TI TPA2005D1DGN

TPA2005D1
www.ti.com............................................................................................................................................................... SLOS369F – JULY 2002 – REVISED JULY 2008
1.4-W MONO FILTER-FREE CLASS-D AUDIO POWER AMPLIFIER
FEATURES
1
• 1.4 W Into 8 Ω From a 5 V Supply at
THD = 10% (Typ)
• Maximum Battery Life and Minimum Heat
– Efficiency With an 8-Ω Speaker:
– 84% at 400 mW
– 79% at 100 mW
– 2.8-mA Quiescent Current
– 0.5-µA Shutdown Current
• Capable of Driving an
8-Ω Speaker (2.5 V ≤ VDD ≤ 5.5 V) and a
4-Ω Speaker (2.5 V ≤ VDD ≤ 4.2 V)
• Only Three External Components
– Optimized PWM Output Stage Eliminates
LC Output Filter
– Internally Generated 250-kHz Switching
Frequency Eliminates Capacitor and
Resistor
– Improved PSRR (-71 dB at 217 Hz) and
Wide Supply Voltage (2.5 V to 5.5 V)
Eliminates Need for a Voltage Regulator
– Fully Differential Design Reduces RF
Rectification and Eliminates Bypass
Capacitor
– Improved CMRR Eliminates Two Input
Coupling Capacitors
• Space Saving Package
– 3 mm × 3 mm QFN package (DRB)
– 2,5 mm × 2,5 mm MicroStar Junior™
2
•
BGA Package (ZQY)
– 3 mm x 5 mm MSOP PowerPAD™ Package
(DGN)
– TPA2010D1 Available in 1,45 mm × 1,45 mm
WCSP (YZF)
Use TPA2006D1 for 1.8 V Logic Compatibility
on Shutdown Pin
APPLICATIONS
•
Ideal for Wireless or Cellular Handsets and
PDAs
DESCRIPTION
The TPA2005D1 is a 1.4-W high efficiency filter-free
class-D audio power amplifier in a MicroStar Junior™
BGA, QFN, or MSOP package that requires only
three external components.
Features like 84% efficiency, -71-dB PSRR at 217
Hz, improved RF-rectification immunity, and 15 mm2
total PCB area make the TPA2005D1 ideal for
cellular handsets. A fast start-up time of 9 ms with
minimal pop makes the TPA2005D1 ideal for PDA
applications.
In cellular handsets, the earpiece, speaker phone,
and melody ringer can each be driven by the
TPA2005D1. The device allows independent gain
control by summing the signals from each function
while minimizing noise to only 48 µVRMS.
The TPA2005D1
protection.
has
short-circuit
and
thermal
APPLICATION CIRCUIT
To Battery
Internal
Oscillator
+
RI
Differential
Input
–
RI
CS
IN–
_
PWM
CS
VO+
H–
Bridge
VO–
+
2.5 mm
RI
IN+
GND
SHUTDOWN
Actual Solution Size
(MicroStar Junior BGA)
VDD
Bias
Circuitry
TPA2005D1
RI
6 mm
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
MicroStar Junior, PowerPAD are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2002–2008, Texas Instruments Incorporated
TPA2005D1
SLOS369F – JULY 2002 – REVISED JULY 2008............................................................................................................................................................... www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION
PACKAGE (1)
TA
PART NUMBER
MicroStar Junior™ (GQY)
MicroStar Junior™ (ZQY) (3)
-40°C to 85°C
8-pin QFN (DRB)
8-pin MSOP (DGN)
(1)
(2)
(3)
TPA2005D1GQYR
SYMBOL
(2)
PB051
TPA2005D1ZQYR (2)
TPA2005D1DRBR
AAFI
(2)
BIQ
TPA2005D1DGN(R)
BAL
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
The GQY, ZQY, and DRB packages are only available taped and reeled. An R at the end of the part number indicates the devices are
taped and reeled.
The GQY is the standard MicroStar Junior™ package. The ZQY is lead-free option, and is qualified for 260° lead-free assembly.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted (1)
UNIT
VDD
Supply voltage (2)
VI
Input voltage
In active mode
-0.3 V to 6 V
In SHUTDOWN mode
-0.3 V to 7 V
-0.3 V to VDD + 0.3 V
Continuous total power dissipation
See Dissipation Rating Table
TA
Operating free-air temperature
TJ
Operating junction temperature
-40°C to 85°C
Tstg
Storage temperature
-65°C to 150°C
RL
Load resistance
(1)
(2)
-40°C to 85°C
2.5 ≤ VDD ≤ 4.2 V
3.2 Ω (Minimum)
4.2 < VDD ≤ 6 V
6.4 Ω (Minimum)
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
For the MSOP (DGN) package option, the maximum VDD should be limited to 5 V if short-circuit protection is desired.
RECOMMENDED OPERATING CONDITIONS
MIN
VDD
Supply voltage
VIH
High-level input voltage
VIL
Low-level input voltage
RI
Input resistor
Gain ≤ 20 V/V (26 dB)
VIC
Common mode input voltage range
VDD = 2.5 V, 5.5 V, CMRR ≤ -49 dB
TA
Operating free-air temperature
NOM
MAX
UNIT
2.5
5.5
V
SHUTDOWN
2
VDD
V
SHUTDOWN
0
0.8
15
V
kΩ
0.5
VDD-0.8
V
-40
85
°C
DISSIPATION RATINGS
PACKAGE
2
DERATING
FACTOR
TA ≤ 25°C
POWER RATING
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
GQY, ZQY
16 mW/°C
2W
1.28 W
1.04 W
DRB
21.8 mW/°C
2.7 W
1.7 W
1.4 W
DGN
17.1 mW/°C
2.13 W
1.36 W
1.11 W
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
TPA2005D1
www.ti.com............................................................................................................................................................... SLOS369F – JULY 2002 – REVISED JULY 2008
ELECTRICAL CHARACTERISTICS
TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
|VOS|
Output offset voltage (measured
differentially)
VI = 0 V, AV = 2 V/V, VDD = 2.5 V to 5.5 V
PSRR
Power supply rejection ratio
VDD = 2.5 V to 5.5 V
CMRR
Common mode rejection ratio
VDD = 2.5 V to 5.5 V, VIC= VDD/2 to 0.5 V,
VIC= VDD/2 to VDD- 0.8 V
|IIH|
High-level input current
|IIL|
Low-level input current
I(Q)
Quiescent current
I(SD)
Shutdown current
rDS(on)
f(sw)
Static drain-source on-state
resistance
TYP
MAX
UNIT
25
mV
-75
-55
dB
-68
-49
dB
VDD = 5.5 V, VI = 5.8 V
50
µA
VDD = 5.5 V, VI = 0.3 V
1
µA
VDD = 5.5 V, no load
3.4
VDD = 3.6 V, no load
2.8
VDD = 2.5 V, no load
2.2
3.2
V(SHUTDOWN) = 0.8 V, VDD = 2.5 V to 5.5 V
0.5
2
VDD = 2.5 V
770
VDD = 3.6 V
590
VDD = 5.5 V
500
Output impedance in SHUTDOWN
V(SHUTDOWN) = 0.8 V
Switching frequency
VDD = 2.5 V to 5.5 V
Gain
4.5
mA
mΩ
>1
200
142 kW
RI
2
kΩ
250
2
150 kW
RI
µA
300
158 kW
RI
2
kHz
V
V
OPERATING CHARACTERISTICS
TA = 25°C, Gain = 2 V/V, RL = 8 Ω (unless otherwise noted)
PARAMETER
TEST CONDITIOINS
THD + N= 1%, f = 1 kHz, RL = 8Ω
PO
Output power
THD + N= 10%, f = 1 kHz, RL = 8Ω
THD+N
Total harmonic distortion plus noise
MIN
TYP
VDD = 5 V
1.18
VDD = 3.6 V
0.58
VDD = 2.5 V
0.26
VDD = 5 V
1.45
VDD = 3.6 V
0.75
VDD = 2.5 V
0.35
MAX
UNIT
W
W
PO = 1 W, f = 1 kHz, RL = 8 Ω
VDD = 5 V
0.18%
PO = 0.5 W, f = 1 kHz, RL = 8 Ω
VDD = 3.6 V
0.19%
PO = 200 mW, f = 1 kHz, RL = 8 Ω
VDD = 2.5 V
0.20%
VDD = 3.6 V
-71
dB
dB
kSVR
Supply ripple rejection ratio
f = 217 Hz, V(RIPPLE) = 200 mVpp
Inputs ac-grounded with Ci = 2 µF
SNR
Signal-to-noise ratio
PO= 1 W, RL = 8Ω
VDD = 5 V
97
Vn
Output voltage noise
VDD = 3.6 V, f = 20 Hz to 20 kHz,
Inputs ac-grounded with Ci = 2 µF
No weighting
48
A weighting
36
CMRR
Common mode rejection ratio
VIC = 1 Vpp , f = 217 Hz
VDD = 3.6 V
ZI
Input impedance
-63
142
Start-up time from shutdown
VDD = 3.6 V
µVRMS
150
dB
158
9
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
kΩ
ms
3
TPA2005D1
SLOS369F – JULY 2002 – REVISED JULY 2008............................................................................................................................................................... www.ti.com
PIN ASSIGNMENTS
8-PIN QFN (DRB) PACKAGE
(TOP VIEW)
MicroStar Juniort (GQY) PACKAGE
(TOP VIEW)
SHUTDOWN
NC
IN+
IN−
(A1)
(B1)
(C1)
(D1)
(A4)
(B4)
(C4)
(D4)
(SIDE VIEW)
VO−
SHUTDOWN
VDD
NC
VDD
VO+
IN+
1
3
6 VDD
IN−
4
5 VO+
GND
8-PIN MSOP (DGN) PACKAGE
(TOP VIEW)
8 V
O−
2
SHUTDOWN
1
8
VO−
NC
2
7
GND
IN+
3
6
VDD
IN−
4
5
VO+
7 GND
NC − No internal connection
NOTES A. The shaded terminals are used for electrical and thermal connections to the ground plane. All the shaded terminals need to be electrical
connected to ground. No connect (NC) terminals still need a pad and trace.
B. The thermal pad of the DRB and DGN packages must be electrically and thermally connected to a ground plane.
Terminal Functions
TERMINAL
NAME
I/O
DESCRIPTION
ZQY, GQY
DRB, DGN
IN-
D1
4
I
Negative differential input
IN+
C1
3
I
Positive differential input
VDD
B4, C4
6
I
Power supply
VO+
D4
5
O
Positive BTL output
GND
A2, A3, B3, C2, C3,
D2, D3
7
I
High-current ground
VO-
A4
8
O
Negative BTL output
SHUTDOWN
A1
1
I
Shutdown terminal (active low logic)
NC
B1
2
No internal connection
Thermal Pad
Must be soldered to a grounded pad on the PCB.
FUNCTIONAL BLOCK DIAGRAM
Gain = 2 V/V
VDD
B4, C4
VDD
150 kΩ
IN− D1
_
+
+
_
Deglitch
Logic
Gate
Drive
+
_
Deglitch
Logic
Gate
Drive
A4
VO−
_
+
_
+
+
_
IN+ C1
150 kΩ
SHUTDOWN
†
4
A1
TTL
SD Input
Buffer
Biases
and
References
Ramp
Generator
Startup
& Thermal
Protection
Logic
D4
VO+
Short
Circuit
Detect
†
GND
A2, A3, B3, C2, C3, D2, D3
(terminal labels for MicroStar Junior package)
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
TPA2005D1
www.ti.com............................................................................................................................................................... SLOS369F – JULY 2002 – REVISED JULY 2008
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
Efficiency
vs Output power
Power dissipation
vs Output power
3
Supply current
vs Output power
4, 5
I(Q)
Quiescent current
vs Supply voltage
6
I(SD)
Shutdown current
vs Shutdown voltage
7
PD
PO
Output power
THD+N
Total harmonic distortion plus noise
1, 2
vs Supply voltage
8
vs Load resistance
9, 10
vs Output power
11, 12
vs Frequency
13, 14, 15, 16
vs Common-mode input voltage
kSVR
vs Frequency
Supply voltage rejection ratio
GSM power supply rejection
CMRR
17
Common-mode rejection ratio
18, 19, 20
vs Common-mode input voltage
21
vs Time
22
vs Frequency
23
vs Frequency
24
vs Common-mode input voltage
25
TEST SET-UP FOR GRAPHS
CI
TPA2005D1
RI
+
Measurement
Output
−
IN+
CI
OUT+
Load
RI
IN−
VDD
+
OUT−
30 kHz
Low Pass
Filter
+
Measurement
Input
−
GND
1 µF
VDD
−
Notes:
(1) CI was Shorted for any Common-Mode input voltage measurement
(2) A 33-µH inductor was placed in series with the load resistor to emulate a small speaker for efficiency measurements.
(3) The 30-kHz low-pass filter is required even if the analyzer has a low-pass filter. An RC filter (100 W, 47 nF) is used on
each output for the data sheet graphs.
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
5
TPA2005D1
SLOS369F – JULY 2002 – REVISED JULY 2008............................................................................................................................................................... www.ti.com
EFFICIENCY
vs
OUTPUT POWER
EFFICIENCY
vs
OUTPUT POWER
90
90
RL = 32 W, 33 mH
90
80
80
RL = 8 W, 33 mH
70
Efficiency - %
RL = 16 W, 33 mH
60
50
40
30
Class-AB,
RL = 8 Ω
20
10
70
VDD = 2.5 V,
60
RL = 8W, 33mH
VDD = 5 V,
80
RL = 8W, 33mH
70
Efficiency - %
100
Efficiency - %
EFFICIENCY
vs
OUTPUT POWER
50
40
Class-AB,
VDD = 5 V,
RL = 8 W
30
20
VDD = 3.6
0.1
0.2
0.3
0.4
0.5
0
0.6
0.2
0.4
0.6
0.8
1
0
0
1.2
Figure 3.
POWER DISSIPATION
vs
OUTPUT POWER
SUPPLY CURRENT
vs
OUTPUT POWER
SUPPLY CURRENT
vs
OUTPUT POWER
300
250
VDD = 3.6 V
0.4
RL = 4 W, 33 mH
0.3
VDD = 3.6 V,
RL = 8 W, 33 mH
0.2
RL = 8 Ω, 33 µH
150
100
50
0.1
VDD = 5 V,
RL = 8 W, 33 mH
0
0.2
0.4
0.6
0.8
1
RL = 32 Ω, 33 µH
0
0
1.2
200
150
VDD = 5 V,
RL = 8 Ω, 33 µH
100
VDD = 3.6 V,
RL = 8 Ω, 33 µH
50
0.1
PO - Output Power - W
0.2
0.3
0.4
PO - Output Power - W
VDD = 2.5 V,
RL = 8 Ω, 33 µH
0
0.5
0
0.6
0.2
0.4
0.6
0.8
1
Figure 5.
Figure 6.
QUIESCENT CURRENT
vs
SUPPLY VOLTAGE
SHUTDOWN CURRENT
vs
SHUTDOWN VOLTAGE
OUTPUT POWER
vs
SUPPLY VOLTAGE
3.8
1
1.6
3.6
0.9
1.4
3.2
3
2.8
No Load
2.6
2.4
2.2
0.8
PO - Output Power - W
RL = 8 Ω, 33 µH
0.7
0.6
VDD = 2.5 V
0.5
0.4
VDD = 3.6 V
0.3
VDD = 5 V
3.5
4
4.5
5
5.5
VDD − Supply Voltage − V
Figure 7.
1.2
1
THD+N = 10%
0.8
0.6
THD+N = 1%
0.4
0.2
0
0
3
RL = 8 Ω
f = 1 kHz
Gain = 2 V/V
0.2
0.1
2
1.2
PO - Output Power - W
Figure 4.
I (SD) - Shutdown Current - µ A
I (Q) − Quiescent Current − mA
Supply Current - mA
Class-AB,
VDD = 3.6 V,
RL = 8 W
0.5
250
200
VDD = 4.2 V,
Supply Current - mA
PD - Power Dissipation - W
0.6
2.5
1.5
Figure 2.
Class-AB, V DD = 5 V, RL = 8 W
3.4
0.5
1
PO - Output Power - W
Figure 1.
0.7
6
30
PO - Output Power - W
PO - Output Power - W
0
40
10
0
0
50
20
10
0
VDD = 4.2 V,
RL = 4 W, 33 mH
60
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
Shutdown Voltage - V
Figure 8.
Submit Documentation Feedback
0.8
2.5
3
3.5
4
4.5
5
VDD - Supply Voltage - V
Figure 9.
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
TPA2005D1
www.ti.com............................................................................................................................................................... SLOS369F – JULY 2002 – REVISED JULY 2008
OUTPUT POWER
vs
SUPPLY VOLTAGE
OUTPUT POWER
vs
LOAD RESISTANCE
1.4
R L = 4 W,
f = 1kHz,
Gain = 2 V/V
1.2
PO - Output Power - W
THD+N = 10%
1
0.8
THD+N = 1%
0.6
0.4
VDD = 3.6 V
VDD = 4.2 V
0.8
VDD = 5 V
0.6
0.4
VDD = 5 V
1.2
VDD = 4.2 V
1
VDD = 3.6 V
0.8
0.6
0.4
0.2
VDD = 2.5 V
0
0
2.5
3
3.5
4
VDD - Supply Voltage - V
4
4.5
8
12
16
20
24
RL - Load Resistance - W
28
VDD = 2.5 V
0
4
32
8
12
16
20
24
RL - Load Resistance - W
28
32
Figure 11.
Figure 12.
TOTAL HARMONIC DISTORTION +
NOISE
vs
OUTPUT POWER
TOTAL HARMONIC DISTORTION +
NOISE
vs OUTPUT POWER
TOTAL HARMONIC DISTORTION +
NOISE
vs
OUTPUT POWER
30
20
10
R L = 4 W,
f = 1 kHz,
Gain = 2 V/V
VDD = 2.5 V
5
VDD = 3.6 V
2
VDD = 4.2 V
1
0.5
0.2
0.1
0.01
0.1
1
2
30
20
10
RL = 8 Ω,
f = 1 kHz,
Gain = 2 V/V
5
2.5 V
2
3.6 V
1
5V
0.5
0.2
0.1
0.01
0.1
1
2
THD+N − Total Harmonic Distortion + Noise − %
Figure 10.
THD+N − Total Harmonic Distortion + Noise − %
THD+N - Total Harmonic Distortion + Noise - %
1.4
1
0.2
0.2
30
20
RL = 16 Ω,
f = 1 kHz,
Gain = 2 V/V
10
5
2.5 V
2
3.6 V
1
5V
0.5
0.2
0.1
0.01
0.1
1
2
PO − Output Power − W
PO − Output Power − W
Figure 13.
Figure 14.
Figure 15.
TOTAL HARMONIC DISTORTION +
NOISE
vs
FREQUENCY
TOTAL HARMONIC DISTORTION +
NOISE
vs
FREQUENCY
TOTAL HARMONIC DISTORTION +
NOISE
vs
FREQUENCY
10
VDD = 5 V
CI = 2 µF
RL = 8 Ω
Gain = 2 V/V
5
2
1
0.5
0.2
50 mW
0.1
1W
0.05
0.02
250 mW
20
100
1k
f − Frequency − Hz
20 k
THD+N − Total Harmonic Distortion + Noise − %
PO - Output Power - W
THD+N − Total Harmonic Distortion + Noise − %
f = 1 kHz,
THD+N = 10%,
Gain = 2 V/V
1.6
Figure 16.
10
5
2
VDD = 3.6 V
CI = 2 µF
RL = 8 Ω
Gain = 2 V/V
1
0.5
0.2
500 mW
25 mW
0.1
0.05
125 mW
0.02
0.01
20
100
1k
f − Frequency − Hz
Figure 17.
20 k
THD+N − Total Harmonic Distortion + Noise − %
PO - Output Power - W
1.4
1.8
f = 1 kHz,
THD+N = 1%,
Gain = 2 V/V
1.2
PO - Output Power - W
1.6
0.008
OUTPUT POWER
vs
LOAD RESISTANCE
10
VDD = 2.5 V
CI = 2 µF
RL = 8 Ω
Gain = 2 V/V
5
2
1
15 mW
75 mW
0.5
0.2
0.1
200 mW
0.05
0.02
0.01
20
100
1k
Figure 18.
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
20 k
f − Frequency − Hz
7
TPA2005D1
SLOS369F – JULY 2002 – REVISED JULY 2008............................................................................................................................................................... www.ti.com
VDD = 3.6 V
CI = 2 µF
RL = 16 Ω
Gain = 2 V/V
5
2
1
0.5
0.2
15 mW
0.1
75 mW
0.05
0.02
0.01
200 mW
20
100
1k
20 k
10
VDD = 4.2 V,
R L = 4 W,
Gain = 2 V/V
5
2
500 mW
1
0.5
250 mW
1W
0.2
0.1
0.05
0.02
0.01
20
100
VDD = 3.6 V,
R L = 4 W,
Gain = 2V/V
5
2
1
250 mW
0.5
775 mW
500 mW
0.2
0.1
0.05
0.02
0.01
20
100
1k
f-Frequency-Hz
20k
Figure 21.
TOTAL HARMONIC DISTORTION +
NOISE
vs
FREQUENCY
TOTAL HARMONIC DISTORTION +
NOISE
vs
COMMON MODE INPUT VOLTAGE
SUPPLY VOLTAGE REJECTION
RATIO
vs
FREQUENCY
75 mW
2
15 mW
1
0.5
200 mW
0.2
0.1
0.05
0.02
0.01
20
100
1k
f - Frequency - Hz
20k
10
− Supply Voltage Rejection Ratio − dB
SVR
VDD = 2.5 V,
R L = 4 W,
Gain = 2V/V
5
f = 1 kHz
PO = 200 mW
1
VDD = 2.5 V
VDD = 3.6 V
0.1
k
10
THD+N - Total Harmonic Distortion + Noise - %
Figure 20.
0
0
CI = 2 µF
RL = 8 Ω
Vp-p = 200 mV
Inputs ac-Grounded
Gain = 2 V/V
−10
−20
−30
−40
VDD = 3.6 V
−50
VDD =2. 5 V
−60
−70
VDD = 5 V
−80
20
0.5
1
1.5
2
2.5
3
3.5
VIC - Common Mode Input Voltage - V
100
1k
f − Frequency − Hz
20 k
Figure 22.
Figure 23.
Figure 24.
SUPPLY VOLTAGE REJECTION
RATIO
vs
FREQUENCY
SUPPLY VOLTAGE REJECTIO RATIO
vs
FREQUENCY
SUPPLY VOLTAGE REJECTION
RATIO
vs
COMMON-MODE INPUT VOLTAGE
−20
−30
VDD = 2. 5 V
−40
−50
VDD = 5 V
−60
−70
VDD = 3.6 V
−80
100
1k
f − Frequency − Hz
20 k
Figure 25.
−20
−30
- Supply Voltage Rejection Ratio - dB
−10
0
0
−10
CI = 2 µF
RL = 8 Ω
Inputs Floating
Gain = 2 V/V
−40
−50
−60
VDD = 3.6 V
−70
−80
SVR
Gain = 5 V/V
CI = 2 µF
RL = 8 Ω
Vp-p = 200 mV
Inputs ac-Grounded
−90
−100
20
k
− Supply Voltage Rejection Ratio − dB
SVR
0
20
8
20k
10
Figure 19.
k
k
− Supply Voltage Rejection Ratio − dB
SVR
THD+N - Total Harmonic Distortion + Noise - %
f − Frequency − Hz
1k
f - Frequency - Hz
TOTAL HARMONIC DISTORTION +
NOISE
vs
FREQUENCY
THD+N - Total Harmonic Distortion + Noise - %
10
TOTAL HARMONIC DISTORTION +
NOISE
vs
FREQUENCY
THD+N - Total Harmonic Distortion + Noise - %
THD+N − Total Harmonic Distortion + Noise − %
TOTAL HARMONIC DISTORTION +
NOISE
vs
FREQUENCY
100
1k
f − Frequency − Hz
Figure 26.
Submit Documentation Feedback
20 k
f = 217 Hz
RL = 8 Ω
Gain = 2 V/V
-10
-20
-30
-40
VDD = 2.5 V
-50
VDD = 3.6 V
-60
-70
-80
VDD = 5 V
-90
0
0.5 1 1.5 2 2.5 3 3.5 4 4.5 5
VIC - Common Mode Input Voltage - V
Figure 27.
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
TPA2005D1
www.ti.com............................................................................................................................................................... SLOS369F – JULY 2002 – REVISED JULY 2008
GSM POWER SUPPLY REJECTION
vs
FREQUENCY
0
C1 - Duty
12.6%
-50
C1 Frequency
216.7448 Hz
-100
C1 - Amplitude
512 mV
C1 - High
3.544 V
VOUT
VO - Output Voltage - dBV
Voltage - V
VDD
0
VDD Shown in Figure 22
CI = 2 µF,
Inputs ac-grounded
Gain = 2V/V
-50
-100
-150
0
400
t - Time - ms
800
1200
1600
2000
f - Frequency - Hz
Figure 28.
Figure 29.
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
COMMON-MODE REJECTION RATIO
vs
COMMON-MODE INPUT VOLTAGE
0
−10
−20
CMRR - Common Mode Rejection Ratio - dB
CMRR − Common Mode Rejection Ratio − dB
-150
V DD - Supply Voltage - dBV
GSM POWER SUPPLY REJECTION
vs
TIME
VDD = 2.5 V to 5 V
VIC = 1 Vp−p
RL = 8 Ω
Gain = 2 V/V
−30
−40
−50
−60
−70
20
100
1k
f − Frequency − Hz
0
RL = 8 Ω
Gain = 2 V/V
-10
-20
-30
-40
VDD = 2.5 V
VDD = 3.6 V
-50
-60
-70
-80
VDD = 5 V
-90
-100
20 k
Figure 30.
0
0.5 1 1.5 2 2.5 3 3.5 4 4.5
VIC - Common Mode Input Voltage - V
5
Figure 31.
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
9
TPA2005D1
SLOS369F – JULY 2002 – REVISED JULY 2008............................................................................................................................................................... www.ti.com
APPLICATION INFORMATION
FULLY DIFFERENTIAL AMPLIFIER
The TPA2005D1 is a fully differential amplifier with differential inputs and outputs. The fully differential amplifier
consists of a differential amplifier and a common-mode amplifier. The differential amplifier ensures that the
amplifier outputs a differential voltage on the output that is equal to the differential input times the gain. The
common-mode feedback ensures that the common-mode voltage at the output is biased around VDD/2 regardless
of the common-mode voltage at the input. The fully differential TPA2005D1 can still be used with a single-ended
input; however, the TPA2005D1 should be used with differential inputs when in a noisy environment, like a
wireless handset, to ensure maximum noise rejection.
Advantages of Fully Differential Amplifiers
• Input-coupling capacitors not required:
– The fully differential amplifier allows the inputs to be biased at voltage other than mid-supply. For example,
if a codec has a midsupply lower than the midsupply of the TPA2005D1, the common-mode feedback
circuit will adjust, and the TPA2005D1 outputs will still be biased at midsupply of the TPA2005D1. The
inputs of the TPA2005D1 can be biased from 0.5 V to VDD - 0.8 V. If the inputs are biased outside of that
range, input-coupling capacitors are required.
• Midsupply bypass capacitor, C(BYPASS), not required:
– The fully differential amplifier does not require a bypass capacitor. This is because any shift in the
midsupply affects both positive and negative channels equally and cancels at the differential output.
• Better RF-immunity:
– GSM handsets save power by turning on and shutting off the RF transmitter at a rate of 217 Hz. The
transmitted signal is picked-up on input and output traces. The fully differential amplifier cancels the signal
much better than the typical audio amplifier.
COMPONENT SELECTION
Figure 32 shows the TPA2005D1 typical schematic with differential inputs and Figure 33 shows the TPA2005D1
with differential inputs and input capacitors, and Figure 34 shows the TPA2005D1 with single-ended inputs.
Differential inputs should be used whenever possible because the single-ended inputs are much more
susceptible to noise.
Table 1. Typical Component Values
(1)
REF DES
VALUE
EIA SIZE
MANUFACTURER
RI
150 kΩ (0.5%)
0402
Panasonic
PART NUMBER
ERJ2RHD154V
CS
1 µF (+22%, -80%)
0402
Murata
GRP155F50J105Z
CI (1)
3.3 nF (10%)
0201
Murata
GRP033B10J332K
CI is only needed for single-ended input or if VICM is not between 0.5 V and VDD - 0.8 V. CI = 3.3 nF (with RI = 150 kΩ) gives a
high-pass corner frequency of 321 Hz.
To Battery
Internal
Oscillator
+
RI
–
RI
CS
IN–
_
Differential
Input
VDD
PWM
H–
Bridge
VO+
VO–
+
IN+
GND
SHUTDOWN
Bias
Circuitry
TPA2005D1
Filter-Free Class D
Figure 32. Typical TPA2005D1 Application Schematic With Differential Input for a Wireless Phone
10
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
TPA2005D1
www.ti.com............................................................................................................................................................... SLOS369F – JULY 2002 – REVISED JULY 2008
To Battery
CI
Internal
Oscillator
RI
CI
RI
CS
IN–
PWM
_
Differential
Input
VDD
H–
Bridge
VO+
VO–
+
IN+
GND
Bias
Circuitry
SHUTDOWN
TPA2005D1
Filter-Free Class D
Figure 33. TPA2005D1 Application Schematic With Differential Input and Input Capacitors
To Battery
CI
Single-ended
Input
Internal
Oscillator
RI
CS
IN–
_
RI
VDD
PWM
H–
Bridge
VO–
+
IN+
CI
SHUTDOWN
VO+
GND
Bias
Circuitry
TPA2005D1
Filter-Free Class D
Figure 34. TPA2005D1 Application Schematic With Single-Ended Input
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
11
TPA2005D1
SLOS369F – JULY 2002 – REVISED JULY 2008............................................................................................................................................................... www.ti.com
Input Resistors (RI)
The input resistors (RI) set the gain of the amplifier according to equation Equation 1.
Gain + 2 150 kW
R
I
(1)
Resistor matching is important in fully differential amplifiers. The balance of the output on the reference
voltage depends on matched ratios of the resistors. CMRR, PSRR, and cancellation of the second harmonic
distortion diminish if resistor mismatch occurs. Therefore, it is recommended to use 1% tolerance resistors or
better to keep the performance optimized. Matching is more important than overall tolerance. Resistor arrays with
1% matching can be used with a tolerance greater than 1%.
Place the input resistors close to the TPA2005D1 to limit noise injection on the high-impedance nodes.
For optimal performance the gain should be set to 2 V/V or lower. Lower gain allows the TPA2005D1 to operate
at its best, and keeps a high voltage at the input making the inputs less susceptible to noise.
Decoupling Capacitor (CS)
The TPA2005D1 is a high-performance class-D audio amplifier that requires adequate power supply decoupling
to ensure the efficiency is high and total harmonic distortion (THD) is low. For higher frequency transients,
spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor, typically 1
µF, placed as close as possible to the device VDD lead works best. Placing this decoupling capacitor close to the
TPA2005D1 is important for the efficiency of the class-D amplifier, because any resistance or inductance in the
trace between the device and the capacitor can cause a loss in efficiency. For filtering lower-frequency noise
signals, a 10 µF or greater capacitor placed near the audio power amplifier would also help, but it is not required
in most applications because of the high PSRR of this device.
Input Capacitors (CI)
The TPA2005D1 does not require input coupling capacitors if the design uses a differential source that is biased
from 0.5 V to VDD - 0.8 V (shown in Figure 32). If the input signal is not biased within the recommended
common-mode input range, if needing to use the input as a high pass filter (shown in Figure 33), or if using a
single-ended source (shown in Figure 34), input coupling capacitors are required.
The input capacitors and input resistors form a high-pass filter with the corner frequency, fc, determined in
equation Equation 2.
1
fc +
2p R C
I I
(2)
ǒ
Ǔ
The value of the input capacitor is important to consider as it directly affects the bass (low frequency)
performance of the circuit. Speakers in wireless phones cannot usually respond well to low frequencies, so the
corner frequency can be set to block low frequencies in this application.
Equation Equation 3 is reconfigured to solve for the input coupling capacitance.
1
C +
I
2p R f c
I
ǒ
Ǔ
(3)
If the corner frequency is within the audio band, the capacitors should have a tolerance of 10% or better,
because any mismatch in capacitance causes an impedance mismatch at the corner frequency and below, and
causes pop. Any capacitor in the audio path should have a rating of X7R or better.
For a flat low-frequency response, use large input coupling capacitors (1 µF). However, in a GSM phone the
ground signal is fluctuating at 217 Hz, but the signal from the codec does not have the same 217 Hz fluctuation.
The difference between the two signals is amplified, sent to the speaker, and heard as a 217 Hz hum.
12
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
TPA2005D1
www.ti.com............................................................................................................................................................... SLOS369F – JULY 2002 – REVISED JULY 2008
SUMMING INPUT SIGNALS WITH THE TPA2005D1
Most wireless phones or PDAs need to sum signals at the audio power amplifier or just have two signal sources
that need separate gain. The TPA2005D1 makes it easy to sum signals or use separate signal sources with
different gains. Many phones now use the same speaker for the earpiece and ringer, where the wireless phone
would require a much lower gain for the phone earpiece than for the ringer. PDAs and phones that have stereo
headphones require summing of the right and left channels to output the stereo signal to the mono speaker.
Summing Two Differential Input Signals
Two extra resistors are needed for summing differential signals (a total of 5 components). The gain for each input
source can be set independently (see equations Equation 4 and Equation 5, and Figure 35).
V
V
Gain 1 + O + 2 150 kW
V
R
V
I1
I1
(4)
V
V
Gain 2 + O + 2 150 kW
V
R
V
I2
I2
(5)
ǒǓ
ǒǓ
If summing left and right inputs with a gain of 1 V/V, use RI1= RI2= 300 kΩ.
If summing a ring tone and a phone signal, set the ring-tone gain to Gain 2 = 2 V/V, and the phone gain to gain
1 = 0.1 V/V. The resistor values would be. . .
• RI1 = 3 MΩ, and = RI2 = 150 kΩ.
Differential
Input 1
+
RI1
–
RI1
+
RI2
To Battery
Internal
Oscillator
Differential
Input 2
RI2
CS
IN–
_
–
VDD
PWM
H–
Bridge
VO+
VO–
+
IN+
GND
Bias
Circuitry
SHUTDOWN
Filter-Free Class D
Figure 35. Application Schematic With TPA2005D1 Summing Two Differential Inputs
Summing a Differential Input Signal and a Single-Ended Input Signal
Figure 36 shows how to sum a differential input signal and a single-ended input signal. Ground noise can couple
in through IN+ with this method. It is better to use differential inputs. The corner frequency of the single-ended
input is set by CI2, shown in equation Equation 8. To assure that each input is balanced, the single-ended input
must be driven by a low-impedance source even if the input is not in use.
V
V
Gain 1 + O + 2 150 kW
V
R
V
I1
I1
(6)
V
V
Gain 2 + O + 2 150 kW
V
R
V
I2
I2
(7)
1
C +
I2
ǒ2p RI2 f c2Ǔ
(8)
ǒǓ
ǒǓ
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
13
TPA2005D1
SLOS369F – JULY 2002 – REVISED JULY 2008............................................................................................................................................................... www.ti.com
If summing a ring tone and a phone signal, the phone signal should use a differential input signal while the ring
tone might be limited to a single-ended signal. Phone gain is set at gain 1 = 0.1 V/V, and the ring-tone gain is set
to gain 2 = 2 V/V, the resistor values would be…
• RI1 = 3 MΩ, and = RI2 = 150 kΩ.
The high pass corner frequency of the single-ended input is set by CI2. If the desired corner frequency is less
than 20 Hz.
1
C u
I2
ǒ2p 150kW 20HzǓ
(9)
C
I2
u 53pF
(10)
RI1
Differential
Input 1
RI1
CI2 R
I2
Single-Ended
To Battery
Internal
Oscillator
CS
IN–
Input 2
_
RI2
VDD
PWM
H–
Bridge
VO+
VO–
+
IN+
CI2
GND
Bias
Circuitry
SHUTDOWN
Filter-Free Class D
Figure 36. Application Schematic With TPA2005D1 Summing Differential Input and
Single-Ended Input Signals
Summing Two Single-Ended Input Signals
Four resistors and three capacitors are needed for summing single-ended input signals. The gain and corner
frequencies (fc1 and fc2) for each input source can be set independently (see equations Equation 11 through
Equation 14, and Figure 37). Resistor, RP, and capacitor, CP, are needed on the IN+ terminal to match the
impedance on the IN- terminal. The single-ended inputs must be driven by low impedance sources even if one of
the inputs is not outputting an ac signal.
14
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
TPA2005D1
www.ti.com............................................................................................................................................................... SLOS369F – JULY 2002 – REVISED JULY 2008
V
Gain 1 +
V
V
Gain 2 +
C
C
I1
I2
+
+
V
O+2
I1
150 kW
R
I1
ǒVVǓ
O+2
I2
1
150 kW
R
I2
ǒVVǓ
(11)
(12)
ǒ2p RI1 f c1Ǔ
(13)
1
ǒ2p RI2 f c2Ǔ
(14)
C +C ) C
P
I1
I2
R
R
I2
R + I1
P
R ) R
I1
I2
ǒ
(15)
Ǔ
(16)
Single-Ended
Input 1
Single-Ended
Input 2
CI1 R
I1
To Battery
CI2 R
I2
Internal
Oscillator
CS
IN–
_
RP
VDD
PWM
H–
Bridge
VO+
VO–
+
IN+
CP
GND
SHUTDOWN
Bias
Circuitry
Filter-Free Class D
Figure 37. Application Schematic With TPA2005D1 Summing Two Single-Ended Inputs
EFFICIENCY AND THERMAL INFORMATION
The maximum ambient temperature depends on the heat-sinking ability of the PCB system. The derating factor
for the 2,5-mm x 2,5-mm MicroStar Junior package is shown in the dissipation rating table. Converting this to θJA:
1
q
+
+ 1 + 62.5°CńW
JA
0.016
Derating Factor
(17)
Given θJA of 62.5°C/W, the maximum allowable junction temperature of 150°C, and the maximum internal
dissipation of 0.2 W (worst case 5-V supply), the maximum ambient temperature can be calculated with equation
Equation 18.
T Max + T Max * q P
+ 150 * 62.5 (0.2) + 137.5°C
A
J
JA Dmax
(18)
Equation Equation 18 shows that the calculated maximum ambient temperature is 137.5°C at maximum power
dissipation with a 5-V supply; however, the maximum ambient temperature of the package is limited to 85°C.
Because of the efficiency of the TPA2005D1, it can be operated under all conditions to an ambient temperature
of 85°C. The TPA2005D1 is designed with thermal protection that turns the device off when the junction
temperature surpasses 150°C to prevent damage to the IC. Also, using speakers more resistive than 8-Ω
dramatically increases the thermal performance by reducing the output current and increasing the efficiency of
the amplifier.
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
15
TPA2005D1
SLOS369F – JULY 2002 – REVISED JULY 2008............................................................................................................................................................... www.ti.com
BOARD LAYOUT
Component Location
Place all the external components close to the TPA2005D1. The input resistors need to be close to the
TPA2005D1 input pins so noise does not couple on the high impedance nodes between the input resistors and
the input amplifier of the TPA2005D1. Placing the decoupling capacitor, CS, close to the TPA2005D1 is important
for the efficiency of the class-D amplifier. Any resistance or inductance in the trace between the device and the
capacitor can cause a loss in efficiency.
Trace Width
Make the high current traces going to pins VDD, GND, VO+ and VO- of the TPA2005D1 have a minimum width of
0,7 mm. If these traces are too thin, the TPA2005D1's performance and output power will decrease. The input
traces do not need to be wide, but do need to run side-by-side to enable common-mode noise cancellation.
MicroStar Junior™ BGA Layout
Use the following MicroStar Junior BGA ball diameters:
• 0,25 mm diameter solder mask
• 0,28 mm diameter solder paste mask/stencil
• 0,38 mm diameter copper trace
Figure 38 shows how to lay out a board for the TPA2005D1 MicroStar Junior BGA.
0,28
mm
SD
0,38
mm
NC
0,25
mm
GND
GND
Vo−
GND
VDD
IN+
GND
GND
VDD
IN−
GND
GND
Vo+
Solder Mask
Paste Mask
Copper Trace
Figure 38. TPA2005D1 MicroStar Junior BGA Board Layout (Top View)
16
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
TPA2005D1
www.ti.com............................................................................................................................................................... SLOS369F – JULY 2002 – REVISED JULY 2008
ELIMINATING THE OUTPUT FILTER WITH THE TPA2005D1
This section focuses on why the user can eliminate the output filter with the TPA2005D1.
Effect on Audio
The class-D amplifier outputs a pulse-width modulated (PWM) square wave, which is the sum of the switching
waveform and the amplified input audio signal. The human ear acts as a band-pass filter such that only the
frequencies between approximately 20 Hz and 20 kHz are passed. The switching frequency components are
much greater than 20 kHz, so the only signal heard is the amplified input audio signal.
Traditional Class-D Modulation Scheme
The traditional class-D modulation scheme, which is used in the TPA005Dxx family, has a differential output
where each output is 180 degrees out of phase and changes from ground to the supply voltage, VDD. Therefore,
the differential pre-filtered output varies between positive and negative VDD, where filtered 50% duty cycle yields
0 volts across the load. The traditional class-D modulation scheme with voltage and current waveforms is shown
in Figure 39. Note that even at an average of 0 volts across the load (50% duty cycle), the current to the load is
high causing a high loss and thus causing a high supply current.
OUT+
OUT–
+5 V
Differential Voltage
Across Load
0V
–5 V
Current
Figure 39. Traditional Class-D Modulation Scheme's Output Voltage and Current Waveforms Into an
Inductive Load With no Input
TPA2005D1 Modulation Scheme
The TPA2005D1 uses a modulation scheme that still has each output switching from 0 to the supply voltage.
However, OUT+ and OUT- are now in phase with each other with no input. The duty cycle of OUT+ is greater
than 50% and OUT- is less than 50% for positive voltages. The duty cycle of OUT+ is less than 50% and OUT- is
greater than 50% for negative voltages. The voltage across the load sits at 0 volts throughout most of the
switching period greatly reducing the switching current, which reduces any I2R losses in the load.
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
17
TPA2005D1
SLOS369F – JULY 2002 – REVISED JULY 2008............................................................................................................................................................... www.ti.com
OUT+
OUT–
Differential
Voltage
Across
Load
Output = 0 V
+5 V
0V
–5 V
Current
OUT+
OUT–
Differential
Voltage
Output > 0 V
+5 V
0V
Across
Load
–5 V
Current
Figure 40. The TPA2005D1 Output Voltage and Current Waveforms Into an Inductive Load
Efficiency: Why You Must Use a Filter With the Traditional Class-D Modulation Scheme
The main reason that the traditional class-D amplifier needs an output filter is that the switching waveform results
in maximum current flow. This causes more loss in the load, which causes lower efficiency. The ripple current is
large for the traditional modulation scheme because the ripple current is proportional to voltage multiplied by the
time at that voltage. The differential voltage swing is 2 × VDD and the time at each voltage is half the period for
the traditional modulation scheme. An ideal LC filter is needed to store the ripple current from each half cycle for
the next half cycle, while any resistance causes power dissipation. The speaker is both resistive and reactive,
whereas an LC filter is almost purely reactive.
The TPA2005D1 modulation scheme has little loss in the load without a filter because the pulses are short and
the change in voltage is VDD instead of 2 × VDD. As the output power increases, the pulses widen making the
ripple current larger. Ripple current could be filtered with an LC filter for increased efficiency, but for most
applications the filter is not needed.
An LC filter with a cutoff frequency less than the class-D switching frequency allows the switching current to flow
through the filter instead of the load. The filter has less resistance than the speaker that results in less power
dissipated, which increases efficiency.
Effects of Applying a Square Wave Into a Speaker
If the amplitude of a square wave is high enough and the frequency of the square wave is within the bandwidth
of the speaker, a square wave could cause the voice coil to jump out of the air gap and/or scar the voice coil. A
250-kHz switching frequency, however, is not significant because the speaker cone movement is proportional to
1/f2 for frequencies beyond the audio band. Therefore, the amount of cone movement at the switching frequency
is small. However, damage could occur to the speaker if the voice coil is not designed to handle the additional
power. To size the speaker for added power, the ripple current dissipated in the load needs to be calculated by
subtracting the theoretical supplied power, PSUP THEORETICAL, from the actual supply power, PSUP, at maximum
output power, POUT. The switching power dissipated in the speaker is the inverse of the measured efficiency,η
MEASURED, minus the theoretical efficiency,η THEORETICAL.
18
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
TPA2005D1
www.ti.com............................................................................................................................................................... SLOS369F – JULY 2002 – REVISED JULY 2008
P
–P
(at max output power)
SUP SUP THEORETICAL
P
P
P
+ SUP – SUP THEORETICAL (at max output power)
SPKR
P
P
OUT
OUT
P
SPKR
SPKR
+P
+P
ǒ
(19)
(20)
Ǔ
1
1
*
(at max output power)
OUT h MEASURED h THEORETICAL
(21)
R
hTHEORETICAL +
R
L
(at max output power)
) 2r
L
DS(on)
(22)
The maximum efficiency of the TPA2005D1 with a 3.6 V supply and an 8-Ω load is 86% from equation
Equation 22. Using equation Equation 21 with the efficiency at maximum power (84%), we see that there is an
additional 17 mW dissipated in the speaker. The added power dissipated in the speaker is not an issue as long
as it is taken into account when choosing the speaker.
When to Use an Output Filter
Design the TPA2005D1 without an output filter if the traces from amplifier to speaker are short. The TPA2005D1
passed FCC and CE radiated emissions with no shielding with speaker trace wires 100 mm long or less.
Wireless handsets and PDAs are great applications for class-D without a filter.
A ferrite bead filter can often be used if the design is failing radiated emissions without an LC filter, and the
frequency sensitive circuit is greater than 1 MHz. This is good for circuits that just have to pass FCC and CE
because FCC and CE only test radiated emissions greater than 30 MHz. If choosing a ferrite bead, choose one
with high impedance at high frequencies, but low impedance at low frequencies.
Use an LC output filter if there are low frequency (< 1 MHz) EMI sensitive circuits and/or there are long leads
from amplifier to speaker.
Figure 41 and Figure 42 show typical ferrite bead and LC output filters.
Ferrite
Chip Bead
OUTP
1 nF
Ferrite
Chip Bead
OUTN
1 nF
Figure 41. Typical Ferrite Chip Bead Filter (Chip bead example: NEC/Tokin: N2012ZPS121)
33 µH
OUTP
1 µF
33 µH
OUTN
1 µF
Figure 42. Typical LC Output Filter, Cutoff Frequency of 27 kHz
Submit Documentation Feedback
Copyright © 2002–2008, Texas Instruments Incorporated
Product Folder Link(s): TPA2005D1
19
PACKAGE OPTION ADDENDUM
www.ti.com
24-Jan-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package Qty
Drawing
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
TPA2005D1DGN
ACTIVE
MSOPPowerPAD
DGN
8
80
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
BAL
TPA2005D1DGNG4
ACTIVE
MSOPPowerPAD
DGN
8
80
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
BAL
TPA2005D1DGNR
ACTIVE
MSOPPowerPAD
DGN
8
2500
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
BAL
TPA2005D1DGNRG4
ACTIVE
MSOPPowerPAD
DGN
8
2500
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
BAL
TPA2005D1DRBR
ACTIVE
SON
DRB
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BIQ
TPA2005D1DRBRG4
ACTIVE
SON
DRB
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
BIQ
TPA2005D1GQYR
ACTIVE
BGA
MICROSTAR
JUNIOR
GQY
15
2500
TBD
SNPB
Level-2-235C-1 YEAR
-40 to 85
PB051
TPA2005D1ZQYR
ACTIVE
BGA
MICROSTAR
JUNIOR
ZQY
15
2500
Green (RoHS
& no Sb/Br)
SNAGCU
Level-2-260C-1 YEAR
-40 to 85
AAFI
TPA2005D1ZQYRG1
ACTIVE
BGA
MICROSTAR
JUNIOR
ZQY
15
2500
Green (RoHS
& no Sb/Br)
SNAGCU
Level-2-260C-1 YEAR
-40 to 85
AAFI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
24-Jan-2013
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Only one of markings shown within the brackets will appear on the physical device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPA2005D1 :
• Automotive: TPA2005D1-Q1
NOTE: Qualified Version Definitions:
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TPA2005D1DGNR
MSOPPower
PAD
DGN
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
TPA2005D1DRBR
SON
DRB
8
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPA2005D1DRBR
SON
DRB
8
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
ZQY
15
2500
330.0
8.4
2.8
2.8
1.25
4.0
8.0
Q1
TPA2005D1ZQYR
BGA MI
CROSTA
R JUNI
OR
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPA2005D1DGNR
MSOP-PowerPAD
DGN
8
2500
364.0
364.0
27.0
TPA2005D1DRBR
SON
DRB
8
3000
367.0
367.0
35.0
TPA2005D1DRBR
SON
DRB
8
3000
367.0
367.0
35.0
TPA2005D1ZQYR
BGA MICROSTAR
JUNIOR
ZQY
15
2500
338.1
338.1
20.6
Pack Materials-Page 2
MECHANICAL DATA
MPBG168B – SEPTEMBER 2000 – REVISED FEBRUARY 2002
GQY (S-PBGA-N15)
PLASTIC BALL GRID ARRAY
1,50 TYP
2,60
SQ
2,40
0,50
0,25
D
0,50
C
1,50 TYP
B
0,25
A
1
A1 Corner
2
3
4
Bottom View
0,77
0,71
1,00 MAX
Seating Plane
0,35
0,25
0,05 M
0,25
0,15
0,08
4201436/D 01/02
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
MicroStar Junior configuration
Falls within JEDEC MO-225
MicroStar Junior is a trademark of Texas Instruments.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated