SN74LVC1GU04 SINGLE INVERTER SCES215B – APRIL 1999 – REVISED AUGUST 1999 D D D D D EPIC (Enhanced-Performance Implanted CMOS) Submicron Process Unbuffered Output Ioff Feature Supports Partial-Power-Down Mode Operation Supports 5-V VCC Operation Package Options Include Plastic Small-Outline Transistor (DBV, DCK) Packages DBV OR DCK PACKAGE (TOP VIEW) NC A GND 1 5 VCC 4 Y 2 3 NC – No internal connection description This single inverter is designed for 1.65-V to 5.5-V VCC operation. The SN74LVC1GU04 contains one inverter with an unbuffered output, and performs the Boolean function Y = A. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. PRODUCT PREVIEW The SN74LVC1GU04 is characterized for operation from –40°C to 85°C. FUNCTION TABLE INPUT A OUTPUT Y H L L H logic symbol† A 2 4 1 Y † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. logic diagram (positive logic) A 2 4 Y Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. EPIC is a trademark of Texas Instruments Incorporated. Copyright 1999, Texas Instruments Incorporated PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN74LVC1GU04 SINGLE INVERTER SCES215B – APRIL 1999 – REVISED AUGUST 1999 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 6.5 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 6.5 V Output voltage range, VO (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Continuous output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA Package thermal impedance, θJA (see Note 3): DBV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347°C/W DCK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C PRODUCT PREVIEW † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The value of VCC is provided in the recommended operating conditions table. 3. The package thermal impedance is calculated in accordance with JESD 51. recommended operating conditions VCC VIH VIL VI VO Supply voltage High level input voltage High-level Low level input voltage Low-level Operating Data retention only VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V VCC = 4.5 V to 5.5 V MIN MAX 1.65 5.5 1.5 IOL 2 V 0.65 × VCC 1.7 V 2 0.7 × VCC 0.35 × VCC VCC = 1.65 V to 1.95 V VCC = 2.3 V to 2.7 V 0.7 VCC = 2.7 V to 3.6 V VCC = 4.5 V to 5.5 V 0.8 V 0.3 × VCC Input voltage 0 5.5 V Output voltage 0 VCC –4 V VCC = 1.65 V VCC = 2.3 V IOH UNIT High-level output current Low-level output current ∆t/∆v Input transition rise or fall rate TA Operating free-air temperature –8 VCC = 2.7 V VCC = 3 V –12 VCC = 4.5 V VCC = 1.65 V –32 4 VCC = 2.3 V VCC = 2.7 V VCC = 3 V 8 12 32 VCC = 3.3 V ± 0.3 V VCC = 5 V ± 0.5 V 10 20 ns/V 5 –40 • DALLAS, TEXAS 75265 mA 24 VCC = 4.5 V VCC = 1.8 V ± 0.15 V, 2.5 V ± 0.2 V POST OFFICE BOX 655303 mA –24 85 °C SN74LVC1GU04 SINGLE INVERTER SCES215B – APRIL 1999 – REVISED AUGUST 1999 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) TEST CONDITIONS VCC 1.65 V to 5.5 V IOH = –100 mA IOH = –4 mA 1.65 V VCC–0.1 1.2 2.3 V 1.9 2.7 V 2.2 IOH = –24 mA 3V 2.3 IOH = –32 mA IOL = 100 mA 4.5 V 3.8 IOH = –8 mA IOH = –12 mA VOH VOL 0.1 0.45 2.3 V 0.3 IOL = 12 mA 2.7 V 0.4 IOL = 24 mA 3V 0.55 4.5 V 0.55 V ±5 mA ±10 mA 1.65 V to 5.5 V 10 mA 2.7 V to 5.5 V 500 mA 0 to 5.5 V 0 IO = 0 UNIT V 1.65 V One input at VCC – 0.6 V, Other inputs at VCC or GND ∆ICC MAX 1.65 V to 5.5 V VI or VO = 5.5 V VI = 5.5 V or GND, ICC TYP† IOL = 4 mA IOL = 8 mA IOL = 32 mA VI = 5.5 V or GND II Ioff MIN Ci VI = VCC or GND † All typical values are at VCC = 3.3 V, TA = 25°C. 3.3 V pF switching characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figures 1 through 4) PARAMETER tpd FROM (INPUT) TO (OUTPUT) A Y VCC = 1.8 V ± 0.15 V MIN MAX VCC = 2.5 V ± 0.2 V MIN MAX VCC = 2.7 V MIN MAX VCC = 3.3 V ± 0.3 V MIN MAX VCC = 5 V ± 0.5 V MIN UNIT