IRF9240 IRFN9240 IRF9240SMD MECHANICAL DATA Dimensions in mm (inches) 25.15 (0.99) 26.67 (1.05) 6.35 (0.25) 9.15 (0.36) IRF9240 1.52 (0.06) 3.43 (0.135) D 2 22.23 (0.875) max. 0.97 (0.060) 1.10 (0.043) 16.64 (0.655) 17.15 (0.675) 29.9 (1.177) 30.4 (1.197) 38.61 (1.52) 39.12 (1.54) 10.67 (0.42) 11.18 (0.44) 1 P–CHANNEL POWER MOSFET G 3 (case) 3.84 (0.151) 4.09 (0.161) S 7.92 (0.312) 12.70 (0.50) TO–3 Package (TO-204AA) Pin 2 – Source 4 .1 4 (0 .1 6 3 ) 3 .8 4 (0 .1 5 1 ) 1 3 .6 0 (0 .1 4 2 ) M a x . IRFN9240SMD 3 7 (0 8 (0 8 (0 8 (0 .3 8 .3 6 .4 5 .4 4 • AVAILABLE IN TO-3 (TO-204AA) AND CERAMIC SURFACE MOUNT SMD1 (TO276AB)PACKAGE 1 ) 9 ) 6 ) 4 ) 0 .5 0 (0 .0 2 0 ) 0 .2 6 (0 .0 1 0 ) SMD1 (TO276AB) Pin 1 – Gate • HIGH VOLTAGE • INTEGRAL PROTECTION DIODE 2 9 .6 9 .3 1 1 .5 1 1 .2 FEATURES • P–CHANNEL POWER MOSFET 0 .8 9 (0 .0 3 5 ) m in . 3 .7 0 (0 .1 4 6 ) 3 .4 1 (0 .1 3 4 ) 1 0 .6 9 (0 .4 2 1 ) 1 0 .3 9 (0 .4 0 9 ) 0 .7 6 (0 .0 3 0 ) m in . 3 .7 0 (0 .1 4 6 ) 3 .4 1 (0 .1 3 4 ) Pin 3 – Drain 1 6 .0 2 (0 .6 3 1 ) 1 5 .7 3 (0 .6 1 9 ) Pin 1 – Gate Pin 2 – Drain Pin 3 – Source Note: IRF9240SMD also available with pins 1 and 3 reversed on SMD 1 package. ABSOLUTE MAXIMUM RATINGS (Tcase = 25°C unless otherwise stated) VDSS VDGR VGS ID IDM PD Tj Tstg Drain – Source Voltage Drain – Gate Voltage (RGS = 20KΩ) Gate – Source Voltage Continuous Drain Current @ Tcase = 25°C @ Tcase = 100°C Pulsed Drain Current Max. Power Dissipation @ Tcase = 25°C Linear Derating Factor Operating Junction and Storage Temperature Range –200V –200V ±20V –11A –7.0A –44A 125W 1W / °C –55 to 150°C Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: [email protected] Website: http://www.semelab.co.uk Document Number 3345 Issue 2 IRF9240 IRFN9240 IRF9240SMD ELECTRICAL RATINGS (Tcase = 25°C unless otherwise stated) BVDSS Characteristic Drain – Source Breakdown Voltage VGS(TH) Gate Threshold Voltage IGSS IDSS Test Conditions VGS = 0V , ID = –1mA Min. –200 VDS = VGS , ID = –250µA –2 Typ. RDS(ON) nA Gate – Source Leakage Current (reverse) VGS = 20V 100 nA VDS = -160V , VGS = 0V –25 µA –1 mA VDS = -160V Zero Gate Voltage Drain Current VDS > ID(ON) x RDS(ON) Max On State Drain Current 1 VGS = –10V Ciss Input capacitance Output capacitance Crss Reverse transfer capacitance Qg Total Gate Charge Qgs Gate – Source Charge Qgd Gate – Drain (“Miller”) Charge td(on) Turn–on Delay Time –11 VGS = –10V , ID = –7A Static Drain – Source On-State Resistance Coss tf V –100 Forward Transconductance 1 td(off) –4 VGS = –20V gfs tr Unit V Gate – Source Leakage Current (forward) VGS = 0V , Tcase = 125°C ID(ON) Max. VDS > ID(ON) x RDS(ON) Max ID = –7A A 0.35 4 6 VGS = 0V 1200 VDS = –25V 570 f = 1MHz 81 60 ID = –11A 3.0 15 VDS = -100V 4.5 38 nC 35 85 85 ZO = 9.1Ω Fall Time pF 28 ID = –11A Turn-off Delay Time Ω S VGS = –10V VDD = -100V Rise Time 0.5 ns 65 LD Internal Drain Inductance 5.0 nH LS Internal Source Inductance 12.5 nH THERMAL CHARACTERISTICS Characteristic RθJC Junction to Case RθJA TL Min. Junction to Ambient (TO-3 package only) Max. Lead Temperature 0.063 ” from case for 10 sec. (TO-3 package only) SOURCE – DRAIN DIODE RATINGS AND CHARACTERISTICS Characteristic Continuous Source Current (Body Diode) IS Pulsed Source Current1 (Body Diode) I Test Conditions Typ. 30 300 Min. Typ. Diode Forward Voltage2 trr Reverse Recovery Time Qrr Reverse Recovery Charge 1) Pulse Test: Pulse Width < 300µS , Duty Cycle ≤ 2% VGS = 0V , IS = – 11A Max. –11 –4.6 Tcase = 25°C IF = –11A , dlF / dt = 100A/µs Tj = 25°C IF = –11A , dlF / dt = 100A/µs Tj = 25°C °C/W °C –44 SM VSD Max. Unit 1.0 °C/W Unit A V 270 ns 2.0 µC 2) Repetitive Rating: Pulse Width limited by maximum junction temperature. Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: [email protected] Website: http://www.semelab.co.uk Document Number 3345 Issue 2