TI UCC3750

application
INFO
available
Source Ringer Controller
UCC2750
UCC3750
PRELIMINARY
FEATURES
DESCRIPTION
• Provides Control for Flyback Based
Four Quadrant Amplifier Topology
The UCC3750 Source Ringer Controller provides a complete control and
drive solution for a four quadrant flyback-based ring generator circuit. The
IC controls a primary side switch, which is modulated when power transfer
is taking place from input to output. It also controls two secondary
switches which act as synchronous rectifier switches during positive
power flow. These switches are pulse-width-modulated when the power is
being delivered back to the source.
• Onboard Sine Wave Reference with
Low THD
• Selectable Ringing Frequency for
Different Phone Systems (20Hz,
25Hz and 50Hz)
• Programmable Output Amplitude and
DC Offset
• DC Current Limiting for Short Circuit
Protection
• Secondary Side Voltage Mode
Control
• Operates from a Single 5V Supply
The UCC3750 has an onboard sine wave reference with programmable
frequencies of 20Hz, 25Hz and 50Hz. The reference is derived from a
high-frequency (32kHz) crystal connected externally. Two frequency-select pins control an internal divider to give a sinusoidal output at
20Hz, 25Hz or 50Hz. The ring generator can also be used at other frequencies by supplying externally generated sine-waves to the chip or by
clocking the crystal input at a fixed multiple of the desired frequency.
Other features included in the UCC3750 are programmable DC current
limit (with buffer amplifier), a charge-pump circuit for gate drive voltage, internal 3V and 7.5V references, a triangular clock oscillator and a buffer
amplifier for adding programmable DC offset to the output voltage. The
UCC3750 also provides an uncommitted amplifier (AMP) for other signal
processing requirements.
TYPICAL APPLICATION
0V
VOUT
–48V
VIN
48V
VOUT
28
26
GD2
2
27
25
GD3 ENBL
GD1
REF
VCP
4
UCC3750
24
RT
VS2
6
23
CT
VS1
5
1
RGOOD
VDD
7
11
OUTDC
OUT2
15
NEG2
18
OUT1
16
NEG1
17
SINFLT
10
5V
12
NEGDC
13
AMPOUT
14
AMPIN
22
XTAL1
21
XTAL2
20
FS0
19
FS1
SINREF
SWRLY
GND
9
8
3
C17
0.047µF
UDG-99073
SLUS172A - DECEMBER 1999
UCC2750
UCC3750
CONNECTION DIAGRAM
ABSOLUTE MAXIMUM RATINGS
Input Supply Voltage
VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5V
Maximum Forced Voltage
VCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3V to 13.2V
VS1, VS2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3V to 5V
OUT1, OUT2, AMPOUT, OUTDC
Maximum Forced Voltage . . . . . . . . . . . . . . . . –0.3V to 7.5V
Maximum Forced Current . . . . . . . . . . . . . . Internally Limited
NEG1, NEG2, AMPIN, NEGDC
Maximum Forced Voltage . . . . . . . . . . . . . . . . –0.3V to 7.5V
SINREF, SINFLT
Maximum Forced Voltage . . . . . . . . . . . . . . . . –0.3V to 7.5V
Logic Inputs
Maximum Forced Voltage . . . . . . . . . . . . . . . . –0.3V to 7.5V
Reference Output Current (REF) . . . . . . . . . . Internally Limited
Output Current (GD1, GD2, GD3)
Pulsed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5A
Storage Temperature . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . –55°C to +150°C
Lead Temperature (Soldering, 10 Sec.). . . . . . . . . . . . . +300°C
DIL-28, SOIC- 28 (Top
View)
Unless otherwise indicated, voltages are reference to ground
and currents are positive into, negative out of the specified terminal. Pulsed is defined as a less than 10% duty cycle with a
maximum duration of 500ns. Consult Packaging Section of
Databook for thermal limitations and considerations of packages.
RGOOD
1
28
GD2
GD1
2
27
ENBL
GND
3
26
GD3
VCP
4
25
REF
VS1
5
24
RT
VS2
6
23
CT
VDD
7
22
XTAL1
SWRLY
8
21
XTAL2
SINREF
9
20
FS0
SINFLT
10
19
FS1
OUTDC
11
18
NEG2
NEGDC
12
17
NEG1
AMPOUT
13
16
OUT1
AMPIN
14
15
OUT2
ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for TA = 0°C to 70°C for the
UCC3750, –40°C to +85°C for the UCC2750, RT = 14k, CT = 470pF, CREF = 0.1µF, FS0 = 0, FS1 = 0, VDD = 5V. TA = TJ.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNITS
VDD Supply
Supply Current - Active
With 12V Supplied to VCP and Charge Pump
Disabled
0.5
1
mA
7.55
7.8
V
Internal Reference w/External Bypass
Output Voltage (REF)
7.3
Load Regulation
IREF = 0mA – 2mA
30
60
mV
Line Regulation
VCP = 10V to 13V, IREF = 1mA
3
15
mV
2.9
3
3.1
V
0.7125
0.75
0.7875
V
500
600
nA
Amplifier
Input Voltage
Error, DC Offset and Amp Amplifiers
DC Limit Amplifier
Input Bias Current
AVOL
VOUT = 2V to 4V
VOH
Source 100µA
70
VOL
Sink 100µA
Short Circuit Current
VIN = 0V and 5V with VOUT = 0V and 5V
0.5
Accuracy
TJ = 25°C, Program Frequency–Reference
Frequency
–1
Total Harmonic Distortion
(Note 1)
Amplitude
Peak
5.35
dB
6
7.0
V
0.2
0.65
V
2
3
mA
0
1
Hz
2
%
Sine Reference
Offset
2
0.475
0.5
0.525
V
2.85
3.0
3.15
V
UCC2750
UCC3750
ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for TA = 0°C to 70°C for the
UCC3750, –40°C to +85°C for the UCC2750, RT = 14k, CT = 470pF, CREF = 0.1µF, FS0 = 0, FS1 = 0, VDD = 5V. TA = TJ.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNITS
Oscillator
Accuracy
108
128
148
kHz
Peak Voltage
4.6
4.75
4.9
V
Valley Voltage
2.9
3.05
3.2
V
Switch Pull Up Resistance (VS1, VS2)
10
30
Ω
Switch Pull Down Resistance (VS1, VS2)
10
30
Ω
12
14
V
Charge Pump
VDD = 5V, IVCP = 10mA
Output Voltage (VCP)
11
Output Drivers
Pull Up Resistance
9
15
Ω
Pull Down Resistance
9
15
Ω
Rise Time
CL = 2.7nF
50
100
ns
Fall Time
CL = 2.7nF
50
100
ns
Current Limit
DC Limit Threshold Voltage Positive
R5/R6 = 3
0.4
0.5
0.6
V
DC Limit Threshold Voltage Negative
R5/R6 = 3
–0.6
–0.5
–0.4
V
Duty Cycle
Maximum PWM Duty Cycle
48
Rectifier Duty Cycle
50
%
50
%
Note 1: Guaranteed by measuring the steps of the PWL Sine Wave.
STATE
0
1
2
3
4
% VCC
0.3333
0.3384
0.3528
0.3745
0.4
VALUE FOR REF = 7.5
2.5
2.538
2.646
2.808
3
STATE
5
6
7
8
% VCC
0.4255
0.4471
0.4616
0.4666
VALUE FOR REF = 7.5
3.191
3.353
3.462
3.5
PIN DESCRIPTIONS
AMPIN: Inverting input of the uncommitted amplifier.
Table I. Frequency selection table
(for 32kHz crystal).
AMPOUT: Output of the uncommitted amplifier.
FS0
0
1
0
1
CT: This pin programs the internal PWM oscillator
frequency. Capacitor from CT to GND sets the charge
and discharge time of the oscillator.
ENBL: Logic input which enables the outputs and the
charge pump when high. ENBL should be pulled low to
turn the outputs off.
