DATA SHEET NEC's 6-PIN DIP PS7142-1A 400 V BREAK DOWN VOLTAGE PS7142L-1A 1-CH OPTICAL COUPLED MOS FET FEATURES DESCRIPTION • 1 cHANNEL TYPE: 1 a Output NEC's PS7142-1A and PS7142L-1A are solid state relays containing GaAs LEDs on the light emitting side (input side) and MOS FETs on the output side. • LOW LED OPERATING CURRENT: IF= 2mA • DESIGNED FOR AC/DC SWITCHING LINE CHANGER They are suitable for analog signal control because of their low offset and high linearity. • SMALL PACKAGE: 6-Pin DIP The PS7142L-1A has a surface mount type lead. • LOW OFFSET VOLTAGE • PS7142L-1A: Surface mount type • SAFETY STANDARDS: UL approved: File No. E72422 (S) BSI approved: File No. 8245/8246 CSA approved: File No. CA 101391 APPLICATION • Exchange Equipment • Measurement Equipment • FA/OA Equipment California Eastern Laboratories PS7142-1A, PS7142L-1A PACKAGE DIMENSIONS (UNIT: mm) PS7142-1A TOP VIEW 9.25±0.5 6 5 4 1 2 3 1. LED Anode 2. LED Cathode 3. NC 4. MOS FET Drain 5. MOS FET Source 6. MOS FET Drain 7.62 3.5±0.3 3.3±0.3 4.15±0.3 6.5±0.5 0.5±0.1 1.34±0.1 0.25 M 0 to 15º 2.54 PS7142L-1A TOP VIEW 9.25±0.5 6 5 4 1 2 3 1. LED Anode 2. LED Cathode 3. NC 4. MOS FET Drain 5. MOS FET Source 6. MOS FET Drain 3.5±0.3 0.10+0.10 -0.05 6.5±0.5 1.34±0.1 0.25 M 2.54 0.9±0.25 9.60±0.4 PS7142-1A, PS7142L-1A ORDERING INFORMATION (Pb-Free) Part Number PS7142-1A-A Package 6-pin DIP Packing Style Magazine case 50 pcs PS7142L-1A-A PS7142L-1A-E3-A Application Part Number *1 PS7142-1A PS7142L-1A Embossed Tape 1000 pcs/reel PS7142L-1A-E4-A *1 For the application of the Safety Standard, following part number should be used. PS7142-1A, PS7142L-1A ABSOLUTE MAXIMUM RATINGS (TA = 25ºC, unless otherwise Specified) Parameter Diode MOS FET Symbol Ratings Unit Forward Current (DC) IF 50 mA Reverse Voltage VR 5.0 V Power Dissipation PD 50 mW Peak Forward Current *1 IFP 1 A Break Down Voltage VL 400 V IL 200 mA Continuous Load Current *2 Connection A Connection B 250 Connection C 400 Pulse Load Current *3 ILP 400 mA (AC/DC Connection) Power Dissipation PD 560 mW Isolation Voltage *4 BV 1 500 Vr.m.s. Total Power Dissipation PT 610 mW Operating Ambient Temperature TA −40 to +85 °C Storage Temperature Tstg −40 to +100 °C *1 PW = 100 µs, Duty Cycle = 1 % *2 Conditions: IF ≥ 2 mA. The following types of load connections are available. Connection A Connection B Connection C 1 2 3 1 2 3 1 2 3 1 2 3 6 5 4 6 5 IL IL L L 4 6 5 4 6 5 IL 4 IL IL L L IL + IL VL (AC/DC) + VL (DC) + VL (DC) + VL (DC) - *3 PW = 100 ms, 1 shot *4 AC voltage for 1 minute at TA = 25 °C, RH = 60 % between input and output PS7142-1A, PS7142L-1A RECOMMENDED OPERATING CONDITIONS Parameter Symbol MIN. TYP. LED Operating Current IF 2 10 LED Off Voltage VF 0 ELECTRICAL CHARACTERISTICS Parameter Diode MOS FET Coupled (TA = 25ºC) MAX. Unit 20 mA 0.5 V (TA = 25ºC) Symbol Conditions MIN. TYP. MAX. Unit 1.2 1.4 V 5.0 µA 1.0 µA Forward Voltage VF IF = 10 mA Reverse Current IR VR = 5 V Off-state Leakage Current ILoff VD = 400 V 0.03 Output Capacitance Cout VD = 0 V, f = 1 MHz 225 LED On-state Current IFon IL = 200 mA On-state Resistance Ron1 IF = 10 mA, IL = 10 mA Ron2 IF = 10 mA, IL = 200 mA, t ≤ 10 ms Turn-on Time *1 ton IF = 10 mA, VO = 5 V, RL = 500 Ω, Turn-off Time *1 toff PW ≥ 10 ms Isolation Resistance RI-O VI-O = 1.0 kVDC Isolation Capacitance CI-O V = 0 V, f = 1 MHz 10 pF 2.0 mA 6.0 10 Ω 0.8 5.0 ms 0.02 0.2 Ω 9 1.1 pF *1 Test Circuit for Switching Time Pulse Input IF VL 50 % Input 0 Input monitor VO monitor Rin RL VO = 5 V 90 % Output 10 % ton toff PS7142-1A, PS7142L-1A TYPICAL CHARACTERISTICS (TA = 25ºC, unless otherwise specified) MAXIMUM LORD CURRENT vs. AMBIENT TEMPERATURE 300 100 Maximum Load Current IL (mA) Maximum Forward Current IF (mA) MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE 80 60 40 20 0 -25 0 25 7585 50 25 7585 50 Ambient Temperature TA (ºC) Ambient Temperature TA (ºC) FORWARD VOLTAGE vs. AMBIENT TEMPERATURE OUTPUT CAPACITANCE vs. APPLIED VOLTAGE 1.6 1.4 Output Capacitance Cout (pF) IF = 50 mA 30 mA 20 mA 10 mA 5 mA 1 mA 1.2 1.0 0 25 50 75 100 f = 1 MHz 200 150 100 50 0 100 20 40 60 80 100 120 Ambient Temperature TA (ºC) Applied Voltage VD (V) OFF-STATE LEAKAGE CURRENT vs. APPLIED VOLTAGE LORD CURRENT vs. LORD VOLTAGE -5 300 TA = 85 ºC IF = 10 mA 200 10-6 Load Current IL (mA) Forward Voltage VF (V) 0 250 0.8 -25 Off-state Leakage Current ILoff (A) 100 0 -25 100 1.8 10 200 10-7 25 ºC 10-8 100 -1.5 -1.0 -0.5 0 0.5 -100 -200 10-9 0 100 200 300 Applied Voltage VD (V) 400 500 -300 Load Voltage VL (V) 1.0 1.5 PS7142-1A, PS7142L-1A 3.0 ON-STATE RESISTANCE DISTRIBUTION 30 Normalized to 1.0 at TA = 25 ºC, IF = 10 mA, IL = 10 mA 2.5 2.0 1.5 1.0 0.0 -25 0 25 50 75 15 10 0 100 5.0 5.5 6.0 6.5 7.0 Ambient Temperature TA (ºC) On-state Resistance Ron (Ω) TURN-ON TIME vs. FORWARD CURRENT TURN-OFF TIME vs. FORWARD CURRENT 0.6 VO = 5 V 4 3 2 0.4 0.3 0.2 0.1 1 0 5 10 15 20 25 0 30 Forward Current IF (mA) 10 15 20 15 10 n = 50 pcs, IF = 10 mA, VO = 5 V 25 Number (pcs) 20 20 15 10 5 5 0.6 0.7 0.8 0.9 Turn-on Time ton (ms) 25 TURN-OFF TIME DISTRIBUTION 30 n = 50 pcs, IF = 10 mA, VO = 5 V 25 5 Forward Current IF (mA) TURN-ON TIME DISTRIBUTION 30 0 VO = 5 V 0.5 Turn-off Time toff (ms) 5 Turn-on Time ton (ms) 20 5 0.5 6 Number (pcs) n = 50 pcs, IF = 10 mA, IL = 10 mA 25 Number (pcs) Normalized On-state Resistance Ron NORMALIZED ON-STATE RESISTANCE vs. AMBIENT TEMPERATURE 1.0 0 0.02 0.03 Turn-off Time toff (ms) 30 PS7142-1A, PS7142L-1A NORMALIZED TURN-ON TIME vs. AMBIENT TEMPERATURE Normalized to 1.0 at TA = 25 ºC, IF = 10 mA, VO = 5 V 2.5 2.0 1.5 1.0 0.5 0.0 -25 0 25 50 75 Ambient Temperature TA (ºC) Remark The graphs indicate nominal characteristics. 100 3.0 Normalized Turn-off Time toff Normalized Turn-on Time ton 3.0 NORMALIZED TURN-OFF TIME vs. AMBIENT TEMPERATURE Normalized to 1.0 at TA = 25 ºC, IF = 10 mA, VO = 5 V 2.5 2.0 1.5 1.0 0.5 0.0 -25 0 25 50 75 Ambient Temperature TA (ºC) 100 PS7142-1A, PS7142L-1A 7.5±0.1 1.5 +0.1 -0 4.5 MAX. 10.3±0.1 2.0±0.1 4.0±0.1 16.0±0.3 Outline and Dimensions (Tape) 1.75±0.1 TAPING SPECIFICATIONS (UNIT:mm) 4.0±0.1 10.4±0.1 1.55±0.1 12.0±0.1 0.3 Tape Direction PS7142L-1A-E3 PS7142L-1A-E4 Outline and Dimensions (Reel) 2.0±0.5 21.0±0.8 100±1.0 R 1.0 330±2.0 2.0±0.5 13.0±0.2 17.5±1.0 21.5±1.0 Packing: 1 000 pcs/reel 15.9 to 19.4 Outer edge of flange PS7142-1A, PS7142L-1A RECOMMENDED SOLDERING CONDITIONS (1) Infrared reflow soldering •Peak reflow temperature 260°C or below (package surface temperature) •Time of peak reflow temperature 10 seconds or less •Time of temperature higher than 220°C 60 seconds or less •Time to preheat temperature from 120 to 180°C 120±30 s •Number of reflows Three •Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) Package Surface Temperature T (ºC) Recommended Temperature Profile of Infrared Reflow (heating) to 10 s 260ºC MAX. 220ºC to 60 s 180ºC 120ºC 120±30 s (preheating) Time (s) (2) Wave soldering • Temperature 260°C or below (molten solder temperature) • Time 10 seconds or less • Preheating conditions 120°C or below (package surface temperature) • Number of times One •Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. 04/20/2005 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Concentration Limit per RoHS (values are not yet fixed) Concentration contained in CEL devices -A Not Detected Lead (Pb) < 1000 PPM Mercury < 1000 PPM Not Detected Cadmium < 100 PPM Not Detected Hexavalent Chromium < 1000 PPM Not Detected PBB < 1000 PPM Not Detected PBDE < 1000 PPM Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.