TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 TRUE DIGITAL AUDIO AMPLIFIER TAS5110 PWM POWER OUTPUT STAGE FEATURES D 50-W RMS Power Into 6 Ω at 10% THD D 40-W RMS Power Into 6 Ω at 0.1% THD D THD+N < 0.09% Typical (1-kHz Input Signal) D 93-dB Dynamic Range (TDAA System) D Power Efficiency > 90% Into 6-Ω and 8-Ω Load D Low Profile, SMD 32-Pin PowerPAD Package D Self-Protecting Design D 3.3-V Digital Interface D EMI Compliant When Used With DESCRIPTION The TAS5110 is a high-performance true digital audio amplifier (TDAA) power stage, designed to drive 50 W per channel. The TAS5110 incorporates TI’s equibitt technology and is used in conjunction with a digital audio PWM processor (TAS50xx) to deliver high-power, true digital audio amplification. The efficiency of this digital amplifier can be greater than 90%, reducing the size of both the power supplies and heat sinks needed. The TAS5110 accepts a mono PWM 3.3-V input and controls the switching of an internal CMOS H-bridge. When used with the TAS50xx PWM processor, system performance of less than 0.09% THD is attainable. Over-current protection, over-temperature, and under-voltage protections are built into the TAS5110, safeguarding the H-bridge and speakers against output shorts, over-voltage conditions, and other fault conditions that could damage the system. Recommended System Design APPLICATIONS D DVD Receiver D Home Theater D Mini/Micro Component Systems D Internet Music Appliance D Car Audio Amplifiers and Head Units TYPICAL TDAA STEREO AUDIO SYSTEM Left Digital Audio • TAS3001 • DSP • SPDIF • 1394 • • • • • Volume EQ DRC Bass Treble TAS5110 L-C Filter TAS5110 L-C Filter TAS50xx Right • Serial Audio Input Port • Internal PLL • PCM–PWM Modulator • Two H-Bridge Power Devices Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD and Equibit are trademarks of Texas Instruments. Copyright 2002, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com 1 TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 terminal assignments The TAS5110 is offered in a thermally enhanced 32-pin HTSSOP surface-mount package (DAP). The DAP package has the PowerPAD on the bottom. DAP PACKAGE (TOP VIEW) PWM_AP PWM_AM ERR1 ERR0 SHUTDOWN DVDD DVSS DVSS DVSS VRFILT BIAS_A BIAS_B PWDN RESET PWM_BM PWM_BP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ordering information 2 TC 0°C to 70°C PACKAGE TAPE AND REEL TAS5110DAP TAS5110DAPR –40°C to 85°C TAS5110IDAP TAS5110IDAPR www.ti.com 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 PVDDA2 LDROUTA BOOTSTRAPA PVDDA1 PVDDA1 OUTPUTA OUTPUTA PVSS PVSS OUTPUTB OUTPUTB PVDDB1 PVDDB1 BOOTSTRAPB LDROUTB PVDDB2 TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 terminal assignments In addition to the 32-pin HTSSOP DAP package, the TAS5110 is offered in a thermally enhanced 32-pin TSSOP surface-mount package (DAD). The DAD package has the PowerPAD on top. DAD PACKAGE (TOP VIEW) PWM_BP PWM_BM RESET PWDN BIAS_B BIAS_A VRFILT DVSS DVSS DVSS DVDD SHUTDOWN ERR0 ERR1 PWM_AM PWM_AP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 PVDDB2 LDROUTB BOOTSTRAPB PVDDB1 PVDDB1 OUTPUTB OUTPUTB PVSS PVSS OUTPUTA OUTPUTA PVDDA1 PVDDA1 BOOTSTRAPA LDROUTA PVDDA2 ordering information TC 0°C to 70°C PACKAGE TAPE AND REEL TAS5110DAD TAS5110DADR –40°C to 85°C TAS5110IDAD TAS5110IDADR references TAS5000 Digital Audio PWM Processor data manual – TI Literature Number SLAS270 TAS5001 Digital Audio PWM Processor data manual – TI Literature Number SLES009 TAS5010 Digital Audio PWM Processor data manual – TI Literature Number SLAS328 TAS5012 Digital Audio PWM Processor data manual – TI Literature Number SLES006 Digital Audio Measurements – TI literature number SLAA114 PowerPAD Thermally Enhanced Package – TI literature number SLMA002 www.ti.com 3 TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 PVDDA1 PVDDA1 BOOTSTRAPA PVDDA2 LDROUTA functional block diagram 1/2 H-Bridge LDR OUTPUTA PWM_AP PWM_AM DIFF RCVR OUTPUTA Boot Strap Gate Drive PVSS BIAS_A PWDN RESET SHUTDOWN ERR1 ERR0 Control/Sense Circuit Bandgap Reference LDROUTB PVDDB2 VRFILT BOOTSTRAPB PVDDB1 1/2 H-Bridge BIAS_B PVDDB1 LDR DIFF RCVR 4 OUTPUTB Boot Strap Gate Drive OUTPUTB PVSS DVDD PWM_BP DVSS PWM_BM www.ti.com TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 suggested system block diagrams Digital Audio • USB • IEEE 1394 • SPDIF • ADC • Automotive MOST Network TAS30xx IIC Audio Control L-C Filter TAS5110 Left TAS50xx Right L-C Filter TAS5110 • Digital Parametric EQ • Serial Audio Input Port • Volume • Internal PLL • DRC • Two H-Bridges • Bass • Treble Figure 1. System #1: Stereo Configuration With a TAS3001 Digital Audio Processor CH1 TAS50xx Home Theater DVD 6-Channel Encoded Digital Audio Source 6 TI DSP • Dolby AC-3 • DTS • Volume • EQ • DRC • Bass • Treble TAS5110 L-C Filter TAS5110 L-C Filter Surround Left TAS5110 L-C Filter Surround Right TAS5110 L-C Filter Center TAS5110 L-C Filter Subwoofer Left Right CH4 CH5 TAS50xx L-C Filter CH2 CH3 TAS50xx TAS5110 CH6 Figure 2. System #3: 6-Channel Audio Playback www.ti.com 5 TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 Terminal Functions TERMINAL DAP NO. DAD NO. I/O BIAS_A 11 6 I Connect external resistor to DVSS. BIAS_B 12 5 I Connect external resistor to DVSS. BOOTSTRAPA 30 19 O Bootstrap capacitor pin for H-bridge A BOOTSTRAPB 19 30 O Bootstrap capacitor pin for H-bridge B DVDD 6 11 I 3.3-V digital voltage supply for logic DVSS 7, 8, 9 8, 9, 10 I Digital ground for logic is internally connected to PVSS. All three pins must be tied together but not connected externally to PVSS. See Figure 5. ERR1 3 14 O Error/warning report indicator. This output is open drain with internal pullup resistor. ERR0 4 13 O Error/warning report indicator. This output is open drain with internal pullup resistor. LDROUTA 31 18 O Low voltage drop-out regulator output A (not to be used to supply current to external circuitry) LDROUTB 18 31 O Low voltage drop-out regulator output B (not to be used to supply current to external circuitry) OUTPUTA 26, 27 22, 23 O H-bridge output A OUTPUTB 22, 23 26, 27 O H-bridge output B PVDDA1 28, 29 20, 21 I High voltage power supply, H-bridge A PVDDA2 32 17 I High voltage power supply for low-dropout voltage regulator A-side PVDDB1 20, 21 28, 29 I High voltage power supply, H-bridge B PVDDB2 17 32 I High voltage power supply for low-dropout voltage regulator B-side PVSS 24, 25 24, 25 I High voltage power supply ground PWDN 13 4 I Power down = 0, normal mode = 1 PWM_AM 2 15 I PWM input A(–) PWM_AP 1 16 I PWM input A(+) PWM_BP 16 1 I PWM input B(+) PWM_BM 15 2 I PWM input B(–) RESET 14 3 I Reset and mute mode = 0, normal mode = 1, when in reset mode, H-bridge MOSFETs are in low-low output state. Asserting the RESET signal low causes all fault conditions to be cleared. SHUTDOWN 5 12 O Device is in shutdown due to fault condition, normal mode = 1, shutdown = 0, when device is in shutdown mode the H-bridge MOSFETs are in low-low output state. The latched output can be cleared by asserting the RESET signal. This output is open drain with internal pullup resistor. VRFILT 10 7 O A filter capacitor must be added between VRFILT and DVSS pins. NAME DESCRIPTION NOTE: The four PWM inputs: PWM_AP, PWM_AM, PWM_BP, and PWM_BM must always be connected to the TAS50xx output pins, and never left floating. Floating PWM input pins causes an illegal PWM input state signal to be asserted. Dual pins: OUTPUTA, OUTPUTB, PVDDA1, and PVDDB1 must have both pins connected externally to the same point on the circuit board, respectively. Both PVSS pins must also be connected together externally. These multiple pins are for the high-current DMOS output devices. Failure to connect all the multiple pins to the same respective node results in excessive current flow in the internal bond wires and can cause the device to fail. All electrical characteristics are specified and measured with all of the multiple pins connected to the same node, respectively. 6 www.ti.com TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 functional description PWM H-bridge state control The digital interface control signals consists of PWM_AP, PWM_AM, PWM_BP, and PWM_BM. These signals are a complementary differential signal format for the A-side half-bridge and the B-side half-bridge. bootstrapped gate drive The TAS5110 includes two dedicated bootstrapped power supplies. A bootstrap capacitor is connected between the individual bootstrap pin and the associated output. For example, a capacitor is connected between the BOOTSTRAPA pin and OUTPUTA pin, and another capacitor is connected between the BOOTSTRAPB pin and the OUTPUTB pin. The bootstrap power supply minimizes the number of high voltage power supply levels externally supplied to the system while providing a low-noise supply level for driving the high-side N-channel DMOS transistors. low-dropout voltage regulator Two on-chip low-dropout voltage regulators (LDO) are provided to minimize the number of external power supplies needed for the system. These voltage regulators are for internal circuits only and cannot be used for external circuitry. Each LDO is dedicated to a half-bridge and its gate driver. An LDO output capacitor is connected between the individual LDO output pin and the associated output return. For example, a capacitor is connected between the LDROUTA pin and PVSS pin, and another capacitor is connected between the LDROUTB pin and PVSS pin. high-current H-bridge output stage The positive outputs of the H-bridge are the two OUTPUTA pins. The negative outputs of the H-bridge are the two OUTPUTB pins. The logic for the input command to H-bridge outputs is described in the H-bridge output mapping section below. When the TAS5110 is in the normal mode, as seen in the H-bridge output mapping tables, the outputs are decoded from the inputs. However, the TAS5110 is immediately shut down if any of the following error conditions occur: over-current, over-temperature, low regulator output voltage, or an illegal PWM input state is applied. For these conditions, the outputs are set to the appropriate disabled state as specified in the H-bridge output mapping section, and the SHUTDOWN pin is set low. H-bridge output mapping The A-side half-bridge output is designed to the following truth table: INPUTS OUTPUTS DESCRIPTION RESET PWDN PWM_AP PWM_AM SHUTDOWN X X X X 0 OUTPUTA 0 or Hi-Z† X 0 X X 1 Hi-Z 0 1 X X 1 0 Reset 1 1 0 0 0 0 Shutdown 1 1 0 1 1 0 Normal 1 1 1 0 1 1 Normal 1 1 1 1 0 0 † Output is 0 for low voltage, over temperature, and illegal input. Hi-Z is for over current. www.ti.com Shutdown Powerdown Shutdown 7 TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 H-bridge output mapping (continued) The B-side half-bridge output is designed to the following truth table: INPUTS OUTPUTS DESCRIPTION RESET PWDN PWM_BP PWM_BM SHUTDOWN X X X X 0 OUTPUTB 0 or Hi-Z† X 0 X X 1 Hi-Z Powerdown 0 1 X X 1 0 Reset 1 1 0 0 0 0 Shutdown 1 1 0 1 1 0 Normal 1 1 1 0 1 1 Normal Shutdown 1 1 1 1 0 0 † Output is 0 for low voltage, over temperature, or illegal input. Hi-Z is for over current. Shutdown control/sense circuitry The control/sense circuitry consists of the following 3.3-V logic level pins: PWDN, RESET, ERR0, ERR1, and SHUTDOWN. The active-low PWDN input pin powers down all internal circuitry and forces the H-bridge outputs to the Hi-Z state. When the PWDN pin is low, the open drain ERR0, ERR1, and SHUTDOWN pins are also disabled so that their outputs can be pulled high. The active-low RESET input pin forces the H-bridge outputs to the low-low state and resets the over-current shutdown latch. The PWDN pin overrides the RESET pin. The ERR0, ERR1, and SHUTDOWN outputs indicate the following conditions in the TAS5110 as shown in the table below. These three outputs are open-drain connections with internal pullup resistors so that wire-ORed connections can be made by the user with other external control devices. The short-circuit protect error condition latches the TAS5110 in this shutdown state and forces the H-bridge outputs to the Hi-Z state until the device is reset by means of the RESET pin. The illegal PWM input state, over-temperature, and low regulator voltage error conditions does not latch the device in the shutdown condition. Instead the H-bridge outputs are forced to the low-low state and the TAS5110 returns to normal operation as soon as the error condition ends. Loss of clocking PWM signal is also considered an illegal PWM input state. 8 SHUTDOWN ERR1 ERR0 OUTPUTA OUTPUTB 0 0 0 Illegal PWM input state FUNCTION Low Low 0 0 1 Short circuit protect (latch) Hi-Z Hi-Z 0 1 0 Over temperature protect Low Low 0 1 1 Low regulator voltage protect Low Low 1 0 0 Reserved — — 1 0 1 Reserved — — 1 1 0 High temperature – warning Normal Normal 1 1 1 Normal operation Normal Normal www.ti.com TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 device operation power sequences system power-up/power-down sequencing The recommended power-up/power-down sequence is shown in Figure 3. For proper operation the RESET signal should be kept low when both DVDD and output power (PVDDA1, PVDDA2, PVDDB1, and PVDDB2) are being applied. The RESET signal should remain low for at least 1 ms after output power is applied. DVDD† PWDN > 1 ms PVDDA2 PVDDB2 > 100 µs PVDDA1 PVDDB1 > 100 µs RESET > 1 ms † For most applications, it is recommended that the PWDN pin be connected directly to the DVDD pin. Figure 3. Power-Up/Power-Down Sequence RESET function The device is put into a reset condition when the (active low) RESET signal is asserted. While in the reset state, the input H-bridge control signals consisting of PWM_AP, PWM_AM, PWM_BP, and PWM_BM are ignored, and the H-bridge MOSFETs are placed in a state where OUTPUTA and OUTPUTB are both low. Asserting the RESET signal low also causes the short circuit protection latch to be reset. The RESET signal is normally connected to the VALID signal from the TAS50xx. reinitialization sequence Proper initial conditions for this device include asserting the RESET signal until the reset operation has completed (1 ms). Additionally, when using this device with the TAS50xx controller, this function can be accomplished by asserting the reset pin on the TAS50xx during the reset sequence (see Figure 3). audio application considerations optimal power transfer for H-bridge The TAS5110 is a power H-bridge that is designed to deliver a maximum of 50 W RMS into a 6-Ω load. In order to achieve 50 W into 6 Ω, the system designer must provide an adequate thermal design. See the Thermal Methodology for the 32-Pin DAD Package 50 W, 6-Ω Test and the Thermal Methodology for the 32-Pin DAP Package 50 W, 6-Ω sections for a discussion of possible thermal solutions. Careful attention must be given to the value of the high-voltage power supply level for a given load resistance. See recommended operating conditions. See the Maximum Available Power at Common Load Impedances for Both DAP and DAD Packages section. www.ti.com 9 TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 audio application considerations (continued) reconstruction output filter An output reconstruction filter is required between the H-bridge outputs and the loudspeaker load. This second order low-pass filter passes the audio information to the loudspeaker, while filtering out the high frequency out-of-band information contained in the H-bridge output PWM pulses. The values of the L and C components selected are dependent on the loudspeaker load impedance. fault indicator usage The TAS5110 is a self-protecting device that provides device fault reporting, including over-temperature protect, under-voltage lockout (low-regulator voltage), and short circuit protection. The short circuit protection protects against short circuits that may occur at the loudspeaker load when configured. The TAS5110 is not recommended for driving loads less than 6 Ω, since the internal current limit protection might be activated. An under-voltage lockout signal occurs when an insufficient voltage level is present on the LDROUTA or LDROUTB pins. During this condition gate drive levels are not sufficient for driving the power MOSFETs. Normal operation is resumed when the minimum proper LDROUTA or LDROUTB level is obtained and the low regulator voltage protect signal is de-asserted. See the control/sense circuitry section for error and warning conditions. A high temperature warning signal is asserted on pin ERR0 when the device temperature exceeds 125°C typical. If the internal device temperature exceeds 150°C typical, the over temperature protect signal is asserted and the TAS5110 is shut down. The device re-enables once the temperature drops to 125°C typical. See the control/sense circuitry section for error and warning conditions. Detection of an illegal PWM input state or the loss of a clocking PWM input signal causes an illegal PWM input state signal to be asserted on the ERR1and ERR0 pins and sets the SHUTDOWN pin to the low state. absolute maximum ratings over operating free-air temperature (unless otherwise noted)† DC supply voltage range: DVDD to DVSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 4.2 V PWM_AP, PWM_AM, PWM_BP, PWM_BM . . . . . . . . . . . . . . . . . –0.3 V to DVDD + 0.3 V RESET, PWDN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to DVDD + 0.3 V PVDDA1 to PVSS, PVDDB1 to PVSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 28 V PVDDA2 to PVSS, PVDDB2 to PVSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 27 V Output DMOS drain-to-source breakdown voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 V Operating junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 150°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 10 www.ti.com TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 recommended operating conditions (maximum output power = 50 W (RMS), TJ = 25°C) thermal data† PARAMETER MIN NOM MAX UNIT Shutdown junction temperature, TJ(SD) 150 °C Warning junction temperature, TJ(W) 125 °C Commercial Operating temperature temperature, TC Industrial 0 25 70 °C –40 25 85 °C Thermal resistance junction-to-case, θjc} 1.6 °C/W 2 oz. oz trace and copper pad without solder } Thermal resistance junction-to-ambient, θja 44.3 °C/W † One of the most influential components on the thermal performance of a package is board design. In order to take full advantage of the heat dissipating abilities of the PowerPAD packages, a board must be used that acts similar to a heat sink and allows for the use of the exposed (and solderable), deep downset pad. See Appendix A of the PowerPAD Thermally Enhanced Package application note, TI literature number SLMA002. ‡ For both DAD and DAP packages. RL = 6 Ω to 8 Ω Digital Supply y voltage g Regulator PARAMETER MIN NOM MAX DVDD to DVSS 3 3.3 3.6 PVDDA2 to PVSS 16.5 22 26.5 PVDDB2 to PVSS 16.5 22 26.5 PVDDA2 to PVSSw 10.5 16.5 PVDDB2 to PVSSw 10.5 16.5 UNIT V V § Connect LDROUTA to PVDDA2 and connect LDROUTB to PVDDB2. Under this condition, the H-bridge forward on-state resistance is increased. This increases internal power dissipation. Maximum output power may need to be reduced to meet thermal conditions. maximum available power at common load impedances for both DAP and DAD packages unclipped (0 dB) level, test conditions described in the Thermal Methodology for the 32-Pin DAD Package 50 W, 6-Ω Test and Thermal Methodology for the 32-Pin DAP Package 50 W, 6-Ω Test sections LOAD IMPEDANCE (Ω) PVDAA1/PVDDB1 (VDC) APPROXIMATE MAX OUTPUT POWER (W) THD+N AT MAX POWER AND 1 kHz INPUT¶ 6 27 50 < 10% 6 27 43 < 0.09% 8 27 34 < 0.09% ¶ Dependent on board design and component selection. static digital specifications RESET, PWDN, PWM_AP, PWM_AM, PWM_BP, PWM_BM, TJ = 25°C, DVDD = 3.3 V PARAMETERS High-level input voltage, VIH MIN MAX 2 Low-level input voltage, VIL Input leakage current –10 UNIT V 0.8 V 10 µA ERR0, ERR1, SHUTDOWN, (open drain with internal pullup resistor) TJ = 25°C, DVDD = 3.3 V) PARAMETERS Internal pullup resistors from SHUTDOWN, ERR0, ERR1 to DVDD Low-level output voltage (IO = 4 mA), VOL MIN MAX 15 kΩ 0.4 www.ti.com UNIT V 11 TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 electrical characteristics supply, TJ = 25°C (Fswitching = 384 kHz, OUTPUTA and OUTPUTB not connected, DVDD = 3.3 V, PVDDA1 = 25 V, PVDDB1 = 25 V, PVDDA2 = 22 V, PVDDB2 = 22 V, 50% input duty cycle) PARAMETER TYP Operating DVDD PVDDA1 PVDDB1 Supply current PVDDA2 PVDDB2 MAX 2 PWDN = 0 Operating† mA 500 6.3 PWDN = 0 6.5 PWDN = 0 µA mA 25 Operating UNIT µA mA 250 µA † 13-kΩ resistor from BIAS_A (pin 11) to DVSS and 13-kΩ resistor from BIAS_B (pin 12) to DVSS. H-Bridge transistors, PVDDA2 = PVDDB2 = 22 V, DVDD = 3.3 V, TJ = 25°C (unless otherwise noted) PARAMETER Drain-to-source breakdown voltage TEST CONDITIONS Forward on-state resistance, low-side drivers OUTPUTA and OUTPUTB to PVSS ID = 1 mA, PWDN = 0, Hi-Z state ISINK = 2.5 A, PWM_AP = PWM_BP = 0, See Notes 1, 2, and 3, PWM_AM = PWM_BM = 1 Forward on-state resistance, high-side drivers PVDDA1 to OUTPUTA, PVDDB1 to OUTPUTB ISOURCE = 2.5 A, See Notes 1, 2, and 4, MIN TYP MAX 28 PWM_AP = PWM_BP = 1, PWM_AM = PWM_BM = 0 UNIT V 0.2 0.24 Ω 0.2 0.24 Ω On-state resistance matching low-side drivers 98% On-state resistance matching high-side drivers 98% NOTES: 1. Test time should be < 1 ms to avoid temperature change. 2. These parameters are measured with voltage-sensing contacts separate from the current-carrying contacts. 3. Connect PVDDA2 and PVDDB2 to a 22-V power supply with respect to PVSS. LDROUTA, LDROUTB, BOOTSTRAPA, and BOOTSTRAPB pins open. 4. Connect PVDDA2 to 22-V power supply with respect to PVSS. LDROUTA, LDROUTB, BOOTSTRAPA, and BOOTSTRAPB capacitors are connected respectively. Clock PWM inputs to allow bootstrap capacitors to charge. 93–99% modulation must be used on PWM_AP, PWM_AM, PWM_BP, and PWM_BM inputs to prevent the activity detector from shutting down the device during this measurement. Note that Fswitching = 384 kHz. electrical characteristics, voltage regulator, TJ = 25°C (unless otherwise noted) PARAMETER Output voltage (LDROUTA, LDROUTB) TEST CONDITIONS IO = 5 mA, See Note 5, PVDDA2 = PVDDB2 = 18 V to 27 V, DVDD = 3.3 V MIN TYP MAX 14.5 15.3 16 UNIT V NOTE 5: These voltage regulators are for internal gate drive circuits only and are not to be used under any circumstances to supply current to external circuity. 12 www.ti.com TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 JUNCTION TEMPERATURE vs ON-STATE RESISTANCE 160 TJ – Junction Temperature – °C 140 120 100 80 60 40 20 0 0.15 0.20 0.25 0.30 0.35 0.40 r(on) – On-State Resistance – Ω Figure 4. Temperature vs On-State Resistance APPLICATION INFORMATION TAS5110 (DAP Package) 1 TAS50xx 2 3 Error Reporting RESET PWM_M_L 4 5 3.3 V 6 PWM_P_L C7 7 8 VALID 9 C2 10 R1 R2 11 12 PWM_AP PVDDA2 PWM_AM LDROUTA ERR1 BOOTSTRAPA ERR0 PVDDA1 SHUTDOWN PVDDA1 DVDD OUTPUTA DVSS OUTPUTA 32 22 V 31 30 C3 29 C4 Snubber Circuit 28 27 L1 26 dc C1 25 DVSS PVSS DVSS PVSS VRFILT OUTPUTB BIAS_A OUTPUTB PVDDB1 BIAS_B 13 PWDN PVDDB1 RESET BOOTSTRAPB 14 15 PWM_BM LDROUTB PWM_BP PVDDB2 16 + _ 24 23 22 L2 21 Snubber Circuit 20 19 C5 C6 18 17 22 V Figure 5. Typical TAS5110 Application (One Channel Shown) www.ti.com 13 TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 THERMAL INFORMATION The thermally enhanced DAP package is based on the 32-pin HTSSOP, but includes a thermal pad (see Figure 6) to provide an effective thermal contact between the IC and the PCB. Traditionally, surface mount and power have been mutually exclusive terms. A variety of scaled-down TO-220 type packages have leads formed as gull wings to make them applicable for surface-mount applications. These packages, however, have two shortcomings: they do not address the low profile requirements (<2 mm) of many of today’s advanced systems, and they do not offer a terminal-count high enough to accommodate increasing integration. On the other hand, traditional low-power surface-mount packages require power-dissipation derating that severely limits the usable range of many high-performance analog circuits. The PowerPAD package (thermally enhanced HTSSOP) combines fine-pitch surface-mount technology with thermal performance comparable to much larger power packages. The PowerPAD package is designed to optimize the heat transfer to the PCB. Because of the very small size and limited mass of a HTSSOP package, thermal enhancement is achieved by improving the thermal conduction paths that remove heat from the component. The thermal pad is formed using a patented lead-frame design and manufacturing technique to provide a direct connection to the heat-generating IC. When this pad is soldered or otherwise thermally coupled to an external heat dissipater, high power dissipation in the ultrathin, fine-pitch, surface-mount package can be reliably achieved. See the dissipation derating table. DAP Package DAD Package Thermal Pad Thermal Pad Bottom View DAP Top View DAD DIE DIE End View DAP End View DAD Figure 6. Views of Thermally Enhanced DAP Package 14 www.ti.com TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 Thermal Methodology for the 32-Pin DAD Package 50 W, 6-Ω Test The thermal test for the DAD part (e.g., thermal pad oriented away from the board) was conducted as shown in Figure 7 and Figure 8. The cooling approach was to attach a heat sink to the thermal pad and conduct the heat to ambient air. Since the approach was to use a chassis below the board, it was inverted and a spacer bar used to connect the pads thermally to the heat sink. The bar was made high enough that the components on the board were clear of the chassis. The pad-to-spacer thermal resistance was about 3.2_C/W with the thermal compound indicated. The chassis provided the only heat sink to air and was chosen as representative of a possible cooling approach. A closed plastic top and insulating front and back panels ensured that only the bottom and sides of the U shaped chassis contributed to cooling. The chassis was spaced 0.25 inch from the table to simulate a normal chassis configuration. The thermal pad does not need to be isolated from ground. (Any heat sink with a thermal resistance to air of 3.9_C/W or lower also works.) In this test, the exposed chassis reached long-term equilibrium temperatures above 50_C, so the approach would have to be modified for touch temperature consideration. The chassis temperature after 10 minutes of 50 W into 6 Ω was below 50_C. The test ran for three hours with 2 x 50 W RMS at 1 kHz into a 6-Ω resistive load at an ambient lab temperature of 23_C. No audio or thermal problems were encountered during that time. Plastic Top Cover 32 DAD Package Insulating Front Panel Stereo Amplifier Board ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÏÏ Wakefield Type 126 Thermal Compound (3.2°C/W) Insulating Back Panel 1.25 in Aluminum Space Bar (1/4 in Thick) (2.44°C/W) Wakefield Type 126 Thermal Compound (0.169°C/W) Aluminum Chassis 7.2 in x 1 in x 0.1 in Thick Sides of U-Shaped Chassis Are 1.25 in High (3.9°C/W) Figure 7. 32-Pin DAD Package Cross-Sectional View (Side) www.ti.com 15 TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 Plastic Top and Insulating Front and Back Panels 32 DAD Packages (1.6°C/W) 4-40 Machine Screws With Star Washers 1 mm ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÏÏ ÏÏ Stereo Amplifier Board Wakefield Type 126 Thermal Compound (3.2°C/W) Aluminum Space Bar (1/4 in Thick) (0.558°C/W) 1.25 in Wakefield Type 126 Thermal Compound (0.169°C/W) 2.33 in Aluminum Chassis 7.2 in x 1 in x 0.1 in Thick Sides of U-Shaped Chassis Are 1.25 in High (3.9°C/W) Figure 8. 32-Pin DAD Package Cross-Sectional View (Front) Thermal Methodology for the 32-Pin DAP Package 50 W, 6-Ω Test The thermal test for the DAP part (e.g., thermal pad soldered to the board) was conducted as shown in Figure 9 and Figure 10. The cooling approach was to conduct the dissipated heat into the via pad on the board, through the vias in the board, and into a heat sink. The lower via pad area, slightly larger than the IC pad itself, was exposed with a window in the solder resist on the bottom surface of the board. It was not coated with solder during the board construction to maintain a flat surface. In production, this could be accomplished with a peelable solder mask. A spacer bar was used to keep the through-hole leads from shorting to the chassis. The thermal compound indicated yielded a pad-to-spacer thermal resistance of about 3.2_C/W. The chassis provided the only heat sink to air and was chosen as representative of a possible cooling approach. A plastic top and insulating front and back panels were used to ensure that only the bottom and sides of the U shaped chassis contributed to cooling. The chassis was spaced 0.25 inch from the table to simulate a normal chassis configuration. (Any heat sink with a thermal resistance to air of 3.9_C/W or lower also works.) In this test, the exposed chassis reached long-term equilibrium temperatures above 50_C, so the approach would have to be modified for touch temperature consideration. The chassis temperature after 10 minutes of 50 W into 6 Ω was below 50_C. The test ran for three hours with 2 x 50 W RMS at 1 kHz into a 6-Ω resistive load at an ambient lab temperature of 23_C. No audio quality or thermal problems were encountered during that time. 16 www.ti.com TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 Insulating Front Panel Insulating Back Panel 1 mm 32 DAP Package ÏÏ ÏÏ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Stereo Amplifier Board Wakefield Type 126 Thermal Compound Wakefield Type 126 Under Via Pads Thermal Compound (4.3°C/W) (0.1°C/W) 1/4 in x 1/4 in x 2.33 in Aluminum Space Bar (0.09°C/W) Aluminum Chassis 7.2 in x 1 in x 0.1 in Thick Sides of U-Shaped Chassis Are 1.25 in High (3.9°C/W) Figure 9. 32-Pin DAP Package Cross-Sectional View (Side) Plastic Top and Insulating Front and Back Panels 32 DAP Packages (1.6°C/W) 4-40 Machine Screws With Star Washers ÏÏ ÌÌ ÌÌ ÏÏ ÌÌ ÌÌ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ Stereo Amplifier Board Wakefield Type 126 Thermal Compound (0.1°C/W) Aluminum Chassis 7.2 in x 1 in x 0.1 in Thick Sides of U-Shaped Chassis Are 1.25 in High (3.9°C/W) 2.33 in Wakefield Type 126 Thermal Compound Under Via Pads (4.3°C/W) Aluminum Space Bar (1/4 in Thick) (0.558°C/W) Figure 10. 32-Pin DAP Package Cross-Sectional View (Front) www.ti.com 17 TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 MECHANICAL DATA DAP (R-PDSO-G**) PowerPAD PLASTIC SMALL-OUTLINE PACKAGE 38 PINS SHOWN 0,30 0,19 0,65 38 0,13 M 20 Thermal Pad (see Note D) 6,20 NOM 8,40 7,80 0,15 NOM Gage Plane 1 19 0,25 A 0°–ā8° 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 28 30 32 38 A MAX 9,80 11,10 11,10 12,60 A MIN 9,60 10,90 10,90 12,40 DIM 4073257/A 07/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion. The package thermal performance may be enhanced by bonding the thermal pad to an external thermal plane. This pad is electrically and thermally connected to the backside of the die and possibly selected leads. Thermal pad size is 3,86 mm X 3,91 mm for the 32-pin TAS5110 device. E. Falls within JEDEC MO-153 PowerPAD is a trademark of Texas Instruments. 18 www.ti.com TAS5110 SLES028A – MAY 2002 – REVISED SEPTEMBER 2002 MECHANICAL DATA DAD (R-PDSO-G**) PowerPAD PLASTIC SMALL-OUTLINE (DIE DOWN) 38 PINS SHOWN 0,30 0,19 0,65 38 0,13 M 20 Thermal Pad (See Note D) 6,20 NOM 8,40 7,80 0,15 NOM Gage Plane 1 19 0,25 A 0°–ā8° 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 30 32 38 A MAX 11,10 11,10 12,60 A MIN 10,90 10,90 12,40 DIM 4073258/A 01/98 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions include mold flash or protrusion. The package thermal performance may be enhanced by attaching an external heatsink to the thermal pad. This pad is electrically and thermally connected to the backside of the die and possibly selected leads. E. Falls within JEDEC MO-153 PowerPAD is a trademark of Texas Instruments Incorporated. www.ti.com 19 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third–party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2002, Texas Instruments Incorporated