FS1
0
0
1
1
SINREF (Hz)
20
25
50
High Impedance
GD1: Output driver that controls the primary side switch
in a flyback converter through a gate drive transformer.
The output signal on this pin is PWM during positive
power transfer modes and zero during negative power
transfer modes.
FS0, FS1: Frequency select pins for the internal
sine-wave generator. Table 1 provides the SINREF
frequencies as a function of FS0 and FS1 when a 32kHz
crystal is used at the crystal inputs (XTAL1, XTAL2).
Other proportional frequencies can be obtained with a
different crystal. Inputs FS0 and FS1 are TTL compatible.
3
UCC2750
UCC3750
PIN DESCRIPTIONS (cont.)
GD2: Output driver that controls the p-channel secondary
side switch in the flyback converter. The output signal on
this pin is PWM during mode 4 (Fig. 2) when the
reference signal is negative and power is being returned
to the input. This pin functions as a synchronous rectifier
output during mode 1 with positive reference signal and
positive power transfer. This output is logically inverted to
provide the correct polarity drive signal for a p-channel
switch.
REF: Internal 7.5V reference. For best results, bypass to
GND with a ceramic capacitor(>0.1µF).
GD3: Output driver that controls the n-channel secondary
side switch in the flyback converter. The output signal on
this pin is PWM during mode 2 (Fig. 2) when the
reference signal is positive and power is being returned
to the input. This pin functions as a synchronous rectifier
output during mode 3 with a negative reference signal
and positive power transfer.
SINFLT: This signal is the buffered version of SINREF.
This signal is summed with the DC offset level with
appropriate scaling.
RGOOD: Logic output that indicates that the error
amplifier output is within range (0< D< 0.5). This pin can
source upto 0.5mA of current.
RT: Resistor from RT to GND helps set the oscillator
frequency. RT programs the charge and discharge
currents of CT.
GND: Reference point for the internal reference and all
thresholds. Also provides the signal return path for all
other pins.
SINREF: This pin is the output of the sine-wave
reference generator. It has a high output impedance
(≈25kΩ). A 0.01µF capacitor to GND is recommended to
provide smoothing of the sinewave. When FS0 and FS1
are both set high, the sine reference generator is
disabled allowing this pin to accept an external sinewave
input.
NEG1: Inverting input of the buffer amplifier that acts as
a summing junction for the DC (battery) offset voltage
and sinewave reference.
SWRLY: Logic output that leads the battery offset
crossings (by typically 5ms) to allow “zero voltage” relay
switching. This pin can typically source 250µA.
NEG2: Inverting input of the error amplifier where the
ringer output voltage and the reference signal with the
desired offset are applied with a weighted sum.
Feedback compensation is connected between NEG2
and OUT2.
XTAL1: Crystal connection for external crystal. This pin
can be also used to clock the internal sine wave
generator when XTAL2 is connected to VDD/2.
XTAL2: Crystal connection for external crystal.
VCP: External connection for charge pump storage
capacitor. A capacitance ≥2.2mF is recommended for
low charge pump output ripple. The voltage at this pin is
used by the output drivers for gate drive voltages.
Alternatively, a regulated gate drive voltage (>10V) can
be connected at this pin while leaving the charge pump
circuit at nodes VS1, VS2 disconnected.
NEGDC: Inverting input of the amplifier used for DC
current limiting.
OUT1: Output of the buffer amplifier that provides scaling
and filtering for the reference signal before feeding it into
the error amplifier. This output is also used internally to
select the PWM mode for the flyback converter.
OUT2: Output of the error amplifier. Used to connect
compensation components. This output’s absolute value
determines the duty cycle of the PWM pulse. The polarity
of this signal also determines the PWM mode.
VDD: External supply input used to bias internal logic
functions. Typically a regulated 5V supply is connected
between this pin and GND. It also is the input voltage for
the voltage tripler circuit to generate the gate drive
voltage.
OUTDC: Output of the DC current limit amplifier. The DC
current limit is activated when this pin is above 4.5V or
below 1.5V.
VS1, VS2: Voltage switches for the voltage tripler
(charge pump circuit). They provide different voltage
4
UCC2750
UCC3750
DETAILED BLOCK DIAGRAM
SWRLY FS0
8
XTAL1
XTAL2
XTAL
OSC
21
13
AMPIN
14
19
SINFLT NEG1
9
10
16
REF
VCP
MODE
VCM
4
PWM
MAG
4
VS1
5
VS2
6
VDD
7
CHARGE
PUMP
INTERNAL
REFERENCE
REF=7.5V
VCM = 3.0V
CONTROL LOGIC
MODE SIGN
SIGN
DC
CURRENT
LIMIT
VCM
SIGN
ERROR
AMP
AMP
12
MAG
FULLWAVE
RECTIFIER
VCM
DC OFFSET AMP
11
VCP
15
REF
VCM
REF
NEGDC
OUT2
18
SINE REFERENCE
GENERATOR
VCM
OUTDC
OUT1 NEG2
17
REF
22
AMPOUT
FS1 SINREF
20
OUT1
OUT2
0
0
PWM
OFF
0
1
OFF
PWM
OUT3
RECIRC
OFF
1
0
OFF
1
1
PWM RECIRC
OFF
2
GD1
28
GD2
26
GD3
VCP
VCP
PWM
OFF
RAMP
CLOCK
VCM
GENERATOR
25
3
24
23
1
27
REF
GND
RT
CT
RGOOD
ENBL
UDG-99074
Note: All pin numbers are for N or DW Packages.
APPLICATION INFORMATION
The UCC3750 provides complete control and protection
functions for a four quadrant flyback converter used to
generate ring signals for telephone circuits. A typical application circuit for a 15 REN ring generator is shown in
Fig. 1.
DC-DC converter operation where Q1 is modulated with
the PWM signal and rectification is provided through the
Q2, DR2 path to provide a positive output proportional to
the increasing, positive reference voltage. The
pulse-width is controlled by the error amplifier output to
increase or decrease the output as dictated by the reference. The maximum duty cycle is limited to 50% to prevent DR1 from turning on prior to Q2/DR2.
As shown, the flyback converter takes a DC input (typically 48V) and provides an isolated output with a programmable frequency (and amplitude) AC signal
superimposed on a programmable DC offset. The power
path consists of a primary side PWM switch Q1, primary
return rectifier DR1, a 4-winding transformer T1, output
rectifiers DR2 and DR3, synchronous/PWM switches Q2
and Q3, and output filter CF. Resistor RSENSE provides
the output current sensing for protection circuits.
In mode 2, the reference begins to decrease, necessitating that the power transfer back to the input. For this
mode, switch Q3 needs to be modulated while DR1 acts
as the rectifier back to the input. The UCC3750 has
mode decoding circuitry which automatically directs the
PWM signal to Q3 and turns off Q1.
Different operating modes of the converter are depicted
in Table 2. Fig. 2 shows the output voltage and current
waveforms for a purely capacitive load and identifies the
four operating modes. Fig. 3 shows the PWM waveforms
for the circuit and Fig. 4a - 4d show the equivalent circuits under the operating modes. The addition of Q2, Q3
and primary diode facilitates true four quadrant operation
where both the output voltage and power transfer can be
bi-directional. Mode 1 is similar to the commonly used
Table II. Operating modes.
5
Mode
Reference
Polarity
Power
Flow
E.A.
Output
1
2
3
4
+
+
–
–
+
–
+
–
–
+
+
–
Source Rectifier
(PWM) Switch
Switch
Q1
Q2
Q3
(D1)
Q1
Q3
Q2
(D1)
RTN
VIN
C23
C1
C2
0.47µF 100µF 100µF
R22
C22
R1
10k
R23
Figure 1. Typical application circuit.
6
1
CR9
3
4
Q6
MPSA06
2
5
1
6
Q5
2 Q4
2N5457
3
1 2N7001DICT
3
2
1
C3 0.1µF
R20
1
2
C21
T2
R2
R6
10k
3
VDD
C5
0.47µF
4
Q3
S3
S2
S4
S1
X1 32kHz
R5 30k
R9
AMPIN
XTAL1
XTAL2
14
22
21
19
SWRLY
8
9
C17
0.047µF
27
25
R18
16
OUT1
3
GND
SINFLT
10
17
18
NEG1
C11 0.22µF
CR5
C9
0.47µF
VDD
C10
2.2µF
C16 2.2µF
R12 2.7k
C18
22µF
R14 3.3M
C13
1µF
C19
100µF
R26
REF
R15 15k
R13 62k
R25 10k C14 1nF
R11 148k
CR7
C12 0.22µF CR6
15
7
5
6
4
NEG2
OUT2
VDD
VS1
VS2
VCP
ENBL REF
SINREF
FS1
FS0
AMPOUT
13
20
NEGDC
OUTDC
RGOOD
CT
RT
GD1
26
GND
GD3
12
11
1
23
24
2
28
GD2
C4
1µF
250V
R17
CR12
C6 0.1µF
C7 470pF
R4 16k
R3
CR10
CR8
IRF840
MTP2P50E
Q2
CR3 BYV26C
CR2
BYV99
R21
7,9
10
CR1
BYV99
T1
C20
VB
REF
VDD
5V
R27
R10
148k
VOUT
UCC2750
UCC3750
APPLICATION INFORMATION (cont.)
UDG-99075
UCC2750
UCC3750
APPLICATION INFORMATION (cont.)
When the reference signal goes from positive to negative, a transition is made from mode 2 to mode 3. In
mode 3, the converter once again acts as a DC-DC
flyback converter (with negative output). Similar to mode
1, Q1 is controlled by the PWM output, however, the rectifying path is now through Q3/DR3 as the output polarity
is reversed. At the mode boundaries, there could be
some distortion which won’t affect the THD too much as
it is near zero crossings. Finally, as the reference signal
starts increasing towards zero, the direction of power
transfer is again reversed and Q2 is PWMed in mode 4.
It should be noted that in modes 2 and 3 when the reference is decreasing, the phase of the feedback path is inverted compared to the other two modes. Traditional
PWM methods will result in instability due to this characteristic. The UCC3750 separates the error signal magnitude and polarity and determines the correct PWM signal
based on a separate mode determination circuit.
UDG-96172-1
UDG-96173
Figure 2. Operating modes.
Figure 3. Circuit waveforms.
UDG-96162-1
UDG-96163
Figure 4a. Mode 1: Forward power transfer, positive
output.
Figure 4b. Mode 2: Reverse power transfer, positive
output.
UDG-96164-1
UDG-96165-1
Figure 4c. Mode 3: Forward power transfer, negative
output.
Figure 4d. Mode 4: Reverse power transfer, negative
output.
7
UCC2750
UCC3750
APPLICATION INFORMATION (cont.)
R13
R13 R13 

VOUT1 =  1 +
+
• REF
 • VCM –
R26
R14 R26 

Sine Reference Generator
The IC has a versatile low frequency sinewave reference
generator with low harmonic distortion and good frequency accuracy. In its intended mode as shown in Fig.
5, the reference generator will take an input from a
32kHz crystal (connected between XTAL1 and XTAL2)
and generate a sine-wave at 20Hz, 25Hz or 50Hz based
on the programming of pins FS0 and FS1 (See Table 2).
If the crystal frequency is changed, the output frequencies will be appropriately shifted. C-2 type Quartz crystals
(Epson makes available through DigiKey) are recommended for this application. If the frequency accuracy is
not a major concern, the more common and less expensive clock crystal (C-type) at 32.768kHz can be used with
a minor output frequency offset (20.5Hz instead of 20Hz).
Additionally, the XTAL1 input can be clocked at a desired
frequency to get a different set of output frequencies at
the sine-wave output (with divide ratios of 1600, 1280
and 640). The sine-wave output is centered around an internal reference of 3V. A capacitor from SINREF to GND
helps provide smoothing of the sine wave reference.
Recommended value is at least 0.01µF and maximum of
0.1µF. When FS0 and FS1 are both 1 (high), the sine reference is disabled and external sine-wave can be fed
into the SINREF pin. This signal should have the same
DC offset as the internal sine-wave (3V).
–
(1)
R13
R13
• VB –
• VAC
R14
R15
In order to nullify the effect of VCM on this value, the ratio
of R26 to R14 should be made 1.5. With this ratio, the
equation becomes:
VOUT1 = VCM –
R13
R13
• VB –
• VAC
R15
R14
(2)
VOUT1 is the reference voltage that the second amplifier
(AMP2) uses to program the output voltage. Assuming
that Z4 is high DC impedance, the output voltage is derived by summing the currents into pin 18. The output is
given as:
R10 R10 

VO =  1 +
+
 • VCM
R27 R12 

–
(3)
R10
R10
• REF –
• VOUT1
R27
R12
Again, if the ratio of R27 to R10 is made 1.5, the effect of
VCM is nullified and the output voltage becomes (after
substituting for VOUT1):
VO =
Reference and Error Amplifier
The recommended circuit connections for these circuits
are shown in Fig. 6. The sine-wave is added to a DC offset to create the composite reference signal for the error
amplifier. The DC reference can vary over a wide range.
For pure AC outputs it is zero, while in many common
applications, it is the talk battery voltage (–48V). The
UCC3750 accomplishes this task by summing the two
signals weighted by resisting R14 and R15. The output of
AMP1 also helps determine the mode of the circuit.
R10 • R13
R10 • R13
• VAC
• VB +
R12 • R15
R12 • R14
(4)
From equation 4, it can be seen that if the output voltage
DC value has to track VB directly, the following condition
should be forced:
R10 • R13 = R12 • R14
(5)
However, in some cases, this becomes impractical due
to large AC gain required form VAC to VO. Only a small
part of the gain can be accommodated in the first amplifier stage due to its output voltage limitations. As a result,
the required resistance values become very high. This
Referring to Fig. 6, the output of AMP1 is given by :
UDG-96166-1
UDG-96167-1
Figure 5. Sine-wave generator.
Figure 6. Error amplifier setup.
8
UCC2750
UCC3750
APPLICATION INFORMATION (cont.)
ulation turns on the PWM signal when the ramp signal
falls below MAG on the falling slope and turns it off at the
end of the clock cycle. This technique enables synchronized turn-on of the rectifier switches immediately after
the PWM pulse is turned off. The triangular nature of the
ramp ensures that the maximum duty cycle of the PWM
output is 50%, providing inherent current limiting.
problem is only manifested for high values of VB (e.g.
48V) and can be alleviated by using a fraction of the required DC offset as the VB input and regaining the offset
with resistive ratios.
The error amplifier compares the reference signal with
the output voltage by way of weighted sum at its inverting input. The error signal is further processed to separate its polarity and magnitude. An absolute value circuit
(precision full-wave rectifier) is used to get the magnitude
information. The polarity is used along with the reference
signal polarity to determine the mode information. The
absolute value circuit provides phase inversion when appropriate for modes 2 and 3 to maintain the correct loop
gain polarity. While the output of the error amplifier
swings around 3V, the full-wave rectifier output (MAG)
converts it into a signal above 3V. This signal is compared to the oscillator ramp to generate the PWM output.
Control Logic and Outputs
The PWM signal is processed through control logic which
takes into account the operating mode and output polarity to determine which output to modulate. The logic table
for the outputs is given in Table 2. For example, assume
that the reference signal is in the first quadrant (positive
and increasing). The output will lag the reference by a
certain delay and hence the error amp output will be positive, resulting in SIGN = 0. The logic table indicates that
GD1 is modulated during this phase allowing power
transfer to increase the output voltage to keep up with
the reference. Increasing error (MAG) will result in larger
duty cycle and enable the output to increase and catch
up with the reference. If the output becomes higher than
the reference (as is likely in the second quadrant when
the reference is dropping), the SIGN becomes 1 and
GD3 is modulated to decrease the output level by transferring power to the input. At the boundary of the first and
second quadrant, there may be some switching back and
forth between modes as the reference slope crosses
through zero. Some of this switching can be eliminated
by judicious selection of error amplifier filtering and compensation components. In the first quadrant, when PWM
is applied to Q1, Q2 is turned on in the rectifier mode by
the clock signal to allow the flyback transformer flux to
Oscillator and PWM Comparator
The UCC3750 has an internal oscillator capable of high
frequency (>250kHz) operation. A resistor on the RT pin
programs the current that charges and discharges CT,
resulting in a triangular ramp waveform. Fig 7. shows the
oscillator hook-up circuit. The ramp peak and valley are
4.75V and 3V respectively. The nominal frequency is
given by:
fOSC =
1
1.17 • RT • CT
The ramp waveform and the rectified output of the error
amplifier are compared by the PWM comparator to generate the PWM signal. The PWM action is disabled on
the positive slope of the ramp signal. Leading edge mod-
3V
RT
RT
24
4.75V
IR
R
IR
Q
3.0V
S
CT
CT
23
IR
UDG-99077
Figure 7. Oscillator setup.
9
UCC2750
UCC3750
APPLICATION INFORMATION (cont.)
RSENSE
11
OUTDC
R5
R6
12
TO
PWM
NEGDC
VCM
4
DC
UDG-96170-1
Figure 8. Current limiting.
Figure 9. Charge pump circuits.
reset (and to transfer power to the output). Operation in
quadrants 3 and 4 is symmetrical to the first two quadrants with Q2 and Q3 interchanged. Note that the output
signal for Q2 is logically inverted to allow for driving the
p-channel switch. An n-channel switch can also be used
for Q2, but the drive circuit must be transformer isolated
and the polarity inverted. The outputs are designed for
high peak current drive and low internal impedance. In
isolated systems, GD1 must be coupled to Q1 using a
gate-drive transformer.
Even though the DC current is typically sensed in the
secondary, the currentl limit is applied fo the active PWM
switch at the time. For example, if Q1 is the PWM switch
and DCLIM is activated, the UCC3750 will prevent
trun-on for Q1 during the negative slope of the ramp (Fig.
2). The DC limit is functional on a cycle-by-cycle basis.
Charge Pump and Reference
The UCC3750 is designed to work on the secondary side
of an isolated power supply. It requires a 5V power supply with respect to its GND pin to operate. Note that the
GND pin of the IC is also the reference point of the ring
signal that is generated by the converter. If the converter
output is connected in series with any other voltage, it
should be ensured that the available supply voltage is
referenced to the converter output return. The IC along
with its associated charge pump components shown in
Fig. 9 generates all the other voltages the system requires. The UCC3750 typically requires about 5mA to operate without any loads on the drive outputs. The charge
pump capacitor should be large enough to keep the VCP
fairly constant when driving Q1-Q3 in the converter.
DC Current Limit
The DC current limit function provides protection against
short circuit conditions by limiting the maximum current
level and shutting off the PWM function when the limit
point is reached.
The DC limit is activated when DC out is below 0.5 VCM
or above 1.5 • VCM. The DC current limit can be programmed by setting:
R5
= 3.
R6
With this ratio, a symmetric DC limit with thresholds of
±0.5V is obtained. For other ratios, the positive and negative voltage thresholds for current sense signal are
given by:
VSENSE (NEG) =
VCM  5R6 
•  1
4
R5 

140
80
MAGNITUDE (dB)
VCM  R6 
•  1
4
 R5 
160
100
MAG.
120
60
100
40
80
PHASE
60
20
40
0
20
-20
1
UNITRODE CORPORATION
7 CONTINENTAL BLVD. • MERRIMACK, NH 03054
TEL. (603) 424-2410 FAX (603) 424-3460
10
100
100
1000
10k
10000
100k 100000
1M
100000
0
FREQUENCY (Hz)
0
10M
1E+07
Figure 10. Frequency response to error amplifiers.
10
PHASE (Degree)
VSENSE (POS) =
180
120
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  2000, Texas Instruments Incorporated