OPI 1000L Series Optically Coupled Isolators Surface Mount Low Profile These components are RoHS compliant ATEX & IECEx CERTIFIED Pb The OPI 1000L A through E are a series of Optically Coupled Isolators each consisting of a Infrared emitter coupled to a silicon photo transistor. The series is designed for applications requiring high voltage isolation between input & output. · Surface Mount configuration in Tape & Reel · High Current Transfer ratio– 40% min @ 1mA If · Low Profile · 10KV isolation CERTIFICATE No. IECEx BAS 06.0021U/4 CERTIFICATE No. - BAS01ATEX1278U/5 Confirmed conform to:IEC 60079-0:2011 Edition 6 IEC 60079-11:2011 Edition 6 IEC 60079-26:2006 Edition 2 Conditions of use apply:- See Schedule of limitations on certificate / Details repeated on Page 5 of this datasheet. Confirmed conform to:EN60079-0:2012 EN60079-11:2012 EN60079-26:2007 Conditions of use apply:- See ‘Schedule of limitations’ on certificate / Details repeated on Page 5 of this datasheet. MECHANICAL DATA 2.0 14 +0.2 0 2.0 6 +0.2 0 1.0 1.0 Min Wall 2.55/2.50 5.1+0.1-0.0 7.0 max 0.5+/-0.1 1.0 1.27 2.5 2.54 K An C E 0.5 Square BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR, LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] 1/6 Iss P 20.10.12 OPI 1000L Series This component is RoHS compliant Pb ABSOLUTE MAXIMUM RATINGS (25OC unless otherwise noted) INPUT DIODE FORWARD DC CURRENT REVERSE DC VOLTAGE POWER DISSIPATION 100mA 5 Volts 165mW (ii) OUTPUT TRANSISTOR COLLECTOR-EMITTER VOLTAGE COLLECTOR CURRENT POWER DISSIPATION 35 Volts 15 mA 165mW (iii) OPERATING TEMP -40OC TO +85OC STORAGE TEMP -40OC TO +85OC INPUT-TO-OUTPUT ISOLATION VOLTAGE + 10KV DC (i) Notes i) ii) iii) Measured with the input leads and output leads shorted together for one min. Thermal resistance 375 K/W Thermal resistance 450 K/W Whilst the devices are capable of operating continually at the noted elevated temperatures users should be aware of the possibility of a reduction in CTR over long periods at high temperatures & currents. RECOMMENDED FOOTPRINT 18 .7 0 12 .2 0 3.68 1.32 0.5 2.64 15.64 PAD CENTRES Packing Waffle Trays - 100 per tray 290mm x 200mm. Tape & Reel - 400 Devices per 13” Diam Reel with 7” HuB 32mm Wide tape. BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR, LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] 2/6 Iss P 20.10.12 OPI 1000L Series ADVISED SOLDERING CONDITIONS These components are RoHS compliant Pb BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR, LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] 3/6 Iss P 20.10.12 OPI 1000L Series These components are RoHS compliant Pb OPTO ELECTRONIC DATA (TA = 25OC) PARAMETER SYMBOL MIN TYP MAX UNITS TEST CONDITIONS Forward Voltage VF - - 1.3 V If = 20mA Reverse Voltage VR 5.0 - - V Ir = 100uA BVceo 35 - - V Ic = 10 uA Iceo OPI1000lE OPI1000lA to D - 10 nA Vce = 30 V - 100 nA Vce = 10 V 5.0 - - V Ie = 100uA INPUT DIODE OUTPUT TRANSISTOR Collector-Emitter Breakdown Voltage Collector-Emitter Leakage Current Emitter-Collector Breakdown BVeco COUPLED PAIR DC Current Transfer Ratio IC/IF OPI 1000L A - 25 - - % If = 10 mA Vce = 5 V OPI 1000L B - 50 - - % If = 10 mA Vce = 5 V OPI 1000L C - 100 - - % If = 10 mA Vce = 5 V OPI 1000L E - 40 - - % If = 1mA Vce = 5 V VISO 10 - - KV - VCE(SAT) - - 0.4 V If = 10 mA, Ic=1.6mA Turn-on time t on - 8 - uS Ic=2mA Turn-off time t off - 8 - uS Vcc = 5V RL = 100ohm Isolation Voltage Collector-emitter saturation Voltage BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR, LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] 4/6 Iss P 20.10.12 OPI 1000L Series These components are RoHS compliant Pb SCHEDULE OF LIMITATIONS EC TYPE EXAMINATION CERTIFICATE No. BAS01ATEX1278U/5 SCHEDULE OF LIMITATIONS 28th September 2012 1 - The Opto Isolator must be mounted on a p.c.b. having a CTI of at least 175 such that creepage and clearance distances are not impaired. i.e.:- on an uncoated printed circuit board that maintains at least 10mm in air. 2 - The Opto Isolator may be used to provide isolation between either:(i) A non-intrinsically safe circuit and an intrinsically safe circuit, (Non IS:IS), where the IS circuit voltage is not greater than 75 Volts peak or d.c.. OR (ii) Two intrinsically safe circuits (IS:IS), where the sum of the two circuit voltages is not greater than 375 Volts peak or d.c.. 3 - The Opto Isolator must be installed such that the connection pins are provided with a degree of protection of at least IP20 where gasses and vapours may be present. If the Opto Isolator is to be installed where dusts represent a hazard, then it must be provided with a degree of protection of at least IP54 and the overall apparatus must be Appropriately certified for the requirements for Dusts. 4 - The Opto Isolator must be installed with external power limiting components as specified in:EN60079-11:2012, Clause 8.9.2. CERTIFICATE No.:- IECEx BAS 06.0021U SCHEDULE OF LIMITATIONS Date of Issue:- 2012-10-02 ISSUE No.: 4 1. When used in intrinsically safe apparatus it will be necessary to determine a surface temperature classification for the opto-isolator:- 2. The Opto Isolator must be mounted on a printed circuit board such that creepage and clearance distances are not impaired. 3. The Opto Coupler must be installed such that the connection pins are provided with a degree of protection of IP20 where gasses and vapours may be present. If the Opto Coupler is to be installed within apparatus where flammable dusts represent the hazard then it must be provided with a degree of protection of IP54 and the apparatus must be appropriately certified for dust hazards. 5 The Opto Isolator must be installed with external power limiting components as specified in:IEC60079-11:2011 Ed 6, Clause 8.9.2. BEDFORD OPTO TECHNOLOGY LTD 1,BIGGAR BUSINESS PARK, BIGGAR, LANARKSHIRE, ML12 6FX Tel: +44 (0) 1899 221221 Fax: +44 (0) 1899 221009 Website: bot.co.uk E-mail: [email protected] 5/6 Iss P 20.10.12 OPI 1000L Series CONFORMITY STATEMENT OPI1000L SERIES This component is RoHS compliant Pb Manufacturer:- BEDFORD OPTO TECHNOLOGY LTD Address:1 Biggar Business Park, Market Road, Biggar, Lanarkshire, ML12 6FX, Scotland. Directive 94/9/EC EC-Type Examination Certificate:BAS01ATEX1278U – Latest supplement BAS01ATEX1278U/5 issued Sept. 2012 Provisions of the Directive fulfilled by the component:Ex ia IIC Ga (-40°C ≤ Ta ≤ +85°C) II 1 GD Ex ia IIIC Da (-40°C ≤ Ta ≤ +85°C) Notified Body for EC-Type Examination & Production:- BASEEFA Ltd. – No.1180 BASEEFA Ltd. Rockhead Business Park, Staden Lane, Tel:- +44 (0)1298 766600 Buxton, Fax:- +44 (0)1298 766601 Derbyshire SK17 9RZ, e-mail:- [email protected] England Harmonised Standards used:EN60079-0:2012 EN60079-11:2012 EN60079-26:2007 Other Standards used:- On Behalf of Bedford Opto Technology Ltd., I declare that, the date the component accompanied by this statement is placed on the market, the component conforms with all technical and regulatory requirements of the ATEX Directive 94/9/EC and the RoHS Dirtective 2011/65/EU. _________________________________ Mr R.W.Stott Managing Director PP- 6/6 Iss P 20.10.12