OPI-110 Series This component is RoHS compliant Pb Optically Coupled Isolators ATEX and IECEx CERTIFIED The OPI-110, A/B/C and D are a family of optically coupled isolators, each consisting of a infrared light emitting diode, coupled to an NPN silicon phototransistor sealed in an injection moulded plastic housing. This series is designed for applications requiring high voltage isolation between input and output. • All electrical parameters are 100% tested by manufacturing. • Specifications are guaranteed to a 0.65% AQL. • 10 KV electrical rating • High current transfer ratio - 100% min @ 1mA If. Certificate No.- IECEx BAS 06.0021U/4 Certificate No. - BAS01ATEX1278U/5 Confirmed conform to:IEC 60079-0:2011Edition 6 IEC 60079-11:2011Edition 6 IEC 60079-26:2006 Edition 2 Conditions of use apply:- See Schedule of limitations on certificate / Details repeated on Page 2 of this datasheet. Confirmed conform to:EN60079-0:2012 EN60079-11:2012 EN60079-26:2007 Conditions of use apply:- See ‘Schedule of limitations’ on certificate / Details repeated on Page 2 of this datasheet. MECHANICAL DATA Notch Indicates Pin 1 13.9 12.7 5.84 5.59 (1) (4) (2) (3) 2.54 0.5 Square 6.6 6.1 7.62 Min (1) (4) (2) (3) BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR, LANARKSHIRE, ML12 6FX 1/4 Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] ISS O 24.01.14 OPI110 SERIES This component is RoHS compliant Pb ABSOLUTE MAXIMUM RATINGS (25OC unless otherwise noted) INPUT DIODE FORWARD DC CURRENT REVERSE DC VOLTAGE POWER DISSIPATION 50mA 2V 100mW (3) OUTPUT PHOTOTRANSISTOR COLLECTOR-EMITTER VOLTAGE EMITTER-COLLECTOR VOLTAGE POWER DISSIPATION 30 V 5V 100 mW (4) OPERATING TEMP -40OC TO +85OC STORAGE TEMP -40OC TO +85OC INPUT-TO-OUTPUT ISOLATION VOLTAGE LEAD S0LDERING TEMP (2) (1.6mm) from case for +10KV DC (1) NOTES 1- Measured with input diode leads shorted together and output leads shorted together. 2- RMA Flux is recommended. Duration can be extened to 10 sec. max. when flow soldering. 3- Derate linearly 1.33 mW/ C above 25 C 4- Derate linearly 1.33 mW/ C above 25 C Whilst the devices are capable of operating continually at the noted elevated temperatures users should be aware of the possibility of a reduction in CTR over long periods at high temperatures & currents. 240OC 5sec with soldering iron) SCHEDULE OF LIMITATIONS EC TYPE EXAMINATION CERTIFICATE No. BAS01ATEX1278U/5 SCHEDULE OF LIMITATIONS 28th September 2012 1 - The Opto Isolator must be mounted on a p.c.b. having a CTI of at least 175 such that creepage and clearance distances are not impaired. i.e.:- on an uncoated printed circuit board that maintains at least 10mm in air. 2 - The Opto Isolator may be used to provide isolation between either:(i) A non-intrinsically safe circuit and an intrinsically safe circuit, (Non IS:IS), where the IS circuit voltage is not greater than 75 Volts peak or d.c.. OR (ii) Two intrinsically safe circuits (IS:IS), where the sum of the two circuit voltages is not greater than 375 Volts peak or d.c.. 3 - The Opto Isolator must be installed such that the connection pins are provided with a degree of protection of at least IP20 where gasses and vapours may be present. If the Opto Isolator is to be installed where dusts represent a hazard, then it must be provided with a degree of protection of at least IP54 and the overall apparatus must be appropriately certified for the requirements for Dusts. 4 - The Opto Isolator must be installed with external power limiting components as specified in:- EN60079-11:2012, Clause 8.9.2. CERTIFICATE No.:- IECEx BAS 06.0021U SCHEDULE OF LIMITATIONS Date of Issue:- 2012-10-02 ISSUE No.: 4 1. When used in intrinsically safe apparatus it will be necessary to determine a surface temperature classification for the opto-isolator:- 2. The Opto Isolator must be mounted on a printed circuit board such that creepage and clearance distances are not impaired. 3. The Opto Coupler must be installed such that the connection pins are provided with a degree of protection of IP20 where gasses and vapours may be present. If the Opto Coupler is to be installed within apparatus where flammable dusts represent the hazard then it must be provided with a degree of protection of IP54 and the apparatus must be appropriately certified for dust hazards. 5 The Opto Isolator must be installed with external power limiting components as specified in:IEC60079-11:2011 Ed 6, Clause 8.9.2. BEDFORD OPTO TECHNOLOGY LTD 1BIGGAR BUSINESS PARK, BIGGAR, LANARKSHIRE, ML12 6FX 2/4 Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 ISS O 24.01.14 Website: bot.co.uk E-mail: [email protected] OPI110 SERIES This component is RoHS compliant O OPTO ELECTRONIC DATA (TA = 25 C) PARAMETER SYMBOL MIN TYP Pb MAX UNITS TEST CONDISTIONS INPUT DIODE Forward Voltage VF 1.5 V If = 20mA Reverse Current IR 100 uA Vr = 2V OUTPUT PHOTOTRANSISTOR Collector-Emitter Breakdown Voltage V(BR)CEO 30 V Ic = 1mA If = 0 Emitter-Collector Breakdown Voltage V(BR)ECO 5 V Ie = 100uA nA Vce = 10V Collector-Emitter Dark Current 100 ICEO COUPLED CHARACTERISTICS DC Current transfer ratio IC/IF OPI 110A 25 % If=10mA, Vce=5V OPI 110B 50 % If=10mA, Vce=5V OPI 110C 100 % If=10mA, Vce=5V OPI 110D 100 % If=1mA, Vce=5V 10 KV See Note (1) V If=10mA, Ic=1.6mA Isolation Voltage Collector-emitter saturation voltage VISO 0.4 VCE(SAT) Input-output capacitance Cio 0.06 pF Turn-on time t on 5 uS Ic=10mA, Vcc=10V, RL=100ohm Turn-off time t off 5 uS Ic=10mA, Vcc=10V, RL=100ohm NOTE: Measured with input diode leads shorted together and output leads shorted together. (Sample testing only). BEDFORDOPTO TECHNOLOGY LTD 1 BIGGAR BUSINESS PARK, BIGGAR,LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 3/4 Website: bot.co.uk E-mail: [email protected] ISS O 24.01.14 OPI110 SERIES CONFORMITY STATEMENT OPI110 SERIES Manufacturer:- BEDFORD OPTO TECHNOLOGY LTD Address:1 Biggar Business Park, Market Road, Biggar, Lanarkshire, ML12 6FX, Scotland Directive 94/9/EC EC-Type Examination Certificate:BAS01ATEX1278U – Latest supplement BAS01ATEX1278U/5 issued Sept. 2012 Provisions of the Directive fulfilled by the component:Ex ia IIC Ga (-40°C ≤ Ta ≤ +85°C) II 1 GD Ex ia IIIC Da (-40°C ≤ Ta ≤ +85°C) Notified Body for EC-Type Examination & Production:- BASEEFA Ltd. – No.1180 BASEEFA Ltd. Rockhead Business Park, Staden Lane, Tel:- +44 (0)1298 766600 Buxton, Fax:- +44 (0)1298 766601 Derbyshire SK17 9RZ, e-mail:- [email protected] England Harmonised Standards used:EN60079-0:2012 EN60079-11:2012 EN60079-26:2007 Other Standards used:- This component is RoHS compliant Pb On Behalf of Bedford Opto Technology Ltd., I declare that, the date the component accompanied by this statement is placed on the market, the component conforms with all technical and regulatory requirements of the ATEX Directive 94/9/EC and the RoHS Directive 2011/65/EU. _________________________________ Mr R.W.Stott Managing Director pp:- 4/4 ISS O 24.01.14