TI TPS62081

TPS62080, TPS62080A
TPS62081, TPS62082
www.ti.com
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
1.2A High Efficient Step Down Converter with Snooze Mode
Check for Samples: TPS62080, TPS62080A, TPS62081, TPS62082
FEATURES
DESCRIPTION
1
•
•
•
•
•
•
•
•
•
•
•
The TPS6208x devices are a family of high frequency
synchronous step down converters. With an input
voltage range of 2.3V to 6.0V, common battery
technologies are supported. Alternatively, the device
can be used for low voltage system power rails.
TM
DCS-Control Architecture for Fast Transient
Regulation
Snooze Mode for 6.5µA Ultra Low Quiescent
Current
2.3V to 6.0V Input Voltage Range
Supports High Output Capacitance up to
100µF
100% Duty Cycle for Lowest Dropout
Power Save Mode for Light Load Efficiency
Output Discharge Function
Short Circuit Protection
Power Good Output
Thermal Shutdown
Available in 2x2mm 8-Pin SON Package and
VSSOP Package
The TPS6208x focuses on high efficient step down
conversion over a wide output current range. At
medium to heavy loads, the converter operates in
PWM mode and automatically enters Power Save
Mode operation at light load currents to maintain high
efficiency over the entire load current range. To
maintain high efficiency at very low load or no load
currents, a Snooze Mode with an ultra low quiescent
current is implemented, that is enabled by the Mode
pin. This function increases the run-time of battery
driven applications and keeps the standby current at
its lowest level to meet green energy standards
targeting for a low stand-by current.
To address the requirements of system power rails,
the internal compensation circuit allows a large
selection of external output capacitor values ranging
from 10µF up to 100uF effective capacitance. With its
DCS-ControlTM architecture excellent load transient
performance and output voltage regulation accuracy
is achieved. The device is available in 2x2mm SON
package and VSSOP package with Thermal PAD.
APPLICATIONS
•
•
•
Battery Powered Portable Devices
Point of Load Regulators
System Power Rail Voltage Conversion
TPS62081
VIN
2.3V .. 6V
POWER GOOD
VIN
PG
EN
SW
180k
1µH
10µF
MODE
GND
VOS
1.8V
VOUT
22µF
FB
Figure 1. Typical Application of TPS62081 (1.8V Fixed Output)
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
UNLESS OTHERWISE NOTED this document contains
PRODUCTION DATA information current as of publication date.
Products conform to specifications per the terms of Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011–2012, Texas Instruments Incorporated
TPS62080, TPS62080A
TPS62081, TPS62082
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
www.ti.com
Table 1. ORDERING INFORMATION
TA
OUTPUT VOLTAGE (1)
PACKAGE MARKING
PACKAGE
PART NUMBER (2)
Adjustable
QVR
8-Pin SON
TPS62080DSG
1.8 V
QVS
8-Pin SON
TPS62081DSG
3.3 V
QVT
8-Pin SON
TPS62082DSG
Adjustable
SBN
8-Pin SON
TPS62080ADSG
8-Pin VSSOP
TPS62080ADGN (3)
–40°C to 85°C
Adjustable
(1)
(2)
(3)
Contact the factory to check availability of other fixed output voltage versions.
For detailed ordering information please check the PACKAGE OPTION ADDENDUM section at the end of this datasheet.
Product Preview
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted) (1)
Voltage range at VIN, PG, VOS (2)
Voltage range at SW (2) (3)
Voltage range at FB
(2)
Voltage range at EN, MODE (2)
VALUE
UNIT
–0.3 to 7
V
–1 to 7
V
–0.3 to 3.6
V
–0.3 to (VIN + 0.3V)
V
2
kV
500
V
ESD rating, Human Body Model
ESD rating, Charged Device Model
Continuous total power dissipation
See Dissipation Rating Table
Operating junction temperature range, TJ
–40 to 150
°C
Operating ambient temperature range, TA
–40 to 85
°C
Storage temperature range, Tstg
–65 to 150
°C
(1)
(2)
(3)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute–maximum–rated conditions for extended periods may affect device reliability.
All voltage values are with respect to network ground terminal.
During operation, device switching
THERMAL INFORMATION
TPS62080
THERMAL METRIC (1)
DSG (8 PINS)
θJA
Junction-to-ambient thermal resistance
65.1
θJCtop
Junction-to-case (top) thermal resistance
100.7
θJB
Junction-to-board thermal resistance
135.7
ψJT
Junction-to-top characterization parameter
2.3
ψJB
Junction-to-board characterization parameter
45.1
θJCbot
Junction-to-case (bottom) thermal resistance
8.6
(1)
UNITS
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
RECOMMENDED OPERATING CONDITIONS (1)
MIN
TYP
MAX
VIN
Input voltage range, VIN
2.3
6.0
VOUT
Output voltage range
0.5
4.0
ISNOOZE Maximum load current in Snooze Mode
UNIT
V
V
2
mA
TA
Operating ambient temperature
–40
85
°C
TJ
Operating junction temperature
–40
125
°C
(1)
2
Refer to the APPLICATION INFORMATION section for further information.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
TPS62080, TPS62080A
TPS62081, TPS62082
www.ti.com
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
ELECTRICAL CHARACTERISTICS
Over recommended free-air temperature range, TA = -40°C to 85°C, typical values are at TA = 25°C (unless otherwise noted),
VIN=3.6V, MODE = LOW.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY
VIN
Input voltage range
2.3
6.0
V
Quiescent current into VIN
IOUT = 0mA, Device not switching
30
uA
IQ
Quiescent current into VIN (SNOOZE
MODE)
IOUT = 0mA, Device not switching, MODE=HIGH
6.5
uA
ISD
Shutdown current into VIN
EN = LOW
Under voltage lock out
Input voltage falling
1.8
Under voltage lock out hysteresis
Rising above VUVLO
120
mV
Thermal shut down
Temperature rising
150
°C
Thermal shutdown hysteresis
Temperature falling below TJSD
20
°C
VUVLO
TJSD
1
2.0
µA
V
LOGIC INTERFACE (ENABLE, MODE)
VIH
High level input voltage
2.3V ≤ VIN ≤ 6.0V
VIL
Low level input voltage
2.3V ≤ VIN ≤ 6.0V
ILKG
Input leakage current
1
V
0.4
V
0.01
0.5
µA
–10
–5
%
POWER GOOD
VPG
Power good threshold
VOUT falling referenced to VOUT nominal
–15
Power good hysteresis
5
VIL
Low level voltage
Isink = 500 µA
IPG,LKG
PG Leakage current
VPG = 5.0 V
%
0.3
V
0.1
µA
0.5
4.0
V
0.01
OUTPUT
Output voltage range
TPS62080, TPS62080A
Output voltage accuracy
TPS62081
IOUT = 0 mA; VIN ≥ 2.3V
–2.5
2.5
%
Output voltage accuracy
TPS62082
IOUT = 0 mA; VIN ≥ 3.6V
–2.5
2.5
%
Snooze Mode output voltage accuracy
MODE = HIGH; VIN ≥ 2.3V and VIN ≥ VOUT + 1V
–5
5
%
VFB
Feedback regulation voltage
TPS62080, TPS62080A
VIN ≥ 2.3V and VIN ≥ VOUT + 1V
0.45
0.462
V
IFB
Feedback input bias current
TPS62080, TPS62080A
VFB = 0.45 V
10
100
nA
RDIS
Output discharge resistor
VOUT
0.438
EN = LOW, VOUT = 1.8 V
1
TPS62080A , EN = LOW, VOUT = 1.2 V,
25
Line Regulation
RDS(on)
ILIM
Load Regulation
TPS62081, TPS62082
High side FET on-resistance
ISW = 500 mA
Low side FET on-resistance
ISW = 500 mA
High side FET switch current limit
Rising inductor current
Copyright © 2011–2012, Texas Instruments Incorporated
40
kΩ
65
%/V
-0.25
%/A
120
mΩ
90
1.6
2.8
mΩ
4
Submit Documentation Feedback
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
Ω
0
A
3
TPS62080, TPS62080A
TPS62081, TPS62082
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
www.ti.com
DEVICE INFORMATION
2
MODE
3
FB
4
MA
GND
ER
1
TH
EN
LP
AD
QFN
8 PIN 2X2 mm
8
VIN
7
SW
6
PG
5
VOS
PIN FUNCTIONS
PIN
NAME
NO.
I/O
DESCRIPTION
VIN
8
PWR
EN
1
IN
Device Enable Logic Input.
Logic HIGH enables the device, logic LOW disables the device and turns it into shutdown.
MODE
3
IN
Snooze Mode Enable Logic Input.
Logic HIGH enables the Snooze Mode, logic LOW disables the Snooze Mode
GND
2
PWR
VOS
5
IN
SW
7
PWR
FB
4
IN
PG
6
OUT
Thermal Pad
4
Power Supply Voltage Input.
Power and Signal Ground.
Output Voltage Sense Pin for the internal control loop. Must be connected to output.
Switch Pin connected to the internal MOSFET switches and inductor terminal.
Connect the inductor of the output filter here.
Feedback Pin for the internal control loop.
Connect this pin to the external feedback divider for the adjustable output version. For the fixed output voltage
versions this pin must be left floating or connected to GND.
Power Good open drain output.
This pin is pulled to low if the output voltage is below regulation limits. Can be left floating if not used.
Connect it to GND.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
TPS62080, TPS62080A
TPS62081, TPS62082
www.ti.com
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
FUNCTIONAL BLOCK DIAGRAMS
MODE
PG
Control
Logic
Thermal
Shutdown
VIN
High Side
N-MOS
Power
Good
Gate
Driver
Low Side
N-MOS
SW
Active
Output
Discharge
Snooze Mode
GND
EN
ramp
Softstart
comparator
direct control
&
compensation
Under
Voltage
Shutdown
VOS
FB
error
amplifier
minimum
on-timer
DSC-CONTROL
REF
TM
Figure 2. Functional Block Diagram (Adjustable Output Voltage Version)
MODE
PG
Control
Logic
Thermal
Shutdown
VIN
High Side
N-MOS
Power
Good
Gate
Driver
Low Side
N-MOS
SW
Active
Output
Discharge
Snooze Mode
GND
EN
ramp
Softstart
comparator
Under
Voltage
Shutdown
VOS
error
amplifier
minimum
on-timer
DSC-CONTROL
direct control
&
compensation
TM
FB
REF
Figure 3. Functional Block Diagram (Fixed Output Voltage Version)
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
5
TPS62080, TPS62080A
TPS62081, TPS62082
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
www.ti.com
TYPICAL CHARACTERISTICS
PARAMETER MEASUREMENT INFORMATION
TPS6208x
VIN
POWER GOOD
VIN
PG
EN
SW
R3
L1
C3
C1
MODE
VOUT
C2
VOS
R1
GND
FB
R2
Table 2. List of Components
REFERENCE
DESCRIPTION
MANUFACTURER
C1
10uF, Ceramic Capacitor, 6.3V, X5R, size 0603
Std
C2
22uF, Ceramic Capacitor, 6.3V, X5R, size 0805,
GRM21BR60J226ME39L
Murata
C3
47uF, Tantalum Capacitor, 8V, 35mΩ, size 3528,
T520B476M008ATE035
Kemet
L1
1.0µH, Power Inductor, 2.2A, size 3x3x1.2mm, XFL3012-102MEB
R1
Depending on the output voltage of TPS62080, 1%; Not be
populated for TPS62081, TPS62082;
R2
39.2k, Chip Resistor, 1/16W, 1%, size 0603
Std
R3
178k, Chip Resistor, 1/16W, 1%, size 0603
Std
Coilcraft
TABLE OF GRAPHS
Figure
Efficiency
Output Voltage
Accuracy
Quiescent Current
RDS(on)
Switching Frequency
Typical Operation
6
TPS62080, Load Current, VOUT = 0.9V
Figure 4
TPS62080, Load Current, VOUT = 1.2V
Figure 5
TPS62080, Load Current, VOUT = 2.5V
Figure 6
TPS62081, Load Current, VOUT = 1.8V
Figure 7
TPS62082, Load Current, VOUT = 3.3V
Figure 8
TPS62080, Input Voltage, VOUT = 0.9V
Figure 9
TPS62080, Input Voltage, VOUT = 2.5V
Figure 10
TPS62081, Input Voltage, VOUT = 1.8V
Figure 11
TPS62082, Input Voltage, VOUT = 3.3V
Figure 12
TPS62080, Load Current, VOUT = 0.9V
Figure 13
TPS62080, Load Current, VOUT = 2.5V
Figure 14
TPS62081, Load Current, VOUT = 1.8V
Figure 15
TPS62082, Load Current, VOUT = 3.3V
Figure 16
Input Voltage, Normal Mode
Figure 17
Input Voltage, Snooze Mode
Figure 18
Input Voltage, High Side FET
Figure 19
Input Voltage, Low Side FET
Figure 20
TPS62080, Load Current, VOUT = 0.9V,
Figure 21
TPS62080, Load Current, VOUT = 2.5V,
Figure 22
TPS62080, VIN = 3.3V, VOUT = 1.2V, Load Current = 500mA, PWM Mode
Figure 23
TPS62080, VIN = 3.3V, VOUT = 1.2V, Load Current = 10mA, PFM Mode
Figure 24
TPS62080, VIN = 3.3V, VOUT = 1.2V, Load Current = 2mA, Snooze Mode
Figure 25
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
TPS62080, TPS62080A
TPS62081, TPS62082
www.ti.com
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
Figure
Load Transient
TPS62080, VIN = 3.3V, VOUT = 1.2V, Load Current = 50mA to 1A
Figure 26
Line Transient
TPS62080, VIN = 3.3V to 4.2V, VOUT = 1.2V, Load = 2.2Ω
Figure 27
TPS62080, VIN = 3.3V, VOUT = 1.2V, Load = 2.2Ω
Figure 28
TPS62080, VIN = 3.3V, VOUT = 1.2V, No Load
Figure 29
TPS62080, VIN = 3.3V, VOUT = 1.2V, No Load
Figure 30
Startup
Shutdown with
Output Discharge
EFFICIENCY
vs
LOAD CURRENT
EFFICIENCY
vs
LOAD CURRENT
100
90
80
80
70
70
Efficiency (%)
Efficiency (%)
90
100
TPS62080
VOUT = 0.9 V
60
50
VIN = 2.8 V
VIN = 3.6 V
VIN = 4.2 V
VIN = 2.8 V, Snooze Mode
VIN = 3.6 V, Snooze Mode
VIN = 4.2 V, Snooze Mode
40
30
20
10
0
10u
100u
1m
10m
100m
Output Current (A)
1
50
10
0
10u
3
100u
G001
1m
10m
100m
Output Current (A)
Figure 4.
Figure 5.
EFFICIENCY
vs
LOAD CURRENT
EFFICIENCY
vs
LOAD CURRENT
1
3
G002
100
TPS62080
VOUT = 2.5 V
90
80
80
70
70
60
50
VIN = 3.6 V
VIN = 4.2 V
VIN = 5.0 V
VIN = 3.6 V, Snooze Mode
VIN = 4.2 V, Snooze Mode
VIN = 5.0 V, Snooze Mode
40
30
20
10
0
10u
VIN = 2.8 V
VIN = 3.6 V
VIN = 4.2 V
VIN = 2.8 V, Snooze Mode
VIN = 3.6 V, Snooze Mode
VIN = 4.2 V, Snooze Mode
40
20
Efficiency (%)
Efficiency (%)
60
30
100
90
TPS62080
VOUT = 1.2 V
100u
1m
10m
100m
Output Current (A)
Figure 6.
Copyright © 2011–2012, Texas Instruments Incorporated
1
TPS62081
VOUT = 1.8 V
60
50
VIN = 2.8 V
VIN = 3.6 V
VIN = 4.2 V
VIN = 2.8 V, Snooze Mode
VIN = 3.6 V, Snooze Mode
VIN = 4.2 V, Snooze Mode
40
30
20
10
3
G003
0
10u
100u
1m
10m
100m
Output Current (A)
1
3
G005
Figure 7.
Submit Documentation Feedback
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
7
TPS62080, TPS62080A
TPS62081, TPS62082
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
www.ti.com
EFFICIENCY
vs
LOAD CURRENT
OUTPUT VOLTAGE
vs
INPUT VOLTAGE
0.910
100
90
0.905
Output Voltage (V)
Efficiency (%)
80
70
TPS62082
VOUT = 3.3 V
60
50
VIN = 3.6 V
VIN = 4.2 V
VIN = 5.0 V
VIN = 3.6 V, Snooze Mode
VIN = 4.2 V, Snooze Mode
VIN = 5.0 V, Snooze Mode
40
30
20
10
0
10u
100u
1m
10m
100m
Output Current (A)
1
OUTPUT VOLTAGE
vs
INPUT VOLTAGE
5.3
5.8
G006
1.86
TPS62080
VOUT = 2.5 V
1.84
Output Voltage (V)
Output Voltage (V)
3.8
4.3
4.8
Input Voltage (V)
OUTPUT VOLTAGE
vs
INPUT VOLTAGE
IOUT = 1A, TA = 25°C
IOUT = 1A, TA = −40°C
IOUT = 1A, TA = 85°C
IOUT = 10mA, TA = 25°C
IOUT = 10mA, TA = −40°C
IOUT = 10mA, TA = 85°C
3
3.5
4
4.5
Input Voltage (V)
5
5.5
TPS62081
VOUT = 1.8 V
1.82
1.80
1.78
IOUT = 1A, TA = 25°C
IOUT = 1A, TA = −40°C
IOUT = 1A, TA = 85°C
IOUT = 10mA, TA = 25°C
IOUT = 10mA, TA = −40°C
IOUT = 10mA, TA = 85°C
1.76
1.74
1.72
1.70
2.3
6
2.8
G007
3.3
3.8
4.3
4.8
Input Voltage (V)
Figure 10.
Figure 11.
OUTPUT VOLTAGE
vs
INPUT VOLTAGE
OUTPUT VOLTAGE
vs
LOAD CURRENT
3.36
5.3
5.8
G008
0.910
TPS62082
VOUT = 3.3 V
0.908
TPS62080
VIN = 3.6 V
0.906
Output Voltage (V)
3.32
Output Voltage (V)
3.3
Figure 9.
2.46
3.30
3.28
3.26
IOUT = 1A, TA = 25°C
IOUT = 1A, TA = −40°C
IOUT = 1A, TA = 85°C
IOUT = 10mA, TA = 25°C
IOUT = 10mA, TA = −40°C
IOUT = 10mA, TA = 85°C
3.24
3.22
3.20
3.8
4.3
4.8
Input Voltage (V)
Figure 12.
8
2.8
Figure 8.
2.48
3.18
3.3
TPS62080
VOUT = 0.9 V
G004
2.50
3.34
IOUT = 1A, TA = 25°C
IOUT = 1A, TA = −40°C
IOUT = 1A, TA = 85°C
IOUT = 10mA, TA = 25°C
IOUT = 10mA, TA = −40°C
IOUT = 10mA, TA = 85°C
0.890
0.880
2.3
3
2.52
2.44
2.5
0.895
0.885
2.56
2.54
0.900
Submit Documentation Feedback
5.3
0.904
0.902
0.900
0.898
0.896
TA = 25°C
TA = −40°C
TA = 85°C
0.894
0.892
0.890
10u
5.8
G009
100u
1m
10m
100m
Output Current (A)
1
3
G010
Figure 13.
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
TPS62080, TPS62080A
TPS62081, TPS62082
www.ti.com
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
OUTPUT VOLTAGE
vs
LOAD CURRENT
OUTPUT VOLTAGE
vs
LOAD CURRENT
2.54
1.84
TPS62081
VIN = 3.6 V
2.52
Output Voltage (V)
Output Voltage (V)
TPS62080
VIN = 3.6 V
2.50
2.48
2.46
10u
TA = 25°C
TA = −40°C
TA = 85°C
100u
1m
10m
100m
Output Current (A)
1
1.82
1.80
1.78
1.76
10u
3
1m
10m
100m
Output Current (A)
Figure 14.
Figure 15.
OUTPUT VOLTAGE
vs
LOAD CURRENT
QUIESCENT CURRENT
vs
INPUT VOLTAGE
Quiescent Current (A)
3.30
3.28
TA = 25°C
TA = −40°C
TA = 85°C
3.26
G012
100u
1m
10m
100m
Output Current (A)
1
35u
30u
25u
TA = 25°C
TA = −40°C
TA = 85°C
20u
15u
2.3
3
2.8
3.3
G013
3.8
4.3
4.8
Input Voltage (V)
Figure 16.
Figure 17.
QUIESCENT CURRENT
vs
INPUT VOLTAGE
HIGH SIDE FET RDS(on)
vs
INPUT VOLTAGE
9.5u
5.3
5.8
G016
250
FET On−Resistance (mΩ)
IOUT = 0 A, Snooze Mode
Quiescent Current (A)
3
IOUT = 0 A, Mode = Low
3.32
8u
6.5u
5u
TA = 25°C
TA = −40°C
TA = 85°C
3.5u
2u
2.3
1
40u
TPS62082
VIN = 3.6 V
Output Voltage (V)
100u
G011
3.34
3.24
10u
TA = 25°C
TA = −40°C
TA = 85°C
2.8
3.3
3.8
4.3
4.8
Input Voltage (V)
Figure 18.
Copyright © 2011–2012, Texas Instruments Incorporated
5.3
210
170
130
90
50
2.3
5.8
G017
TA = 25°C
TA = −40°C
TA = 85°C
2.8
3.3
3.8
4.3
4.8
Input Voltage (V)
5.3
5.8
G018
Figure 19.
Submit Documentation Feedback
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
9
TPS62080, TPS62080A
TPS62081, TPS62082
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
www.ti.com
LOW SIDE FET RDS(on)
vs
INPUT VOLTAGE
SWITCHING FREQUENCY
vs
LOAD CURRENT
3M
TA = 25°C
TA = −40°C
TA = 85°C
180
Switching Frequency (Hz)
FET On−Resistance (mΩ)
220
140
100
60
20
2.3
2.8
3.3
3.8
4.3
4.8
Input Voltage (V)
5.3
TPS62080
VOUT = 0.9V
2.5M
2M
1.5M
1M
VIN = 2.3V
VIN = 3.3V
VIN = 4.2V
VIN = 5.0V
500k
0
5.8
G019
0
400m
800m
Output Current (A)
1.2
Figure 20.
Figure 21.
SWITCHING FREQUENCY
vs
LOAD CURRENT
TYPICAL APPLICATION (PWM MODE)
1.6
G014
4.5M
Switching Frequency (Hz)
VIN = 2.5V
VIN = 3.3V
VIN = 4.2V
VIN = 5.0V
TPS62080
VOUT = 2.5V
4M
3.5M
3M
SW
2V/div
2.5M
2M
1.5M
VOUT
20mV/div
1M
500k
0
0
400m
800m
Output Current (A)
1.2
1.6
G015
L COIL
0.5A/div
t - 200ns/div
Figure 22.
10
Submit Documentation Feedback
Figure 23.
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
TPS62080, TPS62080A
TPS62081, TPS62082
www.ti.com
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
TYPICAL APPLICATION (PFM MODE)
TYPICAL APPLICATION (SNOOZE MODE)
SW
2V/div
SW
2V/div
VOUT
20mV/div
VOUT
50mV/div
L COIL
0.2A/div
L COIL
0.2A/div
t - 2µs/div
t - 50µs/div
Figure 24.
Figure 25.
LOAD TRANSIENT
LINE TRANSIENT
1A
LOAD
1A/div
4.2V
VIN
1V/div
50mA
3.3V
VOUT
20mV/div
VOUT
50mV/div
L COIL
1A/div
t - 50µs/div
Figure 26.
Copyright © 2011–2012, Texas Instruments Incorporated
t - 100µs/div
Figure 27.
Submit Documentation Feedback
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
11
TPS62080, TPS62080A
TPS62081, TPS62082
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
www.ti.com
START UP
START UP (WITHOUT LOAD)
EN
5V/div
EN
5V/div
PG
1V/div
PG
1V/div
VOUT
1V/div
VOUT
1V/div
L COIL
0.5A/div
L COIL
0.2A/div
t - 20µs/div
t - 20µs/div
Figure 28.
Figure 29.
SHUT DOWN
EN
5V/div
VOUT
0.5V/div
t - 20ms/div
Figure 30.
12
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
TPS62080, TPS62080A
TPS62081, TPS62082
www.ti.com
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
DETAILED DESCRIPTION
DEVICE OPERATION
The TPS6208x synchronous switched mode converters are based on DCS™ Control (Direct Control with
Seamless transition into Power Save Mode). This is an advanced regulation topology that combines the
advantages of hysteretic and voltage mode control.
The DCS™ Control topology operates in PWM (Pulse Width Modulation) mode for medium to heavy load
conditions and in Power Save Mode at light load currents. In PWM the converter operates with its nominal
switching frequency of 2MHz having a controlled frequency variation over the input voltage range. As the load
current decreases the converter enters Power Save Mode, reducing the switching frequency and minimizing the
IC quiescent current to achieve high efficiency over the entire load current range. DCS™ Control supports both
operation modes (PWM and PFM) using a single building block having a seamless transition from PWM to Power
Save Mode without effects on the output voltage. Fixed output voltage versions provide smallest solution size
combined with lowest quiescent current. The TPS6208x offers both excellent DC voltage and superior load
transient regulation, combined with very low output voltage ripple, minimizing interference with RF circuits.
The device is equipped with the Snooze Mode functionality, which is enabled with the Mode pin. The Snooze
Mode supports high efficiency conversion at lowest output currents below 2mA. If no load current is drawn, the
ultra low quiescent current of 6.5uA is sufficient to maintain the output voltage. This extends battery run time by
reducing the quiescent current during lowest or no load conditions in battery driven applications. For mainsoperated voltage supplies, the Snooze Mode reduces the system's stand-by energy consumption. During
shutdown (EN = LOW), the device reduces energy consumption to less than 1uA.
POWER SAVE MODE
As the load current decreases the TPS6208x will enter the Power Save Mode operation. During Power Save
Mode the converter operates with reduced switching frequency in PFM mode and with a minimum quiescent
current maintaining high efficiency. The power save mode occurs when the inductor current becomes
discontinuous. It is based on a fixed on time architecture. The typical on time is given by ton=210ns·(VOUT / VIN).
The switching frequency over the whole load current range is shown in Figure 21 and Figure 22.
SNOOZE MODE
The TPS6208x offers a Snooze Mode function. If the Snooze Mode is enabled by an external logic signal setting
the MODE pin to HIGH, the device's quiescent current consumption is reduced to typically 6.5µA. As a result, the
high efficiency range is extended towards the range of lowest output currents below 2mA, see the typical
characteristics efficiency figures.
If the device is operating in Snooze Mode, a dedicated, low power consuming block monitors the output voltage.
All other control blocks are snoozing during that time. If the output voltage falls below the programmed output
voltage by 3.5% (typ), the control blocks wake up, regulates the output voltage and allow themselves to snooze
again until the output voltage drops again. The Snooze Mode operation provides a clear efficiency improvement
at lowest output currents. If the load current increases, the advantage of efficiency in Snooze mode will be
deprived. Since the dynamic load regulation operates best if the Snooze Mode is disabled, it is recommended to
turn off the Snooze Mode by external logic signal if the load current exceeds 2mA, like a micro controller to
operate the MODE pin.
100% DUTY CYCLE LOW DROPOUT OPERATION
The device offers low input to output voltage difference by entering 100% duty cycle mode. In this mode the high
side MOSFET switch is constantly turned on and the low side MOSFET is switched off. This is particularly useful
in battery powered applications to achieve longest operation time by taking full advantage of the whole battery
voltage range. The minimum input voltage to maintain switching regulation, depending on the load current and
output voltage can be calculated as:
VIN,MIN = VOUT + IOUT,MAX ´ (RDS(on) + RL )
(1)
With:
VIN,MIN = Minimum input voltage
IOUT,MAX = Maximum output current
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
13
TPS62080, TPS62080A
TPS62081, TPS62082
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
www.ti.com
RDS(on) = High side FET on-resistance
RL = Inductor ohmic resistance
ENABLING / DISABLING THE DEVICE
The device is enabled by setting the EN input to a logic HIGH. Accordingly, a logic LOW disables the device. If
the device is enabled, the internal power stage will start switching and regulate the output voltage to the
programmed threshold. The EN input must be terminated with a resistance less than 1MΩ pulled to VIN or GND.
OUTPUT DISCHARGE
The output gets discharged by the SW pin with a typical discharge resistor of RDIS whenever the device shuts
down. This is the case when the device gets disabled by enable, thermal shutdown trigger, and undervoltage
lockout trigger.
SOFT START
After enabling the device, an internal soft-start circuitry monotonically ramps up the output voltage and reaches
the nominal output voltage during a soft start time (100µs, typical). This avoids excessive inrush current and
creates a smooth output voltage rise slope. It also prevents excessive voltage drops of primary cells and
rechargeable batteries with high internal impedance.
If the output voltage is not reached within the soft start time, such as in the case of heavy load, the converter will
enter regular operation. Consequently, the inductor current limit will operate as described below. The TPS6208x
is able to start into a pre-biased output capacitor. The converter starts with the applied bias voltage and ramps
the output voltage to its nominal value.
POWER GOOD
The TPS6208x has a power good output going low when the output voltage is below its nominal value. The
power good keeps high impedance once the output is above 95% of the regulated voltage, and is driven to low
once the output voltage falls below typically 90% of the regulated voltage. The PG pin is a open drain output and
is specified to sink typically up to 0.5mA. The power good output requires a pull up resistor that is recommended
connecting to the device output. When the device is off due to disable, UVLO or thermal shutdown, the PG pin is
at high impedance.
The PG signal can be used for sequencing of multiple rails by connecting to the EN pin of other converters.
Leave the PG pin unconnected when not used.
UNDER VOLTAGE LOCKOUT
To avoid mis-operation of the device at low input voltages, an under voltage lockout is implemented, that shuts
down the device at voltages lower than VUVLO with a VHYS_UVLO hysteresis.
THERMAL SHUTDOWN
The device goes into thermal shutdown once the junction temperature exceeds typically TJSD. Once the device
temperature falls below the threshold the device returns to normal operation automatically.
INDUCTOR CURRENT LIMIT
The Inductor Current Limit prevents the device from high inductor current and drawing excessive current from the
battery or input voltage rail. Excessive current might occur with a shorted/saturated inductor or a heavy
load/shorted output circuit condition.
The incorporated inductor peak current limit measures the current during the high side and low side power
MOSFET on-phase in PWM mode. Once the high side switch current limit is tripped, the high side MOSFET is
turned off and the low side MOSFET is turned on to reduce the inductor current. Until the inductor current drops
down to low side switch current limit, the low side MOSFET is turned off and the high side switch is turned on
again. This operation repeats until the inductor current does not reach the high side switch current limit. Due to
the internal propagation delay, the real current limit value can exceed the static current limit in the electrical
characteristics table.
14
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
TPS62080, TPS62080A
TPS62081, TPS62082
www.ti.com
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
APPLICATION INFORMATION
Output Filter Design
The inductor and the output capacitor together provide a low pass frequency filter. To simplify this process
Table 3 outlines possible inductor and capacitor value combinations for the most application.
Table 3. Matrix of Output Capacitor / Inductor Combinations
COUT [µF] (1)
L [µH] (1)
10
22
47
100
1
+
+ (2) (3)
+
+
2.2
+
+
+
+
150
0.47
4.7
(1)
(2)
(3)
Capacitance tolerance and bias voltage de-rating is anticipated. The effective capacitance can vary
by+20% and -50%. Inductor tolerance and current de-rating is anticipated. The effective inductance
can vary by +20% and -30%.
Plus mark indicates recommended filter combinations.
Filter combination in typical application.
Inductor Selection
Main parameter for the inductor selection is the inductor value and then the saturation current of the inductor. To
calculate the maximum inductor current under static load conditions, Equation 4 is given.
DI
IL,MAX = IOUT,MAX + L
2
VOUT
VIN
DIL = VOUT ´
L ´ fSW
1-
(2)
Where
IOUT,MAX = Maximum output current
ΔIL = Inductor current ripple
fSW = Switching frequency
L = Inductor value
It's recommended to choose the saturation current for the inductor 20%~30% higher than the IL,MAX, out of
Equation 4. A higher inductor value is also useful to lower ripple current, but will increase the transient response
time as well. The following inductors are recommended to be used in designs.
Table 4. List of Recommended Inductors
INDUCTANCE
[µH]
CURRENT RATING
[mA]
DIMENSIONS
L x W x H [mm3]
DC RESISTANCE
[mΩ typ]
1.0
2500
3 x 3 x 1.2
1.0
1650
3 x 3 x 1.2
2.2
2500
2.2
1600
TYPE
MANUFACTURER
35
XFL3012-102ME
Coilcraft
40
LQH3NPN1R0NJ0
Murata
4 x 3.7 x 1.65
49
LQH44PN2R2MP0
Murata
3 x 3 x 1.2
81
XFL3012-222ME
Coilcraft
Capacitor Selection
The input capacitor is the low impedance energy source for the converter which helps to provide stable
operation. A low ESR multilayer ceramic capacitor is recommended for best filtering and should be placed
between VIN and PGND as close as possible to that pins. For most applications 10μF will be sufficient, a larger
value reduces input current ripple.
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
15
TPS62080, TPS62080A
TPS62081, TPS62082
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
www.ti.com
The architecture of the TPS6208X allows to use tiny ceramic-type output capacitors with low equivalent series
resistance (ESR). These capacitors provide low output voltage ripple and are recommended. To keep its
resistance up to high frequencies and to get narrow capacitance variation with temperature, it's recommended to
use X7R or X5R dielectric. The TPS6208x is designed to operate with an output capacitance of 10µF to 100µF,
as outlined in Table 3.
Table 5. List of Recommended Capacitors
CAPACITANCE
[µF]
TYPE
DIMENSIONS
L x W x H [mm3]
MANUFACTURER
10
GRM188R60J106M
0603: 1.6 x 0.8 x 0.8
Murata
22
GRM188R60G226M
0603: 1.6 x 0.8 x 0.8
Murata
22
GRM21BR60J226M
0805: 2.0 x 1.2 x 1.25
Murata
Setting the Output Voltage
The TPS608x devices are available as fixed and adjustable output voltage versions. The fixed versions are
internally programmed to a fixed output voltage, whereas the adjustable output voltage version needs to be
programmed via an external voltage divider to set the desired output voltage.
Adjustable output voltage version
For the adjustable output voltage version, an external resistor divider is used. By selecting R1 and R2, the output
voltage is programmed to the desired value.
TPS62080
VIN
POWER GOOD
2.3V .. 6V
180k
VIN
PG
EN
SW
VOUT
VOS
22µF
1mH
10µF
MODE
R1
GND
FB
R2
Figure 31. Typical Application Circuit for Adjustable Output Voltage Option
When the output voltage is regulated, the typical voltage at the FB pin is VFB for the adjustable devices. The
following equation can be used to calculate R1 and R2.
R1 ö
R1 ö
æ
æ
VOUT = VFB ´ ç1 +
÷ = 0.45 V ´ ç1 +
÷
R
2
R
2ø
è
ø
è
(3)
For best accuracy, R2 should be kept smaller than 40kΩ to ensure that the current flowing through R2 is at least
100 times larger than IFB. Changing the sum towards a lower value increases the robustness against noise
injection. Changing the sum towards higher values reduces the quiescent current and supports the Snooze Mode
function for achieving highest efficiency at low load currents. For lowest quiescent current during the Snooze
Mode, it is recommended to use a fixed output voltage version like TPS62081 and TPS62082.
PCB Layout
The PCB layout is an important step to maintain the high performance of the TPS6208x devices.
The input/output capacitors and the inductor should be placed as close as possible to the IC. This keeps the
traces short. Routing these traces direct and wide results in low trace resistance and low parasitic inductance. A
common power GND should be used. The low side of the input and output capacitors must be connected
properly to the power GND to avoid a GND potential shift.
The sense traces connected to FB and VOS pins are signal traces. Special care should be taken to avoid noise
being induced. By a direct routing, parasitic inductance can be kept small. GND layers might be used for
shielding. Keep these traces away from SW nodes.
16
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
TPS62080, TPS62080A
TPS62081, TPS62082
www.ti.com
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
L
V IN
CIN
V OUT
1
COUT
GND
R1
R2
Figure 32. PCB Layout Suggestion
THERMAL INFORMATION
Implementation of integrated circuits in low-profile and fine-pitch surface-mount packages typically requires
special attention to power dissipation. Many system-dependent issues such as thermal coupling, airflow, added
heat sinks and convection surfaces, and the presence of other heat-generating components affect the powerdissipation limits of a given component.
Three basic approaches for enhancing thermal performance are listed below:
• Improving the power dissipation capability of the PCB design
• Improving the thermal coupling of the component to the PCB by soldering the ThermalPAD™
• Introducing airflow in the system
For more details on how to use the thermal parameters, see the application notes: Thermal Characteristics
Application Notes SZZA017 and SPRA953.
APPLICATION EXAMPLES
TPS62082
VIN
3.6V .. 6V
POWER GOOD
VIN
PG
EN
SW
180k
1µH
10µF
MODE
GND
VOS
3.3V
VOUT
22µF
FB
Figure 33. 3.3V Fixed Output Voltage Application (TPS62082)
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
17
TPS62080, TPS62080A
TPS62081, TPS62082
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
www.ti.com
TPS62080
VIN
POWER GOOD
2.3V .. 6V
VIN
PG
EN
SW
180k
1mH
10µF
MODE
1.2V
VOUT
22µF
VOS
65.3k
GND
FB
39.2k
Figure 34. 1.2V Output Voltage Application (TPS62080)
TPS62080
VIN
POWER GOOD
3.0V .. 6V
VIN
180k
PG
1mH
10µF
EN
MODE
2.5V
SW
VOUT
22µF
VOS
178.6k
GND
FB
39.2k
Figure 35. 2.5V Output Voltage Application (TPS62080)
18
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
TPS62080, TPS62080A
TPS62081, TPS62082
www.ti.com
SLVSAE8B – SEPTEMBER 2011 – REVISED MARCH 2012
REVISION HISTORY
Changes from Original (September 2011) to Revision A
Page
•
Added TPS62080A device .................................................................................................................................................... 1
•
Added TPS62080ADSG (Product Preview) and TPS62080ADGN (Product Preview) to ORDERING INFORMATION ...... 2
•
Added TPS62080A output discharge resistor ....................................................................................................................... 3
Changes from Revision A (February 2012) to Revision B
•
Page
Changed TPS62080ADSG from Product Preview to Production Data in ORDERING INFORMATION .............................. 2
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TPS62080 TPS62080A TPS62081 TPS62082
19
PACKAGE OPTION ADDENDUM
www.ti.com
31-Mar-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
TPS62080ADGNR
PREVIEW
MSOPPowerPAD
DGN
8
2500
TBD
Call TI
Call TI
TPS62080ADGNT
PREVIEW
MSOPPowerPAD
DGN
8
250
TBD
Call TI
Call TI
TPS62080ADSGR
ACTIVE
WSON
DSG
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
TPS62080ADSGT
ACTIVE
WSON
DSG
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
TPS62080DSGR
ACTIVE
WSON
DSG
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
TPS62080DSGT
ACTIVE
WSON
DSG
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
TPS62081DSGR
ACTIVE
WSON
DSG
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
TPS62081DSGT
ACTIVE
WSON
DSG
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
TPS62082DSGR
ACTIVE
WSON
DSG
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
TPS62082DSGT
ACTIVE
WSON
DSG
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
31-Mar-2012
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
30-Mar-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
TPS62080ADSGR
WSON
DSG
8
TPS62080ADSGT
WSON
DSG
TPS62080DSGR
WSON
DSG
TPS62080DSGT
WSON
TPS62081DSGR
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
8
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
8
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
DSG
8
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
WSON
DSG
8
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS62081DSGT
WSON
DSG
8
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS62082DSGR
WSON
DSG
8
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS62082DSGT
WSON
DSG
8
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
30-Mar-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS62080ADSGR
WSON
DSG
8
3000
195.0
200.0
45.0
TPS62080ADSGT
WSON
DSG
8
250
195.0
200.0
45.0
TPS62080DSGR
WSON
DSG
8
3000
195.0
200.0
45.0
TPS62080DSGT
WSON
DSG
8
250
195.0
200.0
45.0
TPS62081DSGR
WSON
DSG
8
3000
195.0
200.0
45.0
TPS62081DSGT
WSON
DSG
8
250
195.0
200.0
45.0
TPS62082DSGR
WSON
DSG
8
3000
195.0
200.0
45.0
TPS62082DSGT
WSON
DSG
8
250
195.0
200.0
45.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated