POWER-ONE MAP140

MAP140 SERIES
Power-One’s MAP140 series provides a full range of options and up
to 30 watts more power than comparable products in this industry
standard footprint. With a universal input from 85 to 264 VAC and
power densities up to 2.6 watts/inch3, the MAP140 meets the most
rigorous requirements of commercial, industrial, and datacom systems.
Rated for use in convection and forced air cooled (200 LFM)
applications, the MAP140 delivers dependable power with a Mean
Time Before Failure (MTBF) in excess of 180,000 hours. In addition
to UL, CSA, and TÜV regulatory compliance, the MAP140 displays
the CE Mark.
FEATURES
• Universal Input 85-264 VAC
• Input Transient & ESD Compliance to EN61000-4-2/-3/-4
• CE Marked to Low Voltage Directive
• Industry Standard Footprint: 7.00" x 4.30" x 1.80"
(177.8mm x 109.2mm x 45.7mm)
• Remote Sense and Overvoltage Protection
• Power Fail Signal Standard on MAP140-3000P, Optional
on MAP140-1012 and MAP140-1024
• Optional Overtemperature Protection, L-Bracket, and Cover.
SINGLE OUTPUT MODEL SELECTION CHART
MODEL
MAP140-1012
MAP140-1024
MAP140-1048
OUTPUT
VOLTAGE
ADJUSTMENT
RANGE
CONVECTION
COOLED CURRENT
FORCED AIR
CURRENT (NOTE 3)
LINE
REGULATION
LOAD
REGULATION
RIPPLE & NOISE
%p-p (NOTE 1)
INITIAL SETTING
ACCURACY
12V/15V
24V/28V
48V
11.0V to 16.0V
22.8V to 29.2V
45.6V to 54.0V
9.2/7.3A (Note 2)
4.6/4A (Note 2)
2.3A
12.5A/10A (Note 2)
6.3A/5.4A (Note 2)
3.1A
0.1%
0.1%
0.1%
0.5%
0.5%
0.5%
1%
1%
1%
11.97V to 12.03V
23.95V to 24.05V
47.9V to 48.1V
NOTES: 1) Maximum peak to peak noise expressed as a percentage of output voltage, 20MHz bandwidth.
2) MAP140-1012 output currents are expressed as 12V/15V operation. MAP140-1024 output currents are expressed as 24V/28V operation.
3) With 200 LFM forced air cooling.
MULTIPLE OUTPUT MODEL SELECTION CHART – 80W CONVECTION COOLED, 140W FORCED AIR COOLED (200 LFM)
MODEL
MAP140-3000P
OUTPUT
VOLTAGE
ADJUSTMENT
RANGE
OUTPUT
CURRENT (NOTE 1)
PEAK OUTPUT
CURRENT (NOTE 1)
LINE
REGULATION
LOAD
REGULATION
RIPPLE & NOISE
%p-p (NOTE 2)
INITIAL SETTING
ACCURACY
+5V
+12V
-12V
4.75 - 5.25V
Fixed
Fixed
16A/25A
4A/9A PK
1A/1.5A PK
20A/25A PK
4A/9A PK
1A/1.5A PK
0.2%
0.1%
0.1%
1%
2%
2%
1%
1%
1%
5.09V to 5.11V
11.97V to 12.03V
-11.4V to -12.6V
NOTES: 1) Peak loads up to 140 Watts for 60 seconds or less are acceptable, (10% duty cycle max.). Peak power must not exceed 140 watts.
2) Maximum peak to peak noise expressed as a percentage of output voltage, 20MHz bandwidth.
INPUT SPECIFICATIONS
PARAMETER
CONDITIONS/DESCRIPTION
MIN
Input Voltage - AC
Input Frequency
Brown Out Protection
Hold-up Time
85
47
85
20
16
Input Protection
Inrush Surge Current
Continuous input range.
AC input.
Lowest AC input voltage that regulation is maintained with full rated loads.
Nominal AC input voltage (110 VAC)
110 watt load:
140 watt load:
85 VAC (140W load).
110 VAC (140W load).
Non-user serviceable internally located AC input line fuse.
Internally limited by thermistor. Vin = 264VAC (one cycle). 25°C.
Operating Frequency
Switching frequency of main transformer.
Input Current
NOM
MAX
UNITS
264
63
VAC
Hz
VAC
mS
2.5
2.0
41
22
ARMS
APK
kHz
NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments,
or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are
subject to change without notice.
Rev. 04/2000
1
MAP140 SERIES
OUTPUT SPECIFICATIONS
PARAMETER
CONDITIONS/DESCRIPTION
Efficiency
Minimum Loads
Full load, 110 VAC. Varies with distribution of loads among outputs.
65
Single output models.
0
MAP140-3000P, total output current of V1 + V2 (Note 1).
2
Full load, 20MHz bandwidth.
Single output models.
MAP140-3000P with convection cooling.
