TI TLV320AC57N

TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
D
D
D
D
D
D
D
D
Single 3-V Operation
Low Power Consumption:
– Operating Mode . . . 20 mW Typ
– Standby Mode . . . 5 mW Typ
– Power-Down Mode . . . 2 mW Typ
Combined A/D, D/A, and Filters
Extended Variable-Frequency Operation
– Sample Rates up to 16 kHz
– Passband up to 7.2 kHz
Electret Microphone Bias Reference
Voltage Available
Drive a Piezo Speaker Directly
Compatible With All Digital Signal
Processors (DSPs)
D
D
D
Selectable Between 8-Bit Companded and
13-Bit (Dynamic Range) Linear Conversion:
– TLV320AC56 . . . µ-Law and Linear
Modes
– TLV320AC57 . . . A-Law and Linear
Modes
Programmable Volume Control in Linear
Mode
300-Hz to 3.6-kHz Passband with Specified
Master Clock
Designed for Standard 2.048-MHz Master
Clock for U.S. Analog, U.S. Digital, and
CT2, DECT, GSM, and PCS Standards for
Hand-Held Battery-Powered Telephones
PT PACKAGE
(TOP VIEW)
PDN
EARA
EARB
EARGS
VCC
MICMUTE
DCLKR
DIN
FSR
EARMUTE
1
20
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
11
MICBIAS
MICGS
MICIN
VMID
GND
LINSEL
TSX/DCLKX
DOUT
FSX
CLK
NC
NC
EARGS
EARB
EARA
PDN
MICBIAS
MICGS
MICIN
NC
NC
NC
DW OR N PACKAGE
(TOP VIEW)
48 47 46 45 44 43 42 41 40 39 38 37
NC
NC
NC
AVCC
NC
NC
NC
NC
DVCC
NC
MICMUTE
NC
1
36
2
35
3
34
4
33
5
32
6
31
7
30
8
29
9
28
10
27
11
26
12
25
VMID
NC
AGND
NC
NC
NC
NC
NC
NC
DGND
LINSEL
NC
NC
DCLKR
DIN
FSR
EARMUTE
NC
CLK
FSX
DOUT
TSX/DCLKX
NC
NC
13 14 15 16 17 18 19 20 21 22 23 24
NC – No internal connection
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
VBAP is a trademark of Texas Instruments Incorporated.
Copyright  1997, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
description
The TLV320AC56 and TLV320AC57 voice-band audio processor (VBAP) integrated circuits perform the
transmit encoding (A /D conversion) and receive decoding (D/A conversion) together with transmit and receive
filtering for voice-band communications systems. Cellular telephone systems are targeted in particular;
however, these integrated circuits can function in other systems including digital audio, telecommunications,
and data acquisition.
These devices are pin-selectable for either of two modes — companded and linear — providing data in two
formats. In the companded mode, data is transmitted and received in 8-bit words. In the linear mode, 13 bits
of data and either three bits of gain-setting control data, or three 0 bits of padding (to create a16-bit word), are
sent and received.
The transmit section is designed to interface directly with an electret microphone element. The microphone input
signal (MICIN) is buffered and amplified with provision for setting the amplifier gain to accommodate a range
of signal input levels. The amplified signal is passed through antialiasing and bandpass filters. The filtered signal
is then applied to the input of a compressing analog-to-digital converter (COADC) when companded mode is
selected. Otherwise, the analog-to-digital converter performs a linear conversion. The resulting data is then
clocked out of DOUT as a serial data stream.
The receive section converts a frame of serial data on DIN to analog through an expanding digital-to-analog
converter (EXDAC) when the companded mode is selected; otherwise, a linear conversion is performed. The
analog signal then passes through switched capacitor filters, which provide out-of-band rejection, (sin x)/x
correction functions, and smoothing. The filtered signal is sent to the earphone amplifier. The earphone amplifier
has a differential output with adjustable gain and is designed to minimize static power dissipation.
A single on-chip high-precision band-gap circuit generates all voltage references, eliminating the need for
external reference voltages. An internal reference voltage, VMID, equal to VCC /2 is used to develop the midlevel
virtual ground for all the amplifier circuits and the microphone bias circuit. Another reference voltage, MICBIAS,
can supply bias current for the microphone.
The TLV320AC5xC devices are characterized for operation from 0°C to 70°C. The TLV320AC5xI devices are
characterized for operation from – 40°C to 85°C.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
functional block diagram
LINSEL
15
MICMUTE
MICIN
6
18
Transmit
Third-Order
Antialias
Input
Buffer
Transmit
Sixth-Order
Low Pass
Transmit
First-Order
High Pass
Output
Logic
ADC
13
12
MICGS
19
256 kHz
VMID
VMID
MICBIAS
17
20
8 kHz
A/D
Converter
Voltage
Reference
VMID
Generator
D/A
Converter
Voltage
Reference
Autozero
14
Clock
Generator
Clock
Control
8 kHz
Receive
Buffer
5
VCC
Receive
Filter
16
GND
1
TSX/DCLKX
11 CLK
7
DCLKR
9
256 kHz
Earphone
Amplifier
FSX
Band-Gap
Voltage
Reference
256 kHz
2
EARA
3
EARB
4
EARGS
10
EARMUTE
DOUT
DAC
Input
Logic
8
FSR
DIN
15
LINSEL
PDN
NOTE A: Terminal numbers shown are for the DW and N packages.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
Terminal Functions
TERMINAL
NAME
I/O
NO.
DESCRIPTION
DW, N
PT
AGND
—
34
AVCC
CLK
—
4
11
19
I
Clock input. In the fixed-data-rate mode, CLK is the master clock input as well as the transmit and receive
data clock input . In the variable-data-rate mode, CLK is the master clock input only (digital).
