DBB03A Baseband ASIC for Dolphin Chipset www.ti.com SWRS030 – JULY 2005 FEATURES • • • • • • Low Supply Voltage Range: 1.8 V to 3.6 V Ultralow-Power Consumption: – Active Mode: 160 µA at 1 MHz, 2.2 V – Standby Mode: 0.9 µA – Off Mode (RAM Retention) : 0.1 µA Contains Frequency-Hopping Firmware for Dolphin Reference Design Firmware Resides in ROM-Based Program Memory and is Fixed Simple UART Interface to an External Host/System Microcontroller Pre-Defined Protocol for Communication with • • • • • • an External Host/System Microcontroller Five Power-Saving Modes Wake-Up From Standby Mode in less than 6 µs 16-Bit RISC Architecture, 125-ns Instruction Cycle Time Serial Communication Interface (USART), Software Selects Asynchronous UART or Synchronous SPI Available in 64-Pin Quad Flat Pack (QFP) For Complete Dolphin Product Description, See the Dolphin Frequency Hopping Spread Spectrum Evaluation Kit Hardware and Software User’s Guide (SLLU090) DESCRIPTION The DBB03A is a baseband ASIC for the "Dolphin" reference design. The firmware for the Dolphin reference design resides in the ROM-based program memory of the DBB03A, and thus can be readily interfaced with a TRF6903 single-chip RF Transceiver to generate a frequency hopping wireless UART "Dolphin" reference design chipset. This is illustrated in Figure 1. The DBB03A baseband ASIC in addition to being a RF baseband processor is also responsible for communications with an external host/system micrcontroller. In a typical end user application, the Dolphin chipset will be connected up to an external host/system microcontroller that will send configuration messages, RF transmission messages into the Dolphin chipset, or receive status, RF messages received from the Dolphin chipset. Any catalog low-cost host/system microcontroller can be interfaced to the Dolphin chipset as long as the Dolphin host interface protocol for communication is adhered to. (See Application Note Dolphin - Frequency Hopping Spread Spectrum Chipset Host Interface Protocol TI Literature SWRA043) Texas Instruments recommends its ultra-low power MSP430 series of microcontrollers to interface with Dolphin. The interface between the DBB03A baseband ASIC and an external host/system microcontroller is a simple UART consisting of RX and TX data lines. (See Application Note Interfacing Dolphin to an External System Microcontroller, TI Literature SWRA045). Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2005, Texas Instruments Incorporated DBB03A Baseband ASIC for Dolphin Chipset www.ti.com SWRS030 – JULY 2005 Host Interface Protocol via UART RF TRF6903 DBB03A Baseband ASIC System Micro Application Layer Data Link Layer MAC Layer PHY Layer Figure 1. DBB03A - Baseband ASIC for the Dolphin Chipset The Wireless UART Dolphin chipset is a true Data-In/RF-out and RF-in/Data-out solution with all aspects of data management and frequency hopping implemented in firmware residing on the DBB03A. As illustrated in Figure 1, the DBB03A baseband ASIC contains the complete firmware for Dolphin (PHYsical, MAC and the Data Link layer), while the application layer protocol is handled by the external Host/System Microcontroller. AVAILABLE OPTIONS 2 TA PACKAGE ORDER NUMBER -40°C to 85°C Plastic 64-pin QFP (PM) DBB03A IPM DBB03A Baseband ASIC for Dolphin Chipset www.ti.com SWRS030 – JULY 2005 AVCC DVSS AV SS P6.2 P6.1 P6.0 RST/NMI TCK TMS TDI/TCLK TDO/TDI XT2IN XT2OUT P5.7/TBOUTH PM PACKAGE (TOP VIEW) 1 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 33 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 P5.4/MCLK P5.3 P5.2 P5.1 P5.0 P4.7/TBCLK P4.6 P4.5 P4.4 P4.3 P4.2/TB2 P4.1/TB1 P4.0/TB0 P3.7 P3.6 P3.5/URXD0 P1.5/TA0 P1.6/TA1 P1.7/TA2 P2.0/ACLK P2.1/TAINCLK P2.2/CAOUT/TA0 P2.3/CA0/TA1 P2.4/CA1/TA2 P2.5/Rosc P2.6 P2.7/TA0 P3.0/STE0 P3.1/SIMO0 P3.2/SOMI0 P3.3/UCLK0 P3.4/UTXD0 DVCC P6.3 P6.4 P6.5 P6.6 P6.7 NC XIN XOUT NC NC P1.0/TACLK P1.1/TA0 P1.2/TA1 P1.3/TA2 P1.4/SMCLK P5.6/ACLK P5.5/SMCLK PIN DESIGNATION, DBB03A Baseband ASIC NC − No internal connection 3 DBB03A Baseband ASIC for Dolphin Chipset www.ti.com SWRS030 – JULY 2005 FUNCTIONAL BLOCK DIAGRAMS: DBB03A XIN XOUT/TCLK DVCC DVSS AVCC AVSS P1 RST/NMI P2 8 ROSC Oscillator XT2IN System Clock XT2OUT ACLK 16KB ROM 512B RAM SMCLK 8KB ROM 256B RAM I/O Port 1/2 16 I/Os, with Interrupt Capability P3 8 P4 8 I/O Port 3/4 16 I/Os P5 8 P6 8 8 I/O Port 5/6 16 I/Os MCLK Test MAB, 4 Bit MAB,MAB, 16 Bit16-Bit JTAG CPU MCB Emulation Module Incl. 16 Reg. Bus Conv MDB, 16-Bit MDB, 16 Bit MDB, 8 Bit 4 TMS Watchdog Timer TCK TDI 15/16-Bit TDO/TDI Timer_B3 Timer_A3 3 CC Reg Shadow Reg 3 CC Reg POR Comparator A USART0 UART Mode SPI Mode DEVICE INFORMATION TERMINAL FUNCTIONS TERMINAL I/O DESCRIPTION NAME NO. AVCC 64 Supply voltage, positive terminal. AVCC and DVCC are internally connected together. AVSS 64 Supply voltage, negative terminal. AVSS and DVSS are internally connected together. DVCC 1 Supply voltage, positive terminal. AVCC and DVCC are internally connected together. DVSS 63 P1.0/TACLK 12 I/O General-purpose digital I/O pin/Timer_A, clock signal TACLK input P1.1/TA0 13 I/O General-purpose digital I/O pin/Timer_A, capture: CCI0A input, compare: Out0 output P1.2/TA1 14 I/O General-purpose digital I/O pin/Timer_A, capture: CCI1A input, compare: Out1 output P1.3/TA2 15 I/O General-purpose digital I/O pin/Timer_A, capture: CCI2A input, compare: Out2 output P1.4/SMCLK 16 I/O General-purpose digital I/O pin/SMCLK signal output P1.5/TA0 17 I/O General-purpose digital I/O pin/Timer_A, compare: Out0 output P1.6/TA1 18 I/O General-purpose digital I/O pin/Timer_A, compare: Out1 output P1.7/TA2 19 I/O General-purpose digital I/O pin/Timer_A, compare: Out2 output P2.0/ACLK 20 I/O General-purpose digital I/O pin/ACLK output P2.1/TAINCL K 21 I/O General-purpose digital I/O pin/Timer_A, clock signal at INCLK P2.2/CAOUT/ TA0 22 I/O General-purpose digital I/O pin/Timer_A, capture: CCI0B input/Comparator_A output P2.3/CA0/TA 1 23 I/O General-purpose digital I/O pin/Timer_A, compare: Out1 output/Comparator_A input P2.4/CA1/TA 2 24 I/O General-purpose digital I/O pin/Timer_A, compare: Out2 output/Comparator_A input P2.5/ROSC 25 I/O General-purpose digital I/O pin/input for external resistor defining the DCO nominal frequency P2.6 26 I/O General-purpose digital I/O pin 4 Supply voltage, negative terminal. AVSS and DVSS are internally connected together. DBB03A Baseband ASIC for Dolphin Chipset www.ti.com SWRS030 – JULY 2005 DEVICE INFORMATION (continued) TERMINAL FUNCTIONS (continued) TERMINAL NAME NO. I/O DESCRIPTION P2.7/TA0 27 I/O General-purpose digital I/O pin/Timer_A, compare: Out0 output P3.0/STE0 28 I/O General-purpose digital I/O pin/slave transmit enable - USART0/SPI mode P3.1/SIMO0 29 I/O General-purpose digital I/O pin/slave in/master out of USART0/SPI mode P3.2/SOMI0 30 I/O General-purpose digital I/O pin/slave out/master in of USART0/SPI mode P3.3/UCLK0 31 I/O General-purpose digital I/O pin/external clock input - USART0/UART or SPI mode, clock output - USART0/SPI mode P3.4/UTXD0 32 I/O General-purpose digital I/O pin/transmit data out - USART0/UART mode P3.5/URXD0 33 I/O General-purpose digital I/O pin/receive data in - USART0/UART mode P3.6 34 I/O General-purpose digital I/O pin P3.7 35 I/O General-purpose digital I/O pin P4.0/TB0 36 I/O General-purpose digital I/O pin/Timer_B, capture: CCI0A/B input, compare: Out0 output P4.1/TB1 37 I/O General-purpose digital I/O pin/Timer_B, capture: CCI1A/B input, compare: Out1 output P4.2/TB2 38 I/O General-purpose digital I/O pin/Timer_B, capture: CCI2A/B input, compare: Out2 output P4.3 39 I/O General-purpose digital I/O pin P4.4 40 I/O General-purpose digital I/O pin P4.5 41 I/O General-purpose digital I/O pin P4.6 42 I/O General-purpose digital I/O pin P4.7/TBCLK 43 I/O General-purpose digital I/O pin/Timer_B, clock signal TBCLK input P5.0 44 I/O General-purpose digital I/O pin P5.1 45 I/O General-purpose digital I/O pin P5.2 46 I/O General-purpose digital I/O pin P5.3 47 I/O General-purpose digital I/O pin P5.4/MCLK 48 I/O General-purpose digital I/O pin/main system clock MCLK output P5.5/SMCLK 49 I/O General-purpose digital I/O pin/submain system clock SMCLK output P5.6/ACLK 50 I/O General-purpose digital I/O pin/auxiliary clock ACLK output P5.7/TBOUT H 51 I/O General-purpose digital I/O pin/switch all PWM digital output ports to high impedance Timer_B7 TB0 to TB2 P6.0 59 I/O General-purpose digital I/O pin P6.1 60 I/O General-purpose digital I/O pin P6.2 61 I/O General-purpose digital I/O pin P6.3 2 I/O General-purpose digital I/O pin P6.4 3 I/O General-purpose digital I/O pin P6.5 4 I/O General-purpose digital I/O pin P6.6 5 I/O General-purpose digital I/O pin P6.7 6 I/O General-purpose digital I/O pin RST/NMI 58 I Reset input, nonmaskable interrupt input port TCK 57 I Test clock. TCK is the clock input port for device programming test. TDI/TCLK 55 I Test data input or test clock input. TDI is used as a data input port. The device protection fuse is connected to TDI. TDO/TDI 54 I/O TMS 56 I Test data output port. TDO/TDI data output Test mode select. TMS is used as an input port for device test. NC 7, 10, 11 No internal connection XIN 8 I Input port for crystal oscillator XT1. Standard or watch crystals can be connected. XOUT 9 O Output terminal of crystal oscillator XT1 XT2IN 53 I Input port for crystal oscillator XT2. Only standard crystals can be connected. XT2OUT 52 O Output terminal of crystal oscillator XT2 5 DBB03A Baseband ASIC for Dolphin Chipset SWRS030 – JULY 2005 6 www.ti.com PACKAGE OPTION ADDENDUM www.ti.com 15-Jun-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty DBB03AIPM ACTIVE LQFP PM 64 160 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR DBB03AIPMR ACTIVE LQFP PM 64 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 MECHANICAL DATA MTQF008A – JANUARY 1995 – REVISED DECEMBER 1996 PM (S-PQFP-G64) PLASTIC QUAD FLATPACK 0,27 0,17 0,50 0,08 M 33 48 49 32 64 17 0,13 NOM 1 16 7,50 TYP Gage Plane 10,20 SQ 9,80 12,20 SQ 11,80 0,25 0,05 MIN 0°– 7° 0,75 0,45 1,45 1,35 Seating Plane 0,08 1,60 MAX 4040152 / C 11/96 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Falls within JEDEC MS-026 May also be thermally enhanced plastic with leads connected to the die pads. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Mailing Address: Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2006, Texas Instruments Incorporated