P600A THRU P600M GENERAL PURPOSE PLASTIC RECTIFIER Reverse Voltage - 50 to 1000 Volts Forward Current - 6.0 Amperes Case Style P600 FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High forward current capability ♦ Construction utilizes void-free molded plastic technique ♦ High surge current capability ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375” (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.360 (9.1) 0.340 (8.6) 0.360 (9.1) 0.340 (8.6) MECHANICAL DATA 0.052 (1.32) 0.048 (1.22) DIA. Case: Void-free molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.07 ounce, 2.1 grams 1.0 (25.4) MIN. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS P600A P600B P600D P600G P600J P600K P600M UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current at TA=60°C, 0.375" (9.5mm) lead length (FIG 1) TL=60°C, 0.125" (3.18mm) lead length (FIG 2) I(AV) 6.0 22.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 400.0 Amps Maximum instantaneous forward voltage at: 6.0A 100A VF 0.90 1.30 Maximum DC reverse current at rated DC blocking voltage IR 5.0 1.0 µA mA Typical junction capacitance (NOTE 1) CJ 150.0 pF Typical reverse recovery time (NOTE 2) trr 2.5 µS RΘJA RΘJL 20.0 4.0 °C/W TJ, TSTG -50 to +150 °C TA= 25°C TA=100°C Typical thermal resistance (NOTE 3) Operating junction and storage temperature range NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Reverse recovery time conditions: IF=0.5A, IR=1.0A, Irr=0.25A (3) Thermal resistance from junction to ambient and from junction to lead at 0.375” (9.5mm) lead length, P.C.B. mounted with 1.1 x 1.1 (30 x 30mm) copper pads 10/12/98 1.0 1.4 Volts RATINGS AND CHARACTERISTIC CURVES P600A THRU P600M AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG.1 - MAXIMUM FORWARD CURRENT DERATING CURRENT FIG. 2 - MAXIMUM FORWARD CURRENT DERATING CURVE 60 HZ RESISTIVE OR INDUCTIVE LOAD AVERAGE FORWARD CURRENT, AMPERES L=0.125” (3.18mm) 1.1 x 1.1” (30 x 30mm) COPPER PADS STANDARD P.C.B. MOUNTING 0.375” (9.5mm) LEAD LENGTH L=0.25” (6.35mm) 60 HZ RESISTIVE OR INDUCTIVE LOAD BOTH LEADS ATTACHED to HEAT SINKS WITH LENGTH as SHOWN, L L=0.375” (9.5mm) L=0.625” (15.8mm) AMBIENT TEMPERATURE, °C LEAD TEMPERATURE, °C FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT, AMPERES FIG. 3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, AMPERES 8.3 SINGLE HALF SINE-WAVE (JEDEC Method) TA=25°C TJ=150°C NUMBER OF CYCLES AT 60 HZ TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE FIG. 5 - TYPICAL REVERSE CHARACTERISTIC INSTANTANEOUS FORWARD VOLTAGE, VOLTS TJ=125°C TJ=100°C TJ=25°C TRANSIENT THERMAL IMPEDANCE, °C/W INSTANTANEOUS REVERSE CURRENT, MICROAMPERES FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE t, PULSE DURATION, sec. PERCENT OF RATED PEAK REVERSE VOLTAGE, %