This component is RoHS compliant OPI1264 Series Optically Coupled Isolators Pb ATEX &IECEx CERTIFIED The OPI1264A/B/C/D are a family of optically coupled isolators,each consisting of a infrared light emitting diode, coupled to an NPN silicon phototransistor sealed in an injection moulded plastic housing.This series is designed for applications requiring high voltage isolation between input and output. All electrical parameters are 100% tested by manufacturing. Specifications are guaranteed to a 0.65% AQL x 10KV electrical rating x High current transfer ratio-100%min @1mA CERTIFICATE No. IECEx BAS 06.0021U/3 CERTIFICATE No. BAS01ATEX1278U/4 Confirmed conform to:IEC 60079-0:2007 Edition 5 IEC 60079-11:2006 Edition 5 IEC 60097-26:2006 Edition 2 IEC 61241-0:2004 Edition 1 IEC 61241-11:2005 Edition 1 Conditions of use apply:- See ‘Schedule of limitations’ on certificate / information on Page 2 of this datasheet Confirmed conform to:EN60079-0:2009 EN61241-0:2006 EN60079-11:2007 EN61241-11:2006 EN60079-26:2007 Conditions of use apply:- See ‘Schedule of limitations’ on certificate / Information repeated on Page 2 of this datasheet MECHANICAL DATA 13.9 12.7 7.62 min 5.84 5.59 LED Anode Polarity(Pin1) Marking Slot (1) (4) 2.54 (3) (2) Ø6.6 6.1 (1) (4) (2) (3) BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR,LANARKSHIRE ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] 1/4 Iss K 24.04.12 OPI1264 Series This component is RoHS compliant ABSOLUTE MAXIMUM RATINGS (25 qC unless otherwise noted) INPUT DIODE FORWARD DC CURRENT REVERSE DC VOLTAGE POWER DISSIPATION 50mA (3) 2V 100mW (4) OUTPUT PHOTOTRANSISTOR COLLECTOR-EMITTER VOLTAGE EMITTER-COLLECTOR VOLTAGE POWER DISSIPATION 30 V 5V 100 mW (5) OPERATING TEMP -40OC TO +85OC STORAGE TEMP -40OC TO +85OC +10KV DC (1) INPUT-TO-OUTPUT ISOLATION VOLTAGE LEAD S0LDERING TEMP (2) 1.6mm from case for 5sec with 240OC Pb NOTES 1 Measured with input diode leads shorted together and output leads shorted together. 2 RMA Flux is recommended. Duration can be extended to 10 sec. max. when flow soldering. 3 Derate linearly 0.73 mA/OC above 25OC 4 Derate linearly 1.67 mW/OC above 25OC 5 Derate linearly 1.67 mW/OC above 25OC soldering iron Whilst the devices are capable of operating continually at the noted elevated temperatures users should be aware of the possibility of a reduction in CTR over long periods at high temperatures & currents. EC TYPE EXAMINATION CERTIFICATE No. BAS01ATEX1278U SCHEDULE OF LIMITATIONS 21st August 2001 1-The Opto-isolator must be mounted on a printed circuit board with of at least 175 such that creepage and clearance distances are not impaired. i.e.:- on an uncoated printed circuit board that maintains at least 10mm in air. 2-The Opto-isolator may be used to provide isolation between either:(i) A non-intrinsically safe circuit and an intrinsically safe circuit, (Non IS:IS), where the IS circuit voltage is not greater than 75 Volts peak or d.c.. (ii) Two intrinsically safe circuits (IS:IS), where the sum of the two circuit voltages is not greater than 375 Volts peak or d.c.. 3-The Opto-isolator must be installed such that the connection pins are provided with a degree of protection of at least IP20 where gasses and vapours may be present. If the Opto-isolator is to be installed within apparatus where flammable dusts represent a hazard then the overall apparatus must be appropriately certified, (e.g. EN 50281-1-1). SUPPLEMENTARY EC-TYPE CERTIFICATE No. BAS01ATEX1278U/2 SCHEDULE OF LIMITATIONS Issued 30th October 2007 For all further applications of the Opto Isolators OPI110, OPI1000, OPI1000L and OPI1264, the Schedule of Limitations No. 3 is modified to take account of the more restrictive requirements of the Standards where DUST forms the hazard. The Opto Isolators OPI110, OPI1000, OPI1000L and OPI1264 must be installed such that the connection pins are provided with a degree of protection of at least IP20 where gasses and vapours may be present. If the Opto Isolators are to be installed where dusts represent a hazard, then they must be provided with a degree of protection of at least IP54 and the overall apparatus must be appropriately certified to the dust Standards, EN 61241-0:2006 and EN 61241-11:2006. CERTIFICATE No.:- IECEx BAS 06.0021U SCHEDULE OF LIMITATIONS Date of Issue:- 2011-12-13 ISSUE No.:- 3 1. When used in intrinsically safe apparatus it will be necessary to determine a surface temperature classification for the opto-isolator:- 2. 3. The opto-isolator must be mounted on a printed circuit board such that creepage and clearance distances are not impaired. The opto couplers must be installed such that the connection pins are provided with a degree of protection of IP20 where gasses and vapours may be present. If the opto couplers are to be installed within apparatus where flammable dusts represent the hazard then they must be provided with a degree of protection of IP54 and the apparatus must be appropriately certified for dust hazards. BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR,LANARKSHIRE ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] 2/4 Iss K 24.04.12 OPI1264 Series This component is RoHS compliant OPTO ELECTRONIC DATA (TA = 25OC) PARAMETER SYMBOL MIN TYP MAX UNITS TEST CONDISTIONS Pb INPUT DIODE Forward Voltage VF 1.5 V If = 20mA Reverse Current IR 100 A Vr = 2V OUTPUT PHOTOTRANSISTOR Collector-Emitter Breakdown Voltage V(BR)CEO 30 V Ic = 1mA If = 0 Emitter-Collector Breakdown Voltage V(BR)ECO 5 V Ie = 100A nA Vce = 10V Collector-Emitter Dark Current 100 ICEO COUPLED CHARACTERISTICS DC Current transfer ratio IC/IF OPI1264A 25 % If=10mA Vce=5V OPI1264B 50 % If=10mA Vce=5V OPI1264C 100 % If=10mA Vce=5V OPI1264D 100 % If=1mA, Vce=5V 10 KV See Note V If=10mA, Ic=1.6mA VISO Isolation Voltage Collector-emitter saturation voltage 0.4 VCE(SAT) Turn-on time t on 5 S Ic=10mA, Vcc=10V, RL=100ohm Turn-off time t off 5 S Ic=10mA, Vcc=10V, RL=100ohm NOTE: Measured with input diode leads shorted together and output leads shorted together. (Sample testing only). BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR,LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] 3/4 Iss K 24.04.12 OPI1264 Series CONFORMITY STATEMENT OPI1264 SERIES This component is RoHS compliant Pb Manufacturer:- BEDFORD OPTO TECHNOLOGY LTD Address:1 Biggar Business Park, Market Road, Biggar, Lanarkshire, ML12 6FX, Scotland Directive 94/9/EC EC-Type Examination Certificate:BAS01ATEX1278U –Latest supplement BAS01ATEX1278U/4 issued Dec. 2011 Provisions of the Directive fulfilled by the component:Ex ia IIC Ga (-40°C Ta +85°C) II 1 GD Ex ia IIIC Da (-40°C Ta +85°C) Notified Body for EC-Type Examination & Production:- BASEEFA Ltd. – No. 1180 BASEEFA Ltd. Rockhead Business Park, Staden Lane, Tel:- +44 (0)1298 766600 Buxton, Fax:- +44 (0)1298 766601 Derbyshire SK17 9RZ, e-mail:- [email protected] England Harmonised Standards used:EN60079-0:2009 EN61241-0:2006 EN60079-11:2007 EN61241-11:2006 EN60079-26:2006 Other Standards used:- On Behalf of Bedford Opto Technology Ltd., I declare that, the date the component accompanied by this statement is placed on the market, the component conforms with all technical and regulatory rerquirements of the ATEX Directive 94/9/EC. _________________________________ Mr R.W.Stott Managing Director PP- 4/4 Iss K 24.04.12