MAX ns operating characteristics, TA = 25°C PARAMETER Cpd Power dissipation capacitance TEST CONDITIONS VCC = 1.8 V TYP VCC = 2.5 V TYP f = 10 MHz POST OFFICE BOX 655303 VCC = 3.3 V TYP VCC = 5 V TYP UNIT pF • DALLAS, TEXAS 75265 3 PRODUCT PREVIEW PARAMETER SN74LVC1GU04 SINGLE INVERTER SCES215B – APRIL 1999 – REVISED AUGUST 1999 PARAMETER MEASUREMENT INFORMATION VCC = 1.8 V ± 0.15 V 2 × VCC S1 1 kΩ From Output Under Test Open GND CL = 30 pF (see Note A) 1 kΩ TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 2 × VCC GND LOAD CIRCUIT tw VCC Timing Input VCC/2 VOLTAGE WAVEFORMS PULSE DURATION th VCC Data Input VCC/2 VCC/2 0V VCC/2 VCC/2 0V tPLH tPLZ VCC VCC/2 tPZH VOH VCC/2 VOL VCC/2 0V Output Waveform 1 S1 at 2 × VCC (see Note B) tPHL VCC/2 VCC/2 tPZL VCC Input VCC Output Control VOLTAGE WAVEFORMS SETUP AND HOLD TIMES Output VCC/2 0V 0V tsu PRODUCT PREVIEW VCC VCC/2 Input Output Waveform 2 S1 at GND (see Note B) VOL + 0.15 V VOL tPHZ VCC/2 VOH VOH – 0.15 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2 ns, tf ≤ 2 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN74LVC1GU04 SINGLE INVERTER SCES215B – APRIL 1999 – REVISED AUGUST 1999 PARAMETER MEASUREMENT INFORMATION VCC = 2.5 V ± 0.2 V 2 × VCC S1 500 Ω From Output Under Test Open GND CL = 30 pF (see Note A) 500 Ω TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 2 × VCC GND LOAD CIRCUIT tw VCC VCC/2 0V 0V tsu VOLTAGE WAVEFORMS PULSE DURATION th VCC Data Input VCC/2 VCC/2 0V VCC/2 VCC/2 0V tPLH tPLZ VCC VCC/2 tPZH VOH VCC/2 VOL VCC/2 0V Output Waveform 1 S1 at 2 × VCC (see Note B) tPHL VCC/2 VCC/2 tPZL VCC Input VCC Output Control VOLTAGE WAVEFORMS SETUP AND HOLD TIMES Output VCC/2 PRODUCT PREVIEW Timing Input VCC VCC/2 Input Output Waveform 2 S1 at GND (see Note B) VOL + 0.15 V VOL tPHZ VCC/2 VOH VOH – 0.15 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2 ns, tf ≤ 2 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 2. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN74LVC1GU04 SINGLE INVERTER SCES215B – APRIL 1999 – REVISED AUGUST 1999 PARAMETER MEASUREMENT INFORMATION VCC = 2.7 V AND 3.3 V ± 0.3 V 6V S1 500 Ω From Output Under Test Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 6V GND LOAD CIRCUIT tw 2.7 V 2.7 V Timing Input PRODUCT PREVIEW Input 0V 0V VOLTAGE WAVEFORMS PULSE DURATION th 2.7 V Data Input 1.5 V 1.5 V 0V 1.5 V 1.5 V 0V tPLZ tPZL 2.7 V 1.5 V 2.7 V Output Control VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 1.5 V 0V tPLH Output 1.5 V 1.5 V tsu Input 1.5 V Output Waveform 1 S1 at 6 V (see Note B) 1.5 V VOH VOL Output Waveform 2 S1 at GND (see Note B) VOL + 0.3 V VOL tPHZ tPZH tPHL 1.5 V 3V 1.5 V 1.5 V VOH VOH – 0.3 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 3. Load Circuit and Voltage Waveforms 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN74LVC1GU04 SINGLE INVERTER SCES215B – APRIL 1999 – REVISED AUGUST 1999 PARAMETER MEASUREMENT INFORMATION VCC = 5 V ± 0.5 V S1 500 Ω From Output Under Test 11 V Open GND CL = 50 pF (see Note A) 500 Ω LOAD CIRCUIT TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 11 V GND VCC Timing Input VCC/2 0V tw tsu VCC VCC/2 0V VCC Data Input VCC/2 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VCC VCC/2 Input VCC/2 0V tPHL tPLH VOH VCC/2 Output VCC/2 VOL tPHL VCC/2 VCC Output Control Output Waveform 1 S1 at 11 V (see Note B) tPLH VCC/2 VCC/2 VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS VCC/2 0V tPLZ tPZL 5.5 V VCC/2 Output Waveform 2 S1 at GND (see Note B) VOL + 0.3 V VOL tPHZ tPZH VOH Output VCC/2 PRODUCT PREVIEW VCC/2 Input th VCC/2 VOH – 0.3 V VOH ≈0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 4. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1999, Texas Instruments Incorporated