TSL235 LIGHT-TO-FREQUENCY CONVERTER SOES012 – SEPTEMBER 1994 • • • • • • • High-Resolution Conversion of Light Intensity to Frequency With No External Components Communicates Directly With a Microcontroller Compact Three-Leaded Clear-Plastic Package Single-Supply Operation Down to 2.7 V Nonlinearity Error Typically 0.2% at 100 kHz Stable 100 ppm/°C Temperature Coefficient Advanced LinCMOS Technology description The TSL235 light-to-frequency converter combines a silicon photodiode and a current-to-frequency converter on a single monolithic CMOS integrated circuit. The output is a square wave (50% duty cycle) with frequency directly proportional to light intensity. Because it is TTL compatible, the output allows direct interface to a microcontroller or other logic circuitry. The device has been temperature compensated for the ultravioletto-visible light range of 300 nm to 700 nm and responds over the light range of 300 nm to 1100 nm. The TSL235 is characterized for operation over the temperature range of – 25°C to 70°C. mechanical data The TSL235 is offered in a clear-plastic three-leaded package. The photodiode area is 1.36 mm2 (0.0029 in2). 2,0 (0.079) T.P.† 0,75 (0.030) 0,65 (0.026) 2,25 (0.089) 1,75 (0.069) 0,635 (0.025) 0,4 (0.016) Pin 1 Pin 2 Pin 3 1,25 (0.049) 0,75 (0.029) GND VDD OUT 1 2 4,0 (0.157) T.P.† 3 1 2 2,05 (0.081) 1,55 (0.061) 0,65 (0.026) 0,55 (0.022) 0,86 (0.034) 0,46 (0.018) 15,7 (0.619) 13,2 (0.520) 3,05 (0.120) 2,55 (0.100) 4,8 (0.189) 4,4 (0.173) 4,85 (0.191) 4,35 (0.171) 0,85 (0.033) 0,35 (0.014) 0,75 (0.030) R 0,51 (0.02) 0,385 (0.015) 3 5,05 (0.199) 4,55 (0.179) 1,75 (0.069) 1,25 (0.049) 4,35 (0.171) 3,85 (0.152) 2,74 (0.108) 2,34 (0.092) † True position when unit is installed. ALL LINEAR DIMENSIONS ARE IN MILLIMETERS AND PARENTHETICALLY IN INCHES Advanced LinCMOS is a trademark of Texas Instruments Incorporated. Copyright 1994, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 TSL235 LIGHT-TO-FREQUENCY CONVERTER SOES012 – SEPTEMBER 1994 functional block diagram Light Current-to-Frequency Converter Photodiode Output absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5 V Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 25°C to 70°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 25°C to 85°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltage values are with respect to GND. recommended operating conditions Supply voltage, VDD Operating free-air temperature range, TA MIN NOM 2.7 5 – 25 MAX UNIT 6 V 70 °C electrical characteristics at VDD = 5 V, TA = 25°C (unless otherwise noted) PARAMETER VOH VOL High-level output voltage IDD Supply current TEST CONDITIONS IOH = – 4 mA IOL = 4 mA Low-level output voltage Full-scale frequency‡ MIN 4 TYP MAX 4.3 V 0.17 0.26 2 3 500 Temperature coefficient of output frequency λ ≤ 700 nm, –25°C ≤ TA ≤ 70°C V mA kHz ± 100 kSVS Supply-voltage sensitivity VDD = 5 V ±10% ‡ Full-scale frequency is the maximum operating frequency of the device without saturation. UNIT ppm/°C 0.5 %/ V operating characteristics at VDD = 5 V, TA = 25°C PARAMETER fO Output frequency TEST CONDITIONS MIN TYP MAX UNIT Ee = 375 µW/cm2, λp = 670 nm 200 250 300 kHz 0.25 10 Ee = 0 fO = 0 kHz to 10 kHz Nonlinearity § fO = 0 kHz to 100 kHz %F.S. ± 0.2% %F.S. 1 pulse of new frequency plus 1 µs Step response to full-scale step input ‡ Full-scale frequency is the maximum operating frequency of the device without saturation. § Nonlinearity is defined as the deviation of fO from a straight line between zero and full scale, expressed as a percent of full scale. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 Hz ± 0.1% TSL235 LIGHT-TO-FREQUENCY CONVERTER SOES012 – SEPTEMBER 1994 TYPICAL CHARACTERISTICS OUTPUT FREQUENCY vs IRRADIANCE PHOTODIODE SPECTRAL RESPONSIVITY 1 1000 0.8 Normalized Responsivity 100 fO – Output Frequency – kHz TA = 25°C VDD = 5 V λp = 670 nm TA = 25°C 10 1 0.1 0.6 0.4 0.2 0.01 0.001 0.001 0.01 0.1 1 10 10 0 0 300 1k 400 Ee – Irradiance – µW/cm2 500 600 fO(dark) – Dark Frequency – Hz VDD = 5 V Ee = 0 10 1 0.1 50 75 TA – Temperature – °C Temperature Coefficient of Output Frequency – ppm/ °C 100 25 1000 1100 Figure 2 DARK FREQUENCY vs TEMPERATURE 0 900 800 λ – Wavelength – nm Figure 1 0.01 – 25 700 TEMPERATURE COEFFICIENT OF OUTPUT FREQUENCY vs WAVELENGTH OF INCIDENT LIGHT 10000 VDD = 5 V TA = 25°C to 70°C 8000 6000 4000 2000 0 300 400 500 600 700 800 900 1000 λ – Wavelength of Incident Light – nm Figure 3 Figure 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 TSL235 LIGHT-TO-FREQUENCY CONVERTER SOES012 – SEPTEMBER 1994 TYPICAL CHARACTERISTICS OUTPUT FREQUENCY vs SUPPLY VOLTAGE 1.005 Normalized Output Frequency 1.004 TA = 25°C fO = 500 kHz 1.003 1.002 1.001 1 0.999 0.998 0.997 0.996 0.995 2.5 3 3.5 4 4.5 5 5.5 VDD – Supply Voltage – V Figure 5 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 6 TSL235 LIGHT-TO-FREQUENCY CONVERTER SOES012 – SEPTEMBER 1994 APPLICATION INFORMATION power-supply considerations For optimum device performance, power-supply lines should be decoupled by a 0.01-µF to 0.1-µF capacitor with short leads (see Figure 6). output interface The output of the device is designed to drive a standard TTL or CMOS logic input over short distances. If lines greater than 12 inches are used on the output, a buffer or line driver is recommended. measuring the frequency The choice of interface and measurement technique depends on the desired resolution and data-acquisition rate. For maximum data-acquisition rate, period-measurement techniques are used. Period measurement requires the use of a fast reference clock with available resolution directly related to reference-clock rate. The technique is employed to measure rapidly varying light levels or to make a fast measurement of a constant light source. Maximum resolution and accuracy may be obtained using frequency-measurement, pulse-accumulation, or integration techniques. Frequency measurements provide the added benefit of averaging out random- or high-frequency variations (jitter) resulting from noise in the light signal. Resolution is limited mainly by available counter registers and allowable measurement time. Frequency measurement is well suited for slowly varying or constant light levels and for reading average light levels over short periods of time. Integration, the accumulation of pulses over a very long period of time, can be used to measure exposure – the amount of light present in an area over a given time period. VDD 0.1 µF 2 TSL235 3 1 Timer / Port MCU Figure 6. Typical TSL235 Interface to a Microcontroller POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated