ALTECH PSP-480S

PSP-480S Series
480W Single Phase Industrial DIN Rail Power Supply
F ea tures :
AC i nput ra nge s electa ble b y s witch
B uilt-in pa s s ive P F C f unction c omplia nce to E N61000-3-2
High e fficiency 8 9% a nd low dis s ipa tion
P rotections :S hort circuit/O ver loa d/O ver v olta ge/O ver tempera ture
C ooling by f ree a ir c onvection
B uilt-in c ons ta nt current limiting circuit
C a n be i ns ta lled on D IN r a il T S -35/7.5 o r 1 5
U L 5 08(indus tria l c ontrol e quipment)a pproved
E N61000-6-2(E N50082-2) i ndus tria l immunity l evel
100% f ull loa d burn-in tes t
3 y ea rs w a rra nty
R
SPECIFICATION
MODEL
OUTPUT
PSP-48024
PSP-48048
DC VOLTAGE
24V
48V
RATED CURRENT
20A
10A
CURRENT RANGE
0 ~ 20A
0 ~ 10A
RATED POWER
480W
480W
RIPPLE & NOISE (max.) Note.2 120mVp-p
120mVp-p
VOLTAGE ADJ . R ANGE
48 ~ 55V
1.0%
24 ~ 28V
VOLTAGE TOLERANCE Note.3 1.0%
LINE R EGULATION
0.5%
0.5%
LOAD REGULATION
1.0%
1.0%
SETUP, R ISE, HOLD TIME
1200ms, 40ms, 20ms/230VAC, 115VAC at full load
VOLTAGE R ANGE
90 ~ 132VAC/180 ~ 264VAC by switch
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR
INPUT
254 ~ 370VDC
0.7/230VAC only
EFFICIENCY (Typ.)
89%
AC CURRENT
INRUSH CURRENT (max.)
8A/115V AC 3.3A/230V AC
COLD START 27A/115V AC 4.5A/230V AC
LEAKAGE C URRENT
OVER L OAD
PROTECTION OVER VOLTAGE
OVER TEMPERATURE
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
SAFETY STANDARDS
WITHSTAND VOLTAGE
<3.5mA / 240VAC
105 ~ 150% rated output power
Protection type : Constant current limiting, recovers automatically after fault condition is removed
59 ~66V
30 ~ 36V
Protection type : Shut down o/p voltage, re-power on to recover
100 5 (TSW : Detect on heatsink of power switch)
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
-20 ~ +70 (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-40 ~ +85 , 10 ~ 95% RH
0.03%/ (0 ~ 50
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
UL508, EN60950 Approved, UL 60950-1
I/P-O/P:3KVAC I /P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
SAFETY & ISOLATION RESISTANCE
EMI CONDUCTION & RADIATION Compliance to EN55011 (CISPR11), E N55022 (CISPR22), E N61204-3 Class B
EMC
(Note 4)
HARMONIC CURRENT
EMS IMMUNITY
MTBF
Compliance to EN61000-3-2,-3
Compliance to EN61000-4-2,3,4,5,6,8,11, ENV50204, EN61204-3, EN61000-6-2 (EN50082-2) Heavy industry level, criteriaA
187.9Khrs min. MIL-HDBK-217F (25 )
OTHERS
DIMENSION
PACKING
227*125.2*100mm (W*H*D)
2.6Kg; 6pcs / 16.6Kg / 1.75CUFT
NOTE
1. A ll parameters N OT s pecially mentioned a re measured a t 230VAC i nput, r ated load a nd 25 of ambient temperature.
2. R ipple & n oise a re measured a t 20MHz o f bandwidth by using a 1 2" twisted pair-wire terminated with a 0 .1uf & 4 7uf parallel capacitor.
3. T olerance : i ncludes s et up tolerance, line regulation a nd load regulation.
4. T he power s upply is c onsidered a c omponent which will be installed into a f inal equipment. T he final equipment must be re-confirmed that it still meets
E MC d irectives.
35 Royal Road, Flemington, NJ 08822-6000 • (tel.) 908-806-9400 • (fax) 908-806-9490 • www.altechcorp.com
PSP-480S Series
480W Single Phase Industrial DIN Rail Power Supply
Mechanical Specification
100
56.6
227
10 6
125.2
12
230VAC
115VAC
TB1
3 2 1
LE D
TB2
4 3 2 1
+V ADJ.
35
ADMISSIBLE DIN-RAIL:TS35/7.5 OR TS35/15
TB1 Terminal Pin. No Assignment
Pin No.
1
2
3
TB2 Terminal Pin. No Assignment
Assignment
AC/L
AC/N
FG
Pin No.
1,2
3,4
Derating Curve
Output Derating VS Input Voltage
100
100
180 ~ 264VAC
90 ~ 132VAC
90
80
80
70
LOAD (%)
60
LOAD (%)
Assignment
DC OUTPUT +V
DC OUTPUT -V
40
20
-20
0
10
20
30
40
AMBIENT TEMPERATURE (
50
)
60
70 (VERTICAL)
60
50
40
90
180
100
190
115
230
132
264
INPUT VOLTAGE (V) 60Hz
35 Royal Road, Flemington, NJ 08822-6000 • (tel.) 908-806-9400 • (fax) 908-806-9490 • www.altechcorp.com