TI TMS470R1B768

TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
16/32-Bit RISC Flash Microcontroller
FEATURES
1
• High-Performance Static CMOS Technology
• TMS470R1x 16/32-Bit RISC Core (ARM7TDM™)
– 60-MHz (Pipeline Mode)
– Independent 16/32-Bit Instruction Set
– Open Architecture With Third-Party Support
– Built-In Debug Module
– Utilizes Big-Endian Format
• Integrated Memory
– 768K-Byte Program Flash
– 3 Banks With 18 Contiguous Sectors
– Internal State Machine for Programming
and Erase
– 48K-Byte Static RAM (SRAM)
• 15 Dedicated GIO Pins, 1 Input-Only GIO Pin,
and 71 Additional Peripheral I/Os
• Operating Features
– Core Supply Voltage (VCC): 1.81–2.05 V
– I/O Supply Voltage (VCCIO): 3.0–3.6 V
– Low-Power Modes: STANDBY and HALT
– Extended Industrial Temperature Range
• 470+ System Module
– 32-Bit Address Space Decoding
– Bus Supervision for Memory and
Peripherals
– Analog Watchdog (AWD) Timer
– Real-Time Interrupt (RTI)
– System Integrity and Failure Detection
– Interrupt Expansion Module (IEM)
• Direct Memory Access (DMA) Controller
– 32 Control Packets and 16 Channels
• Zero-Pin Phase-Locked Loop (ZPLL)-Based
Clock Module With Prescaler
– Multiply-by-4 or -8 Internal ZPLL Option
– ZPLL Bypass Mode
•
23
•
•
•
•
•
•
•
(1)
Ten Communication Interfaces:
– Five Serial Peripheral Interfaces (SPIs)
– 255 Programmable Baud Rates
– Two Serial Communications Interfaces
(SCIs)
– 224 Selectable Baud Rates
– Asynchronous/Isosynchronous Modes
– Three High-End CAN Controllers (HECCs)
– 32-Mailbox Capacity Each
– Fully Compliant With CAN Protocol,
Version 2.0B
High-End Timer (HET)
– 32 Programmable I/O Channels:
– 24 High-Resolution Pins
– 8 Standard-Resolution Pins
– High-Resolution Share Feature (XOR)
– High-End Timer RAM
– 128-Instruction Capacity
16-Channel 10-Bit Multi-Buffered ADC
(MibADC)
– 256-Word FIFO Buffer
– Single- or Continuous-Conversion Modes
– 1.55-µs Minimum Sample and Conversion
Time
– Calibration Mode and Self-Test Features
Eight External Interrupts
Flexible Interrupt Handling
External Clock Prescale (ECP) Module
– Programmable Low-Frequency External
Clock (CLK)
On-Chip Scan-Base Emulation Logic, IEEE
Standard 1149.1(1) (JTAG) Test-Access Port
144-Pin Plastic Low-Profile Quad Flatpack
(PGE Suffix)
The test-access port is compatible with the IEEE Standard
1149.1-1990, IEEE Standard Test-Access Port and Boundary
Scan Architecture specification. Boundary scan is not
supported on this device.
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
ARM7TDM is a trademark of Advanced RISC Machines Limited (ARM).
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005–2008, Texas Instruments Incorporated
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
ADIN[0]
ADIN[1]
ADIN[2]
ADIN[3]
ADIN[4]
ADIN[15]
ADIN[5]
ADIN[6]
ADIN[7]
ADEVT
SPI3ENA
SPI3SCS
SPI3SIMO
SPI3SOMI
SPI3CLK
VCC
VSS
SCI1RX
SCI1TX
SCI1CLK
CAN1HTX
CAN1HRX
VCC
VSS
GIOB[7]
CLKOUT
VCCIO
VSSIO
HET[9]
HET[8]
CAN3HTX
CAN3HRX
TCK
TDO
TDI
PLLDIS
TMS470R1B768 144-Pin PGE Package (Top View)
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
AWD
HET[18]
HET[19]
HET[20]
HET[21]
HET[22]
SPI2SCS
SPI2ENA
SPI2SOMI
SPI2SIMO
SPI2CLK
SPI5ENA
SPI5CLK
SPI5SOMI
SPI5SIMO
CAN2HRX
CAN2HTX
VCC
VSS
VCCIO
VSSIO
HET[24]
HET[31]
HET[30]
HET[29]
HET[28]
SPI5SCS
SCI2CLK
SCI2TX
SCI2RX
GIOA[3]/INT3
GIOA[2]/INT2
GIOA[1]/INT1/ECLK
GIOA[0]/INT0(A)
TEST
TRST
SPI1ENA
SPI1SCS
SPI1SIMO
SPI1SOMI
SPI1CLK
SPI4ENA
SPI4SCS
SPI4SIMO
SPI4SOMI
SPI4CLK
VSS
OSCOUT
OSCIN
VCC
RST
VSSIO
VCCIO
GIOD[3]
GIOD[2]
GIOD[1]
GIOD[0]
HET[17]
HET[16]
HET[15]
HET[14]
HET[13]
HET[12]
HET[11]
HET[10]
VSS
VCC
PORRST
GIOA[7]/INT7
GIOA[6]/INT6
GIOA[5]/INT5
GIOA[4]/INT4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
ADIN[11]
ADIN[14]
ADIN[10]
ADIN[13]
ADIN[9]
ADIN[12]
ADIN[8]
ADREFHI
ADREFLO
VCCAD
VSSAD
TMS
TMS2
GIOC[0]
HET[23]
HET[25]
HET[26]
HET[27]
VSS
VCC
HET[0]
HET[1]
VSS
VCC
FLTP2
FLTP1
VCCP
VSS
HET[2]
HET[3]
HET[4]
HET[5]
HET[6]
HET[7]
GIOC[1]
GIOC[2]
A.
2
GIOA[0]/INT0 (pin 39) is an input-only GIO pin.
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
DESCRIPTION
The TMS470R1B768 (1) device is a member of the Texas Instruments (TI) TMS470R1x family of general-purpose
16/32-bit reduced instruction set computer (RISC) microcontrollers. The B768 microcontroller offers high
performance utilizing the high-speed ARM7TDMI 16/32-bit RISC central processing unit (CPU), resulting in a
high instruction throughput while maintaining greater code efficiency. The ARM7TDMI 16/32-bit RISC CPU views
memory as a linear collection of bytes numbered upwards from zero. The TMS470R1B768 utilizes the big-endian
format where the most significant byte of a word is stored at the lowest numbered byte and the least significant
byte at the highest numbered byte.
High-end embedded control applications demand more performance from their controllers while maintaining low
costs. The B768 RISC core architecture offers solutions to these performance and cost demands while
maintaining low power consumption.
The B768 device contains the following:
• ARM7TDMI 16/32-Bit RISC CPU
• TMS470R1x system module (SYS) with 470+ enhancements [including an interrupt expansion module (IEM)
and a 16-channel direct-memory access (DMA) controller]
• 768K-byte flash
• 48K-byte SRAM
• Zero-pin phase-locked loop (ZPLL) clock module
• Analog watchdog (AWD) timer
• Real-time interrupt (RTI) module
• Five serial peripheral interface (SPI) modules
• Two serial communications interface (SCI) modules
• Three high-end CAN controller (HECC) modules
• 10-bit multi-buffered analog-to-digital converter (MibADC) with 16 input channels
• High-end timer (HET) controlling 32 I/Os
• External clock prescale (ECP) module
• Up to 86 I/O pins and 1 input-only pin
The functions performed by the 470+ system module (SYS) include:
• Address decoding
• Memory protection
• Memory and peripherals bus supervision
• Reset and abort exception management
• Expanded interrupt capability with prioritization for all internal interrupt sources
• Device clock control
• Direct-memory access (DMA) and control
• Parallel signature analysis (PSA)
This data sheet includes device-specific information such as memory and peripheral select assignment, interrupt
priority, and a device memory map. For a more detailed functional description of the SYS module, see the
TMS470R1x System Module Reference Guide (literature number SPNU189). For a more detailed functional
description of the IEM module, see the TMS470R1x Interrupt Expansion Module (IEM) Reference Guide
(literature number SPNU211). And for a more detailed functional description of the DMA module, see the
TMS470R1x Direct-Memory Access (DMA) Controller Reference Guide (literature number SPNU210).
The B768 memory includes general-purpose SRAM supporting single-cycle read/write accesses in byte,
half-word, and word modes.
The flash memory on this device is a nonvolatile, electrically erasable and programmable memory implemented
with a 32-bit-wide data bus interface. The flash operates with a system clock frequency of up to 24 MHz. When
in pipeline mode, the flash operates with a system clock frequency of up to 60 MHz. For more detailed
information on the F05 devices flash, see the F05 flash section of this data sheet.
(1)
Throughout the remainder of this document, TMS470R1B768 shall be referred to as either the full device name or B768.
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
3
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
The B768 device has ten communication interfaces: five SPIs, two SCIs, and three HECCs. The SPI provides a
convenient method of serial interaction for high-speed communications between similar shift-register type
devices. The SCI is a full-duplex, serial I/O interface intended for asynchronous communication between the
CPU and other peripherals using the standard non-return-to-zero (NRZ) format. The HECC uses a serial,
multimaster communication protocol that efficiently supports distributed real-time control with robust
communication rates of up to 1 megabit per second (Mbps). The HECC is ideal for applications operating in
noisy and harsh environments (e.g., industrial fields) that require reliable serial communication or multiplexed
wiring. For more detailed functional information on the SPI, SCI, and HECC, see the specific reference guides for
these modules (literature numbers SPNU195, SPNU196, and SPNU197, respectively).
The HET is an advanced intelligent timer that provides sophisticated timing functions for real-time applications.
The timer is software controlled, using a reduced instruction set, with a specialized timer micromachine and an
attached I/O port. The HET can be used for compare, capture, or general-purpose I/O. It is especially well suited
for applications requiring multiple sensor information and drive actuators with complex and accurate time pulses.
For more detailed functional information on the HET, see the TMS470R1x High-End Timer (HET) Reference
Guide (literature number SPNU199).
The B768 HET peripheral contains the XOR-share feature. This feature allows two adjacent HET high-resolution
channels to be XORed together, making it possible to output smaller pulses than a standard HET. For more
detailed information on the HET XOR-share feature, see the TMS470R1x High-End Timer (HET) Reference
Guide (literature number SPNU199).
The B768 device has a 10-bit-resolution, 16-channel sample-and-hold MibADC. The MibADC channels can be
converted individually or can be grouped by software for sequential conversion sequences. There are three
separate groupings, two of which are triggerable by an external event. Each sequence can be converted once
when triggered or configured for continuous conversion mode. For more detailed functional information on the
MibADC, see the TMS470R1x Multi-Buffered Analog-to-Digital Converter (MibADC) Reference Guide (literature
number SPNU206).
The zero-pin phase-locked loop (ZPLL) clock module contains a phase-locked loop, a clock-monitor circuit, a
clock-enable circuit, and a prescaler (with prescale values of 1–8). The function of the ZPLL is to multiply the
external frequency reference to a higher frequency for internal use. The ZPLL provides ACLK to the system
(SYS) module. The SYS module subsequently provides system clock (SYSCLK), real-time interrupt clock
(RTICLK), CPU clock (MCLK), and peripheral interface clock (ICLK) to all other B768 device modules. For more
detailed functional information on the ZPLL, see the TMS470R1x Zero-Pin Phase-Locked Loop (ZPLL) Clock
Module Reference Guide (literature number SPNU212).
NOTE:
ACLK should not be confused with the MibADC internal clock, ADCLK. ACLK is the
continuous system clock from an external resonator/crystal reference.
The B768 device also has an external clock prescaler (ECP) module that when enabled, outputs a continuous
external clock (ECLK) on a specified GIO pin. The ECLK frequency is a user-programmable ratio of the
peripheral interface clock (ICLK) frequency. For more detailed functional information on the ECP, see the
TMS470R1x External Clock Prescaler (ECP) Reference Guide (literature number SPNU202).
4
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
Device Characteristics
Table 1 identifies all the characteristics of the TMS470R1B768 device except the SYSTEM and CPU, which are
generic.
Table 1. Device Characteristics
CHARACTERISTICS
DEVICE DESCRIPTION
TMS470R1B768
COMMENTS For B768
MEMORY
For the number of memory selects on this device, see Table 3, Memory Selection Assignment.
INTERNAL MEMORY
Pipeline/non-pipeline
768K-byte flash
48K-byte SRAM
Flash is pipeline-capable.
The B768 RAM is implemented in one 48K array selected by two
memory-select signals (see Table 3, Memory Selection Assignment).
PERIPHERALS
For the device-specific interrupt priority configurations, see Table 7, Interrupt Priority (IEM and CIM). And for the 1K peripheral address
ranges and their peripheral selects, see Table 5, B768 Peripherals, System Module, and Flash Base Addresses.
CLOCK
ZPLL
GENERAL-PURPOSE I/Os
15 I/O
1 input only
Zero-pin PLL has no external loop filter pins.
Port A has eight (8) external pins, port B has one (1), port C has
three (3), and port D has four (4).
ECP
YES
SCI
2 (3 pin)
SCI1 and SCI2
CAN (HECC and/or SCC)
3 HECCs
Three HECCs (HECC1, HECC2, and HECC3)
SPI (5-pin, 4-pin or 3-pin)
5 (5 pin)
SPI1, SPI2, SPI3, SPI4, and SPI5
HET with XOR Share
32 I/O
HET RAM
128-instruction capacity
MibADC
10-bit, 16-channel, 256-word
FIFO
CORE VOLTAGE
1.81V to 2.05 V
I/O VOLTAGE
3.0 V to 3.6 V
PINS
144
PACKAGE
PGE
The B768 device has both the logic and registers for a full 32-I/O
HET implemented and all 32 pins are available externally.
The high-resolution (HR) SHARE feature allows even HR pins to
share the next higher odd HR pin structures. This HR sharing is
independent of whether or not the odd pin is available externally. If
an odd pin is available externally and shared, then the odd pin can
only be used as a general-purpose I/O. For more information on HR
SHARE, see the TMS470R1x High-End Timer (HET) Reference
Guide (literature number SPNU199).
The B768 device has both the logic and registers for a full
16-channel MibADC implemented and all 16 pins are available
externally.
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
5
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
Functional Block Diagram
External Pins
ZPLL
VCCP
FLASH
(768K Bytes)
18 Sectors
FLTP1
FLTP2
RAM
(48K Bytes)
CPU Address/Data Bus
TMS470R1x
CPU
Expansion Address/Data Bus
TRST
TCK
TDI
TDO
TMS
TMS2
RST
AWD
TEST
PORRST
CLKOUT
TMS470R1x System Module
Interrupt
Expansion
Module (IEM)
DMA Controller
16 Channels
SPI4
SPI3
SPI2
MibADC
with
256−Word
FIFO
ADIN[15:0]
ADEVT
ADREFHI
ADREFLO
VCCAD
VSSAD
HET with
XOR Share
(128−Word)
HET [0:23]
HET[24:31]
HECC1
CAN1HTX
CAN1HRX
HECC2
CAN2HTX
CAN2HRX
HECC3
CAN3HTX
CAN3HRX
SCI1
SCI1CLK
SCI1TX
SCI1TX
SCI2
SCI2CLK
SCI2TX
SCI2TX
GIO
GIOD[0:3]
GIOC[0:2]
GIOB[7]
GIOA[2:7]/INT[2:7]
GIOA[0]/INT[0](A)
ECP
GIOA[1]/INT[1]/
ECLK
SPI1
SPI5SCS
SPI5ENA
SPI5SIMO
SPI5SOMI
SPI5CLK
SPI4SCS
SPI4ENA
SPI4SIMO
SPI4SOMI
SPI4CLK
SPI3SCS
SPI3ENA
SPI3SIMO
SPI3SOMI
SPI3CLK
SPI2SCS
SPI2ENA
SPI2SIMO
SPI2SOMI
SPI2CLK
SPI1SCS
SPI1ENA
SPI1SIMO
SPI1SOMI
SPI1CLK
SPI5
OSCIN
OSCOUT
PLLDIS
Crystal
External
Pins
A.
6
GIOA[0]/INT[0] is an input-only GIO pin.
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
Table 2. Terminal Functions
TERMINAL
NAME
NO.
TYPE (1) (2)
INTERNAL
PULLUP/
PULLDOWN (3)
DESCRIPTION
HIGH-END TIMER (HET)
HET[0]
129
HET[1]
130
HET[2]
137
HET[3]
138
HET[4]
139
HET[5]
140
HET[6]
141
HET[7]
142
HET[8]
79
HET[9]
80
HET[10]
29
HET[11]
28
HET[12]
27
HET[13]
26
HET[14]
25
HET[15]
24
HET[16]
23
HET[17]
22
HET[18]
71
HET[19]
70
HET[20]
69
HET[21]
68
HET[22]
67
HET[23]
123
HET[24]
51
HET[25]
124
HET[26]
125
HET[27]
126
HET[28]
47
HET[29]
48
HET[30]
49
HET[31]
50
CAN1HTX
CAN1HRX
3.3-V I/O
IPD (20 µA)
88
3.3-V I/O
IPU (20 µA)
87
3.3-V I/O
The B768 device has both the logic and registers for a full 32-I/O HET
implemented and all 32 pins are available externally.
Timer input capture or output compare. The HET[31:0] applicable pins can be
programmed as general-purpose input/output (GIO) pins. HET[23:0] are
high-resolution pins and HET[31:24] are standard-resolution pins.
The high-resolution (HR) SHARE feature allows even HR pins to share the
next higher odd-numbered HR pin structures. This HR sharing is independent
of whether or not the odd pin is available externally. If an odd pin is available
externally and shared, then the odd pin can only be used as a
general-purpose I/O. For more information on HR SHARE, see the
TMS470R1x High-End Timer (HET) Reference Guide (literature number
SPNU199).
HIGH-END CAN CONTROLLER 1 (HECC1)
HECC1 transmit pin or GIO pin
HECC1 receive pin or GIO pin
HIGH-END CAN CONTROLLER 2 (HECC2)
CAN2HTX
56
3.3-V I/O
CAN2HRX
57
3.3-V I/O
CAN3HTX
78
3.3 V I/O
CAN3HRX
77
3.3 V I/O
IPU (20 µA)
HECC2 transmit pin or GIO pin
HECC2 receive pin or GIO pin
HIGH-END CAN CONTROLLER 3 (HECC3)
(1)
(2)
(3)
IPU (20 µA)
HECC3 transmit pin or GIO pin
HECC3 receive pin or GIO pin
I = input, O = output, PWR = power, GND = ground, REF = reference voltage, NC = no connect
All I/O pins, except RST , are configured as inputs while PORRST is low and immediately after PORRST goes high.
IPD = internal pulldown, IPU = internal pullup (all internal pullups and pulldowns are active on input pins, independent of the PORRST
state.)
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
7
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
Table 2. Terminal Functions (continued)
TERMINAL
NAME
NO.
TYPE (1) (2)
INTERNAL
PULLUP/
PULLDOWN (3)
DESCRIPTION
GENERAL-PURPOSE I/O (GIO)
GIOA[0]/INT0
39
GIOA[1]/INT1
/ECLK
40
GIOA[2]/INT2
41
GIOA[3]/INT3
42
GIOA[4]/INT4
36
GIOA[5]/INT5
35
GIOA[6]/INT6
34
GIOA[7]/INT7
33
GIOB[7]
84
GIOC[0]
122
GIOC[1]
143
GIOC[2]
144
GIOD[0]
21
GIOD[1]
20
GIOD[2]
19
GIOD[3]
18
ADEVT
99
ADIN[0]
108
ADIN[1]
107
ADIN[2]
106
ADIN[3]
105
ADIN[4]
104
ADIN[5]
102
ADIN[6]
101
ADIN[7]
100
ADIN[8]
115
ADIN[9]
113
ADIN[10]
111
3.3-V I
3.3-V I/O
IPD (20 µA)
General-purpose input/output pins.
GIOA[0]/INT0 is an input-only pin. GIOA[7:0]/INT[7:0] are interrupt-capable
pins.
The GIOA[1]/INT1/ECLK pin is multiplexed with the external clock-out function
of the external clock prescale (ECP) module.
MULTI-BUFFERED ANALOG-TO-DIGITAL CONVERTER (MibADC)
8
3.3-V I/O
3.3-V I
IPD (20 µA)
MibADC event input. ADEVT can be programmed as a GIO pin.
MibADC analog input pins
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
Table 2. Terminal Functions (continued)
TERMINAL
NAME
NO.
TYPE (1) (2)
INTERNAL
PULLUP/
PULLDOWN (3)
DESCRIPTION
MULTI-BUFFERED ANALOG-TO-DIGITAL CONVERTER (MibADC) (CONTINUED)
ADIN[11]
109
ADIN[12]
114
ADIN[13]
112
ADIN[14]
110
ADIN[15]
103
ADREFHI
3.3-V I
MibADC analog input pins
116
3.3-V
REF I
MibADC module high-voltage reference input
ADREFLO
117
GND
REF I
MibADC module low-voltage reference input
VCCAD
118
3.3-V
PWR
MibADC analog supply voltage
VSSAD
119
GND
MibADC analog ground reference
SERIAL PERIPHERAL INTERFACE 1 (SPI1)
SPI1CLK
5
SPI1ENA
1
SPI1SCS
2
SPI1SIMO
3
SPI1SOMI
4
SPI1 clock. SPI1CLK can be programmed as a GIO pin.
SPI1 chip enable. SPI1ENA can be programmed as a GIO pin.
3.3-V I/O
IPD (20 µA)
SPI1 slave chip select. SPI1SCS can be programmed as a GIO pin.
SPI1 data stream. Slave in/master out. Can be programmed as a GIO pin.
SPI1 data stream. Slave out/master in. Can be programmed as a GIO pin.
SERIAL PERIPHERAL INTERFACE 2 (SPI2)
SPI2CLK
62
SPI2 clock. SPI2CLK can be programmed as a GIO pin.
SPI2ENA
65
SPI2 chip enable. SPI2ENA can be programmed as a GIO pin.
SPI2SCS
66
SPI2SIMO
63
SPI2 data stream. Slave in/master out. Can be programmed as a GIO pin.
SPI2SOMI
64
SPI2 data stream. Slave out/master in. Can be programmed as a GIO pin.
SPI3CLK
94
SPI3 clock. SPI3CLK can be programmed as a GIO pin.
SPI3ENA
98
SPI3 chip enable. SPI3ENA can be programmed as a GIO pin.
SPI3SCS
97
SPI3SIMO
96
SPI3SOMI
95
3.3-V I/O
IPD (20 µA)
SPI2 slave chip select. SPI2SCS can be programmed as a GIO pin.
SERIAL PERIPHERAL INTERFACE 3 (SPI3)
3.3-V I/O
IPD (20 µA)
SPI3 slave chip select. SPI3SCS can be programmed as a GIO pin.
SPI3 data stream. Slave in/master out. Can be programmed as a GIO pin.
SP3 data stream. Slave out/master in. Can be programmed as a GIO pin.
SERIAL PERIPHERAL INTERFACE 4 (SPI4)
SPI4CLK
10
SPI4ENA
6
SPI4 clock. SPI4CLK can be programmed as a GIO pin.
SPI4SCS
7
SPI4SIMO
8
SPI4 data stream. Slave in/master out. Can be programmed as a GIO pin.
SPI4SOMI
9
SPI4 data stream. Slave out/master in. Can be programmed as a GIO pin.
SPI4 chip enable. SPI4ENA can be programmed as a GIO pin.
3.3-V I/O
IPD (20 µA)
SPI4 slave chip select. SPI4SCS can be programmed as a GIO pin.
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
9
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
Table 2. Terminal Functions (continued)
TERMINAL
NAME
NO.
TYPE (1) (2)
INTERNAL
PULLUP/
PULLDOWN (3)
DESCRIPTION
SERIAL PERIPHERAL INTERFACE 5 (SPI5)
SPI5CLK
60
SPI5ENA
61
SPI5SCS
46
SPI5SIMO
58
SPI5SOMI
59
SPI5 clock. SPI5CLK can be programmed as a GIO pin.
SPI5 chip enable. SPI5ENA can be programmed as a GIO pin.
3.3-V I/O
IPD (20 µA)
SPI5 slave chip select. SPI5SCS can be programmed as a GIO pin.
SPI5 data stream. Slave in/master out. Can be programmed as a GIO pin.
SPI5 data stream. Slave out/master in. Can be programmed as a GIO pin.
ZERO-PIN PHASE-LOCKED LOOP (ZPLL)
OSCIN
13
1.8-V I
Crystal connection pin or external clock input
OSCOUT
12
1.8-V O
External crystal connection pin
PLLDIS
73
3.3-V I
SCI1CLK
89
3.3-V I/O
IPD (20 µA)
SCI1 clock. SCI1CLK can be programmed as a GIO pin.
SCI1RX
91
3.3-V I/O
IPU (20 µA)
SCI1 data receive. SCI1RX can be programmed as a GIO pin.
SCI1TX
90
3.3-V I/O
IPU (20 µA)
SCI1 data transmit. SCI1TX can be programmed as a GIO pin.
IPD (20 µA)
Enable/disable the ZPLL. The ZPLL can be bypassed and the oscillator
becomes the system clock. If not in bypass mode, TI recommends that this
pin be connected to ground or pulled down to ground by an external resistor.
SERIAL COMMUNICATIONS INTERFACE 1 (SCI1)
SERIAL COMMUNICATIONS INTERFACE 2 (SCI2)
SCI2CLK
45
3.3-V I/O
IPD (20 µA)
SCI2 clock. SCI2CLK can be programmed as a GIO pin.
SCI2RX
43
3.3-V I/O
IPU (20 µA)
SCI2 data receive. SCI2RX can be programmed as a GIO pin.