MAP140-3000P with 200 LFM forced air cooling.
Output voltage overshoot/undershoot at turn-on/turn-off.
Varies by output. Total regulation includes: line changes from 90-132 VAC or 175-264,
changes in load starting at 20% load and changing to 100% load.
Recovery time, to within 1% of initial set point due to a 50-100%
load change, 4% max. deviation.
Time required for initial output voltage stabilization.
MAP140-3000P
Single output models
Time required for output voltage to rise from 10% to 90%.
Ripple and Noise
Output Power
Overshoot / Undershoot
Regulation
Transient Response
Turn-on Delay
Turn-on Rise Time
MIN
NOM
MAX
UNITS
70
80
%
Amps
See Model Selection Chart.
See Model Selection Chart.
80
Watts
140
0
V
See Model Selection Chart.
500
µS
1
2
20
Sec
mS
NOTES: 1) Minimum load is required only to meet the regulation limits of V3.
INTERFACE SIGNALS AND INTERNAL PROTECTION
PARAMETER
CONDITIONS/DESCRIPTION
Overvoltage Protection
Provided on single output models
and V1 of MAP140-3000P.
Overload Protection
Remote Sense
Input Power Fail
Warning
Overtemperature Protection
MIN
NOM
MAX
MAP140-3000P, V1
6.1
7.2
MAP140-1012
17.3
20.2
MAP140-1024
32.2
37.8
MAP140-1048
55.2
64.8
Fully protected against output overload and short circuit. Automatic recovery upon removal of overload condition.
Voltage drop compensated for at the load.
250
TTL compatible logic signal. Time before regulation dropout due
to loss of input power at 140 watts, 110 VAC. Standard on MAP140-3000P
2.3
and optional on MAP140-1012.
Optional signal provides system shutdown due to excessive internal temperature. See options.
UNITS
V
mV
mS
SAFETY, REGULATORY, AND EMI SPECIFICATIONS
PARAMETER
CONDITIONS/DESCRIPTION
Agency Approvals
Dielectric Withstand Voltage
Electromagnetic
Interference, Conducted
ESD Susceptibility
Radiated Susceptibility
EFT/Burst
Input Transient Protection
UL1950.
CSA 22.2 No. 234/950.
EN60950 (TÜV).
Input to output, 1 second.
FCC CFR title 47 part 15 sub-part B - conducted & radiated.
EN55022 / CISPR 22 conducted.
Per EN61000-4-2, level 4.
Per EN61000-4-3, level 3.
Per EN61000-4-4, level 3.
Per EN61000-4-5, class 3.
MIN
Insulation Resistance
Leakage Current
Input to Output.
Per EN60950, 264VAC.
NOM
MAX
UNITS
Approved
Line to Line
Line to Ground
2600
B
B
8
10
±2
1
2
10
VDC
Class
kV
V/M
kV
kV
MΩ
110 VAC
264 VAC
0.5
1.5
mA
ENVIRONMENTAL SPECIFICATIONS
PARAMETER
CONDITIONS/DESCRIPTION
Altitude
Operating Temperature
Operating.
Non-operating.
Derate linearly above 50°C by 2.5% per °C
Storage Temperature
Temperature Coefficient
Relative Humidity
Shock
Vibration
0°C to 70°C (after 15 minute warm-up period).
Non-condensing.
Operating, peak acceleration.
Random vibration, 10Hz to 2kHz, 3 axis.
MIN
At 100% load:
At 50% load:
NOM
0
0
-40
±0.02
2
MAX
UNITS
10k
40k
50
70
85
±0.05
95
20
6
ASL Ft.
ASL Ft.
°C
°C
°C
%/°C
%RH
GPK
GRMS
MAP140 SERIES
OPTIONS
DESCRIPTION
NOTES
L-Bracket
Add ‘L’ suffix to model number.
Cover
Add ‘C’ suffix to model number. Includes L-Bracket.
For convection cooled applications, derate output power to 75 watts, maximum.
Add ‘P’ suffix to model number. Provides 2.3mS warning time before main output
drops 5%. Warning time increases at reduced load levels. Option available only
on MAP140-1012 and MAP140-1024. Power fail is standard on MAP140-3000P.
Add ‘T’ suffix to model number. Initiates shut-down in the event of an overtemperature
condition. Automatic recovery. Where available, Power Fail signal is initiated prior to shutdown.
Power Fail Signal
Thermal Shutdown
DIMENSIONS
7.19" x 4.50" x 2.40"
(182.6mm x 114.3mm x 61.0mm)
7.19" x 4.50" x 2.40"
(182.6mm x 114.3mm x 61.0mm)
OVERALL SIZE: 7.00" X 4.30" X 1.97" (177.8mm x 109.2mm x 50.0mm)
OVERALL WEIGHT: 1.3 LBS (0.59 kg)
Contact factory for dimensions for L-bracket and cover.
3
N/A
N/A