CEL UPG2415TK

GaAs INTEGRATED CIRCUIT
PG2415TK
0.5 to 6.0 GHz SPDT SWITCH
DESCRIPTION
The PG2415TK is a GaAs MMIC SPDT (Single Pole Double Throw) switch for 0.5 to 6.0 GHz applications,
including dual-band wireless LAN.
This device operates with dual control switching voltages of 2.7 to 5.3 V. This device can operate at frequencies
from 0.5 to 6.0 GHz, with low insertion loss and high isolation.
This device is housed in a 6-pin lead-less minimold package (1511 PKG) and is suitable for high-density surface
mounting.
FEATURES
• Switch control voltage
: Vcont (H) = 3.0 V TYP.
: Vcont (L) = 0 V TYP.
• Low insertion loss
: Lins = 0.45 dB TYP. @ f = 2.5 GHz
: Lins = 0.65 dB TYP. @ f = 6.0 GHz
• High isolation
: ISL = 28 dB TYP. @ f = 2.5 GHz
: ISL = 26 dB TYP. @ f = 6.0 GHz
• Handling power
: Pin (0.1 dB) = +31.0 dBm TYP. @ f = 2.0 to 6.0 GHz
• High-density surface mounting : 6-pin lead-less minimold package (1.5  1.1  0.55 mm)
APPLICATIONS
• Dual-band wireless LAN etc.
ORDERING INFORMATION
Part Number
PG2415TK-E2
Order Number
PG2415TK-E2-A
Package
6-pin lead-less minimold
(1511 PKG) (Pb-Free)
Marking
G6D
Supplying Form
 Embossed tape 8 mm wide
 Pin 1, 6 face the perforation side of the tape
 Qty 5 kpcs/reel
Remark To order evaluation samples, please contact your nearby sales office.
Part number for sample order: PG2415TK-A
Caution Although this device is designed to be as robust as possible, ESD (Electrostatic
Discharge) can damage this device. This device must be protected at all times from ESD. Static
charges may easily produce potentials of several kilovolts on the human body or equipment, which
can discharge without detection. Industry-standard ESD precautions must be employed at all times.
Document No. PG10793EJ01V0DS (1st edition)
Date Published February 2010 NS
PG2415TK
PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM
Pin No.
Pin Name
1
RF1
2
GND
3
RF2
4
Vcont2
5
RFC
6
Vcont1
SW TRUTH TABLE
ON Path
Vcont1
Vcont2
RFC-RF1
High
Low
RFC-RF2
Low
High
ABSOLUTE MAXIMUM RATINGS (T A = +25C, unless otherwise specified)
Parameter
Symbol
Switch Control Voltage
Ratings
+6.0
Vcont
Unit
Note
V
Input Power (Vcont (H) = 3.0 V)
Pin
+34.0
dBm
Input Power (Vcont (H) = 5.0 V)
Pin
+35.0
dBm
Power Dissipation (average)
PD
0.15
W
Operating Ambient Temperature
TA
45 to +85
C
Storage Temperature
Tstg
55 to +150
C
Note Vcont1  Vcont2  6.0 V
RECOMMENDED OPERATING RANGE (T A = +25C, unless otherwise specified)
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
f
0.5

6.0
GHz
Switch Control Voltage (H)
Vcont (H)
2.7
3.0
5.3
V
Switch Control Voltage (L)
Vcont (L)
0.2
0
0.2
V
Control Voltage Difference
Vcont (H),
Vcont (L)Note
0.1
0
0.1
V
Operating Frequency
Note Vcont (H) = Vcont1 (H)  Vcont2 (H)
Vcont (L) = Vcont1 (L)  Vcont2 (L)
2
Data Sheet PG10793EJ01V0DS
PG2415TK
ELECTRICAL CHARACTERISTICS
(T A = +25C, Vcont (H) = 3.0 V, Vcont (L) = 0 V, ZO = 50 , DC blocking capacitors = 8 pF, unless
otherwise specified)
Parameter
Symbol
Test Conditions
Note 1
MIN.
TYP.
MAX.
Unit

0.40
0.65
dB
Insertion Loss 1
Lins1
f = 0.5 to 2.0 GHz
Insertion Loss 2
Lins2
f = 2.0 to 2.5 GHz

0.45
0.70
dB
Insertion Loss 3
Lins3
f = 2.5 to 3.8 GHz

0.55
0.80
dB
Insertion Loss 4
Lins4
f = 3.8 to 6.0 GHz

0.65
0.90
dB
25
28

dB
Note 1
Isolation 1
ISL1
f = 0.5 to 2.0 GHz
Isolation 2
ISL2
f = 2.0 to 2.5 GHz
25
28

dB
Isolation 3
ISL3
f = 2.5 to 3.8 GHz
25
28

dB
Isolation 4
ISL4
f = 3.8 to 6.0 GHz
22
26

dB
15
20

dB
15
20

dB
10
15

dB

+32.0

dBm

+31.0

dBm

+35.0

dBm

+34.0

dBm
f = 2.0 to 6.0 GHz

+34.0

dBm
Return Loss 1
RL1
f = 0.5 to 2.0 GHz
Return Loss 2
RL2
f = 2.0 to 2.5 GHz
Return Loss 3
RL3
f = 2.5 to 6.0 GHz
0.1 dB Loss Compression
Input Power
1 dB Loss Compression
Input Power
Pin (0.1 dB)
Note 2
f = 0.5 to 2.0 GHz
Note 1
Note 1
f = 2.0 to 6.0 GHz
Pin (1 dB)
Note 3
f = 0.5 to 6.0 GHz
Note 1
f = 0.5 to 2.0 GHz
Note 1
, Vcont (H) = 5.0 V
Input 3rd Order Intercept Point
IIP3
f = 2.5 GHz, Pin = +20 dBm

+60

dBm
2nd Harmonics
2f0
f = 2.5 GHz, Pin = +20 dBm

80

dBc
3rd Harmonics
3f0
f = 2.5 GHz, Pin = +20 dBm

80

dBc
Switch Control Current
Icont
No RF input

0.1
10
A
Switch Control Speed
tSW
50% CTL to 90/10% RF

50
250
ns
Notes 1. DC blocking capacitors = 56 pF at f = 0.5 to 2.0 GHz
2. Pin (0.1 dB) is the measured input power level when the insertion loss increases 0.1 dB more than that of
the linear range.
3. Pin (1 dB) is the measured input power level when the insertion loss increases 1 dB more than that of the
linear range.
Caution It is necessary to use DC blocking capacitors with this device.
The value of DC blocking capacitors should be chosen to accommodate the frequency of
operation, bandwidth, switching speed and the condition with actual board of your system.
Data Sheet PG10793EJ01V0DS
3
PG2415TK
EVALUATION CIRCUIT
Note C1 : 0.5 to 2.0 GHz
56 pF
: 2.0 to 6.0 GHz
8 pF
C2 : 1 000 pF
The application circuits and their parameters are for reference only and are not intended for use in actual design-ins
APPLICATION INFORMATION
• LESD provides a means to increase the ESD protection on a specific RF port, typically the port attached to the
antenna.
• The value may be tailored to provide specific electrical responses.
• The RF ground connections should be kept as short as possible and connected to directly to a good RF ground
for best performance.
4
Data Sheet PG10793EJ01V0DS
PG2415TK
ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD
USING THE EVALUATION BOARD
Symbol
C1
C2
Test Conditions
Values
f = 0.5 to 2.0 GHz
56 pF
f = 2.0 to 6.0 GHz
8 pF
1 000 pF
Data Sheet PG10793EJ01V0DS
5
PG2415TK
TYPICAL CHARACTERISTICS (T A = +25C, Vcont (H) = 3.0 V, Vcont (L) = 0 V, ZO = 50 , DC blocking
capacitors = 8 pF, unless otherwise specified)
Remark The graphs indicate nominal characteristics.
6
Data Sheet PG10793EJ01V0DS
PG2415TK
Remark The graphs indicate nominal characteristics.
Data Sheet PG10793EJ01V0DS
7
PG2415TK
MOUNTING PAD LAYOUT DIMENSIONS
6-PIN LEAD-LESS MINIMOLD (1511 PKG) (UNIT: mm)
Remark The mounting pad layout in this document is for reference only.
8
Data Sheet PG10793EJ01V0DS
PG2415TK
PACKAGE DIMENSIONS
6-PIN LEAD-LESS MINIMOLD (1511 PKG) (UNIT: mm)
Data Sheet PG10793EJ01V0DS
9
PG2415TK
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered and mounted under the following recommended conditions.
For soldering
methods and conditions other than those recommended below, contact your nearby sales office.
Soldering Method
Infrared Reflow
Wave Soldering
Partial Heating
Soldering Conditions
Condition Symbol
Peak temperature (package surface temperature)
: 260C or below
Time at peak temperature
: 10 seconds or less
Time at temperature of 220C or higher
: 60 seconds or less
Preheating time at 120 to 180C
: 12030 seconds
Maximum number of reflow processes
: 3 times
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
Peak temperature (molten solder temperature)
: 260C or below
Time at peak temperature
: 10 seconds or less
Preheating temperature (package surface temperature)
: 120C or below
Maximum number of flow processes
: 1 time
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
Peak temperature (terminal temperature)
: 350C or below
Soldering time (per side of device)
: 3 seconds or less
Maximum chlorine content of rosin flux (% mass)
: 0.2%(Wt.) or below
Caution Do not use different soldering methods together (except for partial heating).
10
Data Sheet PG10793EJ01V0DS
IR260
WS260
HS350
PG2415TK
Caution GaAs Products
This product uses gallium arsenide (GaAs).
GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the
following points.
• Follow related laws and ordinances when disposing of the product. If there are no applicable laws
and/or ordinances, dispose of the product as recommended below.
1. Commission a disposal company able to (with a license to) collect, transport and dispose of
materials that contain arsenic and other such industrial waste materials.
2. Exclude the product from general industrial waste and household garbage, and ensure that the
product is controlled (as industrial waste subject to special control) up until final disposal.
• Do not burn, destroy, cut, crush, or chemically dissolve the product.
• Do not lick the product or in any way allow it to enter the mouth.
Data Sheet PG10793EJ01V0DS
11