SCI2TX
44
3.3-V I/O
IPU (20 µA)
SCI2 data transmit. SCI2TX can be programmed as a GIO pin.
SYSTEM MODULE (SYS)
CLKOUT
83
3.3-V I/O
IPD (20 µA)
Bidirectional pin. CLKOUT can be programmed as a GIO pin or the output of
SYSCLK, ICLK, or MCLK.
PORRST
32
3.3-V I
IPD (20 µA)
Input master chip power-up reset. External VCC monitor circuitry must assert a
power-on reset.
IPU (20 µA)
Bidirectional reset. The internal circuitry can assert a reset, and an external
system reset can assert a device reset.
On this pin, the output buffer is implemented as an open drain (drives low
only). To ensure an external reset is not arbitrarily generated, TI recommends
that an external pullup resistor be connected to this pin.
RST
15
3.3-V I/O
WATCHDOG/REAL-TIME INTERRUPT (WD/RTI)
Analog watchdog reset. The AWD pin provides a system reset if the WD KEY
is not written in time by the system, providing an external RC network circuit
is connected. If the user is not using AWD, TI recommends that this pin be
connected to ground or pulled down to ground by an external resistor.
For more details on the external RC network circuit, see the TMS470R1x
System Module Reference Guide (literature number SPNU189) and the
application note Analog Watchdog Resistor, Capacitor and Discharge Interval
Selection Constraints (literature number SPNA005).
AWD
72
3.3-V I/O
IPD (20 µA)
TCK
76
3.3-V I
IPD (20 µA)
Test clock. TCK controls the test hardware (JTAG).
TDI
74
3.3-V I
IPU (20 µA)
Test data in. TDI inputs serial data to the test instruction register, test data
register, and programmable test address (JTAG).
TDO
75
3.3-V O
IPD (20 µA)
Test data out. TDO outputs serial data from the test instruction register, test
data register, identification register, and programmable test address (JTAG).
TEST/DEBUG (T/D)
10
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
Table 2. Terminal Functions (continued)
TERMINAL
NAME
NO.
TYPE (1) (2)
INTERNAL
PULLUP/
PULLDOWN (3)
DESCRIPTION
TEST/DEBUG (T/D) (CONTINUED)
TEST
38
3.3-V I
IPD (20 µA)
Test enable. Reserved for internal use only. TI recommends that this pin be
connected to ground or pulled down to ground by an external resistor.
TMS
120
3.3-V I
IPU (20 µA)
Serial input for controlling the state of the CPU test access port (TAP)
controller (JTAG)
TMS2
121
3.3-V I
IPU (20 µA)
Serial input for controlling the second TAP. TI recommends that this pin be
connected to VCCIO or pulled up to VCCIO by an external resistor.
TRST
37
3.3-V I
IPD (20 µA)
Test hardware reset to TAP1 and TAP2. IEEE Standard 1149-1 (JTAG)
Boundary-Scan Logic. TI recommends that this pin be pulled down to ground
by an external resistor.
FLASH
FLTP1
134
NC
Flash test pad 1. For proper operation, this pin must not be connected
[no connect (NC)].
FLTP2
133
NC
Flash test pad 2. For proper operation, this pin must not be connected
[no connect (NC)].
VCCP
135
3.3-V PWR
Flash external pump voltage (3.3 V). This pin is required for both flash read
and flash program and erase operations.
SUPPLY VOLTAGE CORE (1.8 V)
14
31
55
VCC
86
1.8-V PWR
Core logic supply voltage
93
128
132
SUPPLY VOLTAGE DIGITAL I/O (3.3 V)
17
VCCIO
53
3.3-V PWR
Digital I/O supply voltage
82
SUPPLY GROUND CORE
11
30
54
VSS
85
92
GND
Core supply ground reference
127
131
136
SUPPLY GROUND DIGITAL I/O
16
VSSIO
52
GND
Digital I/O supply ground reference
81
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
11
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
B768 DEVICE-SPECIFIC INFORMATION
Memory
Figure 1 shows the memory map of the B768 device.
Memory (4G Bytes)
0xFFFF_FFFF
0xFFF8_0000
0xFFF7_FFFF
SYSTEM with PSA, CIM,
RTI, DEC
System Module
Control Registers
(512K Bytes)
0xFFFF_FD00
IEM
Reserved
Peripheral Control Registers
(512K Bytes)
0xFFF0_0000
0xFFEF_FFFF
0xFFFF_FFFF
0xFFFF_FC00
0xFFF8_0000
HET
0xFFF7_FC00
Reserved
0xFFE8_C000
0xFFE8_BFFF
0xFFE8_8000
0xFFE8_7FFF
Flash Control Registers
0xFFE8_4024
0xFFE8_4023
0xFFE8_4000
0xFFE8_3FFF
MPU Control Registers
SPI1
0xFFF7_F800
SCI2
0xFFF7_F500
Reserved
SCI1
0xFFF7_F400
MibADC
0xFFF7_F000
Reserved
GIO/ECP
0xFFF7_EC00
0xFFE0_0000
HECC1/HECC2
0xFFF7_E800
HECC1/2 RAM
0xFFF7_E400
Reserved
0xFFF7_D800
SPI4/SPI5
0xFFF7_D600
RAM
(48K Bytes)
SPI2/SPI3
0xFFF7_D400
Program
and
Data Area
FLASH
(768K Bytes)
18 Sectors
HECC3 and HECC3 RAM
0xFFF7_D000
Reserved
0xFFF7_C000
Reserved
HET RAM
(1.5K Bytes)
0xFFF0_0000
FIQ
0x0000_001F
0x0000_001C
IRQ
0x0000_0018
Reserved
0x0000_0014
Data Abort
0x0000_0010
Prefetch Abort
0x0000_0020
0x0000_001F
0x0000_000C
Software Interrupt
Exception, Interrupt, and
Reset Vectors
0x0000_0008
Undefined Instruction
Reset
0x0000_0000
0x0000_0004
0x0000_0000
A.
Memory addresses are configurable by the system (SYS) module within the range of 0x0000_0000 to 0xFFE0_0000.
B.
The CPU registers are not part of the memory map.
Figure 1. TMS470R1B768 Memory Map
12
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
Memory Selects
Memory selects allow the user to address memory arrays (i.e., flash, RAM, and HET RAM) at user-defined
addresses. Each memory select has its own set (low and high) of memory base address registers (MFBAHRx
and MFBALRx) that, together, define the array's starting (base) address, block size, and protection.
The base address of each memory select is configurable to any memory address boundary that is a multiple of
the decoded block size. For more information on how to control and configure these memory select registers, see
the bus structure and memory sections of the TMS470R1x System Module Reference Guide (literature number
SPNU189).
For the memory selection assignments and the memory selected, see Table 3.
Table 3. Memory Selection Assignment
(1)
MEMORY
SELECT
MEMORY SELECTED
(ALL INTERNAL)
0 (fine)
FLASH
1 (fine)
FLASH
2 (fine)
RAM
3 (fine)
RAM
4 (fine)
HET RAM
MEMORY
SIZE
768K
48K (1)
MPU
MEMORY BASE ADDRESS
REGISTER
NO
MFBAHR0 and MFBALR0
NO
MFBAHR1 and MFBALR1
YES
MFBAHR2 and MFBALR2
YES
MFBAHR3 and MFBALR3
1.5K
STATIC MEM
CTL REGISTER
MFBAHR4 and MFBALR4
SMCR1
The starting addresses for both RAM memory-select signals cannot be offset from each other by a multiple of the user-defined block
size in the memory-base address register.
RAM
The B768 device contains 48K bytes of internal static RAM configurable by the SYS module to be addressed
within the range of 0x0000_0000 to 0xFFE0_0000. This B768 RAM is implemented in one 48K-byte array
selected by two memory-select signals. This B768 configuration imposes an additional constraint on the memory
map for RAM; the starting addresses for both RAM memory selects cannot be offset from each other by the
multiples of the size of the physical RAM (i.e., 48K bytes for the B768 device). The B768 RAM is addressed
through memory selects 2 and 3.
The RAM can be protected by the memory protection unit (MPU) portion of the SYS module, allowing the user
finer blocks of memory protection than is allowed by the memory selects. The MPU is ideal for protecting an
operating system while allowing access to the current task. For more detailed information on the MPU portion of
the SYS module and memory protection, see the memory section of the TMS470R1x System Module Reference
Guide (literature number SPNU189).
F05 Flash
The F05 flash memory is a nonvolatile electrically erasable and programmable memory implemented with a
32-bit-wide data bus interface. The F05 flash has an external state machine for program and erase functions.
See the flash read and flash program and erase sections below.
Flash Protection Keys
The B768 device provides flash protection keys. These four 32-bit protection keys prevent
program/erase/compaction operations from occurring until after the four protection keys have been matched by
the CPU loading the correct user keys into the FMPKEY control register. The protection keys on the B768 are
located in the last 4 words of the first 16K sector. For more detailed information on flash program and erase
operations, see the TMS470R1x F05 Flash Reference Guide (literature number SPNU213).
Flash Read
The B768 flash memory is configurable by the SYS module to be addressed within the range of 0x0000_0000 to
0xFFE0_0000. The flash is addressed through memory selects 0 and 1.
NOTE:
The flash external pump voltage (VCCP ) is required for all operations (program, erase,
and read).
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
13
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
Flash Pipeline Mode
When in pipeline mode, the flash operates with a system clock frequency of up to 60 MHz (versus a system
clock in normal mode of up to 30 MHz). Flash in pipeline mode is capable of accessing 64-bit words and
provides two 32-bit pipelined words to the CPU. Also in pipeline mode, the flash can be read with no wait states
when memory addresses are contiguous (after the initial 1-or 2-wait-state reads).
NOTE:
After a system reset, pipeline mode is disabled (ENPIPE bit [FMREGOPT.0] is a 0). In
other words, the B768 device powers up and comes out of reset in non-pipeline
mode. Furthermore, setting the flash configuration mode bit (GBLCTRL.4) will override
pipeline mode.
Flash Program and Erase
The B768 device flash contains three 256K-byte memory arrays (or banks) for a total of 768K bytes of flash and
consists of 18 sectors. These 18 sectors are sized as follows:
Table 4. B768 Flash Memory Banks and Sectors
SECTOR NO.
SEGMENT
LOW ADDRESS
HIGH ADDRESS
0
16K Bytes
0x0000_0000
0x0000_3FFF
1
16K Bytes
0x0000_4000
0x0000_7FFF
2
32K Bytes
0x0000_8000
0x0000_FFFF
3
32K Bytes
0x0001_0000
0x0001_7FFF
4
32K Bytes
0x0001_8000
0x0001_FFFF
5
32K Bytes
0x0002_0000
0x0002_7FFF
6
32K Bytes
0x0002_8000
0x0002_FFFF
7
32K Bytes
0x0003_0000
0x0003_7FFF
8
16K Bytes
0x0003_8000
0x0003_BFFF
9
16K Bytes
0x0003_C000
0x0003_FFFF
0
64K Bytes
0x0004_0000
0x0004_FFFF
1
64K Bytes
0x0005_0000
0x0005_FFFF
2
64K Bytes
0x0006_0000
0x0006_FFFF
3
64K Bytes
0x0007_0000
0x0007_FFFF
0
64K Bytes
0x0008_0000
0x0008_FFFF
1
64K Bytes
0x0009_0000
0x0009_FFFF
2
64K Bytes
0x000A_0000
0x000A_FFFF
3
64K Bytes
0x000B_0000
0x000B_FFFF
MEMORY ARRAYS
(OR BANKS)
BANK0
(256K Bytes)
BANK1
(256K Bytes)
BANK2
(256K Bytes)
The minimum size for an erase operation is one sector. The maximum size for a program operation is one 16-bit
word. For more detailed information on flash program and erase operations, see the TMS470R1x Flash
Reference Guide (literature number SPNU194).
NOTE:
The flash external pump voltage (VCCP ) is required for all operations (program, erase,
and read).
HET RAM
The B768 device contains HET RAM. The HET RAM has a 128-instruction capability. The HET RAM is
configurable by the SYS module to be addressed within the range of 0x0000_0000 to 0xFFE0_0000. The HET
RAM is addressed through memory select 4.
14
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
Peripheral Selects and Base Addresses
The B768 device uses 8 of the 16 peripheral selects to decode the base addresses of the peripherals. These
peripheral selects are fixed and transparent to the user since they are part of the decoding scheme used by the
SYS module.
Control registers for the peripherals, SYS module, and flash begin at the base addresses shown in Table 5.
Table 5. B768 Peripherals, System Module, and Flash Base Addresses
CONNECTING MODULE
ADDRESS RANGE
PERIPHERAL SELECTS
BASE ADDRESS
ENDING ADDRESS
SYSTEM
0 x FFFF_FFD0
0 x FFFF_FFFF
N/A
RESERVED
0 x FFFF_FF60
0 x FFFF_FFCB
N/A
PSA
0 x FFFF_FF40
0 x FFFF_FF5F
N/A
CIM
0 x FFFF_FF20
0 x FFFF_FF3F
N/A
RTI
0 x FFFF_FF00
0 x FFFF_FF1F
N/A
DMA
0 x FFFF_FE80
0 x FFFF_FEFF
N/A
DEC
0 x FFFF_FE00
0 x FFFF_FE7F
N/A
MMC
0 x FFFF_FD00
0 x FFFF_FD7F
N/A
IEM
0 x FFFF_FC00
0 x FFFF_FCFF
N/A
RESERVED
0 x FFF8_0000
0 x FFFF_FBFF
N/A
RESERVED
0 x FFF7_FD00
0 x FFF7_FFFF
HET
0 x FFF7_FC00
0 x FFF7_FCFF
RESERVED
0 x FFF7_F900
0 x FFF7_FBFF
SPI1
0 x FFF7_F800
0 x FFF7_F8FF
RESERVED
0 x FFF7_F600
0 x FFF7_F7FF
SCI2
0 x FFF7_F500
0 X FFF7_F5FF
SCI1
0 x FFF7_F400
0 x FFF7_F4FF
RESERVED
0 x FFF7_F100
0 x FFF7_F3FF
MibADC
0 x FFF7_F000
0 x FFF7_F0FF
ECP
0 x FFF7_EF00
0 x FFF7_EFFF
RESERVED
0 x FFF7_ED00
0 x FFF7_EEFF
GIO
0 x FFF7_EC00
0 x FFF7_ECFF
HECC2
0 x FFF7_EA00
0 x FFF7_EBFF
HECC1
0 x FFF7_E800
0 x FFF7_E9FF
HECC2 RAM
0 x FFF7_E600
0 x FFF7_E7FF
HECC1 RAM
0 x FFF7_E400
0 x FFF7_E5FF
PS[0]
PS[1]
PS[2]
PS[3]
PS[4]
PS[5]
PS[6]
RESERVED
0 x FFF7_E000
0 x FFF7_E3FF
PS[7]
RESERVED
0 x FFF7_DC00
0 x FFF7_DFFF
PS[8]
RESERVED
0 x FFF7_D800
0 x FFF7_DBFF
PS[9]
SPI5
0 x FFF7_D700
0 x FFF7_D7FF
SPI4
0 x FFF7_D600
0 x FFF7_D6FF
SPI3
0 x FFF7_D500
0 x FFF7_D5FF
PS[10]
SPI2
0 x FFF7_D400
0 x FFF7_D4FF
HECC3 RAM
0 x FFF7_D200
0 x FFF7_D3FF
HECC3
0 x FFF7_D000
0 x FFF7_D1FF
RESERVED
0 x FFF7_C000
0 x FFF7_CFFF
PS[12]–PS[15]
RESERVED
0 x FFF7_0000
0 x FFF7_BFFF
N/A
FLASH CONTROL REGISTERS
0 x FFE8_8000
0 x FFE8_BFFF
N/A
MPU CONTROL REGISTERS
0 x FFE8_4000
0 x FFE8_4023
N/A
PS[11]
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
15
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
Direct-Memory Access (DMA)
The direct-memory access (DMA) controller transfers data to and from any specified location in the B768
memory map (except for restricted memory locations like the system control registers area). The DMA manages
up to 16 channels, and supports data transfer for both on-chip and off-chip memories and peripherals. The DMA
controller is connected to both the CPU and Peripheral busses, enabling these data transfers to occur in parallel
with CPU activity and thus maximizing overall system performance.
Although the DMA controller has two possible configurations, for the B768 device, the DMA controller
configuration is 32 control packets and 16 channels.
For the B768 DMA request hardwired configuration, see Table 6.
Table 6. DMA Request Lines Connections
MODULES
DMA REQUEST INTERRUPT SOURCES
RESERVED
DMAREQ[0]
SPI1
SPI1 end-receive
SPI1DMA0
DMAREQ[1]
SPI1
SPI1 end-transmit
SPI1DMA1
DMAREQ[2]
MibADC
(1)
MibADC event
MibADCDMA0
DMAREQ[3]
MibADC (1)/SCI1
MibADC G1/SCI1 end-receive
MibADCDMA1/SCI1DMA0
DMAREQ[4]
MibADC (1)/SCI1
MibADC G2/SCI1 end-transmit
MibADCDMA2/SCI1DMA1
DMAREQ[5]
SPI4
SPI4 end-receive
SPI4DMA0
DMAREQ[6]
SPI2
SPI2 end-receive
SPI2DMA0
DMAREQ[7]
SPI2
SPI2 end-transmit
SPI2DMA1
DMAREQ[8]
RESERVED
DMAREQ[9]
RESERVED
(1)
DMA CHANNEL
DMAREQ[10]
SPI4
SPI4 end-transmit
SPI4DMA1
DMAREQ[11]
SPI5
SPI5 end-receive
SPI5DMA0
DMAREQ[12]
SPI5
SPI5 end-transmit
SPI5DMA1
DMAREQ[13]
SCI2/SPI3
SCI2 end-receive/SPI3 end-receive
SCI2DMA0/SPI3DMA0
DMAREQ[14]
SCI2/SPI3
SCI2 end-transmit/SPI3 end-transmit
SCI2DMA1/SPI3DMA1
DMAREQ[15]
The MibADC can be serviced by the DMA when the device is in buffered mode. For more information on buffered mode, see the
MibADC section of this data sheet and the TMS470R1x Multi-Buffered Analog-to-Digital Converter (MibADC) Reference Guide (literature
number SPNU206).
Each channel has two control packets attached to it, allowing the DMA to continuously load RAM and generate
periodic interrupts so that the data can be read by the CPU. The control packets allow for the interrupt enable,
and the channels determine the priority level of the interrupt.
DMA transfers occur in one of two modes:
• Non-request mode (used when transferring from memory to memory)
• Request mode (used when transferring from memory to peripheral)
For more detailed functional information on the DMA controller, see the TMS470R1x Direct Memory Access
(DMA) Controller Reference Guide (literature number SPNU210).
16
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
Interrupt Priority (IEM to CIM)
Interrupt requests originating from the B768 peripheral modules (i.e., SPI1, SPI2, or SPI3; SCI1 or SCI2; HECC1
or HECC2; RTI; etc.) are assigned to channels within the 48-channel interrupt expansion module (IEM) where,
via programmable register mapping, these channels are then mapped to the 32-channel central interrupt
manager (CIM) portion of the SYS module.
Programming multiple interrupt sources in the IEM to the same CIM channel effectively shares the CIM channel
between sources.
The CIM request channels are maskable so that individual channels can be selectively disabled. All interrupt
requests can be programmed in the CIM to be of either type:
• Fast interrupt request (FIQ)
• Normal interrupt request (IRQ)
The CIM prioritizes interrupts. The precedence of request channels decrease with ascending channel order in the
CIM (0 [highest] and 31 [lowest] priority). For IEM-to-CIM default mapping, channel priorities, and their
associated modules, see Table 7.
Table 7. Interrupt Priority (IEM and CIM)
MODULES
INTERRUPT SOURCES
DEFAULT CIM INTERRUPT
LEVEL/CHANNEL
IEM CHANNEL
SPI1
SPI1 end-transfer/overrun
0
0
RTI
COMP2 interrupt
1
1
RTI
COMP1 interrupt
2
2
RTI
TAP interrupt
3
3
SPI2
SPI2 end-transfer/overrun
4
4
GIO
GIO interrupt A
5
5
6
6
RESERVED
HET
HET interrupt 1
7
7
SPI4
SPI4 end-transfer/overrun
8
8
SCI1 or SCI2 error interrupt
9
9
SCI1 receive interrupt
10
10
SCI1/SCI2
SCI1
RESERVED
11
11
SPI5 end-transfer/overrun
12
12
HECC1 interrupt A
13
13
14
14
SPI3 end-transfer/overrun
15
15
MibADC end event conversion
16
16
SCI2
SCI2 receive interrupt
17
17
DMA
DMA interrupt 0
18
18
HECC3 interrupt A
19
19
SCI1 transmit interrupt
20
20
SW interrupt (SSI)
21
21
22
22
HET interrupt 2
23
23
HECC1 interrupt B
24
24
SPI5
HECC1
RESERVED
SPI3
MibADC
HECC3
SCI1
System
RESERVED
HET
HECC1
RESERVED
25
25
SCI2 transmit interrupt
26
26
MibADC end Group 1 conversion
27
27
DMA
DMA interrupt 1
28
28
GIO
GIO interrupt B
29
29
MibADC
MibADC end Group 2 conversion
30
30
HECC3
HECC3 interrupt B
31
31
SCI2
MibADC
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
17
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
Table 7. Interrupt Priority (IEM and CIM) (continued)
DEFAULT CIM INTERRUPT
LEVEL/CHANNEL
IEM CHANNEL
RESERVED
31
32
RESERVED
31
33
RESERVED
31
34
RESERVED
31
35
RESERVED
31
36
MODULES
INTERRUPT SOURCES
RESERVED
31
37
HECC2
HECC2 interrupt A
31
38
HECC2
HECC2 interrupt B
31
39
RESERVED
31
40
RESERVED
31
41
RESERVED
31
42
RESERVED
31
43
RESERVED
31
44
RESERVED
31
45
RESERVED
31
46
RESERVED
31
47
For more detailed functional information on the IEM, see the TMS470R1x Interrupt Expansion Module (IEM)
Reference Guide (literature number SPNU211). For more detailed functional information on the CIM, see the
TMS470R1x System Module Reference Guide (literature number SPNU189).
18
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
MibADC
The multi-buffered analog-to-digital converter (MibADC) accepts an analog signal and converts the signal to a
10-bit digital value.
The B768 MibADC module can function in two modes: compatibility mode, where its programmer's model is
compatible with the TMS470R1x ADC module and its digital results are stored in digital result registers; or in
buffered mode, where the digital result registers are replaced with three FIFO buffers, one for each conversion
group [event, group1 (G1), and group2 (G2)]. In buffered mode, the MibADC buffers can be serviced by
interrupts or by the DMA.
MibADC Event Trigger Enhancements
The MibADC includes two major enhancements over the event-triggering capability of the TMS470R1x ADC.
• Both group1 and the event group can be configured for event-triggered operation, providing up to two
event-triggered groups.
• The trigger source and polarity can be selected individually for both group 1 and the event group from the
three options identified in Table 8.
Table 8. MibADC Event Hookup Configuration
EVENT #
SOURCE SELECT BITS FOR G1 OR
EVENT(G1SRC[1:0] OR EVSRC[1:0])
SIGNAL PIN NAME
EVENT1
00
ADEVT
EVENT2
01
HET18
EVENT3
10
HET19
EVENT4
11
N/C
For group 1, these event-triggered selections are configured via the group 1 source select bits (G1SRC[1:0]) in
the AD event source register (ADEVTSRC[5:4]). For the event group, these event-triggered selections are
configured via the event group source select bits (EVSRC[1:0]) in the AD event source register
(ADEVTSRC[1:0]).
For more detailed functional information on the MibADC, see the TMS470R1x Multi-Buffered Analog-to-Digital
Converter (MibADC) Reference Guide (literature number SPNU206).
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
19
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
Documentation Support
Extensive documentation supports all of the TMS470 microcontroller family generation of devices. The types of
documentation available include data sheets with design specifications; complete user guides for all devices and
development support tools; and hardware and software applications. Useful reference documentation includes:
• Bulletin
– TMS470 Microcontroller Family Product Bulletin (literature number SPNB086)
• User's Guides
– TMS470R1x System Module Reference Guide (literature number SPNU189)
– TMS470R1x General Purpose Input/Output (GIO) Reference Guide (literature number SPNU192)
– TMS470R1x Direct Memory Access (DMA) Controller Reference Guide (literature number SPNU194)
– TMS470R1x Serial Peripheral Interface (SPI) Reference Guide (literature number SPNU195)
– TMS470R1x Serial Communication Interface (SCI) Reference Guide (literature number SPNU196)
– TMS470R1x Controller Area Network (CAN) Reference Guide (literature number SPNU197)
– TMS470R1x High End Timer (HET) Reference Guide (literature number SPNU199)
– TMS470R1x External Clock Prescale (ECP) Reference Guide (literature number SPNU202)
– TMS470R1x MultiBuffered Analog to Digital (MibADC) Reference Guide (literature number SPNU206)
– TMS470R1x Zero-Pin Phase Locked Loop (ZPLL) Clock Module Reference Guide (literature number
SPNU212)
– TMS470R1x F05 Flash Reference Guide (literature number SPNU213)
– TMS470R1x Class II Serial Interface B (C2SIb) Reference Guide (literature number SPNU214)
– TMS470R1x Class II Serial Interface A (C2SIa) Reference Guide (literature number SPNU218)
– TMS470R1x JTAG Security Module (JSM) Reference Guide (literature number SPNU245)
– TMS470R1x Memory Security Module (MSM) Reference Guide (literature number SPNU246)
– TMS470 Peripherals Overview Reference Guide (literature number SPNU248)
• Errata Sheet
– TMS470R1B768 TMS470 Microcontrollers Silicon Errata (literature number SPNZ140)
20
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
Device and Development-Support Tool Nomenclature
To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all DSP
devices and support tools. Each DSP commercial family member has one of three prefixes: TMX, TMP, or TMS
(e.g., TMS470R1B768). Texas Instruments recommends two of three possible prefix designators for its support
tools: TMDX and TMDS. These prefixes represent evolutionary stages of product development from engineering
prototypes (TMX/TMDX) through fully qualified production devices/tools (TMS/TMDS).
Device development evolutionary flow:
TMX Experimental device that is not necessarily representative of the final device's electrical specifications
TMP Final silicon die that conforms to the device's electrical specifications but has not completed quality and
reliability verification
TMS Fully qualified production device
Support tool development evolutionary flow:
TMDX Development-support product that has not yet completed Texas Instruments internal qualification testing.
TMDS Fully qualified development-support product
TMX and TMP devices and TMDX development-support tools are shipped against the following disclaimer:
"Developmental product is intended for internal evaluation purposes."
TMS devices and TMDS development-support tools have been characterized fully, and the quality and reliability
of the device have been demonstrated fully. TI's standard warranty applies.
Predictions show that prototype devices (TMX or TMP) have a greater failure rate than the standard production
devices. Texas Instruments recommends that these devices not be used in any production system because their
expected end-use failure rate still is undefined. Only qualified production devices are to be used.
Figure 2 illustrates the numbering and symbol nomenclature for the TMS470R1x family.
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
21
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
TMS 470 R1 B
768
PGE
T
OPTIONS
PREFIX
TMS = Fully Qualified Device
FAMILY
470 = TMS470 RISC − Embedded
Microcontroller Family
TEMPERATURE RANGE
T = −40°C to 105°C
Q = −40°C to 125°C
PACKAGE TYPE
PGE = 144-pin Low-Profile Quad Flatpack (LQFP)
ARCHITECTURE
R1 = ARM7TDM1 CPU
DEVICE TYPE B
With 768K-Bytes Flash Memory:
60-MHz Frequency
1.8-V Core, 3.3-V I/O
Flash Program Memory
48K-Byte SRAM
ECP Module
Up to 68 I/O Pins and 1 Input-Only Pin
ZPLL Clock
1.5K-Byte HET RAM (128 Instructions)
AWD
RTI
10-Bit, 12-Input MibADC
Five SPI Modules
Two SCI Modules
Three High-End CAN [HECC] Modules
HET, 32 Channels
ECP
DMA
REVISION CHANGE
Blank = Original
FLASH MEMORY
768 = 768K-Bytes Flash Memory
Figure 2. TMS470R1x Family Nomenclature
22
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
Device Identification Code Register
The device identification code register identifies the silicon version, the technology family (TF), a ROM or flash
device, and an assigned device-specific part number (see Figure 3). The B768 device identification code register
value is 0xn87F.
Figure 3. TMS470 Device ID Bit Allocation Register [offset = 0xFFFF_FFF0h]
31
16
Reserved
15
12
VERSION
11
10
TF
R/F
9
3
2
1
0
PART NUMBER
1
1
1
R-K
R-1
R-1
R-1
R-K
R-K
R-K
LEGEND:
For bits 3-15: R = Read only, -K = Value constant after RST
For bits 0-2: R = Read only, -1 = Value after RST
Table 9. TMS470 Device ID Bit Allocation Register Field Descriptions
Bit
Field
Value
Description
31–16
Reserved
Reads are undefined and writes have no effect.
15–12
VERSION
Silicon version (revision) bits. These bits identify the silicon version of the device. Initial device
version numbers start at 0000. The current revision for the B768 device is 0000.
TF
Technology family bit. This bit distinguishes the technology family core power supply:
11
10
0
3.3 V for F10/C10 devices
1
1.8 V for F05/C05 devices
R/F
ROM/flash bit. This bit distinguishes between ROM and flash devices:
0
Flash device
1
ROM device
9–3
PART NUMBER
Device-specific part number bits. These bits identify the assigned device-specific part number. The
assigned device-specific part number for the B768 device is 0001111.
2–0
1
Mandatory high
Bits 2, 1, and 0 are tied high by default.
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
23
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
DEVICE ELECTRICAL SPECIFICATIONS AND TIMING PARAMETERS
Absolute Maximum Ratings
over operating free-air temperature range, T version unless otherwise noted (1)
VCC (2)
Supply voltage range:
–0.3 V to 2.5 V
Supply voltage range:
VCCIO , VCCAD , VCCP (flash pump)
Input voltage range:
All input pins
Input clamp current:
IIK (VI < 0 or VI > VCCIO )
(2)
–0.3 V to 4.1 V
–0.3 V to 4.1 V
All pins except ADIN[0:15], PORRST, TRST,
TEST, and TCK
±20 mA
IIK (VI < 0 or VI > VCCAD )
ADIN[0:15]
Operating free-air temperature range, TA:
±10 mA
T version
–40°C to 105°C
Q version
–40°C to 125°C
Operating junction temperature range, TJ:
–40°C to 150°C
Storage temperature range, Tstg:
–65°C to 150°C
(1)
(2)
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to their associated grounds.
Device Recommended Operating Conditions (1)
MIN
NOM
VCC
Digital logic supply voltage (core)
2.05
V
VCCIO
Digital logic supply voltage (I/O)
3
3.3
3.6
V
VCCAD
MibADC supply voltage
3
3.3
3.6
V
VCCP
Flash pump supply voltage
3
3.3
3.6
V
VSS
Digital logic supply ground
VSSAD
MibADC supply ground
TA
Operating free-air temperature
TJ
Operating junction temperature
(1)
24
1.81
MAX UNIT
0
V
–0.1
0.1
V
T version
–40
105
°C
Q version
–40
125
°C
–40
150
°C
All voltages are with respect to VSS , except VCCAD, which is with respect to VSSAD.
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
ELECTRICAL CHARACTERISTICS
over recommended operating free-air temperature range, T version (unless otherwise noted) (1)
PARAMETER
Vhys
TEST CONDITIONS
Input hysteresis
VIL
Low-level input voltage
VIH
High-level input voltage
–0.3
0.35 VCC
2
VCCIO + 0.3
0.65 VCC
VCC + 0.3
1.35
1.8
V
175
Ω
All inputs except
OSCIN
AWD only
RDSON
AWD only (3)
VOL
Low-level output voltage (4)
VOH
High-level output voltage (4)
IIC
Input clamp current (I/O pins) (5)
VOL = 0.35 V at IOL = 2 mA
IOL = IOL MAX
0.2 VCCIO
IOL = 50 µA
0.2
IOH = IOH MIN
0.8 VCCIO
IOH = 50 µA
VI < VSSIO – 0.3 or
VI > VCCIO + 0.3
–2
IIL Pulldown
VI = VSS
–1
1
IIH Pulldown
VI = VCCIO
5
40
IIL Pullup
VI = VSS
–40
–5
IIH Pullup
VI = VCCIO
–1
1
All other pins
No pullup or pulldown
–1
1
RST, SPInCLK,
SPInSOMI,
SPInSIMO (6)
(8)
µA
mA
–8
–4
VOH = VOH MIN
mA
–2
135
mA
SYSCLK = 24 MHz,
ICLK = 12 MHz, VCC = 2.05 V
105
mA
VCC Digital supply current (standby mode) (8)
OSCIN = 6 MHz, VCC = 2.05 V
4
mA
VCC Digital supply current (halt mode) (8)
All frequencies, VCC = 2.05 V
2
mA
VCCIO Digital supply current (operating mode)
No DC load, VCCIO = 3.6 V (8)
10
mA
VCCIO Digital supply current (standby mode)
No DC load, VCCIO = 3.6 V
(8)
300
µA
VCCIO Digital supply current (halt mode)
No DC load, VCCIO = 3.6 V (8)
300
µA
ICC
(4)
(5)
(6)
(7)
mA
SYSCLK = 60 MHz,
ICLK = 20 MHz, VCC = 2.05 V
VCC Digital supply current (operating mode)
(1)
(2)
(3)
V
2
All other output
pins except RST (7)
ICCIO
2
4
VOL = VOL MAX
CLKOUT, TDO
High-level output current
V
8
All other output
pins (7)
RST, SPInCLK,
SPInSOMI,
SPInSIMO (6)
V
V
VCCIO – 0.2
CLKOUT, TDO
IOH
V
OSCIN only
Drain-to-source on
resistance
Low-level output current
UNIT
0.8
Input threshold voltage
IOL
MAX
–0.3
Vth
Input current (I/O pins)
TYP
All inputs (2) except
OSCIN
OSCIN only
II
MIN
0.15
Source currents (out of the device) are negative while sink currents (into the device) are positive.
This does not apply to the PORRST pin. For PORRST exceptions, see the RST and PORRST timings section.
These values help to determine the external RC network circuit. For more details, see the TMS470R1x System Module Reference Guide
(literature number SPNU189).
VOL and VOH are linear with respect to the amount of load current (IOL/IOH) applied.
Parameter does not apply to input-only or output-only pins.
n = 1–5.
The 2-mA buffers on this device are called zero-dominant buffers. If two of these buffers are shorted together and one is outputting a
low level and the other is outputting a high level, the resulting value is always low.
I/O pins configured as inputs or outputs with no load. All pulldown inputs ≤ 0.2 V. All pullup inputs ≥ VCCIO – 0.2 V.
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
25
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
over recommended operating free-air temperature range, T version (unless otherwise noted)
PARAMETER
ICCAD
ICCP
MAX
UNIT
VCCAD supply current (operating mode)
All frequencies, VCCAD = 3.6 V
TEST CONDITIONS
15
mA
VCCAD supply current (standby mode)
All frequencies, VCCAD = 3.6 V
20
µA
VCCAD supply current (halt mode)
All frequencies, VCCAD = 3.6 V
20
µA
VCCP = 3.6 V read operation
55
mA
VCCP = 3.6 V program and erase
70
mA
VCCP = 3.6 V standby mode
operation (9)
20
µA
VCCP = 3.6 V halt mode
operation (9)
20
µA
VCCP pump supply current
MIN
TYP
CI
Input capacitance
2
pF
CO
Output capacitance
3
pF
(9)
For flash banks/pumps in sleep mode.
Parameter Measurement Information
IOL
Tester Pin
Electronics
Output
Under
Test
50 Ω
V LOAD
CL
I OH
Where:
IOL
=
IOH
=
VLOAD =
CL
=
IOL MAX for the respective pin (A)
IOH MIN for the respective pin(A)
1.5 V
150-pF typical load-circuit capacitance(B)
A.
For these values, see the "Electrical Characteristics over Recommended Operating Free-Air Temperature Range"
table.
B.
All timing parameters measured using an external load capacitance of 150 pF unless otherwise noted.
Figure 4. Test Load Circuit
26
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
Timing Parameter Symbology
Timing parameter symbols have been created in accordance with JEDEC Standard 100. To shorten the symbols,
some of the pin names and other related terminology have been abbreviated as follows:
CM
Compaction, CMPCT
RD
Read
CO
CLKOUT
RST
Reset, RST
ER
Erase
RX
SCInRX
ICLK
Interface clock
S
Slave mode
M
Master mode
SCC
SCInCLK
OSC, OSCI
OSCIN
SIMO
SPInSIMO
OSCO
OSCOUT
SOMI
SPInSOMI
P
Program, PROG
SPC
SPInCLK
R
Ready
SYS
System clock
R0
Read margin 0, RDMRGN0
TX
SCInTX
R1
Read margin 1, RDMRGN1
Lowercase subscripts and their meanings are:
a
access time
r
rise time
c
cycle time (period)
su
setup time
d
delay time
t
transition time
f
fall time
v
valid time
h
hold time
w
pulse duration (width)
The following additional letters are used with these meanings:
H
High
X
Unknown, changing, or don't care level
L
Low
Z
High impedance
V
Valid
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
27
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
External Reference Resonator/Crystal Oscillator Clock Option
The oscillator is enabled by connecting the appropriate fundamental 4–20 MHz resonator/crystal and load
capacitors across the external OSCIN and OSCOUT pins as shown in Figure 5a. The oscillator is a single-stage
inverter held in bias by an integrated bias resistor. This resistor is disabled during leakage test measurement and
HALT mode. TI strongly encourages each customer to submit samples of the device to the
resonator/crystal vendors for validation. The vendors are equipped to determine what load capacitors will
best tune their resonator/crystal to the microcontroller device for optimum start-up and operation over
temperature/voltage extremes.
An external oscillator source can be used by connecting a 1.8-V clock signal to the OSCIN pin and leaving the
OSCOUT pin unconnected (open) as shown in Figure 5b.
OSCIN
C1(A)
OSCOUT
Crystal
C2(A)
OSCIN
OSCOUT
External
Clock Signal
(toggling 0-1.8 V)
(a)
A.
(b)
The values of C1 and C2 should be provided by the resonator/crystal vendor.
Figure 5. Crystal/Clock Connection
28
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
ZPLL AND CLOCK SPECIFICATIONS
Timing Requirements for ZPLL Circuits Enabled or Disabled
MIN
MAX
UNIT
4
20
MHz
f(OSC)
Input clock frequency
tc(OSC)
Cycle time, OSCIN
50
ns
tw(OSCIL)
Pulse duration, OSCIN low
15
ns
tw(OSCIH)
Pulse duration, OSCIN high
15
ns
f(OSCRST)
(1)
OSC FAIL frequency
(1)
53
kHz
Causes a device reset (specifically a clock reset) by setting the RST OSC FAIL (GLBCTRL.15) and the OSC FAIL flag (GLBSTAT.1)
bits equal to 1. For more detailed information on these bits and device resets, see the TMS470R1x System Module Reference Guide
(literature number SPNU189).
Switching Characteristics over Recommended Operating Conditions for Clocks (1) (2)
TEST CONDITIONS (3)
PARAMETER
f(SYS)
System clock frequency (4)
f(CONFIG)
System clock frequency
f(ICLK)
f(ECLK)
Interface clock frequency
External clock output frequency for ECP module
tc(SYS)
Cycle time, system clock
tc(CONFIG)
Cycle time, system clock
tc(ICLK)
tc(ECLK)
(1)
(2)
(3)
(4)
Cycle time, interface clock
Cycle time, ECP module external clock output
MAX
UNIT
Pipeline mode enabled
MIN
60
MHz
Pipeline mode disabled
24
MHz
Flash config mode
24
MHz
Pipeline mode enabled
25
MHz
Pipeline mode disabled
24
MHz
Pipeline mode enabled
25
MHz
Pipeline mode disabled
24
MHz
Pipeline mode enabled
16.7
ns
Pipeline mode disabled
41.6
ns
Flash config mode
41.6
ns
Pipeline mode enabled
40
ns
Pipeline mode disabled
41.6
ns
Pipeline mode enabled
40
ns
Pipeline mode disabled
41.6
ns
When PLLDIS = 0, f(SYS) = M ‫נ‬f(OSC)/R, where M = {4 or 8}, R = {1,2,3,4,5,6,7,8}. R is the system-clock divider determined by the
CLKDIVPRE [2:0] bits in the global control register (GLBCTRL[2:0]) and M is the PLL multiplier determined by the MULT4 bit
(GLBCTRL.3).
When PLLDIS = 1, f(SYS) = f(OSC)/R, where R = {1,2,3,4,5,6,7,8}.
f(ICLK) = f(SYS)/X, where X = {1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16}. X is the interface clock divider ratio determined by the PCR0[4:1]
bits in the SYS module.
f(ECLK) = f(ICLK)/N, where N = {1 to 256}. N is the ECP prescale value defined by the ECPCTRL[7:0] register bits in the ECP module.
Pipeline mode enabled or disabled is determined by the ENPIPE bit (FMREGOPT.0).
Flash Vread must be set to 5 V to achieve maximum system clock frequency.
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
29
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
Switching Characteristics over Recommended Operating Conditions for External Clocks (1) (2) (3)
(see Figure 6 and Figure 7)
PARAMETER
TEST CONDITIONS
MIN
SYSCLK or MCLK (4)
tw(COL)
Pulse duration, CLKOUT low
ICLK: X is even or 1 (5)
ICLK: X is odd and not 1
tw(COH)
Pulse duration, CLKOUT high
tw(EOL)
tw(EOH)
Pulse duration, ECLK low
Pulse duration, ECLK high
0.5tc(ICLK) – tf
(5)
0.5tc(SYS) – tr
ICLK: X is even or 1 (5)
0.5tc(ICLK) – tr
(5)
ns
ns
0.5tc(ICLK) – 0.5tc(SYS) – tr
N is even and X is even or odd
0.5tc(ECLK) – tf
N is odd and X is even
0.5tc(ECLK) – tf
N is odd and X is odd and not 1
0.5tc(ECLK) + 0.5tc(SYS) – tf
N is even and X is even or odd
0.5tc(ECLK) – tr
N is odd and X is even
N is odd and X is odd and not 1
(1)
(2)
(3)
(4)
(5)
UNIT
0.5tc(ICLK) + 0.5tc(SYS) – tf
SYSCLK or MCLK (4)
ICLK: X is odd and not 1
MAX
0.5tc(SYS) – tf
0.5tc(ECLK) – tr
ns
ns
0.5tc(ECLK) – 0.5tc(SYS) – tr
X = {1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16}. X is the interface clock divider ratio determined by the PCR0[4:1] bits in the SYS module.
N = {1 to 256}. N is the ECP prescale value defined by the ECPCTRL[7:0] register bits in the ECP module.
CLKOUT/ECLK pulse durations (low/high) are a function of the OSCIN pulse durations when PLLDIS is active.
Clock source bits are selected as either SYSCLK (CLKCNTL[6:5] = 11 binary) or MCLK (CLKCNTL[6:5] = 10 binary).
Clock source bits are selected as ICLK (CLKCNTL[6:5] = 01 binary).
tw(COH)
CLKOUT
tw(COL)
Figure 6. CLKOUT Timing Diagram
tw(EOH)
ECLK
tw(EOL)
Figure 7. ECLK Timing Diagram
30
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
RST AND PORRST TIMINGS
Timing Requirements for PORRST
(see Figure 8)
MIN
MAX UNIT
VCCPORL
VCC low supply level when PORRST must be active during power up
VCCPORH
VCC high supply level when PORRST must remain active during power up and become
active during power down
VCCIOPORL
VCCIO low supply level when PORRST must be active during power up
VCCIOPORH
VCCIO high supply level when PORRST must remain active during power up and become
active during power down
VIL
Low-level input voltage after VCCIO > VCCIOPORH
VIL(PORRST)
Low-level input voltage of PORRST before VCCIO > VCCIOPORL
tsu(PORRST)r
Setup time, PORRST active before VCCIO > VCCIOPORL during power up
0
ms
tsu(VCCIO)r
Setup time, VCCIO > VCCIOPORL before VCC > VCCPORL
0
ms
th(PORRST)r
Hold time, PORRST active after VCC > VCCPORH
1
ms
tsu(PORRST)f
Setup time, PORRST active before VCC ≤ VCCPORH during power down
8
µs
th(PORRST)rio
Hold time, PORRST active after VCC VCCIOPORH
1
ms
th(PORRST)d
Hold time, PORRST active after VCC < VCCPORL
0
ms
tsu(PORRST)fio
Setup time, PORRST active before VCC ≤ VCCIOPORH during power down
0
ns
tsu(VCCIO)f
Setup time, VCC < VCCPORL before VCCIO < VCCIOPORL
0
ns
V CCP /VCCIO
V CC
V CCIOPORH
th(PORRST)rio
V CCPORH
V CC
VCCP/VCCIO
PORRST
V
V
1.1
V
2.75
V
0.2 VCCIO
V
V
V CCIOPORH
V CCIO
tsu(VCCIO)f
V CC
tsu(PORRST)f
V CCPORH
tsu(PORRST)fio
tsu(PORRST)f
V CCPORL
th(PORRST)r
tsu(VCCIO)r
V CCIOPORL
V CCPORL
th(PORRST)d
tsu(PORRST)r
V IL(PORRST)
1.5
0.5
th(PORRST)r
V CCIOPORL
0.6
V IL
VIL
VIL
V IL
V IL(PORRST)
NOTE: VCCIO > 1.1 V before VCC > 0.6 V
Figure 8. PORRST Timing Diagram
Switching Characteristics over Recommended Operating Conditions for RST (1)
PARAMETER
tv(RST)
(1)
Valid time, RST active after PORRST inactive
Valid time, RST active (all others)
MIN
MAX UNIT
4112tc(OSC)
8tc(SYS)
ns
Specified values do NOT include rise/fall times. For rise and fall timings, see the "Switching Characteristics for Output Timings versus
Load Capacitance" table.
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
31
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
JTAG Scan Interface Timing (JTAG clock specification 10-MHz and 50-pF load on TDO output)
MIN
MAX
UNIT
tc(JTAG)
Cycle time, JTAG low and high period
50
ns
tsu(TDI/TMS - TCKr)
Setup time, TDI, TMS before TCK rise (TCKr)
15
ns
th(TCKr
Hold time, TDI, TMS after TCKr
15
ns
th(TCKf -TDO)
Hold time, TDO after TCKf
10
td(TCKf -TDO)
Delay time, TDO valid after TCK fall (TCKf)
-TDI/TMS)
ns
45
ns
Figure 9. JTAG Scan Timings
32
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
OUTPUT TIMINGS
Switching Characteristics for Output Timings versus Load Capacitance L)
(see Figure 10)
PARAMETER
tr
tf
tr
tf
tr
tf
(1)
Rise time, CLKOUT, AWD, TDO
Fall time, CLKOUT, AWD, TDO
Rise time, SPInCLK, SPInSOMI, SPInSIMO (1)
Fall time, RST, SPInCLK, SPInSOMI, SPInSIMO (1)
Rise time, all other output pins
Fall time, all other output pins
MIN
MAX
CL = 15 pF
0.5
2.50
CL = 50 pF
1.5
5
CL = 100 pF
3
9
CL = 150 pF
4.5
12.5
CL = 15 pF
0.5
2.5
CL = 50 pF
1.5
5
CL = 100 pF
3
9
CL = 150 pF
4.5
12.5
CL = 15 pF
2.5
8
CL = 50 pF
5
14
CL = 100 pF
9
23
CL = 150 pF
13
32
CL = 15 pF
2.5
8
CL = 50 pF
5
14
CL = 100 pF
9
23
CL = 150 pF
13
32
CL = 15 pF
2.5
12
CL = 50 pF
6.0
28
CL = 100 pF
12
50
CL = 150 pF
18
73
CL = 15 pF
3
12
CL = 50 pF
8.5
28
CL = 100 pF
16
50
CL = 150 pF
23
73
UNIT
ns
ns
ns
ns
ns
ns
Where n = 1-5.
tr
tf
80%
Output
VCC
80%
20%
20%
0
Figure 10. CMOS-Level Outputs
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
33
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
INPUT TIMINGS
Timing Requirements for Input Timings (1)
(see Figure 11)
MIN
tpw
(1)
Input minimum pulse width
MAX UNIT
tc(ICLK) + 10
ns
tc(ICLK) = interface clock cycle time = 1 / f(ICLK)
tpw
Input
80%
V CC
80%
20%
20%
0
Figure 11. CMOS-Level Inputs
FLASH TIMINGS
Timing Requirements for Program Flash (1)
tprog(16-bit)
Half word (16-bit) programming time
tprog(Total)
768K-byte programming time (2)
terase(sector)
Sector erase time
twec
Write/erase cycles at TA = –40°C to 125°C
(1)
(2)
34
MIN
TYP
MAX
UNIT
4
16
200
µs
6
20
s
1.7
50000
s
cycles
For more detailed information on the flash core sectors, see the flash program and erase section of this data sheet.
The 768K-byte programming time includes overhead of state machine.
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
SPIn MASTER MODE TIMING PARAMETERS
SPIn Master Mode External Timing Parameters
(CLOCK PHASE = 0, SPInCLK = output, SPInSIMO = output, and SPInSOMI = input) (1) (2) (3) (see Figure 12)
NO.
1
2 (5)
3 (5)
4 (5)
5 (5)
6 (5)
7 (5)
(1)
(2)
(3)
(4)
(5)
MIN
MAX
UNIT
100
256tc(ICLK)
ns
Pulse duration, SPInCLK high (clock polarity = 0)
0.5tc(SPC)M – tr
0.5tc(SPC)M + 5
tw(SPCL)M
Pulse duration, SPInCLK low (clock polarity = 1)
0.5tc(SPC)M – tf
0.5tc(SPC)M + 5
tw(SPCL)M
Pulse duration, SPInCLK low (clock polarity = 0)
0.5tc(SPC)M – tf
0.5tc(SPC)M + 5
tw(SPCH)M
Pulse duration, SPInCLK high (clock polarity = 1)
0.5tc(SPC)M – tr
0.5tc(SPC)M + 5
td(SPCH-SIMO)M
Delay time, SPInCLK high to SPInSIMO valid (clock polarity = 0)
10
td(SPCL-SIMO)M
Delay time, SPInCLK low to SPInSIMO valid (clock polarity = 1)
10
tv(SPCL-SIMO)M
Valid time, SPInSIMO data valid after SPInCLK low (clock polarity = 0)
tc(SPC)M – 5 – tf
tv(SPCH-SIMO)M
Valid time, SPInSIMO data valid after SPInCLK high (clock polarity = 1)
tc(SPC)M – 5 – tr
tsu(SOMI-SPCL)M
Setup time, SPInSOMI before SPInCLK low (clock polarity = 0)
6
tsu(SOMI-SPCH)M
Setup time, SPInSOMI before SPInCLK high (clock polarity = 1)
6
tv(SPCL-SOMI)M
Valid time, SPInSOMI data valid after SPInCLK low (clock polarity = 0)
4
tv(SPCH-SOMI)M
Valid time, SPInSOMI data valid after SPInCLK high (clock polarity = 1)
4
tc(SPC)M
Cycle time, SPInCLK (4)
tw(SPCH)M
ns
ns
ns
ns
ns
ns
The MASTER bit (SPInCTRL2.3) is set and the CLOCK PHASE bit (SPInCTRL2.0) is cleared.
tc(ICLK) = interface clock cycle time = 1/f(ICLK)
For rise and fall timings, see the "Switching Characteristics for Output Timings versus Load Capacitance" table.
When the SPI is in master mode, the following must be true:
For PS values from 1 to 255: tc(SPC)M ≥(PS +1)tc(ICLK) ≥ 100 ns, where PS is the prescale value set in the SPInCTL1[12:5] register bits.
For PS values of 0: tc(SPC)M = 2tc(ICLK) ≥ 100 ns.
The active edge of the SPInCLK signal referenced is controlled by the CLOCK POLARITY bit (SPInCTRL2.1).
1
SPInCLK
(clock polarity = 0)
2
3
SPInCLK
(clock polarity = 1)
4
5
SPInSIMO
Master Out Data Is Valid
6
7
SPInSOMI
Master In Data
Must Be Valid
Figure 12. SPIn Master Mode External Timing (CLOCK PHASE = 0)
SPIn Master Mode External Timing Parameters
(CLOCK PHASE = 1, SPInCLK = output, SPInSIMO = output, and SPInSOMI = input) (1) (2) (3) (see Figure 13)
(1)
(2)
(3)
The MASTER bit (SPInCTRL2.3) is set and the CLOCK PHASE bit (SPInCTRL2.0) is set.
tc(ICLK) = interface clock cycle time = 1/f(ICLK)
For rise and fall timings, see the "Switching Characteristics for Output Timings versus Load Capacitance" table.
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
35
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
SPIn Master Mode External Timing Parameters (continued)
(CLOCK PHASE = 1, SPInCLK = output, SPInSIMO = output, and SPInSOMI = input) (see Figure 13)
NO.
1
2 (5)
3 (5)
4
MIN
MAX
UNIT
100
256tc(ICLK)
ns
Pulse duration, SPInCLK high (clock polarity = 0)
0.5tc(SPC)M – tr
0.5tc(SPC)M + 5
tw(SPCL)M
Pulse duration, SPInCLK low (clock polarity = 1)
0.5tc(SPC)M – tf
0.5tc(SPC)M + 5
tw(SPCL)M
Pulse duration, SPInCLK low (clock polarity = 0)
0.5tc(SPC)M – tf
0.5tc(SPC)M + 5
tw(SPCH)M
Pulse duration, SPInCLK high (clock polarity = 1)
0.5tc(SPC)M – tr
0.5tc(SPC)M + 5
tv(SIMO-SPCH)M
Valid time, SPInCLK high after SPInSIMO data valid
(clock polarity = 0)
0.5tc(SPC)M –15
tv(SIMO-SPCL)M
Valid time, SPInCLK low after SPInSIMO data valid
(clock polarity = 1)
0.5tc(SPC)M – 15
tv(SPCH-SIMO)M
Valid time, SPInSIMO data valid after SPInCLK high
(clock polarity = 0)
0.5tc(SPC)M – 5 – tr
tv(SPCL-SIMO)M
Valid time, SPInSIMO data valid after SPInCLK low
(clock polarity = 1)
0.5tc(SPC)M – 5 – tf
tsu(SOMI-SPCH)M
Setup time, SPInSOMI before SPInCLK high
(clock polarity = 0)
6
tsu(SOMI-SPCL)M
Setup time, SPInSOMI before SPInCLK low
(clock polarity = 1)
6
tv(SPCH-SOMI)M
Valid time, SPInSOMI data valid after SPInCLK high
(clock polarity = 0)
4
tv(SPCL-SOMI)M
Valid time, SPInSOMI data valid after SPInCLK low
(clock polarity = 1)
4
tc(SPC)M
Cycle time, SPInCLK (4)
tw(SPCH)M
(5)
5 (5)
6 (5)
7
(4)
(5)
(5)
ns
ns
ns
ns
ns
ns
When the SPI is in master mode, the following must be true:
For PS values from 1 to 255: tc(SPC)M ≥ (PS +1)tc(ICLK) ≥ 100 ns, where PS is the prescale value set in the SPInCTL1[12:5] register bits.
For PS values of 0: tc(SPC)M = 2tc(ICLK) ≥ 100 ns.
The active edge of the SPInCLK signal referenced is controlled by the CLOCK POLARITY bit (SPInCTRL2.1).
1
SPInCLK
(clock polarity = 0)
2
3
SPInCLK
(clock polarity = 1)
4
5
SPInSIMO
Master Out Data Is Valid
Data Valid
6
7
SPInSOMI
Master In Data
Must Be Valid
Figure 13. SPIn Master Mode External Timing (CLOCK PHASE = 1)
36
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
SPIn SLAVE MODE TIMING PARAMETERS
SPIn Slave Mode External Timing Parameters
(CLOCK PHASE = 0, SPInCLK = input, SPInSIMO = input, and SPInSOMI = output) (1) (2) (3) (4) (see Figure 14)
NO.
1
2 (6)
3 (6)
4
MIN
MAX
UNIT
100
256tc(ICLK)
ns
Pulse duration, SPInCLK high (clock polarity = 0)
0.5tc(SPC)S – 0.25tc(ICLK)
0.5tc(SPC)S + 0.25tc(ICLK)
tw(SPCL)S
Pulse duration, SPInCLK low (clock polarity = 1)
0.5tc(SPC)S – 0.25tc(ICLK)
0.5tc(SPC)S + 0.25tc(ICLK)
tw(SPCL)S
Pulse duration, SPInCLK low (clock polarity = 0)
0.5tc(SPC)S – 0.25tc(ICLK)
0.5tc(SPC)S + 0.25tc(ICLK)
tw(SPCH)S
Pulse duration, SPInCLK high (clock polarity = 1)
0.5tc(SPC)S – 0.25tc(ICLK)
0.5tc(SPC)S + 0.25tc(ICLK)
td(SPCH-SOMI)S
Delay time, SPInCLK high to SPInSOMI valid
(clock polarity = 0)
6 + tr
td(SPCL-SOMI)S
Delay time, SPInCLK low to SPInSOMI valid
(clock polarity = 1)
6 + tf
tv(SPCH-SOMI)S
Valid time, SPInSOMI data valid after SPInCLK high
(clock polarity = 0)
tc(SPC)S – 6 – tr
tv(SPCL-SOMI)S
Valid time, SPInSOMI data valid after SPInCLK low
(clock polarity = 1)
tc(SPC)S – 6 – tf
tsu(SIMO-SPCL)S
Setup time, SPInSIMO before SPInCLK low
(clock polarity = 0)
6
tsu(SIMO-SPCH)S
Setup time, SPInSIMO before SPInCLK high
(clock polarity = 1)
6
tv(SPCL-SIMO)S
Valid time, SPInSIMO data valid after SPInCLK low
(clock polarity = 0)
6
tv(SPCH-SIMO)S
Valid time, SPInSIMO data valid after SPInCLK high
(clock polarity = 1)
6
tc(SPC)S
Cycle time, SPInCLK (5)
tw(SPCH)S
(6)
5 (6)
6 (6)
7
(1)
(2)
(3)
(4)
(5)
(6)
(6)
ns
ns
ns
ns
ns
ns
The MASTER bit (SPInCTRL2.3) is cleared and the CLOCK PHASE bit (SPInCTRL2.0) is cleared.
If the SPI is in slave mode, the following must be true: tc(SPC)S ≥ (PS + 1) tc(ICLK), where PS = prescale value set in SPInCTL1[12:5].
For rise and fall timings, see the "Switching Characteristics for Output Timings versus Load Capacitance" table.
tc(ICLK) = interface clock cycle time = 1/f(ICLK)
When the SPIn is in slave mode, the following must be true:
For PS values from 1 to 255: tc(SPC)S ≥ (PS +1)tc(ICLK) ≥ 100 ns, where PS is the prescale value set in the SPInCTL1[12:5] register bits.
For PS values of 0: tc(SPC)S = 2tc(ICLK) ≥ 100 ns.
The active edge of the SPInCLK signal referenced is controlled by the CLOCK POLARITY bit (SPInCTRL2.1).
1
SPInCLK
(clock polarity = 0)
2
3
SPInCLK
(clock polarity = 1)
4
55
SPInSOMI
SPISOMI Data Is Valid
6
7
SPInSIMO
SPISIMO Data
Must Be Valid
Figure 14. SPIn Slave Mode External Timing (CLOCK PHASE = 0)
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
37
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
SPIn Slave Mode External Timing Parameters
(CLOCK PHASE = 1, SPInCLK = input, SPInSIMO = input, and SPInSOMI = output) (1) (2) (3) (4) (see Figure 15)
NO.
1
2 (6)
3 (6)
MIN
MAX
UNIT
100
256tc(ICLK)
ns
Pulse duration, SPInCLK high (clock polarity = 0)
0.5tc(SPC)S – 0.25tc(ICLK)
0.5tc(SPC)S + 0.25tc(ICLK)
tw(SPCL)S
Pulse duration, SPInCLK low (clock polarity = 1)
0.5tc(SPC)S – 0.25tc(ICLK)
0.5tc(SPC)S + 0.25tc(ICLK)
tw(SPCL)S
Pulse duration, SPInCLK low (clock polarity = 0)
0.5tc(SPC)S – 0.25tc(ICLK)
0.5tc(SPC)S + 0.25tc(ICLK)
tw(SPCH)S
Pulse duration, SPInCLK high (clock polarity = 1)
0.5tc(SPC)S – 0.25tc(ICLK)
0.5tc(SPC)S + 0.25tc(ICLK)
tv(SOMI-SPCH)S
Valid time, SPInCLK high after SPInSOMI data valid
(clock polarity = 0)
0.5tc(SPC)S – 6 – tr
tv(SOMI-SPCL)S
Valid time, SPInCLK low after SPInSOMI data valid
(clock polarity = 1)
0.5tc(SPC)S – 6 – tf
tv(SPCH-SOMI)S
Valid time, SPInSOMI data valid after SPInCLK high
(clock polarity = 0)
0.5tc(SPC)S – 6 – tr
tv(SPCL-SOMI)S
Valid time, SPInSOMI data valid after SPInCLK low
(clock polarity = 1)
0.5tc(SPC)S – 6 – tf
tsu(SIMO-SPCH)S
Setup time, SPInSIMO before SPInCLK high
(clock polarity = 0)
6
tsu(SIMO-SPCL)S
Setup time, SPInSIMO before SPInCLK low
(clock polarity = 1)
6
tv(SPCH-SIMO)S
Valid time, SPInSIMO data valid after SPInCLK high
(clock polarity = 0)
6
tv(SPCL-SIMO)S
Valid time, SPInSIMO data valid after SPInCLK low
(clock polarity = 1)
6
tc(SPC)S
Cycle time, SPInCLK (5)
tw(SPCH)S
(6)
4
(6)
5
(6)
6
(6)
7
(1)
(2)
(3)
(4)
(5)
(6)
ns
ns
ns
ns
ns
ns
The MASTER bit (SPInCTRL2.3) is cleared and the CLOCK PHASE bit (SPInCTRL2.0) is set.
If the SPI is in slave mode, the following must be true: tc(SPC)S ≥ (PS + 1) tc(ICLK), where PS = prescale value set in SPInCTL1[12:5].
For rise and fall timings, see the "Switching Characteristics for Output Timings versus Load Capacitance" table.
tc(ICLK) = interface clock cycle time = 1/f(ICLK)
When the SPIn is in slave mode, the following must be true:
For PS values from 1 to 255: tc(SPC)S ≥ (PS +1)tc(ICLK) ≥ 100 ns, where PS is the prescale value set in the SPInCTL1[12:5] register bits.
For PS values of 0: tc(SPC)S = 2tc(ICLK) ≥ 100 ns.
The active edge of the SPInCLK signal referenced is controlled by the CLOCK POLARITY bit (SPInCTRL2.1).
1
SPInCLK
(clock polarity = 0)
2
3
SPInCLK
(clock polarity = 1)
4
5
SPInSOMI
SPISOMI Data Is Valid
Data Valid
6
7
SPInSIMO
SPISIMO Data Must
Be Valid
Figure 15. SPIn Slave Mode External Timing (CLOCK PHASE = 1)
38
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
SCIn ISOSYNCHRONOUS MODE TIMINGS INTERNAL CLOCK
Timing Requirements for Internal Clock SCIn Isosynchronous Mode (1) (2) (3)
(see Figure 16)
(BAUD + 1)
IS EVEN OR BAUD = 0
(BAUD + 1)
IS ODD AND BAUD ≠ 0
UNIT
MIN
MAX
MIN
MAX
2tc(ICLK)
224 tc(ICLK)
3tc(ICLK)
(224 -1) tc(ICLK)
ns
tc(SCC)
Cycle time,
SCInCLK
tw(SCCL)
Pulse duration,
SCInCLK low
0.5tc(SCC) – tf
0.5tc(SCC) + 5
0.5tc(SCC) + 0.5tc(ICLK) – tf
0.5tc(SCC) + 0.5tc(ICLK)
ns
tw(SCCH)
Pulse duration,
SCInCLK high
0.5tc(SCC) – tr
0.5tc(SCC) + 5
0.5tc(SCC) – 0.5tc(ICLK) – tr
0.5tc(SCC) – 0.5tc(ICLK)
ns
td(SCCH-TXV)
Delay time,
SCInCLK high to
SCInTX valid
10
ns
tv(TX)
Valid time,
SCInTX data
after SCInCLK
low
tc(SCC) – 10
tc(SCC) – 10
ns
tsu(RX-SCCL)
Setup time,
SCInRX before
SCInCLK low
tc(ICLK) + tf + 20
tc(ICLK) + tf + 20
ns
tv(SCCL-RX)
Valid time,
SCInRX data
after SCInCLK
low
–tc(ICLK) + tf + 20
–tc(ICLK) + tf + 20
ns
(1)
(2)
(3)
10
BAUD = 24-bit concatenated value formed by the SCI[H,M,L]BAUD registers.
tc(ICLK) = interface clock cycle time = 1/f(ICLK)
For rise and fall timings, see the "Switching Characteristics for Output Timings versus Load Capacitance" table.
tc(SCC)
tw(SCCL)
tw(SCCH)
SCICLK
tv(TX)
td(SCCHĆTXV)
Data Valid
SCITX
tsu(RXĆSCCL)
SCIRX
A.
tv(SCCLĆRX)
Data Valid
Data transmission/reception characteristics for isosynchronous mode with internal clocking are similar to the
asynchronous mode. Data transmission occurs on the SCICLK rising edge, and data reception occurs on the SCICLK
falling edge.
Figure 16. SCIn Isosynchronous Mode Timing Diagram for Internal Clock
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
39
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
SCIn ISOSYNCHRONOUS MODE TIMINGS EXTERNAL CLOCK
Timing Requirements for External Clock SCIn Isosynchronous Mode (1) (2)
(see Figure 17)
MIN
MAX
UNIT
tc(SCC)
Cycle time, SCInCLK (3)
tw(SCCH)
Pulse duration, SCInCLK high
0.5tc(SCC) – 0.25tc(ICLK)
0.5tc(SCC) + 0.25tc(ICLK)
ns
tw(SCCL)
Pulse duration, SCInCLK low
0.5tc(SCC) – 0.25tc(ICLK)
0.5tc(SCC) + 0.25tc(ICLK)
ns
td(SCCH-TXV)
Delay time, SCInCLK high to SCInTX valid
2tc(ICLK) + 12 + tr
ns
tv(TX)
Valid time, SCInTX data after SCInCLK low
tsu(RX-SCCL)
Setup time, SCInRX before SCInCLK low
tv(SCCL-RX)
Valid time, SCInRX data after SCInCLK low
(1)
(2)
(3)
8tc(ICLK)
ns
2tc(SCC) – 10
ns
0
ns
2tc(ICLK) + 10
ns
tc(ICLK) = interface clock cycle time = 1/f(ICLK)
For rise and fall timings, see the "Switching Characteristics for Output Timings versus Load Capacitance" table.
When driving an external SCInCLK, the following must be true: tc(SCC) ≥ 8tc(ICLK).
tc(SCC)
tw(SCCH)
tw(SCCL)
SCICLK
tv(TX)
td(SCCHĆTXV)
Data Valid
SCITX
tsu(RXĆSCCL)
SCIRX
A.
tv(SCCLĆRX)
Data Valid
Data transmission / reception characteristics for isosynchronous mode with external clocking are similar to the
asynchronous mode. Data transmission occurs on the SCICLK rising edge, and data reception occurs on the SCICLK
falling edge.
Figure 17. SCIn Isosynchronous Mode Timing Diagram for External Clock
40
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
HIGH-END TIMER (HET) TIMINGS
Minimum PWM Output Pulse Width:
This is equal to one high resolution clock period (HRP). The HRP is defined by the 6-bit high resolution prescale
factor (hr), which is user defined, giving prescale factors of 1 to 64, with a linear increment of codes.
Therefore, the minimum PWM output pulse width = HRP(min) = hr(min)/SYSCLK = 1/SYSCLK
For example, for a SYSCLK of 30 MHz, the minimum PWM output pulse width = 1/30 = 33.33ns
Minimum Input Pulses that Can Be Captured:
The input pulse width must be greater or equal to the low resolution clock period (LRP), i.e., the HET loop (the
HET program must fit within the LRP). The LRP is defined by the 3-bit loop-resolution prescale factor (lr), which
is user defined, with a power of 2 increment of codes. That is, the value of lr can be 1, 2, 4, 8, 16, or 32.
Therefore, the minimum input pulse width = LRP(min) = hr(min) * lr(min)/SYSCLK = 1 * 1/SYSCLK
For example, with a SYSCLK of 30 MHz, the minimum input pulse width = 1 * 1/30 = 33.33 ns
NOTE:
Once the input pulse width is greater than LRP, the resolution of the measurement is
still HRP. (That is, the captured value gives the number of HRP clocks inside the
pulse.)
Abbreviations:
hr = HET high resolution divide rate = 1, 2, 3,...63, 64
lr = HET low resolution divide rate = 1, 2, 4, 8, 16, 32
High resolution clock period = HRP = hr/SYSCLK
Loop resolution clock period = LRP = hr*lr/SYSCLK
HIGH-END CAN CONTROLLER (HECCn) MODE TIMINGS
Dynamic Characteristics for the CANnHTX and CANnHRX Pins
PARAMETER
td(CANnHTX)
Delay time, transmit shift register to CANnHTX pin (1)
td(CANnHRX)
Delay time, CANnHRX pin to receive shift register
(1)
MIN
MAX
UNIT
15
ns
5
ns
These values do not include rise/fall times of the output buffer.
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
41
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
MULTI-BUFFERED A-TO-D CONVERTER (MibADC)
The multi-buffered A-to-D converter (MibADC) has a separate power bus for its analog circuitry that enhances
the A-to-D performance by preventing digital switching noise on the logic circuitry, which could be present on VSS
and VCC, from coupling into the A-to-D analog stage. All A-to-D specifications are given with respect to ADREFLO
unless otherwise noted.
Resolution
10 bits (1024 values)
Monotonic
Assured
00h to 3FFh [00 for VAI ≤ ADREFLO; 3FFh for VAI ≥ ADREFHI]
Output conversion code
Table 10. MibADC Recommended Operating Conditions (1)
MIN
MAX
UNIT
ADREFHI
A-to-D high-voltage reference source
VSSAD
VCCAD
V
ADREFLO
A-to-D low-voltage reference source
VSSAD
VCCAD
V
VAI
Analog input voltage
VSSAD – 0.3
VCCAD + 0.3
V
–2
2
mA
(2)
Analog input clamp current
(VAI < VSSAD – 0.3 or VAI > VCCAD + 0.3)
IAIC
(1)
(2)
For VCCAD and VSSAD recommended operating conditions, see the "Device Recommended Operating Conditions" table.
Input currents into any ADC input channel outside the specified limits could affect conversion results of other channels.
Table 11. Operating Characteristics Over Full Ranges of Recommended Operating Conditions (1) (2)
PARAMETER
RI
DESCRIPTION/CONDITIONS
Analog input resistance
MIN
See Figure 18.
TYP
250
Conversion
MAX UNIT
500
Ω
10
pF
CI
Analog input capacitance
See Figure 18.
IAIL
Analog input leakage current
See Figure 18.
IADREFHI
ADREFHI input current
ADREFHI = 3.6 V, ADREFLO = VSSAD
CR
Conversion range over which specified
accuracy is maintained
ADREFHI - ADREFLO
EDNL
Differential nonlinearity error
Difference between the actual step width
and the ideal value. See Figure 19.
±1.5 LSB
EINL
Integral nonlinearity error
Maximum deviation from the best straight
line through the MibADC. MibADC
transfer characteristics, excluding the
quantization error. See Figure 20.
±2.0 LSB
E TOT
Total error/absolute accuracy
Maximum value of the difference
between an analog value and the ideal
midstep value. See Figure 21.
(1)
(2)
42
Sampling
–1
3
30
pF
1
µA
5
mA
3.6
±2
V
LSB
VCCAD = ADREFHI
1 LSB = (ADREFHI – ADREFLO)/210 for the MibADC
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
External
Rs
MibADC
Input Pin
Ri
Sample Switch
Sample
Capacitor
Parasitic
Capacitance
V src
R leak
Ci
Figure 18. MibADC Input Equivalent Circuit
Multi-Buffer ADC Timing Requirements
MIN
NOM
MAX UNIT
tc(ADCLK)
Cycle time, MibADC clock
td(SH)
Delay time, sample and hold time
td)
Delay time, conversion time
td(SHC) (1)
Delay time, total sample/hold and conversion time
1.55
µs
(1)
0.05
µs
1
µs
0.55
µs
This is the minimum sample/hold and conversion time that can be achieved. These parameters are dependent on many factors; for
more details, see the TMS470R1x Multi-Buffered Analog-to-Digital Converter (MibADC) Reference Guide (literature number SPNU206).
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
43
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
The differential nonlinearity error shown in Figure 19 (sometimes referred to as differential linearity) is the
difference between an actual step width and the ideal value of 1 LSB.
!
!
A.
1 LSB = (ADREFHI - ADREFLO)/210
Figure 19. Differential Nonlinearity (DNL)
The integral nonlinearity error shown in Figure 20 (sometimes referred to as linearity error) is the deviation of the
values on the actual transfer function from a straight line.
0 ... 111
0 ... 110
Ideal
Transition
0 ... 101
Actual
Transition
0 ... 100
At Transition
011/100
(ć 1/2 LSB)
0 ... 011
0 ... 010
End-Point Lin. Error
0 ... 001
At Transition
001/010 (ć 1/4 LSB)
0 ... 000
0
1
2
3
4
5
6
7
Analog Input Value (LSB)
A.
1 LSB = (ADREFHI - ADREFLO)/210
Figure 20. Integral Nonlinearity (INL) Error
44
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
TMS470R1B768
www.ti.com ......................................................................................................................................................... SPNS108B – AUGUST 2005 – REVISED MAY 2008
The absolute accuracy or total error of an MibADC as shown in Figure 21 is the maximum value of the difference
between an analog value and the ideal midstep value.
A.
1 LSB = (ADREFHI - ADREFLO)/210
Figure 21. Absolute Accuracy (Total) Error
Thermal Resistance Characteristics
°C/W
PARAMETER
RθJA
43
RθJC
6.5
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
45
TMS470R1B768
SPNS108B – AUGUST 2005 – REVISED MAY 2008 ......................................................................................................................................................... www.ti.com
Revision History
This revision history highlights the changes made to the device-specific data sheet SPNS108.
Table 12. Revision History
SPNS108A to SPNS108B
Corrected the device identification code register value from 0xn83F to 0xn87F in Device Identification Code Register.
SPNS108 to SPNS108A
Revised the Family Nomenclature drawing to add Q version of the temperature range.
Revised "Absolute Maximum Ratings" table to add Q version of the temperature range.
Revised "Device Recommended Operating Conditions" table to add Q version of the temperature range.
Added note to PORRST Timing Diagram.
Changed TA range to –40°C to 125°C on twec in "Timing Requirements for Program Flash" table.
Added twec MIN value of 50000 and deleted MAX value in "Timing Requirements for Program Flash" table.
Changed terase(sector) TYP value to 1.7 and removed MAX value in "Timing Requirements for Program Flash" table.
46
Submit Documentation Feedback
Copyright © 2005–2008, Texas Instruments Incorporated
Product Folder Link(s): TMS470R1B768
PACKAGE OPTION ADDENDUM
www.ti.com
7-Apr-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TMP470R1B768PGE
ACTIVE
LQFP
PGE
144
TMS470R1B768PGET
ACTIVE
LQFP
PGE
144
60
Lead/Ball Finish
TBD
Call TI
Green (RoHS &
no Sb/Br)
CU NIPDAU
MSL Peak Temp (3)
Call TI
Level-3-260C-168 HR
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MTQF017A – OCTOBER 1994 – REVISED DECEMBER 1996
PGE (S-PQFP-G144)
PLASTIC QUAD FLATPACK
108
73
109
72
0,27
0,17
0,08 M
0,50
144
0,13 NOM
37
1
36
Gage Plane
17,50 TYP
20,20 SQ
19,80
22,20
SQ
21,80
0,25
0,05 MIN
0°– 7°
0,75
0,45
1,45
1,35
Seating Plane
0,08
1,60 MAX
4040147 / C 10/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated