PW TPS40090 TPS40091 RHD SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com HIGH-FREQUENCY, MULTIPHASE CONTROLLER Check for Samples: TPS40090, TPS40091 FEATURES 1 DROOP REF COMP 5 6 7 CSCN ILIM 3 4 CS3 CS4 1 11 NC EN/SYNC 24 12 GNDS VIN 23 13 PGOOD BP5 22 14 NC 15 25 SS VOUT NC 17 10 16 26 RT DIFFO NC GND FB 9 19 8 27 18 Internet Servers Network Equipment Telecommunications Equipment DC Power Distributed Systems 28 CS1 PWM3 • • • • CS2 PWM4 APPLICATIONS EN/SYNC VIN BP5 PWM1 PWM2 PWM3 PWM4 GND RT SS PGOOD GNDS RHD PACKAGE (BOTTOM VIEW) 2 • • • • 1% Internal 0.7-V Reference Resistive Divider Set Output Voltage True Remote Sensing Differential Amplifier Resistive or DCR Current Sensing Current Sense Fault Protection Programmable Load Line Compatible with UCC37222 Predictive Gate Drive™ Technology Drivers 24-Pin Space-Saving TSSOP Package 28-Pin QFN Package TPS40090: Binary Outputs TPS40091: 3-State Outputs 24 23 22 21 20 19 18 17 16 15 14 13 21 • • • • • • • Patent pending. 1 2 3 4 5 6 7 8 9 10 11 12 CS1 CS2 CS3 CS4 CSCN ILIM DROOP REF COMP FB DIFFO VOUT 20 (1) PW PACKAGE (TOP VIEW) PWM1 • Two-, Three-, or Four-Phase Operation 5-V to 15-V Operating Range Programmable Switching Frequency Up to 1-MHz/Phase Current Mode Control With Forced Current Sharing(1) PWM2 • • • 2 DESCRIPTION The TPS4009x is a two-, three-, or four-phase programmable synchronous buck controller that is optimized for low-voltage, high-current applications powered by a 5-V to 15-V distributed supply. A multi-phase converter offers several advantages over a single power stage including lower current ripple on the input and output capacitors, faster transient response to load steps, improved power handling capabilities, and higher system efficiency. Each phase can be operated at a switching frequency up to 1-MHz, resulting in an effective ripple frequency of up to 4-MHz at the input and the output in a four-phase application. A two-phase design operates 180 degrees out-of-phase, a three-phase design operates 120 degrees out-of-phase, and a four-phase design operates 90 degrees out-of-phase as shown in Figure 1. The number of phases is programmed by connecting the de-activated phase PWM output to the output of the internal 5-V LDO. In two-phase operation the even phase outputs should be de-activated. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Predictive Gate Drive is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2003–2006, Texas Instruments Incorporated TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. DESCRIPTION CONTINUED The TPS4009x uses fixed frequency, peak current mode control with forced phase current balancing. When compared to voltage mode control, current mode results in a simplified feedback network and reduced input line sensitivity. Phase current is sensed by using either current sense resistors installed in series with output inductors or, for improved efficiency, by using the DCR (direct current resistance) of the filter inductors. The latter method involves generation of a current proportional signal with an R-C circuit (shown in Figure 10). The R-C values are selected by matching the time constants of the R-C circuit and the inductor; R-C = L/DCR. With either current sense method, the current signal is amplified and superimposed on the amplified voltage error signal to provide current mode PWM control. An output voltage droop can be programmed to improve the transient window and reduce size of the output filter. Other features include a single voltage operation, a true differential sense amplifier, a programmable current limit, soft-start and a power good indicator. SIMPLIFIED TWO-PHASE APPLICATION DIAGRAM TPS40090PW CBP5 2 CS2 4 CS4 CS3 RCS3 3 CCS3 14 PGOOD 22 BP5 6 ILIM 17 GND CSCN 5 CCS1 R CS1 CSS 15 CS1 1 VIN 23 VIN (4.5 V to 15 V) CIN SS R ILIM2 L1 RRT 16 RT 7 DROOP 8 REF R DROOP R ILIM1 R FB2 2 21 BP5 CREF R FB3 PWM1 24 EN/SYNC 9 COMP 10 FB CFB1 PWM2 20 PWM4 18 L2 R FB1 PWM3 11 DIFFO 13 GNDS 12 VOUT Submit Documentation Feedback TI Synchronous Buck Driver 19 TI Synchronous Buck Driver VOUT (0.7 V to 3.5 V) COUT Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com ORDERING INFORMATION PACKAGE (1) TA Plastic TSSOP (PW) (2) 40°C to 85°C OUTPUT PART NUMBER Binary TPS40090PW 3-State TPS40091PW TPS40090RHDR QFN (RHD) (3) (1) (2) (3) TPS40091RHDR For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI Web site at www.ti.com. The PWP package is available taped and reeled. Add a R suffix to the device type (i.e., TPS40090PWR). The RHD package is available taped and reeled. Add a R suffix to the device type (i.e., TPS40090RHDR) to order quantities of 3000 parts per reel. Add a T suffix to the device type (i.e., TPS40090RHDT) to order quantities of 250 parts per reel. ABSOLUTE MAXIMUM RATING over operating free-air temperature range unless otherwise noted (1) TPS40090 TPS40091 EN/SYNC, VIN, 16.5 V VIN Input voltage range VOUT Output voltage range TJ Operating junction temperature range -40°C to 125°C Tstg Storage temperature -5°C to 150°C (1) CS1, CS2, CS3, CS4, CSCN, DROOP, FB, GNDS, ILIM, VOUT -0.3 V to 6 V REF, COMP, DIFFO, PGOOD, SS, RT, PWM1, PWM2, PWM3, PWM4, BP5 -0.3 V to 6 V Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS MIN NOM MAX UNIT VIN Input voltage 4.5 15 V TA Operating free-air temperature -40 85 °C Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 Submit Documentation Feedback 3 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com ELECTRICAL CHARACTERISTICS TA = -40°C to 85°C, VIN = 12 V, R(RT) = 64.9 kΩ, TJ = TA (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT INPUT SUPPLY VIN Operating voltage range, VIN 4.5 15 VIN UVLO Rising VIN 4.25 4.45 VIN UVLO (1) Falling VIN 4.1 4.35 IIN Shutdown current, VIN IIN Quiescent current switching Four channels, 400 kHz each, no load V 2 10 μA 4 6 mA OSCILLATOR/SYNCHRONIZATION Phase frequency accuracy Four channels, RRT = 64.9 kΩ 370 Phase frequency set range (1) Four channels 100 415 1200 455 Synchronization frequency range (1) Four channels 800 9600 Synchronization input threshold (1) Four channels VBP5/2 4-phase operation 87.5% 2- and 3-phase operation 83.3% kHz V PWM Maximum duty cycle per channel Minimum duty cycle per channel (1) 0 Minimum controllable on-time (1) 50 100 ns 0.700 0.707 V 25 150 nA ERROR AMPLIFIER Feedback input voltage 0.693 Feedback input bias current VFB = 0.7 V VOH High-level output voltage ICOMP = -1 mA VOL low-level output voltage ICOMP = 1 mA GBW Gain bandwidth (1) 5 MHz AVOL Open loop gain (1) 90 dB 2.5 2.9 0.5 0.8 V SOFT START ISS Soft-start source current 3.5 5 6 μA VSS Soft-start clamp voltage 0.95 1.00 1.05 V Enable threshold voltage 0.8 2 ENABLE Enable voltage capability (1) 2.5 VIN(max) V PWM OUTPUT Ilkg PWM pull-up resistance IOH = 5 mA 27 45 PWM pull-down resistance IOL = 10 mA 27 45 PWM output leakage (1) 3-State (2) 1 Ω μA 5V REGULATOR VOUT Output voltage External ILOAD = 2 mA on BP5 Pass device voltage drop VIN = 4.5 V, No external load on BP5 4.8 Short circuit current (1) (2) 4 10 5 5.2 V 200 mV 30 mA Specified by design. Not production tested. TPS40091 only. Submit Documentation Feedback Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com ELECTRICAL CHARACTERISTICS (continued) TA = -40°C to 85°C, VIN = 12 V, R(RT) = 64.9 kΩ, TJ = TA (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP 4.9 5.4 MAX UNIT CURRENT SENSE AMPLIFIER Gain transfer 100 mV ≤ V(CS) ≤ 100 mV, VCSRTN = 1.5 V Gain variance between phases VCS = 100 mV -4% Input offset variance at zero current VCS = 0 V -3.5 Input common mode (3) 0 0 Bandwidth (3) 5.9 V/V 4% 3.5 4 18 mV V MHz DIFFERENTIAL AMPLIFIER Gain CMRR 1 Gain tolerance VOUT 4 V vs 0.7 V, VGNDS = 0 V Common mode rejection ratio (3) 0.7 V ≤ VOUT ≤ 4 V Bandwidth (3) -0.5% V/V 0.5% 60 dB 5 MHz RAMP Ramp amplitude (3) 0.4 0.5 0.6 V POWER GOOD PGOOD high threshold wrt VREF 10% 14% PGOOD low threshold wrt VREF -14% -10% VOL Low-level output voltage IPGOOD = 4 mA Ilkg PGOOD output leakage VPGOOD = 5 V 0.35 0.60 V 50 80 μA OUTPUT OVERVOLTAGE/UNDERVOLTAGE FAULT VOV Overvoltage threshold voltage VFBK relative to VREF 15% 19% VUV Undervoltage threshold voltage VFBK relative to VREF -18% -14% LOAD LINE PROGRAMMING IDROOP (3) Pull-down current on DROOP 4-phase, VCS = 100 mV 40 μA Specified by design. Not production tested. Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 Submit Documentation Feedback 5 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com Terminal Functions TERMINAL I/O DESCRIPTION 22 O Output of an internal 5V regulator. A 4.7-μF capacitor should be connected from this pin to ground. For 5V applications, this pin should be connected to VDD. 7 9 O Output of the error amplifier. The voltage at this pin determines the duty cycle for the PWM. 27 1 I 28 2 I 1 3 I CS4 2 4 I CSCN 3 5 I Common point of current sense resistors or filter inductors DIFFO 9 11 O Output of the differential amplifier. The voltage at this pin represents the true output voltage without drops that result from high current in the PCB traces DROOP 5 7 I Used to program droop function. A resistor between this pin and the REF pin sets the desired droop value. EN/SYNC 24 24 I A logic high signal on this input enables the controller operation. A pulsing signal to this pin synchronizes the main oscillator to the rising edge of an external clock source. These pulses must be of higher frequency than the free running frequency of the main oscillator set by the resistor from the RT pin. FB 8 10 I Inverting input of the error amplifier. In closed loop operation, the voltage at this pin is the internal reference level of 700 mV. This pin is also used for the PGOOD and OVP comparators. GND 17 17 GNDS 12 13 I Inverting input of the differential amplifier. This pin should be connected to ground at the point of load. ILIM 4 6 I Used to set the cycle-by-cycle current limit threshold. If ILIM threshold is reached, the PWM cycle is terminated and the converter delivers limited current to the output. Under these conditions the undervoltage threshold is reached eventually and the controller enters the hiccup mode. The controller stays in hiccup mode for seven consecutive cycles. At the eighth cycle the controller attempts a full start-up sequence. PGOOD 13 14 O Power good indicator of the output voltage. This open-drain output connects to the supply via an external resistor. PWM1 21 21 O PWM2 20 20 O PWM3 19 19 O PWM4 18 18 O REF 6 8 O Output of an internal 0.7-V reference voltage. RT 16 16 I Connecting a resistor from this pin to ground sets the oscillator frequency. VIN 23 23 I Power input for the chip. De-coupling of this pin is required. VOUT 10 12 I Noninverting input of the differential amplifier. This pin should be connected to VOUT at the point of load. SS 15 15 I Provides user programmable soft-start by means of a capacitor connected to the pin. NC 11, 14, 25, 26 - - No connect pins NAME RHD PW 22 COMP CS1 CS2 CS3 BP5 6 Used to sense the inductor current in the phases. Inductor current can be sensed with an external current sense resistor or by using an external circuit and the inductor's DC resistance. They are also used for overcurrent protection and forced current sharing between the phases. Ground connection to the device. Phase shifted PWM outputs which control the external drivers. The high output signal commands a PWM cycle. The low output signal commands controlled conduction of the synchronous rectifiers. These pins are also used to program various operating modes as follows: for three-phase mode, PWM4 is connected to 5 V; for two-phase mode, PWM2 and PWM4 are connected to 5 V. Submit Documentation Feedback Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com FUNCTIONAL BLOCK DIAGRAM RT 16 TPS40090PW COMP 9 CLOCK FB 10 + 5 mA DROOP 7 REF 8 01 A = -(K +Y) B = +1 A SS 15 + 21 PWM1 IDROOP B 1/N + 700 mV 02 + 20 PWM2 PH2 PH4 A DIFFO 11 GNDS 13 VOUT 12 CSCN 1 CS2 2 CS3 CS4 3 4 + 19 PWM3 A + 04 B 5 CS1 03 B + 18 PWM4 A gM PHDET IPH1 + gM + IPH3 gM + PH2 IPH2 B Σ IPH x K PH2 gM + IPH1 IPH4 IPH2 POWER GOOD IPH3 CURRENT LIMIT 5V REG IPH4 14 16 24 PGOOD ILIM EN/SYNC Product Folder Link(s): TPS40090 TPS40091 23 VIN 22 BP5 17 GND PH4 Copyright © 2003–2006, Texas Instruments Incorporated PH4 Submit Documentation Feedback 18 7 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com APPLICATION INFORMATION FUNCTIONAL DESCRIPTION The TPS4009x is a multiphase, synchronous, peak current mode, buck controller. The controller uses external gate drivers to operate N-channel power MOSFETs. The controller can be configured to operate in a two-, three-, or four-phase power supply. The controller accepts current feedback signals from either current sense resistors placed in series with the filter inductors or current proportional signals derived from the inductors' DCR. Other features include an LDO regulator with UVLO to provide single voltage operation, a differential input amplifier for precise output regulation, user programmable operation frequency for design flexibility, external synchronization capability, programmable pulse-by-pulse overcurrent protection, output overvoltage protection, and output undervoltage shutdown. DIFFERENTIAL AMPLIFIER The unity gain differential amplifier with high bandwidth allows improved regulation at a user-defined point and eases layout constraints. The output voltage is sensed between the VOUT and GNDS pins. The output voltage programming divider is connected to the output of the amplifier (DIFFO). The differential amplifier can be used only for output voltages lower then 3.3 V. If there is no need for a differential amplifier, or if the output voltage required is higher than 3.3-V, the differential amplifier can be disabled by connecting the GNDS pin to the BP5 pin. The voltage programming divider in this case should be connected directly to the output of the converter. CURRENT SENSING AND BALANCING The controller employs a peak current-mode control scheme, which naturally provides a certain degree of current balancing. With current mode, the level of current feedback should comply with certain guidelines depending on duty factor, known as slope compensation to avoid sub-harmonic instability. This requirement can prohibit achieving a higher degree of phase current balance. To avoid the controversy, a separate current loop that forces phase currents to match is added to the proprietary control scheme. This effectively provides high degree of current sharing independently of properties of controller's small signal response. High-bandwidth current amplifiers can accept as an input voltage either voltage drop across dedicated precise current-sense resistors, or inductor's DCR voltage derived by an R-C network, or thermally compensated voltage derived from the inductor's DCR. The wide range of current-sense settings eases the cost and complexity constraints and provides performance superior to those found in controllers using low-side MOSFET current sensing. 8 Submit Documentation Feedback Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com SETTING CONTROLLER CONFIGURATION By default, the controller operates at four-phase configuration. The alternate number of active phases is programmed by connecting unused PWM outputs to BP5. (See Figure 1) For example, for three-phase operation, the unused fourth phase output, PWM4, should be connected to BP5. For two-phase operation, the second, PWM2, and the fourth, PWM4, outputs should be connected to BP5. POWER UP Capacitors connected to the BP5 pin and the soft-start pin set the power-up time. When EN is high, the capacitor connected to the BP5 pin gets charged by the internal LDO as shown in Figure 2. 4.5 C BP5 t BPS + 8 10 *3 (1) EN 1 4-Phase Operation BP5 2 3 SS 4 1.0 0.7 1 3-Phase Operation 2 VOUT 3 4 BP5 PGOOD 1 t - Time 2-Phase Operation 2 BP5 3 4 BP5 Figure 1. Programming Controller Configuration Figure 2. Power-Up Waveforms Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 Submit Documentation Feedback 9 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com When the BP5 pin voltage crosses its lower undervoltage threshold and the power-on reset function is cleared, the calibrated current source starts charging the soft start capacitor. The PGOOD pin is held low during the start up. The rising voltage across the capacitor serves as a reference for the error amplifier assuring start-up in a closed loop manner. When the soft start pin voltage reaches the level of the reference voltage VREF = 0.7 V, the converter's output reaches the regulation point and further rise of the soft start voltage has no effect on the output. 0.7 C SS t SS + 5 10 *6 (2) When the soft-start voltage reaches level of 1 V, the power good (PGOOD) function is cleared and reported on the PGOOD pin. Normally, the PGOOD pin goes high at this moment. The time from when SS begins to rise to when PGOOD is reported is: t PG + 1.43 T SS (3) OUTPUT VOLTAGE PROGRAMMING The converter output voltage is programmed by the R1/R2 divider from the output of the differential amplifier. The center point of the divider is connected to the inverting output of the error amplifier (FB), as shown in Figure 5. V OUT + 0.7 V ǒR1 ) 1Ǔ R2 (4) CURRENT SENSE FAULT PROTECTION Multiphase controllers with forced current sharing are inherently sensitive to failure of a current sense component. In the event of such failure, the whole load current can be steered with catastrophic consequences into a single channel where the fault has happened. The dedicated circuit in the TPS4009x controller prevents it from starting up if any current sense pin is open or shorted to ground. The current-sense fault detection circuit is active only during device initialization, and it does not provide protection should a current-sense failure happen during normal operation. OVERVOLTAGE PROTECTION If the voltage at the FB pin (VFB) exceeds VREF by more than 16%, the TPS4009x enters into an overvoltage state. In this condition, the output signals from the controller to the external drivers is pulled low, causing the drivers to force all of the upper MOSFETs to the OFF position and all the lower MOSFETs to the ON position. As soon as VFB returns to regulation, the normal operating state resumes. 10 Submit Documentation Feedback Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com OVERCURRENT PROTECTION The overcurrent function monitors the voltage level separately on each current sense input and compares it to the voltage on the ILIM pin set by a divider from the controller's reference. In case a threshold of V(ILIM)/2.7 is exceeded the PWM cycle on the associated phase is terminated. The voltage level on the ILIM pin is determined by the following expression: V ILIM + 2.7 I PH(max) R CS (5) I PH(max) + I OUT ) ǒVIN * VOUTǓ 2 L V OUT f SW V IN where: • IPH(max) is a maximum value of the phase current allowed • RCS is a value of the current sense resistor used (6) If the overcurrent condition continues, each phase's PWM cycle is terminated by the overcurrent signals. This puts a converter in a constant current mode with the output current programmed by the ILIM voltage. Eventually, the supply and demand equilibrium on the converter output fails and the output voltage declines. When the undervoltage threshold is reached, the converter enters a hiccup mode. The controller is stopped and the output is not regulated any more, the softstart pin function changes. It now serves as a timing capacitor for a fault control circuit. The soft-start pin is periodically charged and discharged by the fault control circuit. After seven hiccup cycles expire, the controller attempts to restore normal operation. If the overload condition is not cleared, the controller stays in the hiccup mode indefinitely. In such conditions, the average current delivered to the load is roughly 1/8 of the set overcurrent value. UNDERVOLTAGE PROTECTION If the FB pin voltage falls lower than the undervoltage protection threshold (84.5%), the controller enters the hiccup mode as it is described in the Overcurrent Protection section. FAULT-FREE OPERATION If the SS pin voltage is prevented from rising above the 1-V threshold, the controller does not execute nor report most faults and the PGOOD output remains low. Only the overcurrent function and current-sense fault remain active. The overcurrent protection continues to terminate PWM cycle every time when the threshold is exceeded but the hiccup mode is not entered. Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 Submit Documentation Feedback 11 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com SETTING THE SWITCHING FREQUENCY The clock frequency is programmed by the value of the timing resistor connected from the RT pin to ground. R RT + KPH ǒ39.2 10 3 f *1.041 * 7Ǔ PH (7) where: KPH is a coefficient that depends on the number of active phases. For two-phase and three-phase configurations, KPH= 1.333. For four-phase configurations, KPH= 1. fPH is a single phase frequency, kHz. The RT resistor value is returned by the last expression in kΩ. To calculate the output ripple frequency, use the following equation: F RPL + NPH f PH where: • NPH is a number of phases used in the converter. (8) The switching frequency of the controller can be synchronized to an external clock applied to the EN/SYNC pin. The external frequency should be somewhat higher than the free-running clock frequency for synchronization to take place. SWITCHING FREQUENCY vs TIMING RESISTANCE fSW - Switching Frequency - kHz 10000 100 0 50 100 150 200 250 300 RT - Timing Resistance - kΩ Figure 3. 12 Submit Documentation Feedback Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com SETTING THE OUTPUT VOLTAGE DROOP In many applications, the output voltage of the converter is intentionally allowed to droop as load current increases. This approach (sometimes referred to as active load line programming) allows for better use of the regulation window and reduces the amount of the output capacitors required to handle the same load current step. A resistor from the REF pin to the DROOP pin sets the desired value of the output voltage droop. 2500 NPH VDROOP 2500 NPH VDROOP VREF R2 R DROOP + + VOUT I OUT RCS VCS1 ) VCS2 ) VCS3 ) VCS4 R1 ) R2 • • • • • where: VDROOP is the value of droop at maximum load current IOUT NPH is number of phases RCS is the current-sense resistor value 2500 Ω is the inversed value of transconductance from the current sense pins to DROOP VCSx, are the average voltages on the current sense pins OUTPUT VOLTAGE vs OUTPUT CURRENT GNDS (9) Differential Amplifier 13 VOUT + 12 VOUT DIFFO 11 VOUT - Output Voltage - V VDROOP COMP 9 R1 I DROOP C1 Error Amplifier R3 FB 10 + DROOP R2 0 IOUT(max) 7 I DROOP RDROOP REF + IOUT - Output Current - A 8 700 mV Figure 4. Figure 5. Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 Submit Documentation Feedback 13 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com FEEDBACK LOOP COMPENSATION The TPS4009x operates in a peak current mode and the converter exhibits a single pole response with ESR zero for which Type II compensation network is usually adequate, as shown in Figure 7. The following equations show where the load pole and ESR zero calculations are situated. 1 1 f OP + f ESRZ + 2p R OUT C OUT 2p R ESR C OUT (10) To achieve desired bandwidth the error amplifier must compensate for modulator gain loss on the crossover frequency and this is facilitated by placing the zero over the load pole. The ESR zero alters the modulator's -1 slope at higher frequencies. To compensate for that alteration, the pole in-error amplifier transfer function should be added at frequency of the ESR zero as shown in Figure 6. Figure 6. The following equations help in choosing components of the error amplifier compensation network. Fixing the value of the resistor R1 first is recommended as it simplifies further adjustments of the output voltage without altering the compensation network. R2 + R1 10 ǒ *GOMAG 20 Ǔ; C1 + ǒ2p 1 F OP R2Ǔ ; C2 + ǒ2p 1 F ESRZ R2Ǔ where: • GOMAG is the control to output gain at desired system crossover frequency. (11) Introduction of output voltage droop as a measure to reduce amount of filter capacitors changes the transfer function of the modulator as it is shown in the Figure 8. 14 Submit Documentation Feedback Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com GAIN AND PHASE vs FREQUENCY WITH DROOP GAIN AND PHASE vs FREQUENCY WITHOUT DROOP 80 80 Converter Overall EA 60 40 Type II G - Gain - dB G - Gain - dB 40 60 Modulator 20 Droop Zero 20 0 0 Load Pole Load Pole ESR Zero -20 -20 ESR Zero -40 -40 200 200 150 150 Phase 100 Phase - ° Phase - ° 100 50 50 0 0 -50 -50 -100 -100 10 100 1k 10 k f - Frequency - Hz 100 k 1M 10 100 Figure 7. 1k 10 k f - Frequency - Hz 100 k 1M Figure 8. Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 Submit Documentation Feedback 15 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com The droop function, as well as the output capacitor ESR, introduces zero on some frequency left of the crossover point. 1 F + DROOPZ 2p Ǔ ǒ VDROOP I OUT(max) COUT (12) To compensate for this zero, pole on the same frequency should be added to the error amplifier transfer function. With Type II compensation network a new value for the capacitor C2 is required compared to the case without droop. C1 C2 + 2p R2 C1 ǒF DROOPZ * 1Ǔ (13) When attempting to close the feedback loop at frequency that is near the theoretical limit, use the above considerations as a first approximation and perform on bench measurements of closed loop parameters as effects of switching frequency proximity and finite bandwidth of voltage and current amplifiers may substantially alter them as it is shown in Figure 9. GAIN AND PHASE vs FREQUENCY 60 80 Phase 50 60 30 40 20 10 Phase - ° G - Gain - dB 40 20 Gain 0 0 -10 -20 100 VIN = 12 V VOUT = 1.5 V IOUT= 100 A 1k -20 1M 10 k 100 k f - Frequency - Hz Figure 9. 16 Submit Documentation Feedback Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com THERMAL COMPENSATION OF DCR CURRENT SENSING Inductor DCR current sensing is a known lossless technique to retrieve a current proportional signal. Equation 14 and Equation 15 show the calculation used to determine the DCR voltage drop for any given frequency. (See Figure 10) DCR V DCR + ǒVIN * VOUTǓ DCR ) w L (14) 1 V C + ǒVIN * VOUTǓ w C R) 1 w C (15) ǒ Ǔ Voltage across the capacitor is equal to voltage drop across the inductor DCR, VC = VDCR when time constant of the inductor and the time constant of the R-C network are equal: DCR 1 L + R C; t VC + + ; DCRL + t RC DCR ) w L DCR 1 w C R) w C (16) ǒ Ǔ The output signal generated by the network shown in Figure 10 is temperature dependant due to positive thermal coefficient of copper specific resistance as determined using Equation 17. The temperature variation of the inductor coil can exceed 100°C in a practical application leading to approximately 40% variation in the output signal and in turn, respectively move the overcurrent threshold and the load line. K(T) + 1 ) 0.0039 (T * 25) (17) The relatively simple network shown in Figure 11 (made of passive components including one NTC resistor) can provide almost complete compensation for copper thermal variations. L DCR C R R2 R1 RNTC RTHE Figure 10. Figure 11. Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 Submit Documentation Feedback 17 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com The following algorithm and expressions help to determine components of the network. 1. Calculate the equivalent impedance of the network at 25°C that matches the inductor parameters in Equation 18. Use of COG type capacitors for this application is recommended. For example, for L = 0.4 μH, DCR = 1.22 mΩ, C = 10 nF; RE = 33.3 kΩ. It is recommended to keep RE < 50 kΩ as higher values may produce false triggering of the current sense fault protection. L DCR RE + C (18) 2. It is necessary to set the network attenuation value KDIV(25) at 25°C. For example, KDIV(25) = 0.85. The attenuation values KDIV(25) > 0.9 produces higher values for NTC resistors that are harder to get from suppliers. Attenuation values lower 0.7 substantially reduce the network output signal. 3. Based on calculated RE and KDIV(25) values, calculate and pick the closest standard value for the resistor R = RE/KDIV(25). For the given example R = 33 kΩ/ 0.85 = 38.8 kΩ. The closest standard value from 1% line is R = 39.2 kΩ. 4. Pick two temperature values at which curve fitting is made. For example T1 = 50°C and T2 = 90°C. 5. Find the relative values of RTHE required on each of these temperatures. R (T1) R (T2) R THE1 + THE R THE2 + THE R THE(25) R THE(25) (19) RT + K DIV(T) 1 * K DIV(T) R K DIV(25) 1 ) 0.0039 (t * 25) K DIV(T) + (20) For the given example RTHE1= 0.606, RTHE2=0.372. 6. From the NTC resistor datasheet get the relative resistance for resistors with desired curve. For the given example and curve 17 for NTHS NTC resistors from Vishay RNTC1= 0.3507 and RNTC2= 0.08652. 7. Calculate relative values for network resistors including the NTC resistor. R1 R + ǒRNTC1 * RNTC2Ǔ RNTC1 RE1 RE1 R E2 * R NTC1 R E2 ǒ1 * R NTC2Ǔ * RNTC2 ǒ1 * RNTC2Ǔ ) RNTC2 R E1 ǒ1 * RNTC1Ǔ RE2 ǒ1 * R NTC1Ǔ * ǒR NTC1 * R NTC2Ǔ (21) RNTC R + 18 ƫ ƪ R NTC1 1 * 1 * R1R RE1 * R1 R R2 R + ǒ1 * R NTC1Ǔ ƪǒ1 * R1 Ǔ R *1 * ǒR2RǓ Submit Documentation Feedback ƫ *1 *1 (22) *1 (23) Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com For the given example R1R= 0.281, R2R = 2.079, and RNTCR = 1.1. 8. Calculate the absolute value of the NTC resistor as RTHE(25). In given example RNTC = 244.3 kΩ. 9. Find a standard value for the NTC resistor with chosen curve type. In case the close value does not exist in a desired form factor or curve type. Chose a different type of the NTC resistor and repeat steps 6 to 9. In the example, the NTC resistor with the part number NTHS0402N17N2503J with RNTCS(25) = 250 kΩ is close enough to the calculated value. 10. Calculate a scaling factor for the chosen NTC resistor as a ratio between selected and calculated NTC value and. In the example k = 1.023. RNTC S k+ RNTC C (24) 11. Calculate values of the remaining network resistors. R1 C + RTHE(25) ƪǒ(1 * k) ) k R1 RǓƫ (25) For the given example, R1C= 58.7 kΩ and R2C = 472.8 kΩ. Pick the closest available 1% standard values: R1 = 39.2 kΩ, and R2 = 475 kΩ, thus completing the design of the thermally compensated network for the DCR current sensor. Figure 12 illustrates the fit of the designed network to the required function. CURRENT SENSE IMPEDANCE vs AMBIENT TEMPERATURE 40 r Measured RTHE (T5C) - Current Sense Impedance - kΩ Acquired 30 r 20 10 r r 10 20 40 60 80 100 TA - Ambient Temperature - °C 120 Figure 12. Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 Submit Documentation Feedback 19 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 www.ti.com Operation with Output Voltages Higher Than 3.3 V The TPS40090/91 controllers are designed to operate in power supplies with output voltages ranging from 0.7 V to 3.3 V. To support higher output voltages, mainly in 12 V to 5 V power supplies, the BP5 voltage needs to be increased slightly to provide enough headroom to ensure linearity of current sense amplifiers. The simple circuit on Figure 13 shows a configuration that generates a 6-V voltage source to power the controller with increased bias voltage. Both the VIN and BP5 pins should be connected to this voltage source. The differential amplifier normally excessive for higher-output voltages can be disabled by connecting GNDS pin to the BP5 pin. 12 V TPS4009x 1.1 kW EN/SYNC 24 13.7 kW VIN 23 6V BP5 22 4.7 mF TLA431 10 kW Figure 13. Biasing the TPS4009x with a 5-V Power Supply High-Impedance State of TPS40091 Outputs The TPS40091 controller has 3-state enabled outputs to interface various gate drivers and DRMOS devices capable of turning all MOSFETs in the power supply into high-impedance state while remaining active. The common binary output commands the control MOSFET on when the PWM signal is high. Alternatively, the synchronous MOSFET is commanded on when the PWM signal is low. The 3-state output can command both MOSFETs off when the PWM output is in the high-impedance state. This feature simplifies design of power supplies capable of starting into precharged output or allows in VR modules use of gate drivers that do not have the enable input to put VR module off line. Some DRMOS devices like the Philips PIP202 are also compatible with 3-state outputs of the multiphase controller. The TPS40091 outputs have high impedance when the EN pin is high but the soft-start sequence has not been initiated yet. The output impedance is also high when controller is in undervoltage fault condition or disabled. Figure 14 shows a 12-V, 80-A, all-ceramic power supply capable to start into precharged outputs. DESIGN EXAMPLE A design example is available. See the TPS40090EVM−001 user’s guide (SLUU175). 20 Submit Documentation Feedback Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 TPS40090 TPS40091 SLUS578B – OCTOBER 2003 – REVISED MAY 2006 12V + + + + + + 1.2V/100A www.ti.com Figure 14. 12-V, 80-A ASIC All-Ceramic, Power Supply Copyright © 2003–2006, Texas Instruments Incorporated Product Folder Link(s): TPS40090 TPS40091 Submit Documentation Feedback 21 PACKAGE OPTION ADDENDUM www.ti.com 8-Dec-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TPS40090PW ACTIVE TSSOP PW 24 60 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS40090PWG4 ACTIVE TSSOP PW 24 60 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS40090PWR ACTIVE TSSOP PW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS40090PWRG4 ACTIVE TSSOP PW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS40090RHDR ACTIVE VQFN RHD 28 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS40090RHDRG4 ACTIVE VQFN RHD 28 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS40090RHDT ACTIVE VQFN RHD 28 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS40090RHDTG4 ACTIVE VQFN RHD 28 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS40091PW ACTIVE TSSOP PW 24 60 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS40091PWG4 ACTIVE TSSOP PW 24 60 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS40091PWR ACTIVE TSSOP PW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS40091PWRG4 ACTIVE TSSOP PW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS40091RHDR ACTIVE VQFN RHD 28 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS40091RHDRG4 ACTIVE VQFN RHD 28 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS40091RHDT ACTIVE VQFN RHD 28 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS40091RHDTG4 ACTIVE VQFN RHD 28 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 8-Dec-2009 (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TPS40090 : • Automotive: TPS40090-Q1 NOTE: Qualified Version Definitions: • Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPS40090PWR TSSOP PW 24 2000 330.0 16.4 6.95 8.3 1.6 8.0 16.0 Q1 TPS40090RHDR VQFN RHD 28 3000 330.0 12.4 5.3 5.3 1.5 8.0 12.0 Q2 TPS40090RHDT VQFN RHD 28 250 180.0 12.4 5.3 5.3 1.5 8.0 12.0 Q2 TPS40091PWR TSSOP PW 24 2000 330.0 16.4 6.95 8.3 1.6 8.0 16.0 Q1 TPS40091RHDR VQFN RHD 28 3000 330.0 12.4 5.3 5.3 1.5 8.0 12.0 Q2 TPS40091RHDT VQFN RHD 28 250 180.0 12.4 5.3 5.3 1.5 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS40090PWR TPS40090RHDR TSSOP PW 24 2000 367.0 367.0 38.0 VQFN RHD 28 3000 367.0 367.0 35.0 TPS40090RHDT VQFN RHD 28 250 210.0 185.0 35.0 TPS40091PWR TSSOP PW 24 2000 367.0 367.0 38.0 TPS40091RHDR VQFN RHD 28 3000 367.0 367.0 35.0 TPS40091RHDT VQFN RHD 28 250 210.0 185.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated