tHZ
Bx1
tRP
tCKH
RAy
RAy
T12
Activate
Command
Bank A
T11
T13
Burst Length = 2, CAS Latency = 2
MOSEL VITELIC
V55C2128164V(T/B)
\
V55C2128164V(T/B) Rev. 1.2 August 2002
26
Addr
AP
BA
WE
CAS
RAS
CS
CKE
CLK
T0
T2
Precharge
Command
All Banks
T1
10. Mode Register Set
T5
Mode Register
Set Command
T6
Any
Command
2 Clock min.
T4
Address Key
T3
T7
T8
T9
T10
T11
T12
T13
T14
T15
T16
T17
T18
T19
T20
T21
T22
MOSEL VITELIC
V55C2128164V(T/B)
\
V55C2128164V(T/B) Rev. 1.2 August 2002
27
I/O
DQM
Addr
AP
BA
WE
CAS
RAS
CS
CKE
CLK
T
T
TT
Precharge 1st Auto Refresh
Command
Command
All Banks
tRP
High level
is required
T
Inputs must be
stable for 200∝s
Hi-Z
T0
T
T
T
T1
T
T
T
2nd Auto Refresh
Command
Minimum of 2 Refresh Cycles are required
T
11. Power on Sequence and Auto Refresh (CBR)
tRC
T
T
TT
Mode Register
Set Command
T
T
T
Low Power Mode Register
Set Command
2 Clock min.
T
Address Key
T
MOSEL VITELIC
V55C2128164V(T/B)
\
V55C2128164V(T/B) Rev. 1.2 August 2002
28
Hi-Z
I/O
T1
Activate
Command
Bank A
RAx
Addr
DQM
RAx
AP
BA
WE
CAS
RAS
CS
CKE
CLK
T0
12. Power Down Mode
T2
T3
T4
T5
T6
T7
T8
T9
T10
T11
T12
T13
T15
Precharge
Command
Bank A
T14
T16
T18
Power Down
Mode Entry
T17
tCKSP
T19
T21
T22
Any
Command
Power Down
Mode Exit
T20
Burst Length = 4, CAS Latency = 2
MOSEL VITELIC
V55C2128164V(T/B)
\
V55C2128164V(T/B) Rev. 1.2 August 2002
29
I/O
DQM
Addr
AP
BA
WE
CAS
RAS
CS
CKE
CLK
All Banks
must be idle
Hi-Z
T0
T1
T3
Self Refresh
Entry
T2
T4
13. Self Refresh (Entry and Exit)
T5
T
T
T
tRC
T
Begin Self Refresh
Exit Command
t CKSR
tSREX
T
Self Refresh Exit
Command issued
T
T
Self Refresh
Exit
T
T
T
T
T
T
T
T
T
T
MOSEL VITELIC
V55C2128164V(T/B)
V55C2128164V(T/B) Rev. 1.2 August 2002
30
Hi-Z
Precharge
Command
All Banks
T4
T5
tRC
T6
T7
T9
Auto Refresh
Command
T8
T10
T12
tRC
T11
T13
T14
T15
I/O
DQM
Auto Refresh
Command
(Minimum Interval)
Activate
Command
Bank A
RAx
T3
Addr
T2
RAx
tRP
tCK2
T1
AP
BA
WE
CAS
RAS
CS
CKE
CLK
T0
14. Auto Refresh (CBR)
CAx
T17
Read
Command
Bank A
T16
T18
Ax0
T19
Ax1
T20
Ax2
T22
Ax3
T21
Burst Length = 4, CAS Latency = 2
MOSEL VITELIC
V55C2128164V(T/B)
\
V55C2128164V(T/B) Rev. 1.2 August 2002
31
I/O
Activate
Command
Bank A
RAw
Addr
Hi-Z
RAw
DQM
T1
tCK2
AP
BA
WE
CAS
RAS
CS
CKE
CLK
T0
CAw
T3
Read
Command
Bank A
T2
T4
Aw0
T5
Aw2
CAx
T7
Read
Command
Bank A
Aw1
T6
Ax0
CAy
T9
Read
Command
Bank A
Aw3
T8
Ax1
Ay2
T13
Precharge
Command
Bank A
T12
Ay1
T11
Ay0
T10
15.1 Random Column Read (Page within same Bank) (1 of 2)
Ay3
RAz
RAz
T15
Activate
Command
Bank A
T14
T17
Read
Command
Bank A
CAz
T16
T18
Az0
T19
Az1
T20
Az2
T21
Az3
T22
Burst Length = 4, CAS Latency = 2
MOSEL VITELIC
V55C2128164V(T/B)
\)
V55C2128164V(T/B) Rev. 1.2 August 2002
32
I/O
Activate
Command
Bank A
RAw
Addr
Hi-Z
RAw
DQM
T1
tCK3
AP
BA
WE
CAS
RAS
CS
CKE
CLK
T0
T2
CAw
T4
Read
Command
Bank A
T3
T5
T6
Aw1
CAx
T8
Read
Command
Bank A
Aw0
T7
Aw3
CAy
T12
Ax1
T11
Ax0
T10
Read
Command
Bank A
Aw2
T9
15.2 Random Column Read (Page within same Bank) (2 of 2)
Ay0
T13
Ay1
Ay2
T16
Ay3
T15
Precharge
Command
Bank A
T14
T18
Activate
Command
Bank A
RAz
RAz
T17
T19
T21
Read
Command
Bank A
CAz
T20
T22
Burst Length = 4, CAS Latency = 3
MOSEL VITELIC
V55C2128164V(T/B)
\)
V55C2128164V(T/B) Rev. 1.2 August 2002
33
I/O
Activate
Command
Bank B
RBz
Addr
Hi-Z
RBz
DQM
T1
tCK2
AP
BA
WE
CAS
RAS
CS
CKE
CLK
T0
CBz
T3
T4
T5
T6
CBx
T7
T8
CBy
T9
T10
T11
Write
Command
Bank B
Write
Command
Bank B
Write
Command
Bank B
T13
Precharge
Command
Bank B
T12
DBw0 DBw1 DBw2 DBw3 DBx0 DBx1 DBy0 DBy1 DBy2 DBy3
T2
16.1 Random Column Write (Page within same Bank) (1 of 2)
T15
Activate
Command
Bank B
RAw
RBz
RAw
RBz
T14
CAx
CBz
T17
T18
T19
T20
Write
Command
Bank B
DBz0 DBz1 DBz2 DBz3
T16
T21
T22
Burst Length = 4, CAS Latency = 2
MOSEL VITELIC
V55C2128164V(T/B)
\)
V55C2128164V(T/B) Rev. 1.2 August 2002
34
I/O
Activate
Command
Bank B
RBz
Addr
Hi-Z
RBz
DQM
T1
tCK3
AP
BA
WE
CAS
RAS
CS
CKE
CLK
T0
T2
CBz
T4
T5
T6
T7
CBx
T8
T9
CBy
T10
T11
T12
T13
Write
Command
Bank B
Write
Command
Bank B
Write
Command
Bank B
DBw0 DBw1 DBw2 DBw3 DBx0 DBx1 DBy0 DBy1 DBy2 DBy3
T3
16.2 Random Column Write (Page within same Bank) (2 of 2)
T15
Precharge
Command
Bank B
T14
T16
T18
Activate
Command
Bank B
RBz
RBz
T17
T19
T21
T22
Write
Command
Bank B
DBz0 DBz1
CBz
T20
Burst Length = 4, CAS Latency = 3
MOSEL VITELIC
V55C2128164V(T/B)
\)
V55C2128164V(T/B) Rev. 1.2 August 2002
35
I/O
tRCD
Activate
Command
Bank B
Hi-Z
RBx
A0 - A9
DQM
RBx
High
A10
A11(BS)
WE
CAS
RAS
CS
CKE
CLK
T0
tAC2
T2
Read
Command
Bank B
CBx
tCK2
T1
T3
Bx0
T4
Bx1
T5
Bx2
T6
Bx4
RAx
RAx
T8
Activate
Command
Bank A
Bx3
T7
17.1 Random Row Read (Interleaving Banks) (1 of 2)
Bx6
CAx
Ax1
RBy
RBy
T13
Activate
Command
Bank B
T12
Ax0
tRP
T11
Bx7
T10
Precharge
Command
Bank B
Read
Command
Bank A
Bx5
T9
Ax2
T14
Ax3
Ax5
T16
Ax4
T15
Ax6
T17
T19
Read
Command
Bank B
Ax7
CBy
T18
By0
T20
By1
T21
T22
Burst Length = 8, CAS Latency = 2
MOSEL VITELIC
V55C2128164V(T/B)
V55C2128164V(T/B) Rev. 1.2 August 2002
36
I/O
Activate
Command
Bank B
Hi-Z
RBx
A0 - A9
DQM
RBx
High
A10
A11(BS)
WE
CAS
RAS
CS
CKE
CLK
T0
tRCD
tCK3
T1
CBx
T3
Read
Command
Bank B
T2
tAC3
T4
T5
Bx0
T6
Bx2
RAx
RAx
T8
Activate
Command
Bank A
Bx1
T7
T9
Bx3
17. 2 Random Row Read (Interleaving Banks) (2 of 2)
Bx4
Bx7
tRP
RBy
RBy
Activate
Command
Bank B
Ax3
T16
Ax2
T15
Ax1
T14
Ax0
T13
Precharge
Command
Bank B
T12
Bx6
T11
Read
Command
Bank A
Bx5
CAx
T10
Ax4
T17
Ax6
T19
Read
Command
Bank B
Ax5
CBy
T18
By0
T21
Precharge
Command
Bank A
Ax7
T20
T22
Burst Length = 8, CAS Latency = 3
MOSEL VITELIC
V55C2128164V(T/B)
V55C2128164V(T/B) Rev. 1.2 August 2002
37
I/O
Activate
Command
Bank A
Hi-Z
RAx
A0 - A9
DQM
RAx
High
A10
A11(BS)
WE
CAS
RAS
CS
CKE
CLK
T0
T3
T4
T5
T6
T7
RBx
RBx
T8
CBx
tDPL
T9
T10
T12
tRP
T11
RAy
RAy
T13
T14
T15
T16
tDPL
CAy
T17
T18
T19
T20
T21
T22
Burst Length = 8, CAS Latency = 2
Activate
Command
Bank B
Precharge
Command
Bank A
Write
Command
Bank B
Activate
Command
Bank A
Precharge
Command
Bank B
Write
Command
Bank A
DAx0 DAx1 DAx2 DAx3 DAx4 DAx5 DAx6 DAx7 DBx0 DBx1 DBx2 DBx3 DBx4 DBx5 DBx6 DBx7 DAy0 DAy1 DAy2 DAy3 DAy4
T2
Write
Command
Bank A
tRCD
CAy
CAX
tCK2
T1
18.1 Random Row Write (Interleaving Banks) (1 of 2)
MOSEL VITELIC
V55C2128164V(T/B)
V55C2128164V(T/B) Rev. 1.2 August 2002
38
I/O
Activate
Command
Bank A
Hi-Z
RAx
A0 - A9
DQM
RAx
High
A10
A11(BS)
WE
CAS
RAS
CS
CKE
CLK
T0
tRCD
tCK3
T1
CAX
T3
T4
T5
T6
T7
RBx
RBx
T8
T9
T11
tDPL
CBx
T10
T12
T13
tRP
T14
T15
RAy
RAy
T16
T17
T19
tDPL
CAy
T18
T20
T21
T22
Burst Length = 8, CAS Latency = 3
Write
Command
Bank A
Activate
Command
Bank B
Write
Command
Bank B
Precharge
Command
Bank A
Activate
Command
Bank A
Write
Command
Bank A
Precharge
Command
Bank B
DAx0 DAx1 DAx2 DAx3 DAx4 DAx5 DAx6 DAx7 DBx0 DBx1 DBx2 DBx3 DBx4 DBx5 DBx6 DBx7 DAy0 DAy1 DAy2 DAy3
T2
18.2 Random Row Write (Interleaving Banks) (2 of 2)
MOSEL VITELIC
V55C2128164V(T/B)
V55C2128164V(T/B) Rev. 1.2 August 2002
39
I/O
Activate
Command
Bank A
Hi-Z
RAx
Addr
DQM
RAx
High
AP
BA
WE
CAS
RAS
CS
CKE
CLK
T0
T2
T3
T4
T5
T6
Write
Precharge
Command
Command
Bank A
Bank A
Precharge Termination
of a Write Burst. Write
data is masked.
DAx0 DAx1 DAx2 DAx3
CAx
tCK2
T1
tRP
19.1 Precharge Termination of a Burst (1 of 2)
RAy
RAy
T8
Activate
Command
Bank A
T7
CAy
T10
Read
Command
Bank A
T9
T11
Ay1
T13
Precharge
Command
Bank A
Ay0
T12
RAz
RAz
T15
Activate
Command
Bank A
Ay2
tRP
T14
T17
T18
Az1
T21
Az2
tRP
T20
Precharge
Command
Bank A
Az0
T19
Precharge Termination
of a Read Burst.
Read
Command
Bank A
CAz
T16
Burst Length = 8, CAS Latency = 2
T22
MOSEL VITELIC
V55C2128164V(T/B)
V55C2128164V(T/B) Rev. 1.2 August 2002
40
I/O
Activate
Command
Bank A
Hi-Z
RAx
Addr
DQM
RAx
High
AP
BA
WE
CAS
RAS
CS
CKE
CLK
T0
CAx
T3
Write
Command
Bank A
DAx0
T2
Write Data
is masked
tCK3
T1
T5
tRP
T6
RAy
RAy
T8
Activate
Command
Bank A
T7
Precharge Termination
of a Write Burst.
Precharge
Command
Bank A
T4
19.2 Precharge Termination of a Burst (2 of 2)
T9
T11
Read
Command
Bank A
CAy
T10
T12
T13
Ay1
T15
Precharge
Command
Bank A
Ay0
T14
Ay2
tRP
T16
T18
T19
T20
T21
Precharge Termination
of a Read Burst.
Activate
Command
Bank A
RAz
RAz
T17
T22
Burst Length = 4, 8, CAS Latency = 3
MOSEL VITELIC
V55C2128164V(T/B)
V55C2128164V(T/B)
MOSEL VITELIC
20.1 Deep Power Down Mode Entry
CLK
CKE
CS
WE
CAS
RAS
Addr.
DQM
DQ
input
DQ
output
High-Z
t RP
Precharge Command
Deep Power Down Entry
Deep Power Down Mode
Normal Mode
DP1.vsd
The deep power down mode has to be maintained for a minimum of 100µs.
V55C2128164V(T/B) Rev. 1.2 August 2002
41
V55C2128164V(T/B)
MOSEL VITELIC
20.2 Deep Power Down Exit
The deep power down mode is exited by asserting CKE high. After the exit, the following sequence is needed to
enter a new command:
1. Maintain NOP input conditions for a minimum of 200 µs
2. Issue precharge commands for all banks of the device
3. Issue eight or more autorefresh commands
4. Issue a mode register set command to initialize the mode register
5. Issue an extended mode register set command to initialize the extende mode register
CLK
CK E
CS
RAS
CAS
WE
200 s
Deep Power Do wn
exi t
V55C2128164V(T/B) Rev. 1.2 August 2002
tRP
All banks
prec harge
tRC
Auto
refresh
Au to
refresh
42
Mode
Register
Set
Exte nded
Mode
Regis ter
Set
New
Com mand
Acce pted
Here
V55C2128164V(T/B)
MOSEL VITELIC
FBGA-BOC package 54 BGA package with 3 depop. rows
V55C2128164V(T/B) Rev. 1.2 August 2002
43
V55C2128164V(T/B)
MOSEL VITELIC
WORLDWIDE OFFICES
U.S.A.
TAIWAN
SINGAPORE
UK & IRELAND
3910 NORTH FIRST STREET
SAN JOSE, CA 95134
PHONE: 408-433-6000
FAX: 408-433-0952
7F, NO. 102
MIN-CHUAN E. ROAD, SEC. 3
TAIPEI
PHONE: 886-2-2545-1213
FAX: 886-2-2545-1209
10 ANSON ROAD #23-13
INTERNATIONAL PLAZA
SINGAPORE 079903
PHONE: 65-6323-1801
FAX: 65-6323-7013
NO 19 LI HSIN ROAD
SCIENCE BASED IND. PARK
HSIN CHU, TAIWAN, R.O.C.
PHONE: 886-3-579-5888
FAX: 886-3-566-5888
JAPAN
SUITE 50, GROVEWOOD
BUSINESS CENTRE
STRATHCLYDE BUSINESS
PARK
BELLSHILL, LANARKSHIRE,
SCOTLAND, ML4 3NQ
PHONE: 44-1698-748515
FAX: 44-1698-748516
ONZE 1852 BUILDING 6F
2-14-6 SHINTOMI, CHUO-KU
TOKYO 104-0041
PHONE: 03-3537-1400
FAX: 03-3537-1402
U.S. SALES OFFICES
WEST
CENTRAL / EAST
3910 NORTH FIRST STREET
SAN JOSE, CA 95134
PHONE: 408-433-6000
FAX: 408-433-0952
604 FIELDWOOD CIRCLE
RICHARDSON, TX 75081
PHONE: 214-352-3775
FAX: 214-904-9029
© Copyright , MOSEL VITELIC Corp.
Printed in U.S.A.
MOSEL VITELIC subjects its products to normal quality control
sampling techniques which are intended to provide an assurance
of high quality products suitable for usual commercial applications. MOSEL VITELIC does not do testing appropriate to provide
100% product quality assurance and does not assume any liability for consequential or incidental arising from any use of its products. If such products are to be used in applications in which
personal injury might occur from failure, purchaser must do its
own quality assurance testing appropriate to such applications.
The information in this document is subject to change without
notice.
MOSEL VITELIC makes no commitment to update or keep current the information contained in this document. No part of this
document may be copied or reproduced in any form or by any
means without the prior written consent of MOSEL-VITELIC.
V55C2128164V(T/B) Rev. 1.2 August 2002
44