Version : 8.0 TECHNICAL SPECIFICATION MODEL NO. : PD064VT4 Customer’s Confirmation Customer PD064VT4 By PVI’s Confirmation Confirmed By Prepared By FOR MORE INFORMATION: AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA, 92656 Http://www.AZDISPLAYS.com Date: July 11, 2007 This technical specification is subject to change without notice. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:1 PD064VT4 Revision History Rev. Eng. 1.0 1.1 1.2 1.3 1.4 1.5 蔡弘毅 1.6 蔡弘毅 8.0 黃秀晶 Issued Date Revised Contents Mar 11,2004 New Mar 12,2004 Modify Page 3. Mechanical Specifications (Weight from 270g to 340g ) Page 4. Mechanical Drawing of TFT-LCD Module (Module with back cover) Nov 01,2004 Modify Page7: 7-2)Recommended Operation Condition for backlight Kick off voltage(25℃) from 790 to 970 Add: Kick-off voltage(0℃) Page22: Packing drawing Jan 11,2005 Remove Page 20: Indication of Lot Number Label Add Page 20: Reliability (Note the protective film must be remove before temperature test) Dec 05,2005 Page4 Mechanical Drawing of TFT-LCD Module 1.Add screw torsion SPEC.(1.5kgf-cm , Max) 2.Modify switch1 Pin NO. from 9 pins to 8 Pins 3.Modify switch1 Pin NO. from 3 pins to 2 Pins Page14 7-8)Control Board Dip switch Format SW1-2 (Rework): form Default(ON) modify to Default(OFF) SW1-3 (Rework) :form Default(OFF) modify to Default(ON) SW1-4 (Rework): form Default(OFF) modify to Default(ON) Apr 28 2006, Page8: 7-4)Input/ Output signal timing chart Hsync (Back-porch) Typ. From 48tc modify to 46tc Hsync(Front-porch) Typ. From 16tc modify to 18tc Hsync(Hpw+Hbp) Typ. From 144 tc modify to 142 tc Page14 7-8)Control Board Dip switch Format SW1-2 (Rework): form Default(OFF) modify to Default(ON) SW1-3 (Rework) :form Default(ON) modify to Default(OFF) SW1-4 (Rework): form Default(ON) modify to Default(OFF) May 23, 2006 Page 16 9. Optical Characteristic 9-1) Specification : lamp life time from 20,000(typ)hrs modify to 50,000 (Min) Remove “Revision History” from Page23 to Page2 July 11, 2007 Modify Page2 Revision from 1.7 to 8.0 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:2 PD064VT4 TECHNICAL SPECIFICATION CONTENTS NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 ITEM Cover Revision History Contents Application Features Mechanical Specifications Mechanical Drawing of TFT-LCD module Input / Output Terminals Absolute Maximum Ratings Electrical Characteristics Power On Sequence Optical Characteristics Handling Cautions Reliability Test Block Diagram Packing PAGE 1 2 3 4 4 4 5 6 7 8 15 16 19 20 21 22 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:3 PD064VT4 1. Application This product applies computer peripheral, industrial meter, image communication and multi-media. 2. Features . Compatible with VGA-480, VGA-400, VGA-350 mode . Support the DENB mode . Pixel in stripe configuration . Slim and compact . Display Colors: 262,144 colors . Image Reversion: Up/Down and Left/Right . Backlight lamps are Replaceable 3. Mechanical Specifications Parameter Screen Size Display Format Active Area Pixel Pitch Pixel Configuration Surface Treatment Outline Dimension Weight Gray scale inversion direction Specifications 6.4 (diagonal) 640×(R,G,B )×480 129.6 (H)×97.44 (V) 0.2025 (H)×0.203 (V) Stripe Anti – Glare &Wide View film 175.4 (W)×126.9 (H)×12.5 (D) (Typ.) 340±10 6 o’clock [ ref to Page 16 viewing angle ] Unit inch dot mm mm mm g The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:4 PD064VT4 4. Mechanical Drawing of TFT-LCD Module The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:5 PD064VT4 5. Input / Output Terminals 5-1) TFT-LCD Panel Driving LCD module connector (Reference)-DF9A-31P-1V Pin No. Symbol Function 1 GND Ground (0V) 2 CLK Clock Signal for Sampling Image Digital Data 3 Hsync Horizontal Synchronous Signal 4 Vsync Vertical Synchronous Signal 5 GND Ground (0V) 6 R0 Red Image Data Signal (LSB) 7 R1 Red Image Data Signal 8 R2 Red Image Data Signal 9 R3 Red Image Data Signal 10 R4 Red Image Data Signal 11 R5 Red Image Data Signal (MSB) 12 GND Ground (0V) 13 G0 Green Image Data Signal (LSB) 14 G1 Green Image Data Signal 15 G2 Green Image Data Signal 16 G3 Green Image Data Signal 17 G4 Green Image Data Signal 18 G5 Green Image Data Signal (MSB) 19 GND Ground (0V) 20 B0 Blue Image Data Signal (LSB) 21 B1 Blue Image Data Signal 22 B2 Blue Image Data Signal 23 B3 Blue Image Data Signal 24 B4 Blue Image Data Signal 25 B5 Blue Image Data Signal (MSB) 26 GND Ground (0V) 27 DENB Enable 28 29 30 31 VCC VCC R/L U/D DC +5.0V Power Supply DC +5.0V Power Supply Horizontal Image Shift-direction Select Signal Vertical Image Shift-direction Select Signal Remark Note 5-1 Note 5-1 Note 5-2 Note 5-3 Note 5-3 Note 5-4 Note 5-5 Note 5-1 : The relationship between DENB & SYNC. mode 1. DENB mode with the top priority. 2. When working with the SYNC. mode , the TFT-LCD module is compatible with three kinds of VGA timing . They are VGA-480 , VGA-400 and VGA-350 mode . The polarization of Hsync and Vsync determine the timings. Mode DENB SYNC. Hsync Polarization Don’t care Vsync Polarization Don’t care VGA-480 VGA-400 VGA-350 Negative / Positive Negative / Positive Negative Positive Positive Negative The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:6 PD064VT4 Note 5-2 : DENB input signal. If customer wanted to off the DENB mode , you must keep the DENB (pin 27) always High or Low. 800 tc 640 tc DENB (tc: the period of sampling clock) Note 5-3 : VCC (TYP.)=+5V Note 5-4 , 5-5 : The definitions of U/D & R/L R/L(PIN 30)= High , U/D(PIN 31)= Low R/L(PIN 30)= Low , U/D(PIN 31)= High 6. Absolute Maximum Ratings : The followings are maximum values , which if exceeded, may cause faulty operation or damage to the unit. GND=0V, Ta=25℃ Parameters Symbol MIN. MAX. Unit Remark Supply Voltage VCC -0.3 +7.0 V Input Signals Voltage Vsig -0.3 VCC+0.3 V Note 6-1 Note 6-1 : Input signals include CLK , Hsync , Vsync , DENB , R[0:5] , G[0:5] and B[0:5]. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:7 PD064VT4 7. Electrical Characteristics 7-1) Recommended Operating Condition for TFT-LCD panel : Parameters Supply Voltage Supply Input Ripple Voltage Input Signals Voltage (High) Input Signals Voltage (Low) Symbol VCC VCCRP VIH VIL GND = 0V , Ta = 25℃ Min. Typ. Max. Unit Remark +4.75 +5.0 +5.25 V 0.1 Vp-p VCC=+5V +2.6 V +0.5 V 7-2) Recommended Operating Condition for backlight: Item Lamp Current Lamp Voltage Lamp frequency Starting voltage(25℃) (Reference Value) Starting voltage(0℃) (Reference Value) Symbol IL VL PL Min. Typ. Unit mA Vrms KHz Ta = 25℃ Remark Note 7-1 IL=6mA Note 7-2 3 330 - 6 360 40 Max. 7 390 - VS - 475 523 Vrms Note 7-3 VS - 620 682 Vrms Note 7-3 Note 7-1 : In order to satisfy the quality of B/L , no matter use what kind of inverter , the output lamp current must between Min. and Max. to avoid the abnormal display image caused by B/L. Note 7-2: The waveform of lamp driving voltage should be as closed to a perfect SIN wave as possible. Note 7-3 : The” Max of starting voltage ” means the minimum voltage of inverter to turn on the CCFL. and it should be applied to the lamp for more than 1 second to start up. Otherwise the lamp may not be turned on. Backlight driving connector: JST BHR-03VS-1 , 3 Pins, Pitch : 4 mm Pin No Symbol Description Remark 1 VL1 Input terminal (Hi voltage side) 2 NC No Connection 3 VL2 Input terminal (Low voltage side) Note 7-4 Note 7-4 : Low voltage side of backlight inverter connects with ground of inverter circuits. 7-3) Power Consumption Parameters Current Dissipation LCD Panel Power consumption (W/O B/L) Backlight Power Consumption Symbol ICC - Typ. 100 0.5 4.32 Max. 120 0.6 - Unit mA W W Remark VCC =+5V Note 7-5 Note 7-5 : Backlight lamp power consumption is calculated by IL×VL. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:8 PD064VT4 7-4) Input / Output signal timing chart Parameters CLK Hsync Symbol Fc=1/tc tc Format All All Period Hp All Display period Pulse width Back-porch Front-porch Hpw+Hbp Hsync-CLK Vsync-Hsync Hd Hpw Hbp Hfp All All All All All All All Frequency Dcd Ddc Typ. 25.175 40 31.778 800 640 96 46 18 142 0 16.8 525 14.3 449 14.3 449 480 400 350 2 33 35 60 10 12 37 35 37 62 - Max. 139 139 151 Tc-10 200 800 480 510 35 35 38 63 38 40 65 - Unit MHz ns us tc tc tc tc tc tc ns tc ms Hp ms Hp ms Hp 480 400 350 All 480 400 350 480 400 350 480 400 350 All All Min. 12 12 136 10 0 515 446 447 2 2 2 2 1 1 1 31 33 58 10 10 T1 All 780 800 900 tc T2 All - 640 - tc T3 All - 480 - T1 T4 All 515 525 800 T1 Hhc Hvh 480 Period Vp 400 350 Vsync Display period Vdp Pulse width Vpw Back-porch Vbp Front-porch Vfp Vpw+Vbp Data DENB CLK-DATA DATA-CLK Horizontal scanning period Horizontal display period Vertical display period Frame cycling period Note Note 7-6 Hp Hp Hp Hp Hp ns ns Note 7-6 : tc is the period of sampling clock. In case of low-frequency , the image-flicker may occur. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:9 PD064VT4 7-5) Display Time Range (1) Vertical Timing : Hsync Hvh Vsync (2) Horizontal Timing : Hsync Hhc tc CLK DATA R0~R5 , G0~G5 , B0~B5 Dcd Ddc (3) DENB Timing : DENB T1 T2 T3 1 480 1 2 3 DENB T4 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:10 PD064VT4 (4) Detail of Horizontal Timing : Hp Hpw Hsync Hbp Hdp Hfp Display period (a) VGA-480 Mode (Hsync = Positive / Negative Polarization) Item A B C D E Description Horizontal Width Horizontal B-Porch Horizontal Display Horizontal F-Porch Horizontal Total Clock Cycles 96 48 640 16 800 Time 3.813 μs 1.907 μs 25.422 μs 0.636 μs 31.778 μs Clock Cycles 96 48 640 16 800 Time 3.813 μs 1.907 μs 25.422 μs 0.636 μs 31.778 μs Clock Cycles 96 48 640 16 800 Time 3.813 μs 1.907 μs 25.422 μs 0.636 μs 31.778 μs (b) VGA-400 Mode (Hsync = Negative Polarization) Item A B C D E Description Horizontal Width Horizontal B-Porch Horizontal Display Horizontal F-Porch Horizontal Total (c) VGA-350 Mode (Hsync = Positive Polarization) Item A B C D E Description Horizontal Width Horizontal B-Porch Horizontal Display Horizontal F-Porch Horizontal Total The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:11 PD064VT4 (5) Detail of Vertical Timing : Vp Vpw Vsync Vbp Vdp Vfp Display period . (a) VGA-480 Mode (Vsync = Positive / Negative Polarization) Item A B C D E Description Vertical Width Vertical B-Porch Vertical Display Vertical F-Porch Vertical Total Horizontal Lines 2 33 480 10 525 Time 63.5 μs 1.049 ms 15.253 ms 317.8 μs 16.683 ms Horizontal Lines 2 35 400 12 449 Time 63.5 μs 1.112 ms 12.711 ms 381.0 μs 14.268 ms Horizontal Lines 2 60 350 37 449 Time 63.5 μs 1.907 ms 11.122 ms 1.176 μs 14.268 ms (b) VGA-400 Mode (Vsync = Positive Polarization) Item A B C D E Description Vertical Width Vertical B-Porch Vertical Display Vertical F-Porch Vertical Total (c) VGA-350 Mode (Vsync = Negative Polarization) Item A B C D E Description Vertical Width Vertical B-Porch Vertical Display Vertical F-Porch Vertical Total The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:12 PD064VT4 7-6) Vertical Display Position Mode Hsync VGA-480 Positive / Negative VGA-400 Negative VGA-350 Positive Vsync V-Start Position Positive / Negative 34 Positive 17 Negative 30 V-Display Remark 480 lines 400 lines Note 7-7 350 lines Note 7-8 Note 7-7 :As the format is VGA-400 (Hsync = Negative , Vsync = Positive) , LCD module will adjust the display area to the center of display . At this time , both of the upper and lower display areas have 40 blanking lines (the display color is black) . The actual display area is center 400 lines . 4 0 B la n k in g L in e s 4 0 0 D is p la y L in e s 4 0 B la n k in g L in e s Note 7-8 : As the format is VGA-350 (Hsync = Positive, Vsync = Negative) , LCD module will adjust the display area to the center of display . At this time , both of the upper and lower display areas have 65 blanking lines (the display color is black) . The actual display area is center 350 lines . 65 Blankin g Lines 350 Dis p la y Lines 65Blankin g Lines The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:13 PD064VT4 7-7) Display Color and Gray Scale Reference Color Basic Colors Red Green Blue Black Red (63) Green (63) Blue (63) Cyan Magenta Yellow White Red (00) Red (01) Red (02) Darker ↓ Brighter Red (61) Red (62) Red (63) Green (00) Green (01) Green (02) Darker ↓ Brighter Green (61) Green (62) Green (63) Blue (00) Blue (01) Blue (02) Darker ↓ Brighter Blue (61) Blue (62) Blue (63) R5 0 1 0 0 0 1 1 1 0 0 0 R4 0 1 0 0 0 1 1 1 0 0 0 Red R3 R2 0 0 1 1 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 R1 0 1 0 0 0 1 1 1 0 0 1 R0 0 1 0 0 0 1 1 1 0 1 0 Input Color Data Green G5 G4 G3 G2 G1 G0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B5 0 0 0 1 1 1 0 1 0 0 0 B4 0 0 0 1 1 1 0 1 0 0 0 Blue B3 B2 0 0 0 0 0 0 1 1 1 1 1 1 0 0 1 1 0 0 0 0 0 0 B1 0 0 0 1 1 1 0 1 0 0 0 B0 0 0 0 1 1 1 0 1 0 0 0 ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 0 1 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:14 PD064VT4 7-8) Control Board Dip Switch Format SW1(8 Pins) Item Symbol Condition SW 1-1 No connection SW 1-2 HP3 Horizontal Shift (8 Line) SW 1-3 HP2 Horizontal Shift (4 Line) SW 1-4 HP1 Horizontal Shift (2 Line) SW 1-5 HP0 Horizontal Shift (1 Line) SW 1-6 VP2 Vertical Shift (4 Line) SW 1-7 VP1 Vertical Shift (2 Line) SW 1-8 VP0 Vertical Shift (1Line) 1. The default state is base on SYNC. mode (VGA-480) 2. Total horizontal shift line are 15 lines (HP0~HP3 on) Total vertical shift line are 7 lines (VP0~VP2 on) SW2 (2 Pins) Item Symbol SW 2-1 UD SW 2-2 RL Remark Default (OFF) Default (ON) Default (OFF) Default (OFF) Default (ON) Default (OFF) Default (ON) Default (ON) Condition Vertical Image Shift-direction Select Horizontal Image Shift-direction Select Remark Default (ON) Default (ON) 8. Power On Sequence 3.0 V 0 s< t <35 ms 0 s< t <35 ms 3.0 V VCC Signal 35ms 0<17ms Backlight 1. The supply voltage for input signals should be same as VCC. 2. When the power is off , please keep whole signals (Hsync, Vsync, CLK, Data) low level or high impedance The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:15 PD064VT4 9. Optical Characteristic 9-1) Specification: Parameter Horizontal Viewing Angle Vertical Symbol θ21, θ22 θ12 θ11 Contrast Ratio CR Rise Fall Response time Brightness Uniformity Cross Talk White Chromaticity Lamp Life Time Tr Tf L U x y - Condition CR＞10 At optimized Viewing angle θ=0° θ=0° θ=0° θ=0° +25℃ MIN. 55 35 50 200 TYP. MAX. Unit 60 deg 40 deg 55 deg 400 - - 15 30 ms 25 50 ms 350 400 cd/㎡ 75 80 % 3.5 % 0.264 0.294 0.324 0.276 0.308 0.338 50,000 hr Ta=25℃ Remarks Note 9-1 Note 9-2 Note 9-4 Note 9-3 Note 9-5 Note 9-6 Note 9-3 Note 9-1 : The definitions of viewing angle diagrams : Note 9-2 : CR = Luminance when LCD is White Luminance when LCD is Black Contrast Ratio is measured in optimum common electrode voltage. Note 9-3 : 1.Topcon BM-7 (fast) luminance meter 1°field of view is used in the testing (after 20~30 minutes operation). 2.Lamp current : 6 mA 3.Inverter model : TDK-347. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:16 PD064VT4 Note 9-4 : The definitions of response time White Black White 100% 90% Brightness 10% 0% Tr Tf Note 9-5 : The uniformity of LCD is defined as U = The Minimum Brightness of the 9 testing Points The Maximum Brightness of the 9 testing Points Luminance meter : BM-5A or BM-7 fast (TOPCON) Measurement distance : 500 mm +/- 50 mm Ambient illumination : < 1 Lux Measuring direction : Perpendicular to the surface of module The test pattern is white (Gray Level 63). 1/6 2/6 2/6 1/6 1/6 2/6 2/6 1/6 The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:17 PD064VT4 Note 9-6 : Cross Talk (CTK) = ⏐YA-YB⏐ YA YA : Brightness of Pattern A YB : Brightness of Pattern B ×100% Pattern A Pattern B (Gray Level 46) (Gray Level 46, central black box exclusive) YA YB 1/3 1/3 1/3 1/3 1/3 1/3 Black : Testing Point (A and B are at the same point.) (Gray Level 0) The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:18 PD064VT4 10. Handling Cautions 10-1) Mounting of module a) Please power off the module when you connect the input/output connector. b) Please connect the ground pattern of the inverter circuit surely. If the connection is not perfect, some following problems may happen possibly. 