DCLKR
7
14
I
Selection of fixed- or variable-data-rate operation. When DCLKR is connected to VCC, the device
operates in the fixed-data-rate mode. When DCLKR is not connected to VCC, the device operates in the
variable-data-rate mode and DCLKR becomes the receive data clock (digital).
DGND
—
27
8
15
I
Receive data input. Input data is clocked in on consecutive negative transitions of the receive data clock,
which is CLK for a fixed data rate and DCLKR for a variable data rate (digital).
DOUT
13
21
O
Transmit data output. Transmit data is clocked out on consecutive positive transitions of the transmit
data clock, which is CLK for a fixed data rate and DCLKX for a variable data rate (digital).
DVCC
—
9
EARA
2
44
O
Earphone output. EARA forms a differential drive when used with the EARB signal (analog).
EARB
3
45
O
Earphone output. EARB forms a differential drive when used with the EARA signal (analog).
EARGS
4
46
I
Earphone gain set input of feedback signal for the earphone output. The ratio of an external potential
divider network connected across EARA and EARB adjusts the power amplifier gain. Maximum gain
occurs when EARGS is connected to EARB. Minimum gain occurs when EARGS is connected to EARA.
Earphone frequency response correction is performed using an RC approach (analog).
10
17
I
Earphone output mute control signal. When EARMUTE is low, the output amplifier is disabled and no
audio is sent to the earphone (digital).
FSR
9
16
I
Frame-synchronization clock input for the receive channel. In the variable-data-rate mode, this signal
must remain high for the duration of the time slot. The receive channel enters the standby condition when
FSR is TTL-low for five frames or longer. The device enters a production test-mode condition when either
FSR or FSX is held high for five frames or longer (digital).
FSX
12
20
I
Frame synchronization clock input for the transmit channel. FSX operates independently of FSR, but
also in an analogous manner to FSR. The transmit channel enters the standby condition when FSX is
low for five frames or longer. The device enters a production test-mode condition when either FSX or
FSR is held high for five frames or longer (digital).
GND
16
—
LINSEL
15
26
I
Linear selection input. When low, LINSEL selects linear coding/decoding. When high, LINSEL selects
companded coding/decoding. Companding code on the ’AC56 is µ-law, and companding code on the
’AC57 is A-law (digital).
MICBIAS
20
42
O
Microphone bias. MICBIAS voltage for the electret microphone is equal to VMID.
MICGS
19
41
O
Output of the internal microphone amplifier. MICGS is used as the feedback to set the microphone
amplifier gain. If sidetone is required, it is accomplished by connecting a series network between MICGS
and EARGS (analog).
MICIN
DIN
EARMUTE
Ground return for all internal analog circuits
3-V supply voltage for all internal analog circuits
Ground return for all internal digital circuits
3-V supply voltage for all internal digital circuits
Ground return for all internal circuits
18
40
I
Microphone input. Electret microphone input to the internal microphone amplifier (analog)
MICMUTE
6
11
I
Microphone input mute control signal. When MICMUTE is active (low), zero code is transmitted (dig.).
PDN
1
43
I
Power-down input. When PDN is low, the device powers down to reduce power consumption (digital).
TSX/DCLKX
14
22
I/O
Transmit time slot strobe (active-low output) or data clock (input) for the transmit channel. In the
fixed-data-rate mode, TSX/DCLKX is an open-drain output that pulls to ground and is used as an enable
signal for a 3-state buffer. In the variable-data-rate mode, DCLKX becomes the transmit data clock input
(digital).
VCC
VMID
5
—
17
36
4
3-V supply voltage for all internal circuits
O
VCC /2 bias voltage reference. A pair of external, low-leakage, high-frequency capacitors
(1 µF and 470 pF) should be connected between VMID and ground for filtering.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 5.5 V
Output voltage range at DOUT, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 5.5 V
Input voltage range at DIN, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 5.5 V
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: Voltage value is with respect to GND.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
DW
1025 mW
8.2 mW/°C
656 mW
533 mW
N
1150 mW
9.2 mW/°C
736 mW
598 mW
PT
1075 mW
7.1 mW/°C
756 mW
649 mW
recommended operating conditions (see Note 2)
MIN
MAX
Supply voltage, VCC (see Note 3)
2.7
3.3
High-level input voltage, VIH
2.2
Low-level input voltage, VIL
Operating free-air
free air temperature,
temperature TA
50
TLV320AC56C, TLV320AC57C
TLV320AC56I, TLV320AC57I
V
Ω
600
Load capacitance between EARA and EARB, CL (see Note 4)
V
V
0.8
Load resistance between EARA and EARB, RL (see Note 4)
UNIT
0
70
– 40
85
nF
°C
NOTES: 2. To avoid possible damage to these CMOS devices and resulting reliability problems, the power-up sequence detailed in the system
reliability features paragraph should be followed.
3. Voltages at analog inputs, outputs, and VCC are with respect to GND.
4. RL and CL should not be applied simultaneously.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
electrical characteristics over recommended ranges of supply voltage and free-air temperature
(unless otherwise noted)
supply current, fDCLKR or fDCLKX = 2.048 MHz, outputs not loaded, VCC = 3 V, TA = 25°C
PARAMETER
ICC
Supply current from VCC
TEST CONDITIONS
MIN
Operating
PDN is high with CLK signal present
Power down
PDN is low for 500 µs
Standby – both
PDN is high with FSX and FSR held low
Standby – one
PDN is high with either FSX or FSR pulsing
with the other held low
MAX
UNIT
7.5
0.75
2
mA
4.5
digital interface
PARAMETER
TEST CONDITIONS
VOH
VOL
High-level output voltage
IIH
IIL
High-level input current, any digital input
Ci
Input capacitance
DOUT
Low-level output voltage
Low-level input current, any digital input
IOH = – 3.2 mA,
IOL = 3.2 mA,
VCC = 3 V
VCC = 3 V
MIN
TYP†
2.4
2.8
0.2
VI = 2.2 V to VCC
VI = 0 to 0.8 V
Co
Output capacitance
† All typical values are at VCC = 3 V, TA = 25°C.
MAX
UNIT
V
0.4
V
10
µA
10
µA
5
pF
5
pF
microphone interface
PARAMETER
TEST CONDITIONS
VIO
IIB
Input offset voltage at MICIN
B1
Ci
Unity-gain bandwidth, open loop at MICIN‡
AV
Large-signal voltage amplification at MICGS
IOmax
Maximum output current
MIN
TYP†
MAX
±5
VI = 0 to 3 V
± 200
Input bias current at MICIN
1.5
Input capacitance at MICIN
UNIT
mV
nA
MHz
5
pF
10 000
V/ V
VMID
3
µA
MICBIAS (source only)
1
mA
† All typical values are at VCC = 3 V, TA = 25°C.
‡ The frequency of the first pole is 100 Hz.
speaker interface
PARAMETER
TEST CONDITIONS
VO(PP)
VOO
AC output voltage
Output offset voltage at EARA, EARB (single-ended)
Relative to GND
II(lkg)
IOmax
Input leakage current at EARGS
VI = 0.5 V to (VCC – 0.5) V
RL = 600 Ω
ro
Output resistance at EARA, EARB
Maximum output current
TYP†
1
EARMUTE low, max level
when muted
Gain change
† All typical values are at VCC = 3 V, TA = 25°C.
§ 2.5 Vpp when VCC is 2.7 V.
6
MIN
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
– 60
MAX
3§
UNIT
80
mVpk
Vpp
± 200
nA
± 2.5
mA
Ω
dB
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
transmit gain and dynamic range, companded mode (µ-law or A-law) or linear mode selected, VCC = 3 V,
TA = 25°C (unless otherwise noted) (see Notes 5 and 6)
PARAMETER
TEST CONDITIONS
Transmit reference-signal level (0 dB) (see Note 7)
Overload-signal level (MICIN at unity gain)
Absolute gain error
MIN
Companded mode selected, µ-law (’AC56)
0.614
Companded mode selected, A-law (’AC57)
0.616
Linear mode selected (’AC56 and ’AC57)
0.626
Companded mode selected, µ-law (’AC56)
2.5
Companded mode selected, A-law (’AC57)
2.5
Linear mode selected (’AC56 and ’AC57)
2.5
±1
0-dB input signal
Gain error with input level relative to gain at –10 dBm0
MAX
MICIN to DOUT at 0 dBm0 to – 40 dBm0
± 0.5
MICIN to DOUT at – 41 dBm0 to – 50 dBm0
± 1.5
MICIN to DOUT at – 51 dBm0 to – 55 dBm0
±2
UNIT
Vrms
Vpp
dB
dB
VCC ± 10%, TA = 0°C to 70°C
± 0.5
dB
NOTES: 5. Unless otherwise noted, the analog input is 0 dB, 1020-Hz sine wave, where 0 dB is defined as the zero-reference point of the channel
under test.
6. The input amplifier is set for inverting unity gain.
7. The reference-signal level, which is input to the transmit channel, is defined as a value 3 dB below the full-scale value of 2 V.
Gain variation
transmit filter transfer, companded mode (µ-law or A-law) or linear mode selected, over recommended
ranges of supply voltage and free-air temperature, CLK = 2.048 MHz, FSX = 8 kHz (see Note 6)
PARAMETER
TEST CONDITIONS
fMICIN = 50 Hz
fMICIN = 200 Hz
Gain relative to input signal gain at 1.02 kHz
In ut am
Input
amplifier
lifier set for unity gain,
noninverting maximum gain output
signal
i
l at MICIN is
i 0 dB
fMICIN = 300 Hz to 3 kHz
fMICIN = 3.3 kHz
fMICIN = 3.4 kHz
fMICIN = 4 kHz
MIN
MAX
–10
0
–2.8
UNIT
0
±0.25
– 0.55
0.2
–1
– 0.1
dB
–14
fMICIN ≥ 4.6 kHz
– 32
NOTE 6. The input amplifier is set for inverting unity gain.
transmit idle channel noise and distortion, companded mode with µ-law or A-law selected, over
recommended ranges of supply voltage and operating free-air temperature (see Note 8)
PARAMETER
TEST CONDITIONS
Transmit noise, psophometrically weighted
MICIN connected to MICGS through a 10-kΩ resistor
Transmit noise, C-message weighted
MICIN connected to MICGS through a 10-kΩ resistor
Transmit signal-to-distortion ratio with sine-wave input
Intermodulation distortion, 2-tone CCITT method,
composite power level –13 dBm0
MIN
MAX
UNIT
– 72
dBm0p
10 dBrnC0
MICIN to DOUT at 0 dBm0 to – 24 dBm0
36
MICIN to DOUT at –25 dBm0 to – 30 dBm0
34
MICIN to DOUT at – 31 dBm0 to – 38 dBm0
30
MICIN to DOUT at – 39 dBm0 to – 40 dBm0
24
MICIN to DOUT at – 41 dBm0 to – 45 dBm0
20
CCITT G.712 (7.1), R2
49
CCITT G.712 (7.2), R3
51
dB
dB
NOTE 8: Transmit noise, linear mode: 200 µVrms is equivalent to –74 dB (referenced to device 0-dB level).
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
transmit idle channel noise and distortion, linear mode selected, over recommended ranges of supply
voltage and operating free-air temperature (see Notes 6 and 8)
PARAMETER
TEST CONDITIONS
Transmit noise
MIN
MICIN connected to MICGS through a 10-kΩ resistor
Transmit signal-to-distortion
signal to distortion ratio with sine-wave
sine wave input
MICIN to DOUT at 0 dBm0 to – 10 dBm0
46
MICIN to DOUT at – 11 dBm0 to – 12 dBm0
44
MICIN to DOUT at – 13 dBm0 to – 18 dBm0
40
MICIN to DOUT at – 19 dBm0 to – 24 dBm0
35
MICIN to DOUT at – 25 dBm0 to – 40 dBm0
20
MICIN to DOUT at – 41 dBm0 to – 45 dBm0
18
MAX
UNIT
200
µVrms
dB
NOTES: 6. The input amplifier is set for inverting unity gain.
8. Transmit noise, linear mode: 200 µVrms is equivalent to –74 dB (referenced to device 0-dB level).
receive gain and dynamic range, companded mode (µ-law or A-law) or linear mode selected, VCC = 3 V,
TA = 25°C (unless otherwise noted) (see Notes 9 and 10)
PARAMETER
TEST CONDITIONS
Receive reference-signal level (0 dB) (see Note 11)
Overload-signal level
Absolute gain error
MIN
Companded mode selected, µ-law (’AC56)
0.736
Companded mode selected, A-law (’AC57)
0.739
Linear mode selected (’AC56 and ’AC57)
0.751
Companded mode selected, µ-law (’AC56)
3
Companded mode selected, A-law (’AC57)
3
Linear mode selected (’AC56 and ’AC57)
3
±1
0-dB input signal
Gain error with output level relative to gain at –10 dBm0
MAX
DIN to EARA and EARB at 0 dBm0 to – 38 dBm0
± 0.5
DIN to EARA and EARB at – 39 dBm0 to – 50 dBm0
± 1.5
DIN to EARA and EARB at – 51 dBm0 to – 55 dBm0
±2
UNIT
Vrms
Vpp
dB
dB
VCC ±10%, TA = 0°C to 70°C
± 0.5
dB
NOTES: 9. Receive output is measured differentially in the maximum gain configuration. To set the output amplifier for maximum gain, EARGS
is connected to EARB and the output is taken between EARA and EARB. All output levels are (sin x)/x corrected.
10. Unless otherwise noted, the digital input is a word stream generated by passing a 0-dB sine wave at 1020 Hz through an ideal
encoder, where 0 dB is defined as the zero reference.
11. This reference-signal level is measured at the speaker output of the receive channel with the gain of the output speaker amplifier
set to unity.
Gain variation
receive filter transfer, companded mode (µ-law or A-law) or linear mode selected, over recommended ranges
of supply voltage and operating free-air temperature, FSR = 8 kHz (see Note 9)
PARAMETER
TEST CONDITIONS
fDIN = < 200 Hz
fDIN = 200 Hz
Gain relative to gain at 1.02 kHz
DIN = 0 dBm0
fDIN = 300 Hz to 3 kHz
fDIN = 3.3 kHz
fDIN = 3.4 kHz
fDIN = 4 kHz
MIN
MAX
UNIT
0.25
– 0.5
0.25
± 0.25
– 0.55
0.2
–1
– 0.1
dB
– 14
fDIN = > 4.6 kHz
– 30
NOTE 9. Receive output is measured differentially in the maximum gain configuration. To set the output amplifier for maximum gain, EARGS is
connected to EARB and the output is taken between EARA and EARB. All output levels are (sin x)/x corrected.
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
receive idle channel noise and distortion, companded mode with µ-law or A-law selected, over recommended
ranges of supply voltage and operating free-air temperature (see Note 9)
PARAMETER
TEST CONDITIONS
Receive noise, psophometrically weighted
DIN = 11010101 (A-law)
Receive noise, C-message weighted
DIN = 11111111 (µ-law)
Receive signal-to-distortion ratio with sine-wave input
MIN
MAX
UNIT
– 72
dBm0p
8 dBrnC0
DIN to EARA and EARB at 0 dBm0 to – 18 dBm0
36
DIN to EARA and EARB at – 19 dBm0 to – 24 dBm0
34
DIN to EARA and EARB at – 25 dBm0 to – 30 dBm0
30
DIN to EARA and EARB at – 31 dBm0 to – 38 dBm0
23
DIN to EARA and EARB at – 39 dBm0 to – 45 dBm0
17
dB
NOTE 9. Receive output is measured differentially in the maximum gain configuration. To set the output amplifier for maximum gain, EARGS is
connected to EARB and the output is taken between EARA and EARB. All output levels are (sin x)/x corrected.
receive idle channel noise and distortion, linear mode selected, over recommended ranges of supply voltage
and operating free-air temperature (see Notes 9 and 12)
PARAMETER
TEST CONDITIONS
Receive noise
MIN
DIN = 00000000
Receive signal-to-distortion ratio with sine-wave input
Intermodulation, 2-tone CCITT distortion method,
composite power level – 13 dBm0
DIN to EARA and EARB at 0 dBm0 to – 12 dBm0
46
DIN to EARA and EARB at – 13 dBm0 to – 18 dBm0
38
DIN to EARA and EARB at – 19 dBm0 to – 24 dBm0
32
DIN to EARA and EARB at – 25 dBm0 to – 40 dBm0
18
DIN to EARA and EARB at – 41 dBm0 to – 45 dBm0
15
CCITT G.712 (7.1), R2
50
CCITT G.712 (7.2), R3
54
MAX
UNIT
200
µVrms
dB
dB
NOTES: 9. Receive output is measured differentially in the maximum gain configuration. To set the output amplifier for maximum gain, EARGS
is connected to EARB and the output is taken between EARA and EARB. All output levels are (sin x)/x corrected.
12. Receive noise, linear mode: 200 µVrms is equivalent to –71 dB (referenced to device 0-dB level).
power supply rejection and crosstalk attenuation over recommended ranges of supply voltage and
operating free-air temperature
PARAMETER
TEST CONDITIONS
MIN
TYP†
MAX
UNIT
Supply voltage rejection, transmit channel
Idle channel, supply signal = 100 mVrms,
f = 0 to 30 kHz (measured at DOUT)
– 30
dB
Supply voltage rejection, receive channel
Idle channel, supply signal = 100 mVrms,
EARGS connected to EARB,
f = 0 to 30 kHz (measured differentially
between EARA and EARB)
– 30
dB
Crosstalk attenuation, transmit-to-receive (differential)
MICIN = 0 dB, f = 1.02 kHz,
unity transmit gain,
EARGS connected to EARB, measured
differentially between EARA and EARB
50
dB
Crosstalk attenuation, receive-to-transmit
DIN = 0 dBm0, f = 1.02 kHz,
unity transmit gain, measured at DOUT
50
dB
† All typical values are at VCC = 3 V, TA = 25°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
timing requirements
clock timing requirements over recommended ranges of supply voltage and operating free-air temperature
(unless otherwise noted) (see Figure 1 through Figure 4)
MIN
tt
NOM†
MAX
Transition time, CLK and DCLKX /DCLKR
10
Duty cycle, CLK
45%
50%
55%
Duty cycle, DCLKX /DCLKR
45%
50%
55%
UNIT
ns
† All nominal values are at VCC = 3 V, TA = 25°C.
transmit timing requirements over recommended ranges of supply voltage and operating free-air
temperature, fixed-data-rate mode (see Figure 2)
tsu(FSX)
th(FSX)
MIN
MAX
UNIT
Setup time, FSX high before CLK↓
20
468
ns
Hold time, FSX high after CLK↓
20
468
ns
receive timing requirements over recommended ranges of supply voltage and operating free-air
temperature, fixed-data-rate mode (see Figure 1)
MIN
MAX
UNIT
tsu(FSR)
th(FSR)
Setup time, FSR high before CLK↓
20
468
ns
Hold time, FSR high after CLK↓
20
468
ns
tsu(DIN)
th(DIN)
Setup time, DIN high or low before CLK↓
20
ns
Hold time, DIN high or low after CLK↓
20
ns
transmit timing requirements over recommended ranges of supply voltage and operating free-air
temperature, variable-data-rate mode (see Figure 4)
MIN
tsu(FSX)
th(FSX)
Setup time, FSX high before DCLKX↓
MAX
UNIT
40 tc(DCLKX)– 40
35 tc(DCLKX)–35
Hold time, FSX high after DCLKX↓
ns
ns
receive timing requirements over recommended ranges of supply voltage and operating free-air
temperature, variable-data-rate mode (see Figure 3)
MIN
MAX
UNIT
tsu(FSR)
th(FSR)
Setup time, FSR high before DCLKR↓
40
Hold time, FSR high after DCLKR↓
35
ns
tsu(DIN)
th(DIN)
Setup time, DIN high or low before DCLKR↓
30
ns
Hold time, DIN high or low after DCLKR↓
30
ns
tc(DCLKR)–35
ns
switching characteristics
propagation delay times over recommended ranges of operating conditions, fixed-data-rate mode,
CL = 0 to 10 pF (see Figure 2)
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
tpd1
tpd2
From CLK bit 1 high to DOUT bit 1 valid
35
ns
From CLK high to DOUT valid, bits 2 to n
35
ns
tpd3
tpd4
From CLK bit n low to DOUT bit n Hi-Z
From CLK bit 1 high to TSX active (low)
Rpullup = 1.24 kW
tpd5
From CLK bit n low to TSX inactive (high)
Rpullup = 1.24 kΩ
10
30
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
ns
40
30
ns
ns
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
propagation delay times over recommended ranges of operating conditions, variable-data-rate mode (see
Figure 4)
PARAMETER
TEST CONDITIONS
MIN
MAX
UNIT
tpd6
tpd7
FSX high to DOUT bit 1 valid
CL = 0 to 10 pF
30
ns
DCLKX high to DOUT valid, bits 2 to n
CL = 0 to 10 pF
40
ns
tpd8
FSX low to DOUT bit n Hi-Z
20
ns
PARAMETER MEASUREMENT INFORMATION
All timing parameters are referenced to VIH and VIL. Bit 1 = MSB (most significant bit) and is clocked in first on DIN
or clocked out first on DOUT. Bit N = LSB (least significant bit) and is clocked in last on DIN or is clocked out last on
DOUT. N = 8 for the companded mode, and N = 16 for the linear mode.
Receive Time Slot
0
1
2
3
4
N–2
80%
CLK
N–1
N
N+1
80%
20%
20%
tsu(FSR)
th(FSR)
FSR
See Note B
See Note A
DIN
N–1
N
th(DIN)
1
2
3
4
N–2
N–1
N
1
See Note C
tsu(DIN)
NOTES: A. This window is allowed for FSR high.
B. This window is allowed for FSR low.
C. Transitions are measured at 50%.
Figure 1. Fixed-Data Rate Mode, Receive Side Timing Diagram
0
1
2
Transmit Time Slot
4
N–2
3
N–1
N
CLK
20%
tsu(FSX)
N+1
80%
80%
20%
th(FSX)
FSX
See Note B
See Note A
1
DOUT
See Note C
TSX
tpd2
2
3
tpd3
N–2
N–1
tpd1
N
tpd5
80%
20%
tpd4
NOTES: A. This window is allowed for FSX high.
B. This window is allowed for FSX low (th(FSX) max determined by data collision considerations).
C. Transitions are measured at 50%.
Figure 2. Fixed-Data Rate Mode, Transmit Side Timing Diagram
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
PARAMETER MEASUREMENT INFORMATION
Receive Time Slot
0
1
80%
DCLKR
2
3
4
N–2
N–1
N
80%
20%
N+1
80%
20%
tsu(FSR)
th(FSR)
FSR
See Note A
DIN
N–1
th(DIN)
N
1
2
3
4
See Note B
N–2
N–1
See Note C
N
1
tsu(DIN)
NOTES: A. This window is allowed for FSR high (tsu(FSR) max determined by data collision considerations).
B. This window is allowed for FSR low.
C. Transitions are measured at 50%.
Figure 3. Variable-Data Rate Mode, Receive Side Timing Diagram
0
1
2
80%
DCLKX
Transmit Time Slot
4
N–2
3
N–1
N
80%
20%
20%
th(FSX)
tsu(FSX)
FSX
tpd7
See Note A
See Note B
tpd8
tpd6
DOUT
See Note C
1
2
3
4
N–2
N–1
NOTES: A. This window is allowed for FSX high.
B. This window is allowed for FSX low without data repetition.
C. Transitions are measured at 50%.
Figure 4. Variable-Data Rate Mode, Transmit Side Timing Diagram
12
POST OFFICE BOX 655303
N+1
80%
• DALLAS, TEXAS 75265
N
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
PRINCIPLES OF OPERATION
general
system reliability features
The device should be powered up and initialized as follows:
1.
2.
3.
4.
5.
Apply GND.
Apply VCC.
Connect all clocks.
Apply TTL high to PDN.
Apply synchronizing pulses to FSX and/or FSR.
Even though the VBAP is heavily protected against latch-up, it is still possible to cause it to latch up under certain
improper power conditions. To help ensure that latch-up does not occur, a reverse-biased Schottky diode with
a forward voltage drop of less than or equal to 0.4 V (1N5711 or equivalent) should be connected between VCC
(power supply) and GND.
On the transmit channel, digital outputs DOUT and TSX are held in the high-impedance state for approximately
four frames (500 µs) after power up or application of VCC. After this delay, DOUT, TSX, and signaling are
functional and occur in the correct time slot. The analog circuits on the transmit side require approximately
60 ms to reach their equilibrium value due to the autozero circuit settling time. To further enhance system
integrity, DOUT and TSX are placed in the high-impedance state after an interruption of CLK.
power-down and standby operations
To minimize power consumption, a power-down mode and three standby modes are provided.
For power down, an external low signal is applied to PDN. In the absence of a signal, PDN is internally pulled
up to a high logic level and the device remains active. In the power-down mode, the average power consumption
is reduced to 2 mW.
Three standby modes give the user the option of placing the entire device on standby, placing only the transmit
channel on standby, or placing only the receive channel on standby. To place the entire device on standby, both
FSX and FSR are held low. For transmit-only operation (receive channel on standby), FSX is pulsing and FSR
is held low. For receive-only operation (transmit section on standby), FSR is pulsing and FSX is held low. When
the entire device is in standby mode, power consumption is reduced to 5 mW. See Table 1 for power-down and
standby procedures.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
PRINCIPLES OF OPERATION
Table 1. Power-Down and Standby Procedures
DEVICE STATUS
PROCEDURE
TYPICAL POWER
CONSUMPTION
DIGITAL OUTPUT STATUS
Power on
PDN = high,
FSX = pulses,
FSR = pulses
Power down
PDN = low,
FSX, FSR = X†
2 mW
TSX and DOUT in the high-impedance state
Entire device on standby
mode
FSX = low,
FSR = low,
PDN = high
5 mW
TSX and DOUT in the high-impedance state
Only transmit channel in
standby mode
FSX = low,
FSR = pulses,
PDN = high
10 mW
TSX and DOUT in the high-impedance state within five
frames
Only receive channel in
standby mode
FSR = low,
FSX = pulses,
PDN = high
10 mW
Digital outputs active but not loaded
20 mW
Digital outputs active but not loaded
† X = don’t care
fixed-data-rate timing
Fixed-data-rate timing is selected by connecting DCLKR to VCC and uses the master clock (CLK), frame
synchronization clocks (FSX and FSR), and the TSX output. FSX and FSR are inputs that set the sampling
frequency. Data is transmitted on DOUT on the positive transitions of CLK following the rising edge of FSX. Data
is received on DIN on the falling edges of CLK following FSR. A D/A conversion is performed on the received
digital word, and the resulting analog sample is held on an internal sample-and-hold capacitor until transferred
to the receive filter. The data word is eight bits long in the companded mode and 16 bits long in the linear mode.
variable-data-rate timing
Variable-data-rate timing is selected by connecting DCLKR to the receive data clock. In this mode, the master
clock (CLK) controls the switched-capacitor filters, while data transfer into DIN and out of DOUT is controlled
by DCLKR and DCLKX respectively. This allows the data to be transferred in and out of the device at any rate
up to the frequency of the master clock. DCLKR and DCLKX must be synchronous with CLK.
While the FSX input is high, data is transmitted from DOUT on consecutive positive transitions of DCLKX.
Similarly, while the FSR input is high, the data word is received at DIN on consecutive negative transitions of
DCLKR. The transmitted data word at DOUT is repeated in all remaining time slots in the frame as long as
DCLKX is pulsed and FSX is held high. This feature, which allows the data word to be transmitted more than
once per frame, is available only with variable-data-rate timing.
asynchronous operations
To avoid crosstalk problems associated with special interrupt circuits, the design includes separate converters,
filters, and voltage references on the transmit and receive sides to allow completely independent operation of
the two channels. In either timing mode, the master clock, data clock, and time-slot strobe must be synchronized
at the beginning of each frame.
precision voltage references
A precision band-gap reference voltage is generated internally and is used to supply all the references required
for operation of both the transmit and receive channels. The gain in each channel is trimmed during the
manufacturing process. This ensures very accurate, stable gain performance over variations in supply voltage
and device temperature.
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
PRINCIPLES OF OPERATION
conversion laws
The TLV320AC56 provides µ-law companding operation that approximates the CCITT G.711 recommendation.
The TLV320AC57 provides A-law companding operation that approximates the CCITT G.711 recommendation.
The linear mode of operation uses a 13-bit two’s-complement format and is the same for both the TLV320AC56
and the TLV320AC57.
transmit operation
microphone input
The microphone input amplifier is designed specifically to interface to electret-type microphone elements, as
shown in Figure 5. The VMID buffer circuit provides a voltage (MICBIAS) equal to 1/2 VCC as a reference for
the microphone amplifier and a bias voltage to the electret microphone. The microphone amplifier output
(MICGS) is used in conjunction with a feedback network and applied to the amplifier inverting input (MICIN) to
set the amplifier gain. VMID appears at a terminal to provide a place to filter the VMID voltage.
VMID
17
1 µF
VMID Reference
For Amplifiers
470 pF
VMID Buffer
10 kΩ
3.3 µF
+
10 kΩ
Electret
Microphone
MICGS
19
VMID
Generator
+
+
MICBIAS
20
2 kΩ
VDD
–
–
Microphone Amplifier
MICIN
18
–
To Transmit Filters
+
MICMUTE
TLV320AC56/57 VBAP
6
NOTE A: Terminal numbers shown are for the DW and N packages.
Figure 5. Typical Microphone Interface
microphone mute function
The MICMUTE input causes the digital circuitry to transmit all zero code on DOUT.
transmit filter
A low-pass antialiasing section is included on the device and achieves a 35-dB attenuation at the sampling
frequency. No external components are required to provide the necessary antialiasing function for the
switched-capacitor section of the transmit filter.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
PRINCIPLES OF OPERATION
encoding
The encoder internally samples the output of the transmit filter and holds each sample on an internal
sample-and-hold capacitor. The encoder performs an A/D conversion on a switched-capacitor array. Digital
data representing the sample is transmitted on the first 8 or 16 data clock cycles of the next frame.
The autozero circuit corrects for dc offset on the input signal to the encoder using the sign-bit averaging
technique. The sign bit from the encoder output is long-term averaged and subtracted from the input to the
encoder.
data word structure
The data word is eight bits long in the companded mode and all eight bits represent one audio data sample.
The sign bit is the first bit transmitted.
The data word is 16 bits long in the linear mode. The first 13 bits comprise the audio data sample, and the last
three bits form the volume control word in the receive direction (DIN) and are zero pad bits in the transmit
direction (DOUT). The sign bit is transmitted first.
receive operation
decoding
In the companded mode, the serial data word is received at DIN on the first eight clock cycles in fixed-data rate
and on the last eight clock cycles in variable-data rate. In the linear mode, the serial data word is received at
DIN on the first 13 clock cycles. D/A conversion is performed, and the corresponding analog sample is held on
an internal sample-and-hold capacitor. This sample is transferred to the receive filter.
receive filter
The receive section of the filter provides passband flatness and stopband rejection that approximates both the
AT&T D3/D4 specification and CCITT recommendation G.712 when operated at the recommended
frequencies. The filter contains the required compensation for the (sin x)/x response of such decoders.
receive buffer
The receive buffer contains the volume control.
earphone amplifier
The earphone audio-output amplifier has a balanced output, as shown in Figure 6, to allow maximum flexibility
in output configuration. The output amplifier is designed to directly drive a piezo earphone in the differential
configuration without any additional external components. The output can also be used to drive a single-ended
load with the output signal voltage centered around VCC /2.
The receive-channel output level can be adjusted between specified limits by connecting an external resistor
network to EARGS.
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
PRINCIPLES OF OPERATION
–
+
IN
_
4
2
+
_
VMID
3
EARGS
EARA
EARB
+
NOTE A: Terminal numbers shown are for the DW and N packages.
Figure 6. Earphone Audio-Output Amplifier Configuration and Internal Gain-Setting Network
receive data format
In the companded mode, eight bits of data are received. The sign bit is the first bit received (see Table 2).
In the linear mode, 16 bits of data are received. The first 13 bits are the D/A code, and the remaining three bits
form the volume control word (see Table 2). The volume control function is actually an attenuation control in
which the first bit received is the most significant. The maximum volume occurs when all three volume control
bits are zero. Eight levels of attenuation are selectable in 3-dB steps, giving a maximum attenuation of 21 dB
when all bits are 1s. The volume control bits are not latched into the VBAP and must be present in each received
data word.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
PRINCIPLES OF OPERATION
Table 2. Receive-Data Bit Definitions
BIT NO.
COMPANDED MODE
LINEAR MODE
0
CD7
LD12
1
CD6
LD11
2
CD5
LD10
3
CD4
LD9
4
CD3
LD8
5
CD2
LD7
6
CD1
LD6
7
CD0
LD5
8
–
LD4
9
–
LD3
A
–
LD2
B
–
LD1
C
–
LD0
D
–
V2
E
–
V1
F
–
V0
Volume control and other control bits always follow the PCM data in time:
Companded Mode:
MSB
(sign bit)
LSB
CD7 CD6 CD5 CD4 CD3 CD2 CD1 CD0
Companded Data
Linear Mode:
MSB
(sign bit)
LSB
LD12 LD11 LD10 LD9 LD8 LD7 LD6 LD5 LD4 LD3 LD2 LD1 LD0
Linear Data
Time
where:
CD7– CD0 = Data word when in companded mode
LD12– LD0 = Data word when in linear mode
V2, V1, V0 = Volume (attenuation control) 000 = maximum volume, 3 dBm0
111 = minimum volume, –18 dBm0
18
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
V2
V1
V0
Volume Control
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
APPLICATION INFORMATION
output gain set design considerations (see Figure 7)
EARA and EARB are low-impedance complementary outputs. The voltages at the nodes are:
VO + at EARA
VO – at EARB
VOD = VO + – VO – (total differential response)
R1 and R2 are a gain-setting resistor network with the center tap connected to EARGS.
A value greater than 10 kΩ and less than 100 kΩ for R1 + R2 is recommended because of the following:
The parallel combination R1 + R2 and RL sets the total loading. The total capacitance at EARGS and the
parallel combination of R1 and R2 define a time constant that has to be minimized to avoid inaccuracies.
VA represents the maximum available digital mW output response (VA = 1.001 Vrms).
VOD = A × VA
where A =
1 + (R1/R2)
4 + (R1/R2)
EARA
2
VO+
R1
Digital mW Sequence
IAW CCITT G.712
DIN
EARGS
4
VO
RL
R2
EARB
3
VO –
NOTE A: Terminal numbers shown are for the DW and N packages.
Figure 7. Gain-Setting Configuration
higher clock frequencies and sample rates
The VBAP is designed to work with sample rates up to 16 kHz where the frequency of the frame sync determines
the sampling frequency. However, there is a fundamental requirement to maintain the ratio of the master clock
frequency, fCLK, to the frame sync frequency, fFSR/fFSX. This ratio for the VBAP is 2.048 MHz/8 kHz, or 256
master clocks per frame sync. For example, to operate the VBAP at a sampling rate of fFSR and fFSX equal to
16 kHz, fCLK must be 256 times 16 kHz, or 4.096 MHz. If the VBAP is operated above an 8-kHz sample rate,
however, it is expected that the performance becomes somewhat degraded. Exact parametric specifications
for rates up to 16-kHz sample rate are not specified at this time.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
MECHANICAL DATA
DW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
16 PIN SHOWN
PINS **
0.050 (1,27)
16
20
24
28
A MAX
0.410
(10,41)
0.510
(12,95)
0.610
(15,49)
0.710
(18,03)
A MIN
0.400
(10,16)
0.500
(12,70)
0.600
(15,24)
0.700
(17,78)
DIM
0.020 (0,51)
0.014 (0,35)
16
0.010 (0,25) M
9
0.419 (10,65)
0.400 (10,15)
0.299 (7,59)
0.293 (7,45)
0.010 (0,25) NOM
Gage Plane
0.010 (0,25)
1
8
0°– 8°
A
0.050 (1,27)
0.016 (0,40)
Seating Plane
0.104 (2,65) MAX
0.012 (0,30)
0.004 (0,10)
0.004 (0,10)
4040000 / B 03/95
NOTES: A.
B.
C.
D.
20
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15).
Falls within JEDEC MS-013
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
MECHANICAL DATA
N (R-PDIP-T**)
PLASTIC DUAL-IN-LINE PACKAGE
16 PIN SHOWN
PINS **
14
16
18
20
A MAX
0.775
(19,69)
0.775
(19,69)
0.920
(23.37)
0.975
(24,77)
A MIN
0.745
(18,92)
0.745
(18,92)
0.850
(21.59)
0.940
(23,88)
DIM
A
16
9
0.260 (6,60)
0.240 (6,10)
1
8
0.070 (1,78) MAX
0.035 (0,89) MAX
0.310 (7,87)
0.290 (7,37)
0.020 (0,51) MIN
0.200 (5,08) MAX
Seating Plane
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.015 (0,38)
0.010 (0,25) M
0°– 15°
0.010 (0,25) NOM
14/18 PIN ONLY
4040049/C 08/95
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001 (20 pin package is shorter then MS-001.)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
21
TLV320AC56, TLV320AC57
3-V VOICE-BAND AUDIO PROCESSORS (VBAP)
SLWS044B – JUNE 1996 – REVISED OCTOBER 1997
MECHANICAL DATA
PT (S-PQFP-G48)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
36
0,08 M
25
37
24
48
13
0,13 NOM
1
12
5,50 TYP
7,20
SQ
6,80
9,20
SQ
8,80
Gage Plane
0,25
0,05 MIN
1,45
1,35
Seating Plane
1,60 MAX
0°– 7°
0,75
0,45
0,10
4040052 / B 03/95
NOTES: A.
B.
C.
D.
22
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Falls within JEDEC MO-136
This may also be a thermally-enhanced plastic package with leads connected to the die pads.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments (TI) reserves the right to make changes to its products or to discontinue any semiconductor
product or service without notice, and advises its customers to obtain the latest version of relevant information
to verify, before placing orders, that the information being relied on is current.
TI warrants performance of its semiconductor products and related software to the specifications applicable at
the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are
utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each
device is not necessarily performed, except those mandated by government requirements.
Certain applications using semiconductor products may involve potential risks of death, personal injury, or
severe property or environmental damage (“Critical Applications”).
TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED
TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS.
Inclusion of TI products in such applications is understood to be fully at the risk of the customer. Use of TI
products in such applications requires the written approval of an appropriate TI officer. Questions concerning
potential risk applications should be directed to TI through a local SC sales office.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards should be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance, customer product design, software performance, or
infringement of patents or services described herein. Nor does TI warrant or represent that any license, either
express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property
right of TI covering or relating to any combination, machine, or process in which such semiconductor products
or services might be or are used.
Copyright  1997, Texas Instruments Incorporated