ICS843002I-01 Integrated Circuit Systems, Inc. FEMTOCLOCKS™ CRYSTAL-TO3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER GENERAL DESCRIPTION FEATURES The ICS843002I-01 is a 2 output LVPECL synthesizer optimized to generate Ethernet HiPerClockS™ reference clock frequencies and is a member of the HiPerClocks TM family of high performance clock solutions from ICS. Using a 25MHz 18pF parallel resonant crystal, the following frequencies can be generated based on the 2 frequency select pins (F_SEL[1:0]): 156.25MHz, 125MHz, and 62.5MHz. The ICS843002I-01 uses ICS’ FemtoClock TM low phase noise VCO technology and can achieve 1ps or lower typical rms phase jitter, easily meeting Ethernet jitter requirements. The ICS843002I-01 is packaged in a small 20-pin TSSOP package. • Two 3.3V or 2.5V LVPECL outputs ICS • Selectable crystal oscillator interface or LVCMOS/LVTTL single-ended input • Supports the following output frequencies: 156.25MHz, 125MHz and 62.5MHz • VCO range: 560MHz - 680MHz • RMS phase jitter @ 156.25MHz, using a 25MHz crystal (1.875MHz-20MHz): 0.55ps (typical) • Output skew: 30ps (maximum) • Supply Voltage Modes Core/Outputs 3.3/3.3 2.5/2.5 • -40°C to 85°C ambient operating temperature • Available in both standard and lead-free RoHS-compliant packages PIN ASSIGNMENT FREQUENCY SELECT FUNCTION TABLE Inputs M Divider F_SEL1 F_SEL0 Value 0 0 25 N Divider Value 4 nc VCCO Q0 nQ0 MR nPLL_SEL nc VCCA F_SEL0 VCC Output Frequency (25MHz Ref.) 156.25 (default) 0 1 25 5 125 1 0 25 10 62.5 1 1 25 5 12 5 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 VCCO Q1 nQ1 VEE VCC nXTAL_SEL REF_CLK XTAL_IN XTAL_OUT F_SEL1 ICS843002I-01 20-Lead TSSOP 6.5mm x 4.4mm x 0.92mm package body G Package Q0 Top View BLOCK DIAGRAM F_SEL[1:0] Pulldown 2 nPLL_SEL Pulldown REF_CLK Pulldown F_SEL[1:0] 1 1 25MHz XTAL_IN OSC XTAL_OUT 0 Phase Detector 00 01 10 11 ÷4 (default) ÷5 ÷10 ÷5 nQ0 Q1 nQ1 VCO 625MHz 0 (w/25MHz Reference) nXTAL_SEL Pulldown M = 25 (fixed) MR Pulldown 843002AGI-01 www.icst.com/products/hiperclocks.html 1 REV. A JANUARY 6, 2006 ICS843002I-01 Integrated Circuit Systems, Inc. FEMTOCLOCKS™ CRYSTAL-TO3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER TABLE 1. PIN DESCRIPTIONS Number Name Type Description 1, 7 nc Unused 2, 20 VCCO Power 3, 4 Q0, nQ0 Ouput 5 MR Input 6 nPLL_SEL Input 8 Power Input Pulldown Frequency select pins. LVCMOS/LVTTL interface levels. Power 14 VCCA F_SEL0, F_SEL1 VCC XTAL_OUT, XTAL_IN REF_CLK Differential output pair. LVPECL interface levels. Active HIGH Master Reset. When logic HIGH, the internal dividers are reset causing the true outputs Qx to go low and the inver ted outputs nQx Pulldown to go high. When logic LOW, the internal dividers and the outputs are enabled. LVCMOS/LVTTL interface levels. Determines whether synthesizer is in PLL or bypass mode. Pulldown LVCMOS/LVTTL interface levels. Analog supply pin. 15 nXTAL_SEL Input 17 VEE Power Core supply pin. Parallel resonant crystal interface. XTAL_OUT is the output, XTAL_IN is the input. Pulldown LVCMOS/LVTTL reference clock input. Selects between crystal or REF_CLK inputs as the the PLL Reference Pulldown source. Selects XTAL inputs when LOW. Selects REF_CLK when HIGH. LVCMOS/LVTTL interface levels. Negative supply pins. 18, 19 nQ1, Q1 Output 9, 11 10, 16 12, 13 Input Input No connect. Output supply pins. Differential output pair. LVPECL interface levels. NOTE: Pulldown refer to internal input resistors. See Table 2, Pin Characteristics, for typical values. TABLE 2. PIN CHARACTERISTICS Symbol Parameter CIN Input Capacitance 4 pF RPULLDOWN Input Pulldown Resistor 51 kΩ 843002AGI-01 Test Conditions Minimum www.icst.com/products/hiperclocks.html 2 Typical Maximum Units REV. A JANUARY 6, 2006 ICS843002I-01 Integrated Circuit Systems, Inc. FEMTOCLOCKS™ CRYSTAL-TO3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER ABSOLUTE MAXIMUM RATINGS Supply Voltage, VCC 4.6V Inputs, VI -0.5V to VCC + 0.5V Outputs, IO Continuous Current Surge Current 50mA 100mA Package Thermal Impedance, θJA 73.2°C/W (0 lfpm) Storage Temperature, TSTG -65°C to 150°C NOTE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only. Functional operation of product at these conditions or any conditions beyond those listed in the DC Characteristics or AC Characteristics is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. TABLE 3A. POWER SUPPLY DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V±10%, TA = -40°C TO 85°C Symbol Parameter Test Conditions VCC Core Supply Voltage Minimum Typical Maximum Units 2.97 3.3 3.63 V VCCA Analog Supply Voltage 2.97 3.3 3.63 V VCCO Output Supply Voltage 2.97 3.3 3.63 V IEE Power Supply Current 130 mA ICCA Analog Supply Current 13 mA TABLE 3B. POWER SUPPLY DC CHARACTERISTICS, VCC = VCCA = VCCO = 2.5V±5%, TA = -40°C TO 85°C Symbol Parameter Minimum Typical Maximum Units VCC Core Supply Voltage Test Conditions 2.375 2.5 2.625 V VCCA Analog Supply Voltage 2.375 2.5 2.625 V 2.375 2.5 VCCO Output Supply Voltage 2.625 V IEE Power Supply Current 115 mA ICCA Analog Supply Current 12 mA TABLE 3C. LVCMOS / LVTTL DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V±10% OR 2.5V±5%, TA = -40°C TO 85°C Symbol Parameter VIH Input High Voltage VIL Input Low Voltage IIH Input High Current REF_CLK, MR, nPLL_SEL, nXTAL_SEL VCC = VIN = 3.63V or 2.625V IIL Input Low Current REF_CLK, MR, nPLL_SEL, nXTAL_SEL VCC = VIN = 3.63V or 2.625V 843002AGI-01 Test Conditions Minimum Typical Maximum Units VCC = 3.3V 2 VCC + 0.3 V VCC = 2.5V 1. 7 VCC + 0.3 V VCC = 3.3V -0.3 0.8 V VCC = 2.5V -0.3 0.7 V 150 µA www.icst.com/products/hiperclocks.html 3 -5 µA REV. A JANUARY 6, 2006 ICS843002I-01 Integrated Circuit Systems, Inc. FEMTOCLOCKS™ CRYSTAL-TO3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER TABLE 3D. LVPECL DC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V±10% OR 2.5V±5%, TA = -40°C TO 85°C Symbol Parameter Maximum Units VOH Output High Voltage; NOTE 1 Test Conditions Minimum VCCO - 1.4 Typical VCCO - 0.9 V VOL Output Low Voltage; NOTE 1 VCCO - 2.0 VCCO - 1.7 V VSWING Peak-to-Peak Output Voltage Swing 0.6 1. 0 V NOTE 1: Outputs terminated with 50Ω to VCCO - 2V. TABLE 4. CRYSTAL CHARACTERISTICS Parameter Test Conditions Minimum Mode of Oscillation Typical Maximum Units Fundamental Frequency 22.4 25 27.2 MHz Equivalent Series Resistance (ESR) 50 Ω Shunt Capacitance 7 pF Drive Level 1 mW Maximum Units NOTE: Characterized using an 18pF parallel resonant crystal. TABLE 5A. AC CHARACTERISTICS, VCC = VCCA = VCCO = 3.3V±10%, TA = -40°C TO 85°C Symbol Parameter fOUT Output Frequency t sk(o) Test Conditions Minimum Typical F_SEL[1:0] = 00 140 170 MHz F_SEL[1:0] = 01 112 136 MHz F_SEL[1:0] = 10 56 68 MHz 30 ps Output Skew; NOTE 1, 2 t jit(Ø) RMS Phase Jitter ; NOTE 2, 3 tR / tF Output Rise/Fall Time 156.25MHz, (1.875MHz - 20MHz) 0.55 ps 125MHz, (1.875MHz - 20MHz) 0.60 ps 62.5MHz, (1.875MHz - 20MHz) 0.70 20% to 80% 350 odc Output Duty Cycle 48 NOTE 1: Defined as skew between outputs at the same supply voltages and with equal load conditions. Measured at the output differential cross points. NOTE 2: This parameter is defined in accordance with JEDEC Standard 65. NOTE 3: Measured using cr ystal input. ps 650 ps 52 % Maximum Units TABLE 5B. AC CHARACTERISTICS, VCC = VCCA = VCCO = 2.5V±5%, TA = -40°C TO 85°C Symbol Parameter fOUT Output Frequency tsk(o) Test Conditions Minimum F_SEL[1:0] = 00 140 17 0 MHz F_SEL[1:0] = 01 112 136 MHz F_SEL[1:0] = 10 56 68 MHz 30 ps Output Skew; NOTE 1, 2 t jit(Ø) RMS Phase Jitter; NOTE 2, 3 tR / tF Output Rise/Fall Time 156.25MHz, (1.875MHz - 20MHz) 0.55 ps 125MHz, (1.875MHz - 20MHz) 0.60 ps 62.5MHz, (1.875MHz - 20MHz) 20% to 80% odc Output Duty Cycle For Notes, see Table 5A above. 843002AGI-01 Typical www.icst.com/products/hiperclocks.html 4 0.74 ps 350 650 ps 48 52 % REV. A JANUARY 6, 2006 ICS843002I-01 Integrated Circuit Systems, Inc. FEMTOCLOCKS™ CRYSTAL-TO3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER TYPICAL PHASE NOISE AT 156.25MHZ @ 3.3V ➤ 0 -10 -20 10 Gigabit Ethernet Filter -30 -40 156.25MHz dBc Hz -50 RMS Phase Noise Jitter 1.875MHz to 20MHz = 0.55ps (typical) -60 -70 -90 Raw Phase Noise Data -100 ➤ NOISE POWER -80 -110 -120 -130 -140 -150 ➤ -160 -170 -180 -190 100 1k Phase Noise Result by adding 10 Gigabit Ethernet Filter to raw data 10k 100k 1M 10M 100M OFFSET FREQUENCY (HZ) 843002AGI-01 www.icst.com/products/hiperclocks.html 5 REV. A JANUARY 6, 2006 ICS843002I-01 Integrated Circuit Systems, Inc. FEMTOCLOCKS™ CRYSTAL-TO3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER PARAMETER MEASUREMENT INFORMATION 2V 2V Qx V CC , VCCA, VCCO SCOPE Qx V CC , VCCA, VCCO LVPECL SCOPE LVPECL nQx nQx VEE VEE -1.3V ± 0.33V -0.5V ± 0.125V 3.3V CORE/3.3V OUTPUT LOAD AC TEST CIRCUIT 2.5V CORE/2.5V OUTPUT LOAD AC TEST CIRCUIT nQ0, nQ1 nQx Q0,Q1 Qx t PW t nQy Qy odc = PERIOD t PW x 100% t PERIOD tsk(o) OUTPUT SKEW OUTPUT DUTY CYCLE/PULSE WIDTH/PERIOD Noise Power Phase Noise Plot 80% Phase Noise Mask 80% VSW I N G f1 Offset Frequency Clock Outputs 20% 20% f2 tR tF RMS Jitter = Area Under the Masked Phase Noise Plot RMS PHASE JITTER 843002AGI-01 OUTPUT RISE/FALL TIME www.icst.com/products/hiperclocks.html 6 REV. A JANUARY 6, 2006 ICS843002I-01 Integrated Circuit Systems, Inc. FEMTOCLOCKS™ CRYSTAL-TO3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER APPLICATION INFORMATION POWER SUPPLY FILTERING TECHNIQUES As in any high speed analog circuitry, the power supply pins are vulnerable to random noise. The ICS843002I-01 provides separate power supplies to isolate any high switching noise from the outputs to the internal PLL. VCC, VCCA, and VCCO should be individually connected to the power supply plane through vias, and bypass capacitors should be used for each pin. To achieve optimum jitter performance, power supply isolation is required. Figure 1 illustrates how a 10Ω resistor along with a 10µF and a .01μF bypass capacitor should be connected to each VCCA. 3.3V or 2.5V VCC .01μF 10Ω VCCA .01μF 10μF FIGURE 1. POWER SUPPLY FILTERING CRYSTAL INPUT INTERFACE parallel resonant crystal and were chosen to minimize the ppm error. The ICS843002I-01 has been characterized with 18pF parallel resonant crystals. The capacitor values shown in Figure 2 below were determined using a 25MHz 18pF XTAL_OUT C1 33p X1 18pF Parallel Crystal XTAL_IN C2 27p ICS843002I-01 Figure 2. CRYSTAL INPUt INTERFACE 843002AGI-01 www.icst.com/products/hiperclocks.html 7 REV. A JANUARY 6, 2006 ICS843002I-01 Integrated Circuit Systems, Inc. FEMTOCLOCKS™ CRYSTAL-TO3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER RECOMMENDATIONS FOR UNUSED INPUT AND OUTPUT PINS INPUTS: OUTPUTS: CRYSTAL INPUT: For applications not requiring the use of the crystal oscillator input, both XTAL_IN and XTAL_OUT can be left floating. Though not required, but for additional protection, a 1kΩ resistor can be tied from XTAL_IN to ground. LVPECL OUTPUT All unused LVPECL outputs can be left floating. We recommend that there is no trace attached. Both sides of the differential output pair should either be left floating or terminated. REF_CLK INPUT: For applications not requiring the use of the reference clock, it can be left floating. Though not required, but for additional protection, a 1kΩ resistor can be tied from the REF_CLK to ground. LVCMOS CONTROL PINS: All control pins have internal pull-ups or pull-downs; additional resistance is not required but can be added for additional protection. A 1kΩ resistor can be used. TERMINATION FOR 3.3V LVPECL OUTPUT outputs are designed to drive 50Ω transmission lines. Matched impedance techniques should be used to maximize operating frequency and minimize signal distortion. Figures 3A and 3B show two different layouts which are recommended only as guidelines. Other suitable clock layouts may exist and it would be recommended that the board designers simulate to guarantee compatibility across all printed circuit and clock component process variations. The clock layout topology shown below is a typical termination for LVPECL outputs. The two different layouts mentioned are recommended only as guidelines. FOUT and nFOUT are low impedance follower outputs that generate ECL/LVPECL compatible outputs. Therefore, terminating resistors (DC current path to ground) or current sources must be used for functionality. These 3.3V Zo = 50Ω 125Ω FOUT FIN Zo = 50Ω Zo = 50Ω FOUT 50Ω 1 RTT = Z ((VOH + VOL) / (VCC – 2)) – 2 o FIN 50Ω Zo = 50Ω VCC - 2V RTT 84Ω FIGURE 3A. LVPECL OUTPUT TERMINATION 843002AGI-01 125Ω 84Ω FIGURE 3B. LVPECL OUTPUT TERMINATION www.icst.com/products/hiperclocks.html 8 REV. A JANUARY 6, 2006 ICS843002I-01 Integrated Circuit Systems, Inc. TERMINATION FOR FEMTOCLOCKS™ CRYSTAL-TO3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER 2.5V LVPECL OUTPUT close to ground level. The R3 in Figure 4B can be eliminated and the termination is shown in Figure 4C. Figure 4A and Figure 4B show examples of termination for 2.5V LVPECL driver. These terminations are equivalent to terminating 50Ω to VCC - 2V. For VCCO = 2.5V, the VCCO - 2V is very 2.5V 2.5V 2.5V VCCO=2.5V VCCO=2.5V R1 250 R3 250 Zo = 50 Ohm Zo = 50 Ohm + + Zo = 50 Ohm Zo = 50 Ohm - - 2,5V LVPECL Driv er 2,5V LVPECL Driv er R2 62.5 R1 50 R4 62.5 R2 50 R3 18 FIGURE 4B. 2.5V LVPECL DRIVER TERMINATION EXAMPLE FIGURE 4A. 2.5V LVPECL DRIVER TERMINATION EXAMPLE 2.5V VCCO=2.5V Zo = 50 Ohm + Zo = 50 Ohm 2,5V LVPECL Driv er R1 50 R2 50 FIGURE 4C. 2.5V LVPECL TERMINATION EXAMPLE 843002AGI-01 www.icst.com/products/hiperclocks.html 9 REV. A JANUARY 6, 2006 ICS843002I-01 Integrated Circuit Systems, Inc. FEMTOCLOCKS™ CRYSTAL-TO3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER LAYOUT GUIDELINE Figure 5A shows a schematic example of the ICS843002I-01. An example of LVEPCL termination is shown in this schematic. Additional LVPECL termination approaches are shown in the LVPECL Termination Application Note. In this example, an 18 pF parallel resonant 26.5625MHz crystal is used. The C1=27pF and C2=33pF are recommended for frequency accuracy. For different board layout, the C1 and C2 may be slightly adjusted for optimizing frequency accuracy. 3.3V VCC VCCA R2 10 R3 133 R5 133 Zo = 50 Ohm C3 10uF C4 0.01u + VCC VCCO C6 0.1u Set Logic Input to '0' VCC RD1 Not Install - R4 82.5 ICS843002i-01 R6 82.5 VCC=3.3V F_SEL1 XTAL_OUT XTAL_IN REF_CLK nXTAL_SEL VCC VEE nQ1 Q1 VCCO RU2 Not Install To Logic Input pins U1 To Logic Input pins VCCO=3.3V Zo = 50 Ohm + 11 12 13 14 15 16 17 18 19 20 RU1 1K VCC F_SEL0 VCCA nc nPLL_SEL MR nQ0 Q0 VCCO nc Set Logic Input to '1' VCC Zo = 50 Ohm C7 0.1u 10 9 8 7 6 5 4 3 2 1 Logic Control Input Examples RD2 1K Zo = 50 Ohm VCCO C8 0.1u C2 33pF X1 25 MHz 18pF R8 50 VCC R7 50 R9 50 C9 0.1u C1 27pF Optional Termination ICS843002I-01 FIGURE 5A. ICS843002I-01 SCHEMATIC EXAMPLE PC BOARD LAYOUT EXAMPLE Figure 5B shows an example of ICS843002I-01 P.C. board layout. The crystal X1 footprint shown in this example allows installation of either surface mount HC49S or through-hole HC49 package. The footprints of other components in this example are listed in the Table 6. There should be at least one decoupling capacitor per power pin. The decoupling capacitors should be located as close as possible to the power pins. The layout assumes that the board has clean analog power ground plane. TABLE 6. FOOTPRINT TABLE Reference Size C1, C2 0402 C3 0805 C4, C5, C6, C7, C8 0603 R2 0603 NOTE: Table 6, lists component sizes shown in this layout example. FIGURE 5B. ICS843002I-01 PC BOARD LAYOUT EXAMPLE 843002AGI-01 www.icst.com/products/hiperclocks.html 10 REV. A JANUARY 6, 2006 ICS843002I-01 Integrated Circuit Systems, Inc. FEMTOCLOCKS™ CRYSTAL-TO3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER POWER CONSIDERATIONS This section provides information on power dissipation and junction temperature for the ICS843002I-01. Equations and example calculations are also provided. 1. Power Dissipation. The total power dissipation for the ICS843002I-01 is the sum of the core power plus the power dissipated in the load(s). The following is the power dissipation for VCC = 3.3V + 10% = 3.63V, which gives worst case results. NOTE: Please refer to Section 3 for details on calculating power dissipated in the load. • • Power (core)MAX = VCC_MAX * IEE_MAX = 3.63V * 130mA = 471.9mW Power (outputs)MAX = 30mW/Loaded Output pair If all outputs are loaded, the total power is 2 * 30mW = 60mW Total Power_MAX (3.63V, with all outputs switching) = 471.9mW + 60mW = 531.9mW 2. Junction Temperature. Junction temperature, Tj, is the temperature at the junction of the bond wire and bond pad and directly affects the reliability of the device. The maximum recommended junction temperature for HiPerClockSTM devices is 125°C. The equation for Tj is as follows: Tj = θJA * Pd_total + TA Tj = Junction Temperature θJA = Junction-to-Ambient Thermal Resistance Pd_total = Total Device Power Dissipation (example calculation is in section 1 above) TA = Ambient Temperature In order to calculate junction temperature, the appropriate junction-to-ambient thermal resistance θJA must be used. Assuming a moderate air flow of 200 linear feet per minute and a multi-layer board, the appropriate value is 66.6°C/W per Table 7 below. Therefore, Tj for an ambient temperature of 85°C with all outputs switching is: 85°C + 0.532W * 66.6°C/W = 120.4°C. This is below the limit of 125°C. This calculation is only an example. Tj will obviously vary depending on the number of loaded outputs, supply voltage, air flow, and the type of board (single layer or multi-layer). TABLE 7. THERMAL RESISTANCE θJA FOR 20-PIN TSSOP, FORCED CONVECTION θJA by Velocity (Linear Feet per Minute) Single-Layer PCB, JEDEC Standard Test Boards Multi-Layer PCB, JEDEC Standard Test Boards 0 200 114.5°C/W 73.2°C/W 98.0°C/W 66.6°C/W 500 88.0°C/W 63.5°C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. 843002AGI-01 www.icst.com/products/hiperclocks.html 11 REV. A JANUARY 6, 2006 ICS843002I-01 Integrated Circuit Systems, Inc. FEMTOCLOCKS™ CRYSTAL-TO3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER 3. Calculations and Equations. The purpose of this section is to derive the power dissipated into the load. LVPECL output driver circuit and termination are shown in Figure 6. VCCO Q1 VOUT RL 50 VCCO - 2V FIGURE 6. LVPECL DRIVER CIRCUIT TERMINATION AND To calculate worst case power dissipation into the load, use the following equations which assume a 50Ω load, and a termination voltage of V - 2V. CCO • For logic high, VOUT = V OH_MAX =V CCO_MAX – 0.9V (VCCO_MAX - VOH_MAX) = 0.9V • For logic low, VOUT = V OL_MAX (V CCO_MAX -V OL_MAX =V CCO_MAX – 1.7V ) = 1.7V Pd_H is power dissipation when the output drives high. Pd_L is the power dissipation when the output drives low. Pd_H = [(V OH_MAX – (V CCO_MAX - 2V))/R ] * (V CCO_MAX L -V OH_MAX ) = [(2V - (V CCO_MAX -V OH_MAX ))/R ] * (V CCO_MAX L -V OH_MAX )= [(2V - 0.9V)/50Ω] * 0.9V = 19.8mW Pd_L = [(V OL_MAX – (V CCO_MAX - 2V))/R ] * (V L CCO_MAX -V OL_MAX ) = [(2V - (V CCO_MAX -V OL_MAX ))/R ] * (V L CCO_MAX -V OL_MAX )= [(2V - 1.7V)/50Ω] * 1.7V = 10.2mW Total Power Dissipation per output pair = Pd_H + Pd_L = 30mW 843002AGI-01 www.icst.com/products/hiperclocks.html 12 REV. A JANUARY 6, 2006 ICS843002I-01 Integrated Circuit Systems, Inc. FEMTOCLOCKS™ CRYSTAL-TO3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER RELIABILITY INFORMATION TABLE 8. θJAVS. AIR FLOW TABLE FOR 20 LEAD TSSOP θJA by Velocity (Linear Feet per Minute) Single-Layer PCB, JEDEC Standard Test Boards Multi-Layer PCB, JEDEC Standard Test Boards 0 200 500 114.5°C/W 73.2°C/W 98.0°C/W 66.6°C/W 88.0°C/W 63.5°C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. TRANSISTOR COUNT The transistor count for ICS843002I-01 is: 2955 843002AGI-01 www.icst.com/products/hiperclocks.html 13 REV. A JANUARY 6, 2006 ICS843002I-01 Integrated Circuit Systems, Inc. PACKAGE OUTLINE - G SUFFIX FEMTOCLOCKS™ CRYSTAL-TO3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER FOR 20 LEAD TSSOP TABLE 9. PACKAGE DIMENSIONS Millimeters SYMBOL MIN MAX N A 20 -- 1.20 A1 0.05 0.15 A2 0.80 1.05 b 0.19 0.30 c 0.09 0.20 D 6.40 6.60 E E1 6.40 BASIC 4.30 e 4.50 0.65 BASIC L 0.45 0.75 α 0° 8° aaa -- 0.10 Reference Document: JEDEC Publication 95, MO-153 843002AGI-01 www.icst.com/products/hiperclocks.html 14 REV. A JANUARY 6, 2006 ICS843002I-01 Integrated Circuit Systems, Inc. FEMTOCLOCKS™ CRYSTAL-TO3.3V, 2.5V LVPECL FREQUENCY SYNTHESIZER TABLE 10. ORDERING INFORMATION Part/Order Number Marking Package Shipping Packaging Temperature ICS843002AGI-01 ICS43002AI01 20 Lead TSSOP tube -40°C to 85°C ICS843002AGI-01T ICS43002AI01 20 Lead TSSOP 2500 tape & reel -40°C to 85°C ICS843002AGI-01LF ICS3002AI01L 20 Lead "Lead-Free" TSSOP tube -40°C to 85°C ICS843002AGI-01LFT ICS3002AI01L 20 Lead "Lead-Free" TSSOP 2500 tape & reel -40°C to 85°C NOTE: Par ts that are ordered with an "LF" suffix to the par t number are the Pb-Free configuration and are RoHS compliant. The aforementioned trademarks, HiPerClockS and FemtoClocks are trademarks of Integrated Circuit Systems, Inc. or its subsidiaries in the United States and/or other countries. While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Incorporated (ICS) assumes no responsibility for either its use or for infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial and industrial applications. Any other applications such as those requiring high reliability or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. 843002AGI-01 www.icst.com/products/hiperclocks.html 15 REV. A JANUARY 6, 2006