1.The noise from the backlight unit will increase. 2.The output from inverter circuit will be unstable. 3.In some cases a part of module will heat. c) Polarizer which is made of soft material and susceptible to flaw must be handled carefully. d) Protective film (Laminator) is applied on surface to protect it against scratches and dirt. It is recommended to peel off the laminator before use and taking care of static electricity. 10-2) Precautions in mounting a) When metal part of the TFT-LCD module (shielding lid and rear case) is soiled, wipe it with soft dry cloth. b) Wipe off water drops or finger grease immediately. Long contact with water may cause discoloration or spots. c) TFT-LCD module uses glass, which breaks or cracks easily if dropped or bumped on hard surface. Please handle with care. d) Since CMOS LSI is used in the module. So take care of static electricity and earth yourself when handling. 10-3) Adjusting module a) Adjusting volumes on the rear face of the module have been set optimally before shipment. b) Therefore, do not change any adjusted values. If adjusted values are changed, the specifications described may not be satisfied. 10-4) Others a) Do not expose the module to direct sunlight or intensive ultraviolet rays for many hours. b) Store the module at a room temperature place. c) The voltage of beginning electric discharge may over the normal voltage because of leakage current from approach conductor by to draw lump read lead line around. d) If LCD panel breaks, it is possibly that the liquid crystal escapes from the panel. Avoid putting it into eyes or mouth. When liquid crystal sticks on hands, clothes or feet. Wash it out immediately with soap. e) Observe all other precautionary requirements in handling general electronic components. f) Please adjust the voltage of common electrode as material of attachment by 1 module. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:19 PD064VT4 11. Reliability Test No 1 2 3 4 Test Item High Temperature Storage Test Low Temperature Storage Test High Temperature Operation Test Low Temperature Operation Test High Temperature & High Humidity 5 Operation Test Thermal Cycling Test 6 (non-operating) 7 Shock Test (non-operating) 8 Vibration Test (non-operating) 9 Electrostatic Discharge Test (non-operating) Test Condition Ta = +80 ℃, 240 hrs Ta = -30 ℃, 240 hrs Ta = +70 ℃, 240 hrs Ta = -20 ℃, 240 hrs Ta = +60 ℃, 90%RH, 240 hrs -25℃ → +70℃, 200 Cycles 30 min 30 min Gravity :490m/s Direction: ±X, ±Y, ±Z Pulse Width :11ms,half sine wave Frequency：10 ~ 57 HZ /Vibration Width :0.075mm 58-500 H/ / Gravity :9.8m/s Sweep time: 11 minutes Test period: 3 hrs for each direction of X, Y, Z 150pF, 330Ω Air : ±15KV ; Contact : ±8KV 10 times/point , 9 points/panel face Ta: ambient temperature Note : The protective film must be removed before temperature test. [Criteria] In the standard conditions, there is not display function NG issue occurred. (Including: line defect, no image). All the cosmetic specification is judged before the reliability stress. The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:20 PD064VT4 12. Block Diagram VL B a c k lig h t GND IC V 1 IC V 2 IC V 3 1 2 3 IC H1 V SYNC R [5 :0 ] 2 3 Control Board CLK 1920 1 H SYNC DENB IC V 4 T F T -L C D D is p la y A re a G [5 :0 ] IC H2 B [5 :0 ] RL 478 479 480 UD GND B a c k lig h t VL The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:21 PD064VT4 13. Packing The information contained herein is the exclusive property of Prime View International Co., Ltd. and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of Prime View International Co., Ltd. Page:22