DATA SHEET NEC's WIDE BAND UPD5710TK SINGLE CONTROL CMOS SPDT SWITCH FEATURES DESCRIPTION • SUPPLY VOLTAGE : 1.8 to 3.3 V (2.8 V TYP.) • SINGLE SWITCH CONTROL VOLTAGE: Vcont (H) = 1.8 to 3.3 V (2.8 V TYP.) Vcont (L) = −0.2 to +0.2 V (0 V TYP.) NEC's UPD5710TK is a wide-band single control CMOS MMIC SPDT (Single Pole Double Throw) switch for mobile communications, instrumentation, short range wireless, and general-purpose RF switching applications. • LOW INSERTION LOSS: 0.6 dB TYP. @ DC to 1.0 GHz 0.8 dB TYP. @ 1.0 to 2.0 GHz 0.95 dB TYP. @ 2.0 to 2.5 GHz This device can operate from DC to 2.5GHz with low insertion loss and high isolation, and generally does not require blocking capacitors on the RF lines. The UPD5710TK is housed in a Pb-Free 6-pin minimold (1511) package, suitable for high-density surface mounting. • HIGH ISOLATION: 32.5 dB TYP. @ DC to 1.0 GHz 25 dB TYP. @ 1.0 to 2.0 GHz 22.5 dB TYP. @ 2.0 to 2.5 GHz APPLICATIONS • POWER HANDLING: Pin (0.1 dB) = +17.0 dBm TYP. @ 1.0GHz, VDD = 2.8 V Pin (1 dB) = +21.0 dBm TYP. @ 1.0 GHz, VDD = 2.8 V • • • • • HIGH-DENSITY SURFACE MOUNT PACKAGE: 6-pin minimold package (1.5 × 1.1 × 0.55 mm) MOBILE COMMUNICATIONS SET TOP BOXES SHORT RANGE WIRELESS INSTRUMENTATION • Pb-FREE ORDERING INFORMATION PART NUMBER PACKAGE MARKING μPD5710TK-E2-A 6-pinlead-less minimold (1511) C3L SUPPLYING FORM • Embossed tape 8 mm wide • Pin 1, 6 face the perforation side of the tape • Qty 5 kpcs/reel Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: UPD5710TK California Eastern Laboratories UPD5710TK PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM PIN NO. PIN NAME 1 OUTPUT1 2 GND 3 OUTPUT2 4 Vcont 5 INPUT 6 VDD TRUTH TABLE VCONT INPUT−OUTPUT1 INPUT−OUTPUT2 Low OFF ON High ON OFF ABSOLUTE MAXIMUM RATINGS (TA =+25ºC, unless otherwise specified) PARAMETER SYMBOL RATINGS UNIT Supply Voltage VDD +4.6 V Switch Control Voltage Vcont +4.6 V Continuous Current Idc 60 mA Input Power Pin +27 dBm Operating Ambient Temperature TA −45 to +85 °C Storage Temperature Tstg −65 to +150 °C RECOMMENDED OPERATING RANGE (TA =+25ºC, unless otherwise specified) PARAMETER SYMBOL MIN. TYP. MAX. UNIT VDD +1.8 +2.8 +3.3 V Switch Control Voltage (H) Vcont (H) +1.8 +2.8 +3.3 V Switch Control Voltage (L) Vcont (L) −0.2 0 +0.2 V Supply Voltage Notes 1. | Vcont(H) − Vcont(L) | ≤ 0.1 V UPD5710TK ELECTRICAL CHARACTERISTICS (TA = +25°C, VDD = 2.8V, Vcont(H) = 2.8 V , Vcont(L) = 0 V, unless otherwise specified) PARAMETER Insertion Loss 1 SYMBOL Lins1 MIN. TYP. MAX. UNIT f = DC to 1.0 GHz TEST CONDITIONS − 0.6 0.8 dB Insertion Loss 2 Lins2 f = 1.0 to 2.0 GHz − 0.8 1.0 dB Insertion Loss 3 Lins3 f = 2.0 to 2.5 GHz − 0.95 1.2 dB Isolation 1 ISL1 f = DC to 1.0 GHz 30 32.5 − dB Isolation 2 ISL2 f = 1.0 to 2.0 GHz 22 25 − dB Isolation 3 ISL3 f = 2.0 to 2.5 GHz - 22.5 − dB Input Return Loss RLin f = DC to 2.5 GHz 15 20 − dB RLout f = DC to 2.5 GHz 15 20 − dB 0.1 dB Loss Compression Input Power Note Pin (0.1 dB) f = 1.0 GHz +13.5 +17.0 − dBm 1 dB Loss Compression Input Power Note Pin (1 dB) f = 1.0 GHz − +21.0 − dBm Output Return Loss Intermodulation Intercept Point IIP3 2 tone, 1.000/1.001GHz, 1 MHz spacing − +33 − dBm Supply Current IDD No RF − 0.01 1.0 μA Switch Control Current Icont No RF - 0.01 1.0 μA Switch Control Speed tSW − 30 500 ns Notes . Pin (0.1 dB) or Pin (1 dB) are the measured input power level when the insertion loss increases 0.1 dB more or 1dB than that of linear range. UPD5710TK EVALUATION CIRCUIT The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. UPD5710TK ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD USING THE NEC EVALUATION BOARD SYMBOL VALUES C1, C2 1,000 pF UPD5710TK TYPICAL CHARACTERISTIC (TA = +25°C, VDD = 2.8 V, Vcont (H) = 2.8 V, Vcont (L) = 0 V, unless otherwise specified) Remark The graphs indicate nominal characteristics. UPD5710TK TYPICAL CHARACTERISTIC (TA = +25°C, VDD = 2.8 V, Vcont (H) = 2.8 V, Vcont (L) = 0 V, unless otherwise specified) Remark The graphs indicate nominal characteristics. UPD5710TK PACKAGE DIMENSIONS 6-PIN LEAD-LESS MINIMOLD (1511) (UNIT:mm) UPD5710TK RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Soldering Conditions Condition Symbol Infrared Reflow Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220°C or higher Preheating time at 120 to 180°C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) : 260°C or below : 10 seconds or less : 60 seconds or less : 120±30 seconds : 3 times : 0.2%(Wt.) or below IR260 VPS Peak temperature (package surface temperature) Time at temperature of 200°C or higher Preheating time at 120 to 150°C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) : 215°C or below : 25 to 40 seconds : 30 to 60 seconds : 3 times : 0.2%(Wt.) or below VP215 Wave Soldering Peak temperature (molten solder temperature) Time at peak temperature Preheating temperature (package surface temperature) Maximum number of flow processes Maximum chlorine content of rosin flux (% mass) : 260°C or below : 10 seconds or less : 120°C or below : 1 time : 0.2%(Wt.) or below WS260 Partial Heating Peak temperature (pin temperature) Soldering time (per side of device) Maximum chlorine content of rosin flux (% mass) : 350°C or below : 3 seconds or less : 0.2%(Wt.) or below HS350 Caution Do not use different soldering methods together (except for partial heating). 07/29/2004 A Business Partner of NEC Compound Semiconductor Devices, Ltd.