TI TPA2033D1

TPA2032D1
TPA2033D1
TPA2034D1
www.ti.com
SLOS476 – JUNE 2006
2.75-W FIXED GAIN MONO FILTER-FREE CLASS-D AUDIO POWER AMPLIFIER
• Wafer Chip Scale Packaging (WCSP)
– NanoFree™ Lead-Free (Pb-Free: YZF)
FEATURES
•
•
•
•
•
Maximize Battery Life and Minimize Heat
– 0.5-µA Shutdown Current
– 3.0-mA Quiescent Current
– High Efficiency Class-D
• 88% at 400mW at 8Ω
• 80% at 100mW at 8Ω
Three Fixed Gain Versions
– TPA2032D1 has a gain of 2 V/V (6dB)
– TPA2033D1 has a gain of 3 V/V (9.5dB)
– TPA2034D1 has a gain of 4 V/V (12dB)
Only One External Component Required
– Internal Matched Input Gain and Feedback
Resistors for Excellent PSRR and CMRR
– Optimized PWM Output Stage Eliminates
LC Output Filter
– PSRR (–75 dB) and Wide Supply Voltage
(2.5 V to 5.5 V) Eliminates Need for a
Dedicated Voltage Regulator
– Fully Differential Design Reduces RF
Rectification and Eliminates Bypass
Capacitor
– CMRR (–69 dB)Eliminates Two Input
Coupling Capacitors
Thermal and Short-Circuit Protection
Pinout Very Similar to TPA2010D1
APPLICATIONS
•
Ideal for Wireless Handsets, PDAs, and other
mobile devices
DESCRIPTION
The TPA2032D1 (2V/V gain), TPA2033D1 (3V/V
gain), and TPA2034D1 (4V/V gain) are 2.75-W high
efficiency filter-free class-D audio power amplifiers,
each in an approximately 1.5-mm × 1.5-mm wafer
chip scale package (WCSP) that requires only one
external component. The pinout is the same as the
TPA2010D1 except that the external gain setting
input resistors required by the TPA2010D1 are
integrated into the fixed gain TPA203xD1 family.
Features like –75dB PSRR and improved
RF-rectification immunity with a very small PCB
footprint (WCSP amplifier plus single decoupling
cap) make the TPA203xD1 family ideal for wireless
handsets. A fast start-up time of 3.2 ms with minimal
pop makes the TPA203xD1 family ideal for PDA
applications.
In wireless handsets, the earpiece, speaker phone,
and melody ringer can each be driven by a
TPA203xD1. The TPA203xD1 family has a low
27-µV noise floor, A-weighted.
APPLICATION CIRCUIT
VDD
IN−
_
Differential
Input
PWM
203xD1
CS
~ 2,5 mm
VO−
H−
Bridge
9-BALL WAFER CHIP SCALE, YZF PACKAGE,
(TOP VIEW OF PCB)
VO+
+
IN+
GND
SHUTDOWN
~1,7 mm
TPA
To Battery
Internal
Oscillator
0402
CS
Bias
Circuitry
TPA2032D1
1,4 mm
1,55 mm
IN+
GND
A1
A2
VDD
PV DD
B1
B2
VO−
A3
PGND
B3
IN− SHUTDWN VO+
C1
C2
C3
1,4 mm
1,55 mm
Note: Pin A1 is marked with a “0” .
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
NanoFree is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006, Texas Instruments Incorporated
TPA2032D1
TPA2033D1
TPA2034D1
www.ti.com
SLOS476 – JUNE 2006
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION
TA
PACKAGE
–40°C to 85°C
Wafer chip scale packaging – Lead free (YZF)
TPA2032D1YZF
(1)
BPX
–40°C to 85°C
Wafer chip scale packaging – Lead free (YZF)
TPA2033D1YZF
(1)
BPY
TPA2034D1YZF
(1)
BPZ
–40°C to 85°C
(1)
PART NUMBER
Wafer chip scale packaging – Lead free (YZF)
SYMBOL
The YZF package is only available taped and reeled. To order add the suffix R to the end of the part number for a reel of 3000, or add
the suffix T to the end of the part number for a reel of 250 (e.g. TPA2032D1YZFR).
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted (1)
TPA2032D1, TPA2033D1,
TPA2034D1
VDD
Supply voltage
VI
Input voltage
In active mode
–0.3 V to 6 V
In SHUTDOWN mode
–0.3 V to 7 V
–0.3 V to VDD + 0.3 V
Continuous total power dissipation
See Dissipation Rating Table
TA
Operating free-air temperature
–40°C to 85°C
TJ
Operating junction temperature
–40°C to 125°C
Tstg
Storage temperature
ESD
(1)
–65°C to 150°C
Electro-Static Discharge Tolerance - Human Body Model (HBM) for all
pins (2)
2KV
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The output pins Vo– and Vo+ are tolerant to 1.5KV HBM ESD
(2)
RECOMMENDED OPERATING CONDITIONS
MIN
VDD
Supply voltage
2.5
VIH
High-level input voltage
SHUTDOWN
VIL
Low-level input voltage
SHUTDOWN
VIC
TA
NOM
MAX
UNIT
5.5
V
1.3
VDD
V
0
0.35
V
Common mode input voltage range VDD = 2.5 V, 5.5 V
0.5
VDD–0.8
V
Operating free-air temperature
–40
85
°C
PACKAGE DISSIPATION RATINGS
(1)
(2)
2
PACKAGE
DERATING FACTOR
(1 / θJA)
TA ≤ 25°C
POWER RATING
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
YZF
4.8 mW/°C (1)
480 mW
264 mW
192 mW
YZF
7.5 mW/°C (2)
750 mW
412 mW
300 mW
Derating factor measured with JEDEC Low-K board; 1S0P - One signal layer and zero plane layers.
Derating factor measured with JEDEC High K board; 1S2P - One signal layer and two plane layers.
Please see JEDEC Standard 51-3 for Low-K board, JEDEC Standard 51-7 for High-K board, and JEDEC Standard 51-12 for using
package thermal information.
Please see JEDEC document page for downloadable copies: http://www.jedec.org/download/default.cfm.
Submit Documentation Feedback
TPA2032D1
TPA2033D1
TPA2034D1
www.ti.com
SLOS476 – JUNE 2006
ELECTRICAL CHARACTERISTICS
TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
|VOS|
Output offset voltage
(measured differentially)
Inputs AC grounded, VDD = 2.5 V to 5.5 V
PSRR
Power supply rejection ratio
VDD = 2.5 V to 5.5 V
MIN
TYP MAX
TPA2032D1
5
25
TPA2033D1
5
25
TPA2034D1
CMRR
Common mode rejection ratio
VIC = 0.5 V to (VDD –0.8 V)
|IIH|
High-level input current
VDD = 5.5 V, VI = 5.8 V
|IIL|
Low-level input current
VDD = 5.5 V, VI = –0.3 V
5
25
–75
-61
VDD = 2.5 V
–69
-52
VDD = 3.6 V
– 69
-52
VDD = 5.5 V
–69
-52
VDD = 5.5 V, no load
I(Q)
I(SD)
rDS(on)
f(sw)
Quiescent current
Shutdown current
Static drain-source on-state
resistance
RPD
5
µA
3
3.7
V(SHUTDOWN)= 0.35 V, VDD = 2.5 V to 5.5 V
0.5
0.8
VDD = 2.5 V
550
VDD = 3.6 V
420
VDD = 5.0 V
350
VDD = 2.5 V to 5.5 V
mA
VDD = 2.5 V to 5.5 V
300
kΩ
400
TPA2032D1
5.5
6
6.5
TPA2033D1
9.0
9.5
10.0
TPA2034D1
11.5
12
12.5
Resistance of internal pulldown
resistor from shutdown pin to
GND
µA
mΩ
2
240
dB
5.7
2.2
Switching frequency
dB
µA
VDD = 2.5 V, no load
V(SHUTDOWN) <= 0.35 V
mV
50
VDD = 3.6 V, no load
Output impedance in
SHUTDOWN
Gain
4
UNIT
300
kHz
dB
kΩ
OPERATING CHARACTERISTICS
TA = 25°C, RL = 8 Ω (unless otherwise noted)
PARAMETER
TEST CONDITIONS
RL = 4 Ω, THD + N = 10%, f = 1 kHz
RL = 4 Ω, THD + N = 1%, f = 1 kHz
PO
Output power
RL = 8 Ω, THD + N = 10%, f = 1 kHz
RL = 8 Ω, THD + N = 1%, f = 1 kHz
Total harmonic distortion plus
noise
TYP MAX
2.75
VDD = 3.6 V
1.35
VDD = 2.5 V
0.59
VDD = 5 V
2.25
VDD = 3.6 V
1.12
VDD = 2.5 V
0.48
VDD = 5 V
1.68
VDD = 3.6 V
0.85
VDD = 2.5 V
0.38
VDD = 5 V
1.37
VDD = 3.6 V
0.68
VDD = 2.5 V
THD+
N
MIN
VDD = 5 V
0.18%
VDD = 3.6 V, PO = 0.5 W, RL = 8 Ω, f = 1 kHz
0.11%
VDD = 2.5 V, PO = 200 mW, RL = 8 Ω, f = 1 kHz
0.10%
f = 217 Hz,
V(RIPPLE) = 200 mVpp
kSVR
Supply ripple rejection ratio
SNR
Signal-to-noise ratio
VDD = 5 V, PO = 1 W, RL = 8 Ω, A weighted noise
Submit Documentation Feedback
W
W
W
W
0.31
VDD = 5 V, PO = 1 W, RL = 8 Ω, f = 1 kHz
VDD = 3.6 V, Inputs AC grounded
with CI = 1 µF
UNIT
–73
dB
100
dB
3
TPA2032D1
TPA2033D1
TPA2034D1
www.ti.com
SLOS476 – JUNE 2006
OPERATING CHARACTERISTICS (continued)
TA = 25°C, RL = 8 Ω (unless otherwise noted)
PARAMETER
Vn
TEST CONDITIONS
VDD = 3.6 V, f = 20 Hz to 20 kHz,
Inputs AC grounded with Ci = 1 µF
Output voltage noise
CMRR Common mode rejection ratio
RI
Input impedance
Start-up time from shutdown
MIN
TYP MAX
No weighting
35
A weighting
27
VDD = 3.6 V, VIC = 1.0 Vpp , VCm = 1.8
f = 217 Hz
V
–69
AV = 2 V/V
30.2
AV = 3 V/V
22.8
AV = 4 V/V
18.5
VDD = 3.6 V
3.2
UNIT
µVRMS
dB
kΩ
ms
Terminal Functions
TERMINAL
NAME
YZF
IN–
C1
IN+
VO-
I/O
DESCRIPTION
I
Negative differential audio input
A1
I
Positive differential audio input
A3
O
Negative BTL audio output
VO+
C3
O
Positive BTL audio output
GND
A2
I
Analog ground terminal. Must be connected to same potential as PGND using a direct connection
to a single point ground.
PGND
B3
VDD
B1
I
PVDD
B2
I
High-current Power supply terminal. Must be connected to same power supply as VDD using a
direct connection. Voltage must be within values listed in Recommended Operating Conditions
table.
SHUTDOWN
C2
I
Shutdown terminal. When terminal is low the device is put into Shutdown mode.
High-current Analog ground terminal. Must be connected to same potential as GND using a direct
connection to a single point ground.
Power supply terminal. Must be connected to same power supply as PVDD using a direct
connection. Voltage must be within values listed in Recommended Operating Conditions table.
FUNCTIONAL BLOCK DIAGRAM
Input
Buffer
SC
300 KΩ
4
Submit Documentation Feedback
TPA2032D1
TPA2033D1
TPA2034D1
www.ti.com
SLOS476 – JUNE 2006
TYPICAL CHARACTERISTICS
TABLE OF GRAPHS
FIGURE
Efficiency
vs Output power
1, 2
Power dissipation
vs Output power
3, 4
Supply current
vs Output power
5, 6
IDD
Supply current
vs Supply voltage
7
I(SD)
Shutdown current
vs Shutdown voltage
PD
PO
Output power
8
vs Load resistance
9, 10
vs Supply voltage
11
vs Output power
12, 13
THD+N Total harmonic distortion plus noise vs Frequency
14, 15, 16, 17
vs Common-mode input voltage
KSVR
Supply voltage rejection ratio
Supply voltage rejection ratio
CMRR
19, 20, 21, 22, 23, 24, 25,
26, 27
vs Frequency
GSM power supply rejection
KSVR
18
vs Time
28
vs Frequency
29
vs Common-mode input voltage
Common-mode rejection ratio
30, 31, 32
vs Frequency
33
vs Common-mode input voltage
34
TEST SET-UP FOR GRAPHS
CI
TPA2032D1
+
Measurement
Output
IN+
OUT+
Load
CI
IN −
−
OUT −
+
Measurement
Input
−
GND
V DD
+
30 kHz
Low Pass
Filter
1mF
V DD
−
(1)
CI was shorted for any common-mode input voltage measurement. All other measurements were taken with a 1-µF
CI (unless otherwise noted).
(2)
A 33-µH inductor was placed in series with the load resistor to emulate a small speaker for efficiency measurements.
(3)
The 30-kHz low-pass filter is required, even if the analyzer has an internal low-pass filter. An RC low-pass filter
(100Ω, 47-nF) is used on each output for the data sheet graphs.
Submit Documentation Feedback
5
TPA2032D1
TPA2033D1
TPA2034D1
www.ti.com
SLOS476 – JUNE 2006
EFFICIENCY
vs
OUTPUT POWER
VDD = 2.5 V
90
80
Efficiency - %
1.4
80
1.2
Class AB 4 W
VDD = 5 V
VDD = 3.6 V
50
Class AB
40
VDD = 3.6 V
60
VDD = 2.5 V
50
40
Class AB
30
30
20
RL = 8 W, 33 μH
0
0.2
0.4
0.6
0.8
1
PO - Output Power - W
1.2
1.4
0.4
VDD = 5 V, RL = 8 W
0.5
1
1.5
2
PO - Output Power - W
0
2.5
0.5
1
1.5
2
2.5
Figure 3.
POWER DISSIPATION
vs
OUTPUT POWER
SUPPLY CURRENT
vs
OUTPUT POWER
SUPPLY CURRENT
vs
OUTPUT POWER
650
360
RL = 4 W, 33 μH
600
0.6
IDD - Supply Current - mA
VDD = 3.6 V, RL = 4 W
Class AB, 8 W
0.3
0.2
500
450
400
VDD = 5 V
350
300
250
VDD = 3.6 V
200
150
0
0.2
0.4 0.6 0.8
1
1.2
PO - Output Power - W
1.4
0
1.6
VDD = 3.6 V
240
VDD = 5 V
200
160
120
VDD = 2.5 V
40
50
VDD = 3.6 V, RL = 8 W
280
80
VDD = 2.5 V
100
0.1
RL = 8 W, 33 μH
320
550
0.5
3
PO - Output Power - W
Figure 2.
Class AB, 4 W
0
VDD = 5 V, RL = 4 W
0.6
Figure 1.
0.7
0.4
Class AB 8 W
0.8
0
0
0
0
1
0.2
RL = 4 W, 33 μH
10
10
IDD - Supply Current - mA
Efficiency - %
60
20
PD - Power Dissipation - W
90
70
VDD = 5 V
70
POWER DISSIPATION
vs
OUTPUT POWER
PD - Power Dissipation - W
100
EFFICIENCY
vs
OUTPUT POWER
0
0
0.5
1
1.5
2
2.5
PO - Output Power - W
3
0
0.5
0.25
1
0.75
1.5
1.25
1.75
PO - Output Power - W
Figure 4.
Figure 5.
Figure 6.
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
SHUTDOWN CURRENT
vs
SHUTDOWN VOLTAGE
OUTPUT POWER
vs
LOAD RESISTANCE
3.6
RL = 8 W
3.2
IDD - Supply Current - mA
IDD - Supply Current - mA
3.4
3.2
3
2.8
RL = 8 W, 33 mH
2.6
No Load
2.4
2.2
2
2.5
3
2.8
VDD = 5 V
2.4
2
1.6
VDD = 3.6 V
1.2
0.8
VDD = 2.5 V
3
4.5
3.5
4
5
VDD - Supply Voltage - V
5.5
0
0
0.1
0.2 0.3 0.4 0.5 0.6
Shutdown Voltage - V
2.5
VDD = 5 V, 10%
2
VDD = 3.6 V, 10%
1.5
VDD = 2.5 V, 10%
1
0.5
0.4
Figure 7.
6
3.5
RL = No Load
PO - Output Power - W
3.6
0.7
Figure 8.
Submit Documentation Feedback
0.8
0
4
9
14
19
24
RL - Load Resistance - W
Figure 9.
29
TPA2032D1
TPA2033D1
TPA2034D1
www.ti.com
SLOS476 – JUNE 2006
3
2.5
4 W THD+N = 10%
2.5
PO - Output Power - W
VDD = 5 V, 1%
1.5
VDD = 3.6 V, 1%
1
VDD = 2.5 V, 1%
4 W THD+N = 1%
2
8 W THD+N = 10%
1.5
1
0.5
0.5
0
0
4
9
14
19
24
8 W THD+N = 1%
2.5
29
3
3.5
4
4.5
VDD - Supply Voltage - V
5
20
RL = 4 W
10
VDD = 2.5 V
VDD = 3 V
VDD = 3.6 V
1
VDD = 5 V
0.1
0.05
10m
100m
1
PO - Output Power - W
3
Figure 11.
Figure 12.
TOTAL HARMONIC DISTORTION +
NOISE
vs
OUTPUT POWER
TOTAL HARMONIC DISTORTION +
NOISE
vs
FREQUENCY
TOTAL HARMONIC DISTORTION +
NOISE
vs
FREQUENCY
20
10
RL = 8 W
VDD = 2.5 V
VDD = 3 V
VDD = 3.6 V
1
VDD = 5 V
0.1
0.05
10m
100m
PO - Output Power - W
1
2
THD+N - Total Harmonic Distortion + Noise - %
Figure 10.
1
RL = 8 W
VDD = 5 V
PO = 50 mW
0.1
PO = 250 mW
PO = 1 W
0.01
20
100
1k
f - Frequency - Hz
10k 20k
1
RL = 8 W
VDD = 3.6 V
PO = 25 mW
PO = 125 mW
0.1
PO = 500 mW
0.01
20
100
1k
f - Frequency - Hz
10k 20k
Figure 13.
Figure 14.
Figure 15.
TOTAL HARMONIC DISTORTION +
NOISE
vs
FREQUENCY
TOTAL HARMONIC DISTORTION +
NOISE
vs
FREQUENCY
TOTAL HARMONIC DISTORTION +
NOISE
vs
COMMON MODE INPUT VOLTAGE
1
RL = 8 W
VDD = 2.5 V
PO = 15 mW
0.1
PO = 75 mW
PO = 200 mW
0.01
0.005
20
100
1k
f - Frequency - Hz
Figure 16.
10k 20k
THD+N - Total Harmonic Distortion + Noise - %
THD+N - Total Harmonic Distortion + Noise - %
RL - Load Resistance - W
THD+N - Total Harmonic Distortion + Noise - %
PO - Output Power - W
2
THD+N - Total Harmonic Distortion + Noise - %
TOTAL HARMONIC DISTORTION +
NOISE
vs
OUTPUT POWER
OUTPUT POWER
vs
SUPPLY VOLTAGE
THD+N - Total Harmonic Distortion + Noise - %
OUTPUT POWER
vs
LOAD RESISTANCE
1
RL = 4 W
VDD = 5 V
VDD = 4 V
VDD = 3 V
0.1
VDD = 2.5 V
VDD = 3.6 V
0.01
20
100
1k
f - Frequency - Hz
10k 20k
Figure 17.
Submit Documentation Feedback
Figure 18.
7
TPA2032D1
TPA2033D1
TPA2034D1
www.ti.com
SLOS476 – JUNE 2006
SUPPLY RIPPLE REJECTION RATIO
vs
FREQUENCY - TPA2033D1
R L = 8 W,
-50
-60
Gain = 2 V/V
VDD = 2.5 V
-70
-80
-90
-100
10
VDD = 3.6 V
VDD = 5 V
100
1k
f - Frequency - Hz
10 k
Gain = 3 V/V
VDD = 2.7 V
-60
VDD = 2.5 V
-70
-80
VDD = 5 V
-90
-100
10
100 k
VDD = 3.6 V
100
1k
10 k
f - Frequency - Hz
-40
-50
VDD = 2.5 V
-60
-70
VDD = 5 V
-80
Inputs ac-grounded,
CI = 1 mF,
-90
-100
10
100 k
VDD = 2.7 V
VDD = 3.6 V
100
RL = 8 W,
Gain = 4 V/V
10 k
1k
f - Frequency - Hz
100 k
Figure 21.
SUPPLY RIPPLE REJECTION RATIO
vs
FREQUENCY- TPA2032D1
SUPPLY RIPPLE REJECTION RATIO
vs
FREQUENCY- TPA2033D1
SUPPLY RIPPLE REJECTION RATIO
vs
FREQUENCY- TPA2034D1
R L = 4 W,
-50
-60
Gain = 2 V/V
VDD = 2.5 V
VDD = 3.6 V
-70
-80
VDD = 5 V
-90
100
1k
10 k
f - Frequency - Hz
-40
R L = 4 W,
-50
-60
Gain = 3 V/V
VDD = 2.7 V
VDD = 2.5 V
-70
-80
-90
-100
10
100 k
-30
Inputs ac-grounded,
CI = 1 mF,
Supply Ripple Rejection Ratio - dB
-40
-30
Inputs ac-grounded,
CI = 1 mF,
VDD = 3.6 V
VDD = 5 V
100
1k
10 k
f - Frequency - Hz
-40
-50
R L = 4 W,
Gain = 4 V/V
VDD = 2.7 V
-60
-70
VDD = 2.5 V
-80
VDD = 5 V
-90
-100
10
100 k
Inputs ac-grounded,
CI = 1 mF,
VDD = 3.6 V
100
1k
10 k
100 k
f - Frequency - Hz
Figure 22.
Figure 23.
Figure 24.
SUPPLY RIPPLE REJECTION RATIO
vs
FREQUENCY - TPA2032D1
SUPPLY RIPPLE REJECTION RATIO
vs
FREQUENCY - TPA2033D1
SUPPLY RIPPLE REJECTION RATIO
vs
FREQUENCY - TPA2034D1
-30
Supply Ripple Rejection Ratio - dB
-40
Inputs Floating,
R L = 8 W,
Gain = 2 V/V
-50
-60
VDD = 2.5 V
-70
-80
VDD = 2.7 V
VDD = 3.6 V
-90
-100
10
VDD = 5 V
100
1k
10 k
f - Frequency - Hz
Figure 25.
100 k
-40
-30
Inputs Floating,
R L = 8 W,
Supply Ripple Rejection Ratio - dB
-30
Supply Ripple Rejection Ratio - dB
-50
R L = 8 W,
Figure 20.
-100
10
8
-40
-30
Inputs ac-grounded,
CI = 1 mF,
Figure 19.
-30
Supply Ripple Rejection Ratio - dB
Supply Ripple Rejection Ratio - dB
-40
-30
Inputs ac-grounded,
CI = 1 mF,
Supply Ripple Rejection Ratio - dB
Supply Ripple Rejection Ratio - dB
-30
SUPPLY RIPPLE REJECTION RATIO
vs
FREQUENCY - TPA2034D1
Supply Ripple Rejection Ratio - dB
SUPPLY RIPPLE REJECTION RATIO
vs
FREQUENCY - TPA2032D1
Gain = 3 V/V
-50
-60
VDD = 2.5 V
-70
VDD = 2.7 V
-80
VDD = 3.6 V
-90
-100
10
VDD = 5 V
100
10 k
1k
f - Frequency - Hz
Figure 26.
Submit Documentation Feedback
100 k
-40
-50
Inputs Floating,
R L = 8 W,
Gain = 4 V/V
VDD = 2.5 V
-60
-70
-80
-90
-100
10
VDD = 2.7 V
VDD = 3.6 V
VDD = 5 V
100
1k
10 k
f - Frequency - Hz
Figure 27.
100 k
TPA2032D1
TPA2033D1
TPA2034D1
www.ti.com
SLOS476 – JUNE 2006
GSM POWER SUPPLY REJECTION
vs
FREQUENCY
0
-20
-40
-60
-80
-100
-120
-140
VO - Output Voltage - dBV
VDD
200 mV/div
VOUT
20 mV/div
t - Time - 2 mS/div
10
-10
-30
-50
-70
-90
-110
-130
-150
VDD Shown in Figure 22
CI = 1 mF,
Inputs ac-Grounded
0 200 400 600 800 1k 1.2k 1.4k 1.6k1.8k 2k
f - Frequency - Hz
Figure 28.
Figure 29.
SUPPLY RIPPLE REJECTION RATIO
vs
DC COMMON MODE VOLTAGE TPA2033D1
SUPPLY RIPPLE REJECTION RATIO
vs
DC COMMON MODE VOLTAGE TPA2034D1
0
-10
-30
-40
-50
VDD = 2.5 V
-60
VDD = 3.6 V
VDD = 5 V
-70
-80
-90
Supply Ripple Rejection Ratio - dB
0
-10
Supply Ripple Rejection Ratio - dB
0
-10
-20
-30
-40
VDD = 2.5 V
VDD = 3.6 V
-50
-60
VDD = 5 V
-70
-80
0.5 1 1.5 2 2.5 3 3.5 4 4.5
DC Common-Mode Voltage - V
5
0
0.5
1 1.5 2 2.5 3 3.5 4 4.5
DC Common-Mode Voltage - V
Figure 30.
COMMON-MODE REJECTION
RATIO
vs
FREQUENCY
-60
VDD = 3.6 V,
-65
VIC = 1 Vpp,
RL = 8 W
-70
-75
-80
-85
10
VDD = 2.5 V
5
100
1k
10 k
f - Frequency - Hz
100 k
VDD = 3.6 V
-30
-40
-50
VDD = 5 V
-60
-70
-80
0.5
1 1.5 2 2.5 3 3.5 4 4.5 5
DC Common-Mode Voltage - V
Figure 31.
Figure 32.
COMMON-MODE REJECTION
RATIO
vs
COMMON-MODE INPUT VOLTAGE
CMRR - Common-Mode Rejection Ratio - dB
0
-20
-90
0
-90
CMRR - Common Mode Rejection Ratio - dB
Supply Ripple Rejection Ratio - dB
SUPPLY RIPPLE REJECTION RATIO
vs
DC COMMON MODE VOLTAGE TPA2032D1
-20
VDD - Supply Voltage - dBV
GSM POWER SUPPLY REJECTION
vs
TIME
-40
-45
-50
-55
-60
VDD = 5 V
VDD = 2.5 V
VDD = 3.6 V
-65
-70
-75
-80
-85
0
0.5 1 1.5 2 2.5 3 3.5 4 4.5
VIC - Common-Mode Input Voltage - V
Figure 33.
Submit Documentation Feedback
5
Figure 34.
9
TPA2032D1
TPA2033D1
TPA2034D1
www.ti.com
SLOS476 – JUNE 2006
APPLICATION INFORMATION
FULLY DIFFERENTIAL AMPLIFIER
The TPA2032D1 is a fully differential amplifier with differential inputs and outputs. The fully differential amplifier
consists of a differential amplifier and a common-mode amplifier. The differential amplifier ensures that the
amplifier outputs a differential voltage on the output that is equal to the differential input times the gain. The
common-mode feedback ensures that the common-mode voltage at the output is biased around VDD/2
regardless of the common-mode voltage at the input. The fully differential TPA2032D1 can still be used with a
single-ended input; however, the TPA2032D1 should be used with differential inputs when in a noisy
environment, like a wireless handset, to ensure maximum noise rejection.
Advantages of Fully Differential Amplifiers
• Input-coupling capacitors not required:
– The fully differential amplifier allows the inputs to be biased at voltage other than mid-supply. The inputs of
the TPA2032D1 can be biased anywhere within the common mode input voltage range listed in the
Recommended Operating Conditions table. If the inputs are biased outside of that range, input-coupling
capacitors are required.
• Midsupply bypass capacitor, C(BYPASS), not required:
– The fully differential amplifier does not require a bypass capacitor. Any shift in the midsupply affects both
positive and negative channels equally and cancels at the differential output.
• Better RF-immunity:
– GSM handsets save power by turning on and shutting off the RF transmitter at a rate of 217 Hz. The
transmitted signal is picked-up on input and output traces. The fully differential amplifier cancels the signal
better than the typical audio amplifier.
COMPONENT SELECTION
Figure 35 shows the TPA2032D1 typical schematic with differential inputs, while Figure 36 shows the
TPA2032D1 with differential inputs and input capacitors. Figure 37 shows the TPA2032D1 with a single-ended
input.
Decoupling Capacitor (CS)
The TPA2032D1 is a high-performance class-D audio amplifier that requires adequate power supply decoupling
to ensure the efficiency is high and total harmonic distortion (THD) is low. For higher frequency transients,
spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor, typically
1µF, placed as close as possible to the device VDD lead works best. Placing this decoupling capacitor close to
the TPA2032D1 is very important for the efficiency of the class-D amplifier, because any resistance or
inductance in the trace between the device and the capacitor can cause a loss in efficiency. For filtering
lower-frequency noise signals, a 10 µF or greater capacitor placed near the audio power amplifier would also
help, but it is not required in most applications because of the high PSRR of this device. Typically, the smaller
the capacitor's case size, the lower the inductance and the closer it can be placed to the TPA2032D1.
Input Capacitors (CI)
The TPA2032D1 does not require input coupling capacitors if the design uses a differential source that is biased
within the common-mode input voltage range. That voltage range is listed in the Recommended Operating
Conditions table. If the input signal is not biased within the recommended common-mode input range, such as in
needing to use the input as a high pass filter, shown in Figure 36, or if using a single-ended source, shown in
Figure 37, input coupling capacitors are required. The same value capacitors should be used on both IN+ and
IN– for best pop performance.
1
fc +
ǒ2p RICIǓ
(1)
The value of the input capacitor is important to consider as it directly affects the bass (low frequency)
performance of the circuit. Speaker response may also be taken into consideration when setting the corner
frequency using input capacitors.
10
Submit Documentation Feedback
TPA2032D1
TPA2033D1
TPA2034D1
www.ti.com
SLOS476 – JUNE 2006
APPLICATION INFORMATION (continued)
Equation 2 is reconfigured to solve for the input coupling capacitance.
1
C +
I
ǒ2p RI f cǓ
(2)
If the corner frequency is within the audio band, the capacitors should have a tolerance of ±10% or better,
because any mismatch in capacitance causes an impedance mismatch at the corner frequency and below.
For a flat low-frequency response, use large input coupling capacitors (1 µF or larger).
To Battery
Internal
Oscillator
VDD
CS
IN−
PWM
_
Differential
Input
H−
Bridge
VO−
VO+
+
IN+
GND
Bias
Circuitry
SHUTDOWN
TPA2032D1
Filter-Free Class D
Figure 35. Typical TPA2032D1 Application Schematic With Differential Input for a Wireless Phone
To Battery
CI
Differential
Input
Internal
Oscillator
VDD
CS
IN−
_
CI
PWM
H−
Bridge
VO−
VO+
+
IN+
GND
SHUTDOWN
Bias
Circuitry
TPA2032D1
Filter-Free Class D
Figure 36. TPA2032D1 Application Schematic With Differential Input and Input Capacitors
Submit Documentation Feedback
11
TPA2032D1
TPA2033D1
TPA2034D1
www.ti.com
SLOS476 – JUNE 2006
APPLICATION INFORMATION (continued)
CI
Single-ended
Input
To Battery
Internal
Oscillator
VDD
IN−
_
PWM
CS
VO−
H−
Bridge
VO+
+
IN+
CI
GND
Bias
Circuitry
SHUTDOWN
TPA2032D1
Filter-Free Class D
Figure 37. TPA2032D1 Application Schematic With Single-Ended Input
BOARD LAYOUT
In making the pad size for the WCSP balls, it is recommended that the layout use nonsolder mask defined
(NSMD) land. With this method, the solder mask opening is made larger than the desired land area, and the
opening size is defined by the copper pad width. Figure 38 and Table 1 show the appropriate diameters for a
WCSP layout. The TPA2032D1 evaluation module (EVM) layout is shown in the next section as a layout
example.
Copper
Trace Width
Solder
Pad Width
Solder Mask
Opening
Copper Trace
Thickness
Solder Mask
Thickness
Figure 38. Land Pattern Dimensions
12
Submit Documentation Feedback
TPA2032D1
TPA2033D1
TPA2034D1
www.ti.com
SLOS476 – JUNE 2006
APPLICATION INFORMATION (continued)
Table 1. Land Pattern Dimensions
SOLDER PAD
DEFINITIONS
COPPER PAD
SOLDER MASK
OPENING
COPPER
THICKNESS
STENCIL
OPENING
STENCIL
THICKNESS
Nonsolder mask
defined (NSMD)
275 µm
(+0.0, –25 µm)
375 µm
(+0.0, –25 µm)
1 oz max (32 µm)
275 µm x 275 µm Sq.
(rounded corners)
125 µm thick
NOTES:
1. Circuit traces from NSMD defined PWB lands should be 75 µm to 100 µm wide in the exposed area inside
the solder mask opening. Wider trace widths reduce device stand off and impact reliability.
2. Recommended solder paste is Type 3 or Type 4.
3. Best reliability results are achieved when the PWB laminate glass transition temperature is above the
operating range of the intended application.
4. For a PWB using a Ni/Au surface finish, the gold thickness should be less 0.5 µm to avoid a reduction in
thermal fatigue performance.
5. Solder mask thickness should be less than 20 µm on top of the copper circuit pattern.
6. Best solder stencil performance is achieved using laser-cut stencils with electro polishing. Use of chemically
etched stencils results in inferior solder paste volume control.
7. Trace routing away from WCSP device should be balanced in X and Y directions to avoid unintentional
component movement due to solder wetting forces.
Component Location
Place all the external components very close to the TPA2032D1. Placing the decoupling capacitor, CS, close to
the TPA2032D1 is important for the efficiency of the class-D amplifier. Any resistance or inductance in the trace
between the device and the capacitor can cause a loss in efficiency.
Trace Width
Recommended trace width at the solder balls is 75 µm to 100 µm to prevent solder wicking onto wider PCB
traces. Figure 39 shows the layout of the TPA2032D1 evaluation module (EVM).
For high current pins (VDD, GND VO+, and VO-) of the TPA2032D1, use 100-µm trace widths at the solder balls
and at least 500-µm PCB traces to ensure proper performance and output power for the device.
For input pins (IN–, IN+, and SHUTDOWN) of the TPA2032D1, use 75-µm to 100-µm trace widths at the solder
balls. IN– and IN+ traces need to run side-by-side to maximize common-mode noise cancellation.
Submit Documentation Feedback
13
TPA2032D1
TPA2033D1
TPA2034D1
www.ti.com
SLOS476 – JUNE 2006
75 mm
100 mm
100 mm
100 mm
375 mm
(+0, -25 mm)
275 mm
(+0, -25 mm)
100 mm
Circular Solder Mask Opening
Paste Mask (Stencil)
= Copper Pad Size
75 mm
100 mm
75 mm
Figure 39. Close Up of TPA2032D1 Land Pattern From TPA2032D1 EVM
EFFICIENCY AND THERMAL INFORMATION
The maximum ambient temperature depends on the heat-sinking ability of the PCB system. The derating factor
for the YZF package is shown in the dissipation rating table. Converting this to θJA:
1
q
+
JA
Derating Factor
(3)
Given θJA (from the Package Dissipation ratings table), the maximum allowable junction temperature (from the
Absolute Maximum ratings table), and the maximum internal dissipation (from Power Dissipation vs Output
Power figures) the maximum ambient temperature can be calculated with the following equation. Note that the
units on these figures are Watts RMS. Because of crest factor (ratio of peak power to RMS power) from 9–15
dB, thermal limitations are not usually encountered.
T Max + T Max * q P
A
J
JA Dmax
(4)
The TPA2032D1 is designed with thermal protection that turns the device off when the junction temperature
surpasses 150°C to prevent damage to the IC. Note that using speakers more resistive than 4-Ω dramatically
increases the thermal performance by reducing the output current and increasing the efficiency of the amplifier.
θJA is a gross approximation of the complex thermal transfer mechanisms between the device and its ambient
environment. If the θJA calculation reveals a potential problem, a more accurate estimate should be made.
Please contact TI for further information.
14
Submit Documentation Feedback
TPA2032D1
TPA2033D1
TPA2034D1
www.ti.com
SLOS476 – JUNE 2006
WHEN TO USE AN OUTPUT FILTER
Design the TPA2032D1 without an output filter if the traces from the amplifier to the speaker are short. Wireless
handsets and PDAs are great applications for this class-D amplifier to be used without an output filter.
The TPA2032D1 passed FCC- and CE-radiated emissions testing with no shielding with speaker trace wires 100
mm long or less. For longer speaker trace wires, a ferrite bead can often be used in the design if failing radiated
emissions testing without an LC filter; and, the frequency-sensitive circuit is greater than 1 MHz. If choosing a
ferrite bead, choose one with high impedance at high frequencies, but very low impedance at low frequencies.
The selection must also take into account the currents flowing through the ferrite bead. Ferrites can begin to
loose effectiveness at much lower than rated current values. Please see the EVM User's Guide for components
used successfully by TI.
Figure 40 shows a typical ferrite-bead output filter.
Ferrite
Chip Bead
VO−
1 nF
Ferrite
Chip Bead
VO+
1 nF
Figure 40. Typical Ferrite Chip Bead Filter
Submit Documentation Feedback
15
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power Wireless www.ti.com/lpw
Mailing Address:
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2006, Texas Instruments Incorporated