NEC's 1.5W UPG2179TB L, S-BAND SPDT SWITCH FEATURES DESCRIPTION • SWITCH CONTROL VOLTAGE: NEC's UPG2179TB is a GaAs MMIC L, S-band SPDT (Single Vcont (H) = 2.5 to 5.3 V (3.0 V TYP.) Pole Double Throw) switch for mobile phone and Vcont (L) = −0.2 to +0.2 V (0 V TYP.) L, S-band applications from 0.5 to 3.0 GHz. • LOW INSERTION LOSS: 0.25 dB TYP. @ 0.5 to 1.0 GHz, Vcont = 3.0 V/0 V 0.30 dB TYP. @ 1.0 to 2.0 GHz, Vcont = 3.0 V/0 V 0.35 dB TYP. @ 2.0 to 2.5 GHz, Vcont = 3.0 V/0 V 0.40 dB TYP. @ 2.0 to 3.0 GHz, Vcont = 3.0 V/0 V This device can operate with 2.5 to 5.3 V from 50 MHz to 3 GHz with low insertion loss and high isolation. The UPG2179TB is housed in a Pb-Free 6-pin super minimold package suitable for high-density surface mounting. • HIGH ISOLATION: 27 dB TYP. @ 0.5 to 2.0 GHz, Vcont = 3.0 V/0 V 24 dB TYP. @ 2.0 to 2.5 GHz, Vcont = 3.0 V/0 V APPLICATIONS • HIGH POWER: Pin (0.1 dB) = +29.0 dBm TYP. @ 0.5 to 3.0 GHz, Vcont = 3.0 V/0 V Pin (1 dB) = +32.0 dBm TYP. @ 0.5 to 3.0 GHz, Vcont = 3.0 V/0 V • L, S-band digital cellular and cordless telephones • PCS, W-LAN, WLL and BluetoothTM • Short Range Wireless • HIGH-DENSITY SURFACE MOUNT PACKAGE: 6-pin super minimold package (2.0 × 1.25 × 0.9 mm) • PB-FREE ORDERING INFORMATION PART NUMBER PACKAGE MARKING UPG2179TB-E4-A 6-pin super minimold G4C SUPPLYING FORM • Embossed tape 8 mm wide • Pin 4, 5, 6 face the perforation side of the tape • Qty 3 kpcs/reel Remark To order evaluation samples, contact your nearby sales ofÞce. Part number for sample order: UPG2179TB-A Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge. California Eastern Laboratories UPG2179TB PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM (Top View) G4C 1 (Top View) 2 3 (Bottom View) 6 1 6 6 1 5 2 5 5 2 4 3 4 4 3 Pin No. Pin Name 1 OUTPUT1 2 GND 3 OUTPUT2 4 Vcont2 5 INPUT 6 Vcont1 TRUTH TABLE VCONT1 VCONT2 INPUT−OUTPUT1 INPU−OUTPUT2 Low High High ON OFF Low OFF ON ABSOLUTE MAXIMUM RATINGS (TA = 25°C, unless otherwise speciÞed) PARAMETER Switch Control Voltage SYMBOL RATINGS UNIT Vcont 6.0 V Input Power Pin +33 dBm Operating Ambient Temperature TA −45 to +85 °C Storage Temperature Tstg −55 to +150 °C Note |Vcont1 – Vcont2| ≤ 6.0 V RECOMMENDED OPERATING RANGE (TA = 25°C, unless otherwise speciÞed) PARAMETER SYMBOL MIN. TYP. MAX. UNIT Switch Control Voltage (H) Vcont (H) 2.5 3.0 5.3 V Switch Control Voltage (L) Vcont (L) −0.2 0 0.2 V UPG2179TB ELECTRICAL CHARACTERISTICS (TA = +25°C, Vcont = 3.0 V/0V, DC blocking capacitors = 100 pF, unless otherwise speciÞed) PARAMETER Insertion Loss 1 SYMBOL TEST CONDITIONS LINS1 f = 0.5 to 1.0 GHz Note1 MIN. TYP. MAX. UNIT − 0.25 0.45 dB Insertion Loss 2 LINS2 f = 1.0 to 2.0 GHz − 0.30 0.50 dB Insertion Loss 3 LINS3 f = 2.0 to 2.5 GHz − 0.35 0.55 dB Insertion Loss 4 LINS4 f = 2.5 to 3.0 GHz − 0.40 0.60 dB 23 27 − dB 20 24 − dB 15 20 − dB 15 20 − dB f = 2.0 GHz +25.5 +29.0 − dBm f = 2.5 GHz +25.5 +29.0 − dBm Isolation 1 ISL1 f = 0.5 to 2.0 GHz Isolation 2 ISL2 f = 2.0 to 3.0 GHz Note1 Input Return Loss RLin f = 0.5 to 3.0 GHz Note1 Output Return Loss RLout f = 0.5 to 3.0 GHz Note1 0.1 dB Loss Compression Input Pin (0.1 dB) Power Note2 f = 0.5 to 3.0 GHz − +29.0 − dBm Switch Control Current Icont No signal − 4 20 μA Switch Control Speed tSW 50%CTL to 90/10%RF − 50 500 ns Note 1. DC blocking capacitor = 1 000pF at f = 0.05 to 0.5 GHz. 2. Pin(0.1 dB) is the measured input power level when the insertion loss increases 0.1 dB more than that of linear range. STANDARD CHARACTERISTICS FOR REFERENCE (TA = +25°C, Vcont = 3.0 V/0 V, DC blocking capacitors = 100 pF, unless otherwise speciÞed) PARAMETER 1 dB Loss Compression Input SYMBOL Pin (1 dB) TEST CONDITIONS MIN. TYP. MAX. UNIT f = 0.5 to 3.0 GHz − +32.0 − dBm f = 0.5 to 3.0 GHz, 2 tone, 5 MHz spacing − +60.0 − dBm Power Note 3rd Order Intermodulation Intercept Point IIP3 Note Pin (1 dB) is the measured input power level when the insertion loss increases 1 dB more than that of linear range. Caution It is necessary to use DC blocking capacitors with this device. The value of DC blocking capacitors should be chosen to accommodate the frequency of operation, bandwidth, switching speed and the condition with the actual board of your system. The range of recommended DC blocking capacitor value is less than 100 pF for frequencies above 0.5 GHz, and 1,000 pF for frequencies below 0.5 GHz. UPG2179TB EVALUATION CIRCUIT (Vcont1 = 3.0 V, Vcont2 = 0 V or Vcont2 = 0 V, Vcont1 = 3.0 V, off chip DC blocking capacitors value C1 = 51 pF, C2 = 1 000 pF (Bypass), using NEC standard evaluation board) OUTPUT2 OUTPUT1 56 pF 56 pF 1 000 pF 3 2 1 4 5 6 56 pF 1 000 pF Vcont2 INPUT Vcont1 This application circuits and their parameters are for reference only and are not intended for use in actual design-ins. UPG2179TB ILLUSTRATION OF TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD Vcont2 6pin SMM SPDT SW Vc2 OUTPUT2 C2 C 2 C 4 OUT 2 INPUT G4C C1 C3 C1 C1 IN C C 1 5 C2 OUT 1 OUTPUT1 Vc1 Vcont1 USING THE NEC EVALUATION BOARD SYMBOL C1, C2, C3 C4, C5 VALUES 100 pF 1 000 pF UPG2179TB TYPICAL CHARACTERISTICS (TA = +25°C, Vcont = 3.0 V/0 V, DC blocking capacitors = 100 pF, unless otherwise speciÞed) INPUT-OUTPUT2 INSERTION LOSS vs. FREQUENCY 0.5 0.4 0.4 0.3 0.3 Insertion Loss LINS (dB) 0.5 0.2 0.1 0 -0.1 -0.2 -0.3 0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 -0.4 -0.5 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 -0.5 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 Frequency f (GHz) Frequency f (GHz) INPUT-OUTPUT1 ISOLATION vs. FREQUENCY INPUT-OUTPUT2 ISOLATION vs. FREQUENCY 50 40 40 30 30 Isolation ISL (dB) 50 20 10 0 -10 -20 20 10 0 -10 -20 -30 -30 -40 -40 -50 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 -50 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 Frequency f (GHz) Frequency f (GHz) INPUT-OUTPUT1 INPUT RETURN LOSS vs. FREQUENCY INPUT-OUTPUT2 INPUT RETURN LOSS vs. FREQUENCY 50 50 40 40 Input Return Loss RLin (dB) Input Return Loss RLin (dB) Isolation ISL (dB) Insertion Loss LINS (dB) INPUT-OUTPUT1 INSERTION LOSS vs. FREQUENCY 30 20 10 0 -10 -20 -30 30 20 10 0 -10 -20 -30 -40 -40 -50 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 -50 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 Frequency f (GHz) Remark The graphs indicate nominal characteristics. Frequency f (GHz) INPUT-OUTPUT1 OUTPUT RETURN LOSS vs. FREQUENCY INPUT-OUTPUT2 OUTPUT RETURN LOSS vs. FREQUENCY 50 50 40 40 Output Return Loss RLout (dB) Output Return Loss RLout (dB) UPG2179TB 30 20 10 0 -10 -20 -30 -40 -50 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 10 0 -10 -20 -30 -40 Frequency f (GHz) Frequency f (GHz) OUTPUT POWER vs. INPUT POWER OUTPUT POWER vs. INPUT POWER 33 f = 1.0 GHz 31 29 Output Power Pout (dBm) Output Power Pout (dBm) 20 -50 0.5 0.8 1.1 1.4 1.7 2.0 2.3 2.6 2.9 3.2 3.5 33 31 30 27 25 23 21 19 17 15 13 15 17 f = 2.5 GHz 29 27 25 23 21 19 17 15 19 21 23 25 27 29 31 33 35 Input Power Pin (dBm) Remark The graphs indicate nominal characteristics. 13 15 14 19 21 23 25 27 29 31 Input Power Pin (dBm) 33 35 UPG2179TB PACKAGE DIMENSIONS 6-PIN SUPER MINIMOLD (UNIT: mm) 2.1±0.1 0.2+0.1 -0.05 0.65 0.65 1.3 0.15+0.1 -0.05 0 to 0.1 0.7 0.1 MIN. 0.9±0.1 2.0±0.2 1.25±0.1 UPG2179TB RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact your nearby sales ofÞce. Soldering Method Soldering Conditions Condition Symbol Infrared Reßow Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220°C or higher Preheating time at 120 to 180°C Maximum number of reßow processes Maximum chlorine content of rosin ßux (% mass) : 260°C or below : 10 seconds or less : 60 seconds or less : 120±30 seconds : 3 times : 0.2%(Wt.) or below IR260 VPS Peak temperature (package surface temperature) Time at temperature of 200°C or higher Preheating time at 120 to 150°C Maximum number of reßow processes Maximum chlorine content of rosin ßux (% mass) : 215°C or below : 25 to 40 seconds : 30 to 60 seconds : 3 times : 0.2%(Wt.) or below VP215 Wave Soldering Peak temperature (molten solder temperature) Time at peak temperature : 260°C or below : 10 seconds or less WS260 Preheating temperature (package surface temperature) : 120°C or below Maximum number of ßow processes : 1 time Maximum chlorine content of rosin ßux (% mass) : 0.2%(Wt.) or below Partial Heating Caution Peak temperature (pin temperature) Soldering time (per side of device) Maximum chlorine content of rosin ßux (% mass) : 350°C or below : 3 seconds or less : 0.2%(Wt.) or below HS350 Do not use different soldering methods together (except for partial heating). Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. 06/01/2004 A Business Partner of NEC Compound Semiconductor Devices, Ltd. 5-148