PSP-240 Series 240W Single Phase Industrial DIN Rail Power Supply F ea tures : U nivers a l A C i nput / F ull ra nge B uilt in a ctive P F C f unction, P F >0.95 P rotections :S hort circuit/O ver loa d/O ver v olta ge/O ver tempera ture C ooling by f ree a ir c onvection C a n be i ns ta lled on D IN r a il T S -35/7.5 o r 1 5 U L 5 08(indus tria l c ontrol e quipment)a pproved L E D i ndica tor for power o n 100% f ull loa d burn-in tes t F ixed s witching frequency a t 100K Hz 3 y ea rs w a rra nty R SPECIFICATION MODEL OUTPUT INPUT PSP-24024 PSP-24048 DC VOLTAGE 24V 48V RATED CURRENT 10A 5A CURRENT RANGE 0 ~ 10A 0 ~ 5A RATED POWER 240W 240W RIPPLE & NOISE (max.) Note.2 80mVp-p 150mVp-p VOLTAGE ADJ . R ANGE 48 ~ 53V 1.0% 24 ~ 28V VOLTAGE TOLERANCE Note.3 1.0% LINE R EGULATION 0.5% LOAD REGULATION 1.0% 0.5% 1.0% SETUP, R ISE, HOLD TIME 800ms, 40ms, 20ms /230VAC VOLTAGE R ANGE 85 ~ 264VAC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR EFFICIENCY (Typ.) PF>0.95/230VAC 84% AC CURRENT INRUSH CURRENT (max.) 2.8A/115V AC LEAKAGE C URRENT OVER L OAD PROTECTION OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE 8 00ms, 40ms, 20ms /115VAC at full load 1 20 ~ 370VDC P F>0.98/115VAC at full load 85% 1.4A/230V AC COLD START 27A/115V AC <3.5mA / 240VAC 45A/230V AC 105 ~ 150% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed 54 ~ 60V 30 ~ 36V Protection type : Shut down o/p voltage, re-power on to recover 100 5 (TSW1)Detect on heat sink of power transistor Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -10 ~ +70 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.03%/ (0 ~ 50 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL508, UL60950-1, EN60950 Approved I/P-O/P:3KVAC I /P-FG:1.5KVAC O/P-FG:0.5KVAC SAFETY & ISOLATION RESISTANCE EMC (Note 4) I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC EMI CONDUCTION & RADIATION Compliance to EN55011,EN55022 (CISPR22) Class B Compliance to EN61000-3-2,-3 HARMONIC CURRENT EMS IMMUNITY MTBF OTHERS DIMENSION PACKING NOTE Compliance to EN61000-4-2,3,4,5,6,8,1 1, ENV50204, EN55024, EN61000-6-2 (EN50082-2) Heavy industry level, criteria A 105.5Khrs min. MIL-HDBK-217F (25 ) 125.5*125.2*100mm (W*H*D) 1.2Kg; 20pcs/14.4Kg/1.2CUFT 1. A ll parameters N OT s pecially mentioned a re measured a t 230VAC i nput, r ated load a nd 25 of ambient temperature. 2. R ipple & n oise a re measured a t 20MHz o f bandwidth by using a 1 2" twisted pair-wire terminated with a 0 .1uf & 4 7uf parallel capacitor. 3. T olerance : i ncludes s et up tolerance, line regulation a nd load regulation. 4. T he power s upply is c onsidered a c omponent which will be installed into a f inal equipment. T he final equipment must be re-confirmed that it still meets E MC d irectives. 35 Royal Road, Flemington, NJ 08822-6000 • (tel.) 908-806-9400 • (fax) 908-806-9490 • www.altechcorp.com PSP-240 Series 240W Single Output Industrial DIN Rail Power Supply Mechanical Specification 100 125.2 +V ADJ. 1 2 3 4 TB2 125.5 LE D 1 2 3 TB1 35 ADMISSIBLE DIN-RAIL:TS35/7.5 OR TS35/15 Terminal Pin. No Assignment (TB1) Pin No. 1 2 3 Terminal Pin. No Assignment (TB2) Assignment FG AC/N AC/L Pin No. 1,2 3,4 Output Derating Assignment DC OUTPUT +V DC OUTPUT -V Output derating VS input voltage Ta=25 100 100 230VAC 90 80 80 70 110VAC LOAD (%) LOAD (%) 60 40 20 60 50 40 -10 0 10 20 30 40 AMBIENT TEMPERATURE ( 50 55 60 ) 70 (VERTICAL) Vin: -- 230VAC 110VAC 85 100 110 135 155 230 264 INPUT VOLTAGE (V) 60Hz 35 Royal Road, Flemington, NJ 08822-6000 • (tel.) 908-806-9400 • (fax) 908-806-9490 • www.altechcorp.com